Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polycrystalline material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Conductivity of materials made of aluminum nitride and silicon nitride mixtures

To establish the possible mechanism for conductivity in aluminum nitride a study was made of the electric conductivity of pure AlN and its mixtures with silicon nitride at different temperatures and partial pressures of nitrogen in the gas phase. The thermoelectromotive force was also measured. The experiments used polycrystalline samples of cylindrical shape 18 mm in diameter made of powders by hot pressing in graphite press molds at a temperature of 1973-2273 K and pressure 1,470,000 n/sqm. The items obtained by this method had porosity not over 5%. After pressing, the samples were machined to remove carbon from the surface, and were annealed in a stream of dry ammonia for 10 h at a temperature of 1273-1373 K. Electric conductivity was measured according to the bridge scheme on an alternating current of frequency 10 kHz. In order to guarantee close contact of the platinum electrodes with the surface of the samples, a thin layer of platinum was sprayed on them. Experiments were conducted in the temperature interval 1273-1573 K with a half hour delay at each assigned temperature with heating and cooling.

Gorbatov, A. G.↗
DOE OSTI2020

Structural, Electronic, and Thermal Properties of CdSnAs 2

Structural, electrical, and thermal properties of CdSnAs 2 , with analyses from temperature-dependent transport properties over a large temperature range, are reported. Phase-pure microcrystalline powders were synthesized that were subsequently densified to a high-density homogeneous polycrystalline specimen for this study. Temperature-dependent transport indicates n-type semiconducting behavior with a very high and nearly temperature independent mobility over the entire measured temperature range, attributed to the very small electron effective mass of this material. The Debye model was successfully applied to model the thermal conductivity and specific heat. Furthermore, this work contributes to the fundamental understanding of this material, providing further insight and allowing for investigations into altering this and related physical properties of these materials for technological applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1985

Phenomenological study of the behavior of some silica formers in a high velocity jet fuel burner

Samples of four silica formers: single crystal SiC, sintered alpha-SiC, reaction sintered Si3N4 and polycrystalline MoSi2, were subjected to a Mach 1 jet fuel burner for 1 hr, at a sample temperature of 1375 deg C (2500 deg F). Two phenomena were identified which may be deleterious to a gas turbine application of these materials. The glass layer formed on the MoSi2 deformed appreciably under the aerodynamic load. A scale developed on the samples of the other materials which consisted of particular matter from the gas stream entrapped in a SiO2 matrix.

Cawley, J. D.↗
NASA NTRS1992

Edge-defined contact heater apparatus and method for floating zone crystal growth

An apparatus for growing a monocrystalline body (30) from a polycrystalline feed rod (22) includes a heater (20) that is positioned to heat a short section of the polycrystalline rod (22) to create a molten zone (34). The heater (20) is formed to include a shaper (40) that contacts the polycrystalline rod (22) in the molten zone (34) and has a hole (46) to allow flow in the molten zone (34) between the polycrystalline rod (22) side and the monocrystalline body (30) side of the shaper. The shaper (40) has an edge (42) that defines the boundary of the cross-section of the monocrystalline body (30) that is formed as the molten material solidifies.

Kou, Sindo↗
DOE OSTI2026

Cs X Si 15 P 21 ( X = Sn or Pb): Polar Noncentrosymmetric Si–P Frameworks Stabilized by Covalent X –P Bonding

Metal silicon phosphides composed of earth-abundant Si and P tend to exhibit semiconducting properties and adopt diverse crystal structures with relatively small additions of structure-directing elements. The potential of silicon phosphide materials in nonlinear optical applications has been hindered by the inability to systematically produce noncentrosymmetric structures with such a flexible framework. Here, in this work, two isostructural compounds with a novel noncentrosymmetric structure were made possible by the inclusion of elements with stereochemically active lone pairs (Sn 2+ and Pb 2+ ). The structures were determined through single-crystal and synchrotron powder X-ray diffraction. Analysis of chemical bonding in real space through the electron localization function revealed stereochemically active Pb 2+ and Sn 2+ species in a trigonal pyramidal coordination with {Pb/Sn}–P bonds. Such covalent bonding between Pb and P is quite uncommon in extended solids and has been reported in a few rare instances. Band structure calculations and linear optical measurements confirm the semiconducting nature of Cs X Si 15 P 21 ( X = Sn or Pb). The synthesis was optimized to yield high-purity polycrystalline samples. The nonlinear optical properties show promising second-harmonic generation (SHG) coefficients from the Kurtz–Perry method. First-principles calculations of the nonlinear optical properties support the experimentally determined SHG values and provide moderate values of birefringence, suggesting Cs X Si 15 P 21 could be phase-matchable and practical nonlinear optical materials in the mid-IR region.

crystal structure↗
DOE OSTI2022

Solidification and grain formation in alloys: a 2D application of the grand-potential-based phase-field approach

Solidification is a significant step in the forming of crystalline structures during various manufacturing and material processing techniques. Solidification characteristics and the microstructures formed during the process dictate the properties and performance of the materials. Hence, understanding how the process conditions relate to various microstructure formations is paramount. In this work, a grand-potential-based multi-phase, multi-component, multi-order-parameter phase-field model is used to demonstrate the solidification of alloys in 2D. This model has several key advantages over other multi-phase models such as it decouples the bulk energy from the interfacial energy, removes the constraints for the phase concentration variable, and prevents spurious third-phase formation at the two phase interfaces. Here, the model is implemented in a finite-element-based phase-field modeling code. The role of various modeling parameters in governing the solidification rate and the shape of the solidified structure is evaluated. It is demonstrated that the process conditions such as temperature gradient, thermal diffusion, cooling rate, etc, influence the solidification characteristics by altering the level of undercooling. Furthermore, the capability of the model to capture directional solidification and polycrystalline structure formation exhibiting various grain shapes is illustrated. In both these cases, the process conditions have been related to the growth rate and associated shape of the dendritic structure. As a result, this work serves as a stepping stone towards resolving the larger problem of understanding the process–structure–property–performance correlation in solidified materials.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Upcycling Polycrystalline LiNi1/3Mn1/3Co1/3O2 to High-Performance Large-Grained LiNi0.6Mn0.2Co0.2O2 via Simplified Polyol-Mediated Recycling

The escalating demand for lithium-ion batteries (LIBs) necessitates advanced recycling strategies that can address both resource scarcity and environmental impact. While conventional hydrometallurgy shows promise, it is challenged by complexity, impurity management, and environmental footprint. Here, we report a strategic polyol-metallurgy recycling process that efficiently transforms spent polycrystalline LiNi1/3Mn1/3Co1/3O2 (NMC111) into high-performance large-grained LiNi0.6Mn0.2Co0.2O2 (NMC622), offering dual benefits of compositional upcycling and morphology upgradation. Our approach leverages a polyol system with meticulous control over nickel salt addition and the precipitation process. This yields upcycled cathode materials possessing excellent structural integrity, well-defined large-grained particles (5-10?..mu..m), and robust electrochemical performance, including a specific capacity of ~182 mAh g-1 at C/10 and 88.0% capacity retention after 100 cycles. This facile and multifunctional process provides an environmental-friendly pathway for advanced cathode recycling, significantly contributing to a circular economy for LIBs through precise control over critical material attributes.

25 ENERGY STORAGE↗
DOE OSTI2025

Controlling Preferred Grain Orientation in Vapor-Deposited Metal-Halide Perovskite Thin Films

Metal-halide perovskites are promising semiconductor materials for light-absorber layers in solar cells due to their optimized band gap, defect tolerance, and relative ease of synthesis. In this work, we demonstrate the viability of vapor transport deposition (VTD), a solvent-free processing method, to realize polycrystalline films of both lead iodide (PbI 2 ) and methylammonium lead iodide (MAPbI 3 ) perovskites showing preferential crystallographic orientation. Notable is the difference in perovskite film texturing observed for sequentially and co-deposited VTD films of MAPbI 3 , as well as the lack of strong preferential orientation in solution-processed MAPbI 3 films. While sequential deposition of the perovskite precursors PbI 2 and methylammonium iodide (MAI) leads to a MAPbI 3 film with a limited preferential grain orientation, co-deposited MAPbI 3 films mirror the orientation of excess PbI 2 present in the film. The latter is confirmed by the similar dependence of preferential orientation for PbI 2 and co-deposited MAPbI 3 on underlayer roughness, as well as the emergence of preferential orientation in MAPbI 3 only when excess PbI 2 is present. Both MAPbI 3 and PbI 2 films show a strong preferred lattice orientation on smooth substrates, while on rougher substrates, this orientation is disrupted. Furthermore, these results are interpreted as excess PbI 2 frustrating the diffusion of MAI in the film, which would otherwise disrupt the preferred orientation, pointing to a notable difference in lattice orientation arising from processing technique and conditions.

Deposition↗
NASA NTRS1981

Schottky barrier solar cell

A method of fabricating a Schottky barrier solar cell is described. The cell consists of a thin substrate of low cost material with at least the top surface of the substrate being electrically conductive. A thin layer of heavily doped n-type polycrystalling germanium is deposited on the substrate after a passivation layer is deposited to prevent migration of impurities into the polycrystalline germanium. The polycrystalline germanium is recrystallized to increase the crystal sizes to serve as a base layer on which a thin layer of gallium arsenide is vapor-epitaxilly grown followed by a thermally-grown oxide layer. A metal layer is deposited on the oxide layer and a grid electrode is deposited to be in electrical contact with the top surface of the metal layer.

Stirn, R. J.↗
DOE OSTI2024

Growth of ultra-flat ultra-thin alkali antimonide photocathode films

Ultra-flat, ultra-thin alkali antimonide photocathodes with high crystallinity can exhibit high quantum efficiency and low mean transverse energy of outgoing electrons, which are essential requirements for a variety of applications for photocathode materials. Here, we investigate the growth of Cs 3 Sb on graphene-coated 4H–SiC (Gr/4H–SiC), 3C–SiC, and Si 3 N 4 substrates. Sb is deposited using pulsed laser deposition, while Cs is deposited thermally and simultaneously. We demonstrate, employing x-ray analysis and quantum efficiency measurements, that this growth method yields atomically smooth Cs 3 Sb photocathodes with a high quantum efficiency (>10%), even in the ultra-thin limit (<30 nm). For the Si 3 N 4 substrate, film growth is shown to be polycrystalline, while films grown on Gr/4H–SiC show a high degree of ordering with signs of epitaxy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electrodeposition of ligand-free copper nanoparticles from aqueous nanodroplets

Copper nanoparticles have emerged as promising electrocatalysts for energy storage and conversion. Generally, homogenous nanoparticle synthesis requires a stabilizing ligand, which may influence the electrocatalysis. Ligands can be avoided by direct nanoparticle electrodeposition. Here, we extend nanodroplet-mediated electrodeposition to the electrodeposition of copper nanoparticles from aqueous nanodroplets suspended in 0.1 M tetrabutylammonium hexafluorophosphate ([TBA][PF 6 ]) and 1,2-dichloroethane. Stochastic electrochemistry on microelectrodes was used to elucidate nanoparticle growth kinetics for various solution conditions and substrate materials. A study on the effect of surfactants on nanoparticle morphology and growth kinetics demonstrated the surfactant's role as an avenue for morphological control. Nanoparticle morphology was studied by Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM). Energy-dispersive X-ray Spectroscopy (EDX) confirmed the presence of copper nanoparticles. TEM and Selected Area Electron Diffraction (SAED) confirmed nanoparticle size, morphology, and polycrystallinity. We demonstrate tunable nanoparticle size using cyclic voltammetry on single aqueous nanodroplets by altering the voltammetric sweeping potentials of copper electroreduction. Finite element simulations validate the voltammetric response and ability to control the nanoparticle size with nanometer resolution during a voltammetric sweep. These results inform the electrodeposition of copper nanoparticles from aqueous nanodroplets for important applications, such as the conversion of CO 2 to hydrocarbon fuels.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Auger spectroscopy analysis in adhesion, friction and wear studies

The paper reviews the current use of Auger electron spectroscopy in adhesion, friction, wear and lubrication studies. Conventional Auger spectroscopy is adopted to complement LEED studies of the adhesion of metal single crystals. In addition, Auger cylindrical mirror analysis is applied to the study of changes in surface chemistry during dynamic friction and wear experiments on polycrystalline metals and alloys. Important conclusions are that (1) segregation of alloying elements to the surface of metals can alter adhesion behavior; (2) hydrocarbons are adsorbed readily to clean iron surfaces at 23 C; (3) transfer from one surface to another for dissimilar materials in contact can be followed in sliding or rubbing friction studies; and (4) the friction process can enhance surface activity for metals with hydrocarbons.

Buckley, D. H.↗
NASA NTRS1984

Deformation and erosion of f.c.c. metals and alloys under cavitation attack

Experimental investigations have been conducted to determine the early stages of cavitation attack on 6061-T6 aluminum alloy, electrolytic tough pitch copper, brass, and bronze, all having polycrystalline fcc matrices. The surface profiles and scanning electron micrographs show that the pits are initially formed at the grain boundaries, while the grain surfaces are progressively roughened by multiple slip and twinning. The initial erosion is noted to have occurred from the material in the grain boundaries, as well as by fragmentation of part of the grains. Further erosion occurred by shearing and necking of the surface undulations caused by plastic deformation. The mean penetration depth, computed on the basis of mass loss, was lowest on the bronze and greatest on the copper. Attention is given to the relation of cavitation attack to grain size, glide stress and stacking fault energy.

Rao, B. C. S.↗
NASA NTRS1988

Fatigue life prediction modeling for turbine hot section materials

This paper presents a summary of the life prediction methods developed under the NASA Lewis Research Center's Hot Section Technology (HOST) program. A major objective of the fatigue and fracture efforts under the HOST program was to significantly improve the analytic life prediction tools used by the aeronautical gas turbine engine industry. This has been achieved in the areas of high-temperature thermal and mechanical fatigue of bare and coated high-temperature superalloys. Such technical improvements will eventually reduce life cycle costs. The cyclic crack initiation and propagation resistance of nominally isotropic polycrystalline alloys and highly anisotropic single crystal alloys has been addressed. A sizeable data base has been generated for three alloys [cast PWA 1455 (B-1900 + Hf), wrought Inconel 718, and cast single crystal PWA 1480] in bare and coated conditions. Two coatings systems, diffusion aluminide (PWA 273) and plasma sprayed MCrAIY overlay (PWA 286) were employed. Life prediction modeling efforts were devoted to creep-fatigue interaction, oxidation, coatings interactions, multiaxiality of stress-strain states, mean stress effects, cumulative damage, and thermomechanical fatigue. The fatigue crack initiation life models developed to date include the Cyclic Damage Accumulation (CDA) Model of Pratt & Whitney and the Total Strain Version of Strainrange Partitioning (TS-SRP) of NASA Lewis for nominally isotropic materials, and the Tensile Hysteretic Energy Model of Pratt & Whitney for anisotropic superalloys. The fatigue model being developed by the General Electric Company is based upon the concepts of Path-lndependent Integrals (PII) for describing cyclic crack growth under complex nonlinear response at the crack tip due to thermomechanical loading conditions. A micromechanistic oxidation crack extension model has been derived by researchers at Syracuse University. The models are described and discussed in the paper. Only limited verification has been achieved to-date as several of the technical programs are still in progress and the verification tasks are scheduled, quite naturally, near the conclusion of the program. To-date, efforts have concentrated on development of independent models for cyclic constitutive behavior, cyclic crack initiation, and cyclic crack propagation. The transition between crack initiation and crack propagation has not been thoroughly researched as yet, and the integration of these models into a unified life prediction method has not been addressed.

Metal fatigue↗
DOE OSTI2025

Unraveling fundamental mechanisms of silicon nitride crystallization in microelectronics manufacturing

This research project investigates the fundamental mechanisms of silicon nitride (SiN) crystallization, aiming to enhance the understanding of this critical material in microelectronics manufacturing. Through a collaborative effort between Sandia National Laboratories, the University of Tennessee, and the University of Florida, we developed a comprehensive framework that integrates experimental techniques, atomistic modeling, meso-scale simulations, and an integrated multi-scale model to capture this physical phenomenon on multiple time and length scales . The project developed a new machine learning based atomistic potential and utilized advanced phase field modeling to capture the complexities of polycrystalline growth and the influence of mechanical stresses on crystallization dynamics. By employing a grain tracker algorithm, the meso-scale model effectively identified and tracked individual crystal grains, enabling the simulation of anisotropic growth behaviors reflective of SiN’s physical properties. The integration of atomistic simulations with meso-scale modeling created a powerful multi-scale framework that validated atomistic inputs and enhanced predictive accuracy for crystallization dynamics at larger scales, validated experimentally. This adaptable modeling capability not only accelerates development times by informing manufacturing processes but also serves as a valuable starting point for understanding crystallization physics in similar materials. The insights gained from this research unlock new opportunities for the development of advanced materials tailored for future microelectronics and photonics applications. Overall, this project represents a significant advancement in understanding of fundamental physics of SiN and establishes a foundation for future research in material science, bridging the gap between atomic-level phenomena and macroscopic material behaviors for practical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Capacity Fade of Graphite/NMC811: Influence of Particle Morphology, Electrolyte, and Charge Voltage

LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) is an important Li-ion battery cathode material; however, there is a tradeoff between delivered capacity and capacity retention. As the charge potential increases the capacity rises but at the expense of capacity retention. The decrease in capacity retention has been ascribed to several factors including particle cracking, surface reconstruction, transition metal dissolution, and electrolyte reactivity. The present study compares 4.1 and 4.3 V charging limits in commercially relevant graphite/NMC811 pouch cells for single crystal (SC) and polycrystalline (PC) NMC811 with ethylene carbonate (EC)-containing or EC-free electrolytes. The electrochemistry is rationalized through analysis of electrochemical impedance spectroscopy, positive electrode X-ray photoelectron spectroscopy, soft X-ray absorption spectroscopy, X-ray diffraction, and negative electrode mapping by X-ray fluorescence. Graphite/SC-NMC811 cells show high-capacity retention at 4.1 V but exhibit degradation at 4.3 V charging potentials. The EC-free electrolyte cells led to higher capacity fade, especially when charged to 4.3 V. Cathode dissolution and deposition on the negative electrode from PC-NMC811 cells was higher than for samples from SC-NMC811 cells. This study reveals the impact of material type, charge voltage, and electrolyte composition on the reactions at the positive electrode, their influence on the negative electrode, and evolution with cycle number.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High dopant activation in arsenic doped single-crystal CdTe thin films: Insights from MBE growth and rapid thermal processing

Single-crystal model systems are valuable tools to investigate fundamental material properties. In this work, we use molecular beam epitaxy to deposit in situ arsenic (As) doped single-crystal CdTe films on large area Si substrates to better understand As doping for photovoltaic applications. We found that As incorporation is highly temperature dependent: a substrate temperature difference of 50 °C can lead to several orders of magnitude difference in As concentration. Cd overpressure during in situ doping may limit out-diffusion of As but decrease As incorporation, especially at lower growth temperatures. Carrier concentrations greater than 10 16 cm −3 can be achieved with or without Cd overpressure when annealed at temperatures above 500 °C. However, unlike the low (∼1% to 5%) dopant activation commonly observed in polycrystalline CdTe, our films achieve significantly higher activation ratios—exceeding 50%, and in some cases approaching 80%. These values are consistent with or exceed prior reports in single-crystal CdTe systems. In addition to as-deposited arsenic concentrations, we also consider arsenic distribution after different rapid thermal processing temperatures. We propose a detailed definition and description of how arsenic incorporation is considered and calculated. Due to carrier concentration saturation, As incorporation also needs to be controlled to average levels of 10 17 cm −3 to achieve high activation. These findings suggest that higher annealing temperature regimes may be beneficial to polycrystalline CdTe based PV devices.

36 MATERIALS SCIENCE↗