Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “operational analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Operating Stresses and Their Effects on Degradation of LSM-Based SOFC Cathodes

The performance of solid oxides fuel cells (SOFCs) with four different Mn excess of lanthanum strontium manganite (LSM) -based cathodes were examined under different temperatures (1,000 °C, 900 °C), current densities (0, 380, and 760 mA cm -2 ), and cathode atmospheres (p O 2 )=0.1,0.15,0.21) for durations ranging from 58 to 1,008 h. Each yttria-stabilized zirconia (YSZ) electrolyte-supported “button” cell had a porous Ni/YSZ composite anode and a porous LSM/YSZ composite cathode. The cells’ output voltage versus time were recorded and electrochemical impedance spectroscopy (EIS) and linear sweep voltammetry (LSV) measurements were performed every 24 hours. The total area specific resistance (ASR) was calculated from these measurements. The values of ASR from both EIS and LSV were comparable between each other but lower than that from durability test. Distribution of relaxation times (DRT) analysis was performed to investigate the electrochemical processes and their corresponding relaxation frequencies as well as their attributions to the total ASR. The series resistance and parallel resistance that obtained from the equivalent circuit fit of the Nyquist plot were higher at low temperature and low p O 2 regardless of LSM compositions. The area of the peaks derived from DRT analysis increased with time during individual tests. The microstructures of the tested cells were examined using scanning electron microscopy and energy-dispersive x-ray spectroscopy (SEM/EDS). Manganese oxide particles were observed near the cathode-electrolyte interface after prolonged (1,008 h) testing in air of a cell with LSM of 11% manganese excess, and after a short test (58 h) under low oxygen (p O 2 = 0.10) in a cell with LSM of 5% manganese excess. However, the role of MnOx in cell degradation is still unknown.

08 HYDROGEN↗
NASA NTRS2013

Mars-GRAM 2010: Additions and Resulting Improvements

The Mars Global Reference Atmospheric Model (Mars-GRAM) is an engineering-level atmospheric model widely used for diverse mission applications. Mars-GRAM has been utilized during previous aerobraking operations in the atmosphere of Mars. Mars-GRAM has also been used in the prediction and validation of Mars Pathfinder hypersonic aerodynamics, the aerothermodynamic and entry dynamics studies for Mars Polar Lander, the landing site selection process for the Mars Science Laboratory (MSL), the Mars Aerocapture System Study (MASS) as well as the Aerocapture Technology Assessment Group (TAG). Most recently, Mars-GRAM 2010 was used to develop the onboard atmospheric density estimator that is part of the Autonomous Aerobraking Development Plan. The most recent release of Mars-GRAM 2010 contains several changes including an update to Fortran 90/95 and the addition of adjustment factors. Following the completion of a comparison analysis between Mars-GRAM, Thermal Emission Spectrometer (TES), as well as Mars Global Surveyor (MGS), Mars Odyssey (ODY), and Mars Reconnaissance Orbiter (MRO) aerobraking density data, adjustment factors were added to Mars-GRAM 2010 that alter the input data from National Aeronautics and Space Administration (NASA) Ames Mars General Circulation Model (MGCM) and the University of Michigan Mars Thermospheric General Circulation Model (MTGCM) for the mapping year 0 user-controlled dust case. The addition of adjustment factors resolved the issue of previous versions of Mars-GRAM being less than realistic when used for sensitivity studies for mapping year 0 and large optical depth values, such as tau equal to 3. Mars-GRAM was evaluated at locations and times of TES limb observations and adjustment factors were determined. For altitudes above 80 km and below 135 km, Mars-GRAM (MTGCM) densities were compared to aerobraking densities measured by Mars Global Surveyor (MGS), Mars Odyssey (ODY), and Mars Reconnaissance Orbiter (MRO) to determine the adjustment factors. The adjustment factors generated by this process had to satisfy the gas law as well as the hydrostatic relation and are expressed as a function of height (z), Latitude (Lat) and areocentric solar longitude (Ls). The greatest adjustments are made at large optical depths such as tau greater than 1. The addition of the adjustment factors has led to better correspondence to TES Limb data from 0-60 km altitude as well as better agreement with MGS, ODY and MRO data at approximately 90-130 km altitude. Improved Mars-GRAM atmospheric simulations for various locations, times and dust conditions on Mars will be presented at the workshop session. The latest results validating Mars-GRAM 2010 versus Mars Climate Sounder data will also be presented. Mars-GRAM 2010 updates have resulted in improved atmospheric simulations which will be very important when beginning systems design, performance analysis, and operations planning for future aerocapture, aerobraking or landed missions to Mars.

Justh, Hilary L.↗
NASA NTRS2019

Evaluation Analysis of NASA SMAP L3 and L4 and SPoRT-LIS Soil Moisture Data in the United States

Soil moisture has a critical role in the development, frequency and persistence of climatic and hydrologic extremes such as drought, heat wave and flooding events. In situ soil moisture data are uneven and sparse in time and space. This highlights the need to utilize other soil moisture sources to fill this spatiotemporal gap. The goal of this study is to validate one satellite-based and two model-based soil moisture datasets with in situ data across the United States. Soil moisture information from the Soil Moisture Active Passive (SMAP) enhanced level 3 (L3) (SMAP L3) and modeled level 4 (L4) (SMAP L4) data at 9-km resolution and Short-term Prediction Research and Transition-Land Information System (SPoRT-LIS) modeled at 3-km resolution were selected for evaluation. SPoRT-LIS is a near real-time, high resolution operational land analysis data. Ground-based data were obtained from the North American Soil Moisture Database (NASMD) for 362 stations. Seven statistical indicators including anomaly, Spearman, and Pearson correlation coefficients, the systematic error (Bias), root mean square error (RMSE), unbiased root mean square error (ubRMSE), and normalized standard deviation (SDV) were used to evaluate the satellite- and model-derived soil moisture data. In addition, the triple collocation (TC) error model was used to measure the error among SMAP L4, SPoRT-LIS and ground-based data. This study assesses which satellite or modeled dataset is most appropriate for specific times and locations to use as a surrogate for in situ observations. Temporal and spatial analysis demonstrated that, overall, SMAP L4 performed better than SMAP L3 and SPoRT-LIS. Strong agreement was observed between SMAP L4 and in situ observations (ρ = 0.53, Bias = −0.006) in all seasons and most regions with various land covers, especially in winter and in the central regions of the United States. For croplands, SMAP L4 presented the best agreement with in situ data, analyzing all period (ρ = 0.60) and non-winter period (ρ = 0.61) separately.

Tavakol, Ameneh↗
NASA NTRS1990

A new environment for multiple spacecraft power subsystem mission operations

The engineering analysis subsystem environment (EASE) is being developed to enable fewer controllers to monitor and control power and other spacecraft engineering subsystems. The EASE prototype has been developed to support simultaneous real-time monitoring of several spacecraft engineering subsystems. It is being designed to assist with offline analysis of telemetry data to determine trends, and to help formulate uplink commands to the spacecraft. An early version of the EASE prototype has been installed in the JPL Space Flight Operations Facility for online testing. The EASE prototype is installed in the Galileo Mission Support Area. The underlying concept, development, and testing of the EASE prototype and how it will aid in the ground operations of spacecraft power subsystems are discussed.

Bahrami, K. A.↗
NASA NTRS1992

GUIs in the MIDAS environment

MIDAS (Munich Image Data Analysis System) is the image processing system developed at ESO for astronomical data reduction. MIDAS is used for off-line data reduction at ESO and many astronomical institutes all over Europe. In addition to a set of general commands, enabling to process and analyze images, catalogs, graphics and tables, MIDAS includes specialized packages dedicated to astronomical applications or to specific ESO instruments. Several graphical interfaces are available in the MIDAS environment: XHelp provides an interactive help facility, and XLong and XEchelle enable data reduction of long-slip and echelle spectra. GUI builders facilitate the development of interfaces. All ESO interfaces comply to the ESO User Interfaces Common Conventions which secures an identical look and feel for telescope operations, data analysis, and archives.

Ballester, P.↗
NASA NTRSDate not supplied

Application of Objectives-Driven Assurance Cases to System Development in an Evolving Acquisition Model

System properties such as “safety” and “dependability” cannot, in practice, be proven, and must be argued in an “assurance case” aimed at supporting risk-acceptance decisions that have to be made by system acquirers and/or regulatory authorities. The paper is concerned with applications of the “assurance case” idea early in design and development of new systems, when (apart from dedicated testing) the only available operating experience information derives from previous (non-identical) systems. Much of the discussion is based on an evolving acquisition model at the US National Aeronautics and Space Administration; previously, most major systems were developed in-house, but some major systems will now be developed by and acquired from commercial providers. Key points discussed include the following. (1) By promoting a particular kind of focused discussion between acquirers and providers, the use of assurance cases should be particularly valuable under the new acquisition model. (2) In principle, objectives-driven (sometimes called “performance-based”) approaches to assurance of performance have significant advantages in cases where they are applicable. (3) For truly novel systems, completeness of the safety analysis is a significant issue; it is important for the assurance case to include a commitment by the provider (or applicant) to seriously pursue analysis of operating experience, so that previously unrecognized hazards can be identified and addressed. (4) Inquiries into major accidents often point to deficiencies in management oversight in all parts of the life cycle; management processes need to be addressed in the formulation and the implementation of an assurance case. Under the new acquisition model, these considerations imply a serious reconsideration of the way in which the development process is managed by both providers and acquirers.

Objectives-driven↗
NASA NTRS1981

Low cost solar aray project: Experimental process system development unit for producing semiconductor-grade silicon using the silane-to-silicon process

This phase consists of the engineering design, fabrication, assembly, operation, economic analysis, and process support R&D for an Experimental Process System Development Unit (EPSDU). The mechanical bid package was issued and the bid responses are under evaluation. Similarly, the electrical bid package was issued, however, responses are not yet due. The majority of all equipment is on order or has been received at the EPSDU site. The pyrolysis/consolidation process design package was issued. Preparation of process and instrumentation diagram for the free-space reactor was started. In the area of melting/consolidation, Kayex successfully melted chunk silicon and have produced silicon shot. The free-space reactor powder was successfully transported pneumatically from a storage bin to the auger feeder twenty-five feet up and was melted. The fluid-bed PDU has successfully operated at silane feed concentrations up to 21%. The writing of the operating manual has started. Overall, the design phase is nearing completion.

Source record↗
DOE OSTI2020

Free-Surface Liquid Lithium Flow Modeling and Stability Analysis for Fusion Applications

Liquid metal plasma facing components are considered an attractive design choice for fusion devices including pilot plants. Virtual prototyping of such devices includes modeling of free-surface flow of the electrically conductive liquid, which requires computational fluid dynamics (CFD) and magnetohydrodynamics (MHD) simulations. Numerical tools capable of simulating flows and heat transfer in the free-surface MHD flow were developed at PPPL based on the customized ANSYS CFX. Here, MHD is introduced using a magnetic vector potential approach. Free-surface flow capabilities are available in the code and were tested. Special stabilization procedures were derived and applied to improve convergence of the momentum equations with the source terms due to the Lorentz force and surface tension. Important characteristics of the fusion-relevant liquid metal flow is free surface smoothness and stability. Heat flux from the plasma impacts the liquid surface at a very acute angle, so any change of the free surface from axisymmetry can dramatically increase the local heat flux density and thus create excessive evaporation of liquid lithium into the plasma, which is detrimental to operations. Stability analysis of the liquid metal film flow was performed to determine applicable flow regimes. Thin film flow along horizontal wall is considered. Effects of gravity, magnetic field, and surface tension are included in the analysis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2013

Analysis of a Split-Plot Experimental Design Applied to a Low-Speed Wind Tunnel Investigation

A procedure to analyze a split-plot experimental design featuring two input factors, two levels of randomization, and two error structures in a low-speed wind tunnel investigation of a small-scale model of a fighter airplane configuration is described in this report. Standard commercially-available statistical software was used to analyze the test results obtained in a randomization-restricted environment often encountered in wind tunnel testing. The input factors were differential horizontal stabilizer incidence and the angle of attack. The response variables were the aerodynamic coefficients of lift, drag, and pitching moment. Using split-plot terminology, the whole plot, or difficult-to-change, factor was the differential horizontal stabilizer incidence, and the subplot, or easy-to-change, factor was the angle of attack. The whole plot and subplot factors were both tested at three levels. Degrees of freedom for the whole plot error were provided by replication in the form of three blocks, or replicates, which were intended to simulate three consecutive days of wind tunnel facility operation. The analysis was conducted in three stages, which yielded the estimated mean squares, multiple regression function coefficients, and corresponding tests of significance for all individual terms at the whole plot and subplot levels for the three aerodynamic response variables. The estimated regression functions included main effects and two-factor interaction for the lift coefficient, main effects, two-factor interaction, and quadratic effects for the drag coefficient, and only main effects for the pitching moment coefficient.

Erickson, Gary E.↗
NASA NTRS2002

Formal verification of human-automation interaction

This paper discusses a formal and rigorous approach to the analysis of operator interaction with machines. It addresses the acute problem of detecting design errors in human-machine interaction and focuses on verifying the correctness of the interaction in complex and automated control systems. The paper describes a systematic methodology for evaluating whether the interface provides the necessary information about the machine to enable the operator to perform a specified task successfully and unambiguously. It also addresses the adequacy of information provided to the user via training material (e.g., user manual) about the machine's behavior. The essentials of the methodology, which can be automated and applied to the verification of large systems, are illustrated by several examples and through a case study of pilot interaction with an autopilot aboard a modern commercial aircraft. The expected application of this methodology is an augmentation and enhancement, by formal verification, of human-automation interfaces.

Aviation↗
NASA NTRS2018

The OpenSE Cookbook: A Practical, Recipe Based Collection of Patterns, Procedures, and Best Practices for Executable Systems Engineering for the Thirty Meter Telescope

The OpenSE Cookbook is an open-sourced collection of patterns, procedures, and best practices targeted for systems engineers who seek guidance on applying model-based and executable systems engineering (MBSE) using SysML. Its content has emerged from the system level modeling effort on the European Framework Program 6 (FP6) and the Thirty Meter Telescope (TMT). The TMT MBSE approach applied the Executable Systems Engineering Method (ESEM) and the open-source Engineering Environment (OpenMBEE) to specify, analyze, and verify requirements of TMT’s Alignment and Phasing System (APS) and the Narrow Field Infrared Adaptive Optics System (NFIRAOS). In these applications, implicit dependencies are made explicit in a formal model through the use of ESEM, OpenMBEE, and SysML modeling constructs. The value proposition for applying this MBSE approach was to establish precise requirements and fine-grained traceability to system designs, and to verify key requirements beginning early in development. The integration of ESEM and the OpenMBEE tooling infrastructure (providing linked-data and web-operability) is a significant added value for the MBSE approach. The APS is responsible for the overall pre-adaptive optics wavefront quality, using starlight to measure wavefront errors and align the TMT optics. In the formally integrated and executable SysML model, simulations are performed to analyze the impact of changed requirements and verify specified constraints for various operational scenarios. The APS team used several modeling patterns to capture information such as the requirements, the operational scenarios, involved subsystems and their interaction points, the estimated or required time durations, and the mass and power consumption. Adaptive optics systems are designed to sense real-time atmospheric turbulence and correct the telescope’s optical beam to remove its effect. The system model for the adaptive optics operational modes was developed to capture sequence behaviors and operational scenarios to run Monte-Carlo simulations for verifying acquisition time, observing efficiency, and operational behavior requirements. The model is particularly useful for investigating the effect of parallelization, identifying interface issues, and re-ordering sequence acquisition tasks. A former version of the Cookbook (which is now updated to MBSE challenges, goals, and lessons learned) included modeling guidelines and conventions for all system aspects, hierarchy levels, and views, which were developed during for the Active Phasing Experiment (APE), an opto-mechatronical system technology demonstrator for the Extremely Large Telescope (ELT). The Cookbook utilizes the above mentioned system models as real-world case-studies to demonstrate and document the applications of the recipes, providing also instructional examples and addressing the available tooling support. The Cookbook is accompanied by a number of SysML models and aodel libraries which facilitate model authoring and maintenance. The Cookbook covers the different aspects of Systems Engineering such as management of Requirements, Design (behavior and structure), Interfaces, Interdisciplinary Integration, Analysis, Trade Studies, and Technical Resources. This paper presents the background, motivation, architecture, and highlights some key content of the Cookbook. For example, interface management, error budget management, requirements verification, Monte Carlo driven analysis, and timing analysis of operational scenarios. The paper discusses how the capabilities of OpenMBEE contributed significantly to the adoption of executable systems engineering.

Brower, Eric↗
DOE OSTI2024

Hadamard products and BPS networks

We study examples of fourth-order Picard-Fuchs operators that are Hadamard products of two second-order Picard-Fuchs operators. Each second-order Picard-Fuchs operator is associated with a family of elliptic curves, and the Hadamard product computes period integrals on the fibred product of the two elliptic surfaces. We construct 3-cycles on this geometry as the union of 2-cycles in the fibre over contours on the base. We then use the special Lagrangian condition to constrain the contours on the base. This leads to a construction that is reminiscent of spectral networks and exponential networks that have previously appeared in string theory literature.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1992

A land-surface testbed for EOSDIS

We propose to develop an on-line data distribution and interactive display system for the collection, archival, distribution and analysis of operational weather satellite data for applications in land surface studies. A 1,000 sq km scene of the western U.S. (centered on the Colorado Rockies) will be extracted from Advanced Very High Resolution Radiometer (AVHRR) imagery collected from morning and afternoon passes of the NOAA polar-orbiters at the direct readout stations operated by CU/CCAR. All five channels of these AVHRR data will be navigated and map registered at CU/CCAR and then be transferred to NCAR for storage in an on-line data system. Software will also be available at NCAR to process and navigate the raw AVHRR data as needed. A display workstation software, based on a Macintosh II computer, will be developed that will display and further process the AVHRR data for studies of vegetation monitoring and snowpack assessment. Various options of presently used techniques for both vegetation and snowpack monitoring will be implemented in the workstation software to provide the individual investigator with the freedom to interact with the satellite image data. The display software will be freely distributed online to interested investigators and the AVHRR data will be made available on-line to anyone interested. In addition, potential users will be sought out and connected to the on-line data archive. This experiment with an active on-line archive and interactive analysis systems will provide experience with a small scale EOSDIS.

Emery, William↗
NASA NTRS1993

A land-surface testbed for EOSDIS

We propose to develop an on-line data distribution and interactive display system for the collection, archival, distribution and analysis of operational weather satellite data for applications in land surface studies. A 1,000 square km scene of the western U.S. (centered on the Colorado Rockies) will be extracted from Advanced Very High Resolution Radiometer (AVHRR) imagery collected from morning and afternoon passes of the NOAA polar-orbiters at the direct readout stations operated by CU/CCAR. All five channels of these AVHRR data will be navigated and map registered at CU/CCAR and then be transferred to NCAR for storage in an on-line data system. Software will also be available at NCAR to process and navigate the raw AVHRR data as needed. A display workstation software, based on a Macintosh II computer, will be developed that will display and further process the AVHRR data for studies of vegetation monitoring and snowpack assessment. Various options of presently used techniques for both vegetation and snowpack monitoring will be implemented in the workstation software to provide the individual investigator with the freedom to interact with the satellite image data. The display software will be freely distrributed online to interested investigators, and the AVHRR data will be made available on-line to anyone interested. In addition, potential users will be sought out and connected to the on-line data archive. This experiment with an active on-line archive and interactive analysis systems will provide experience with a small scale EOSDIS.

Emery, William↗
NASA NTRS2012

Development of Human System Integration at NASA

Human Systems Integration seeks to design systems around the capabilities and limitations of the humans which use and interact with the system, ensuring greater efficiency of use, reduced error rates, and less rework in the design, manufacturing and operational deployment of hardware and software. One of the primary goals of HSI is to get the human factors practitioner involved early in the design process. In doing so, the aim is to reduce future budget costs and resources in redesign and training. By the preliminary design phase of a project nearly 80% of the total cost of the project is locked in. Potential design changes recommended by evaluations past this point will have little effect due to lack of funding or a huge cost in terms of resources to make changes. Three key concepts define an effective HSI program. First, systems are comprised of hardware, software, and the human, all of which operate within an environment. Too often, engineers and developers fail to consider the human capacity or requirements as part of the system. This leads to poor task allocation within the system. To promote ideal task allocation, it is critical that the human element be considered early in system development. Poor design, or designs that do not adequately consider the human component, could negatively affect physical or mental performance, as well as, social behavior. Second, successful HSI depends upon integration and collaboration of all the domains that represent acquisition efforts. Too often, these domains exist as independent disciplines due to the location of expertise within the service structure. Proper implementation of HSI through participation would help to integrate these domains and disciplines to leverage and apply their interdependencies to attain an optimal design. Via this process domain interests can be integrated to perform effective HSI through trade-offs and collaboration. This provides a common basis upon which to make knowledgeable decisions. Finally, HSI must be considered early in the requirements development phase of system design and acquisition. This will provide the best opportunity to maximize return on investment (ROI) and system performance. HSI requirements must be developed in conjunction with capability ]based requirements generation through functional. HSI requirements will drive HSI metrics and embed HSI issues within the system design. After a system is designed, implementation of HSI oversights can be very expensive. An HSI program should be included as an integral part of a total system approach to vehicle and habitat development. This would include, but not limited to, workstation design, D&C development, volumetric analysis, training, operations, and human -robotic interaction. HSI is a necessary process for Human Space Flight programs to meet the Agency Human ]System standards and thus mitigate human risks to acceptable levels. NASA has been involved in HSI planning, procedures development, process, and implementation for many years, and has been building several internal and publicly accessible products to facilitate HSI fs inclusion in the NASA Systems Engineering Lifecycle. Some of these products include: NASA STD 3001 Volumes 1 and 2, Human Integration Design Handbook, NASA HSI Implementation Plan, NASA HSI Implementation Plan Templates, NASA HSI Implementation Handbook, and a 2 ]hour short course on HSI delivered as part of the NASA Space and Life Sciences Directorate Academy. These products have been created leveraging industry best practices and lessons learned from other Federal Government agencies.

Whitmore, Mihriban↗
NASA NTRS2015

Software Development: 3D Animations and Creating User Interfaces for Realistic Simulations

My fall 2015 semester was spent at the Lyndon B. Johnson Space Center working in the Integrated Graphics, Operations, and Analysis Laboratory (IGOAL). My first project was to create a video animation that could tell the story of OMICS. OMICS is a term being used in the field of biomedical science to describe the collective technologies that study biological systems, such as what makes up a cell and how it functions with other systems. In the IGOAL I used a large 23 inch Wacom monitor to draw storyboards, graphics, and line art animations. I used Blender as the 3D environment to sculpt, shape, cut or modify the several scenes and models for the video. A challenge creating this video was to take a term used in biomedical science and describe it in such a way that an 8th grade student can understand. I used a line art style because it would visually set the tone for what we thought was an educational style. In order to get a handle on the perspective and overall feel for the animation without overloading my workspace, I split up the 2 minute animation into several scenes. I used Blender's python scripting capabilities which allowed for the addition of plugins to add or modify tools. The scripts can also directly interact with the objects to create naturalistic patterns or movements. After collecting the rendered scenes, I used Blender's built-in video editing workspace to output the animation. My second project was to write software that emulates a physical system's interface. The interface was to simulate a boat, ROV, and winch system. Simulations are a time and cost effective way to test complicated data and provide training for operators without having to use expensive hardware. We created the virtual controls with 3-D Blender models and 2-D graphics, and then add functionality in C# using the Unity game engine. The Unity engine provides several essential behaviors of a simulator, such as the start and update functions. A framework for Unity, which was developed in the lab, provided a way to place the different widgets on the virtual console dock and have them resize correctly based on the window dimensions.. My task in this project was to create the controls and visualizations for the data coming in from the simulator for the boat portion of the project. I wrote a class for each control window to handle the functionality of that widget. I implemented 11 widgets that make up the ship portion of the simulator. The members of the lab were each masters of their craft and I'm glad I had the opportunity to learn from them. I learned to plan strategically so I could finish this project on time. I allotted time for storyboarding, development, and refinement. In regards to animating I learned to use modifiers like lattice, boolean and build deformers. I also learned how to animate with drivers, how to use the dope sheet, and how to use the graph editor. In coding I learned to limit the chances for bugs by privatizing functions that should be exclusive to their class. I learned how to use the GIT repository to commit, stash and pull the latest build. I learned a bit of everything because I had the chance to see the entire application development process from the artwork, to the implementation.

Gordillo, Orlando Enrique↗
DOE OSTI2024

Capabilities Development at the University of Texas at El Paso for Hydrogen Generation Research and Education

Gasification-based systems have recently received much attention due to their capability of converting wastes into useful fuels. The gasification of biomass, municipal solid waste (MSW), plastics, and other sustainable resources has shown promise in hydrogen production. When coupled to a CCU or CCS unit, these systems have the potential to achieve carbon neutrality or carbon-negative emissions. In addition, these systems have an edge over conventional incineration or landfill systems by reducing greenhouse gas emissions and recovering useful energy. However, the gasification of MSW and other wastes is still in its early stages. In particular, co-gasification of wastes with biomass has significant unknowns in optimizing the reaction kinetics, operability, design and performance improvements. Currently, Supercritical Water Gasifiers (SCWG) and Plasma Gasifiers are the major systems that are capable of producing high hydrogen amounts from Biomass and MSW, respectively. However, both systems have high capital and operating costs, adversely affecting efficiency and the hydrogen production cost. Additionally, due to lower temperatures, SCWGs are prone to tar formation and fouling in the heat exchangers. Hence, there is a need to look for alternative solutions for MSW and biomass gasifications, particularly in co-gasification. The current effort aims to develop a strategic plan to establish a sustainable gasification facility for hydrogen research at the University of Texas at El (UTEP). A major part of this effort involves an extensive literature survey to identify technological gaps and potential areas of interest. Several concepts were developed in accordance with the current demands from the literature survey. Based on the concepts, a center-wide capability assessment was conducted to measure the current capacity and feasibility of establishing hydrogen research. Afterward, a strategic research plan was developed, and a list of required resources was made for the expansion of hydrogen research at UTEP. In addition, successful partnerships with the local county and the city were developed to pursue hydrogen research. The strategic goal setting and planning of UTEP Aerospace Center resulted in securing $2.5 million in external support to expand the hydrogen research during the project performance period. In addition, during the project period, a course in Hydrogen Energy Systems was developed to expand the energy curriculum at the UTEP Aerospace and Mechanical Engineering Department. The course focused on hydrogen production, storage, supply and delivery and application. The cross-listed course was offered at both undergraduate and graduate levels during the Spring 2024 semester and had 27 enrolled students. Moreover, the students supported under this award were trained in gasification process modeling, CAD, CFD and FEA during the project period. The training enabled the students to move into new projects to support gasification design, integrated gasification combined cycle process plant analysis, gasifier structural and operational analysis, and digitally threading the systems.

08 HYDROGEN↗