SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Chaos in an Anosov-type mechanical system is eliminated by referring the governing equations to a specially selected rapidly oscillating (non-inertial) frame of reference in which the stabilization effect is caused by inertia forces. The result is generalized to any orbitally unstable mechanical system.
Instrument purchase requirements and dialogue with manufacturers have established hardware parameters for alignment, stability, and reproducibility, which have helped improve the precision and accuracy of electron microprobe analysis (EPMA). The development of correction algorithms and the accurate solution to quantitative analysis problems requires the minimization of systematic errors and relies on internally consistent data sets. Improved hardware and computer systems have resulted in better automation of vacuum systems, stage and wavelength-dispersive spectrometer (WDS) mechanisms, and x-ray detector systems which have improved instrument stability and precision. Improved software now allows extended automated runs involving diverse setups and better integrates digital imaging and quantitative analysis. However, instrumental performance is not regularly maintained, as WDS are aligned and calibrated during installation but few laboratories appear to check and maintain this calibration. In particular, detector deadtime (DT) data is typically assumed rather than measured, due primarily to the difficulty and inconvenience of the measurement process. This is a source of fundamental systematic error in many microprobe laboratories and is unknown to the analyst, as the magnitude of DT correction is not listed in output by microprobe operating systems. The analyst must remain vigilant to deviations in instrumental alignment and calibration, and microprobe system software must conveniently verify the necessary parameters. Microanalysis of mission critical materials requires an ongoing demonstration of instrumental calibration. Possible approaches to improvements in instrument calibration, quality control, and accuracy will be discussed. Development of a set of core requirements based on discussions with users, researchers, and manufacturers can yield documents that improve and unify the methods by which instruments can be calibrated. These results can be used to continue improvements of EPMA.
Degradation mechanisms were investigated for graphite/polysulfone and graphite/epoxy laminates exposed to ultraviolet and high-energy electron radiations in vacuum up to 960 equivalent sun hours and 10 to the ninth power rads respectively. Based on GC and combined GC/MS analysis of volatile by-products evolved during irradiation, several free radical mechanisms of composite degradation were identified. The radiation resistance of different matrices was compared in terms of G values and quantum yields for gas formation. All the composite materials evaluated show high electron radiation stability and relatively low ultraviolet stability as indicated by low G values and high quantum for gas formation. Mechanical property measurements of irradiated samples did not reveal significant changes, with the possible exception of UV exposed polysulfone laminates. Hydrogen and methane were identified as the main by-products of irradiation, along with unexpectedly high levels of CO and CO2.
A tubular strut with an integral mechanism for adjusting its thermal expansivity and length was developed to fulfill the stringent thermal stability requirements anticipated for the metering truss in the Large Space Telescope. Its features may be advantageously applied to a general variety of structures and precision mechanisms where dimensional control of component elements in a dynamic thermal environment is required. Detail, design, fabrication, and test of a developmental strut are discussed.
Comparative numerical studies of four constraint treatment techniques for the simulation of general multibody dynamic systems are presented, and results are presented for the example of a classical crank mechanism and for a simplified version of the seven-link manipulator deployment problem. The staggered stabilization technique (Park, 1986) is found to yield improved accuracy and robustness over Baumgarte's (1972) technique, the singular decomposition technique (Walton and Steeves, 1969), and the penalty technique (Lotstedt, 1979). Furthermore, the staggered stabilization technique offers software modularity, and the only data each solution module needs to exchange with the other is a set of vectors plus a common module to generate the gradient matrix of the constraints, B.
The major focus of this investigation is to study the fundamentals of layer spreading mechanisms during growth of doped Ge (a facet forming material), and to determine the conditions for morphological instability of vicinal solid-liquid interfaces. The investigation will also lead to the determination of the effect of dopants on the layer growth kinetics, step free energy, and dopant capture by the advancing ledges. The theoretical treatment of growth of faceted interfaces indicates that the kinetics of a step on a growing vicinal interface considerably depends on its angle of inclination, the melt concentration, and characteristics of flow currents in the melt. The morphological stability of the interface also depends on these parameters, as well as on the density and spreading velocity of the steps. However, the treatment of the instability of the interface by the layer growth mechanism is rather difficult because it requires exact knowledge of the thermal and solutal fields, hydrodynamics of the melt, and supercooling at the interface. The results of recent space experiments of the principal investigator involving directional solidification of faceted Bi-Sn alloys have shown that the morphological stability of various crystallographic orientations is significantly affected by the anistropy in interfacial properties of the faceted alloy in general, and the interface kinetics in particular. These findings have also raised many important and fundamental questions, particularly with respect to the behavior of interfacial steps, which need to be addressed via additional groundbased and microgravity experiments. For the present investigation we will use a novel crystal growth technique which provides axial heat flux close to the solid-liquid boundary. The Axial Heat Processing (AHP) technique allows for precise control and determination of the heat and mass transfer close to the crystallization front, and the establishment of a planar interface over the entire cross-section of the growing crystal.
It is noted that ethynol (HCCOH), despite the theoretical prediction of its stability to tautomerization to ketene, has thus far not been observed. It is shown here that the identification of this unknown molecule, both in space and in the laboratory, can be aided by an ab initio calculation of spectroscopic parameters. At the HF/3-21G level, harmonic vibrational frequencies are computed by way of analytic second differentiation of the Hartee-Fock (HF) energy with respect to the nuclear coordinates. After applying an empirical scale factor, the resultant frequencies are (per cm) 473, 517, 773, 841, 1003, 1217, 2206, 3285, and 3418. The computed dipole moment at the CISD/DZ+P level is 1.79 D. At the CISD+Q/DZ+P level, the molecule's rotational constants are determined. After scaling by empirical correction factors, they are used in deriving the 4(04) - 3(03) frequency of 76.81 + or - 0.3 GHz with a triplet splitting of 0.30 + or - 0.01 GHz. The triplet splitting involves 4(14) - 3(13) and 4(13) - 3(12) relative to the 4(04) - 3(03) transition as the central line.
The nonlinear dynamics of propellant sloshing during orbital ascent are usually neglected in the flight control analysis of large boost vehicles under the assumption that the viscous damping of the fluid is sufficient to suppress nonlinear phenomena and confine the fluid to small, planar free surface displacements. In this case, the sloshing dynamics can be modeled using a spring-mass-damper or linearized pendulum mechanical analog. However, large, smooth-wall tanks without significant internal hardware or ring baffles are still susceptible to nonlinear effects. In particular, rotary sloshing can present a risk to flight control as it involves the formation of a stable limit cycle which can lead to undesirable roll coupling. The underlying phenomena of jump resonance does not manifest in linear models, but can be reproduced using a nonlinear spherical pendulum or the Bauer paraboloid model developed during the Apollo/Saturn program. In this paper, a detailed analysis of the rotary sloshing dynamics of these mechanical analogs is presented, and discussed in the context of flight control stability. High-fidelity simulations of a representative boost vehicle are used to verify the semi-analytical predictions of the nonlinear dynamic response.
In an attempt to enhance the electrical and mechanical properties of the high temperature superconducting oxides, high T(sub c) composites were prepared composed of the 123 compounds and AgO. The presence of extra oxygen due to the decomposition of AgO at high temperature is found to stabilize the superconducting 123 phase. Ag is found to serve as clean flux for grain growth and precipitates as pinning center. Consequently, almost two orders of magnitude enhancement in critical current densities were also observed in these composites. In addition, these composites also show much improvement in workability and shape formation. On the other hand, proper oxygen treatment of Y5Ba6Cu11Oy was found to possibly stabilize superconducting phase with T(sub c) near 250 K. I-V, ac susceptibility, and electrical resistivity measurements indicate the existence of this ultra high T(sub c) phase in this compound. Detailed structure, microstructure, electrical, magnetic and thermal studies of the superconducting composites and the ultra high T(sub c) compound are presented and discussed.
Poly(arylene ether sulfones) comprise a class of materials known as engineering thermoplastics which have a variety of important applications. These polymers are tough, rigid materials with good mechanical properties over a wide temperature range, and they are processed by conventional methods into products typically having excellent hydrolytic, thermal, oxidative and dimensional stability. Wholly aromatic random copolymers of hydroquinone and biphenol with 4.4 prime dichlorodiphenyl sulfone were synthesized via mechanical nucleophilic displacement. Their structures were characterized and mechanical behavior studied. These tough, ductile copolymers show excellent radiation resistance to electron beam treatment and retain much of the mechanical properties up to at least 700 Mrads under argon.
Consideration is given to mechanically tuned birefringent filters for the spectral range 4500-7500 A with bandpasses as narrow as 50 mA and stability of better than 5 mA. Two tuning techniques are described: optical path change and waveplate tuning. The tuning techniques are mechanically simple and require minimal demands on encoders and drive electronics. Tuning to a random wavelength can be accomplished in less than one second while adjacent wavelengths can be reached in a fraction of a second.
Instability modes of cantilevered bars induced by fluid flow through attached pipes, examining cases of torsional and transverse flutter and torsional buckling
Stability of rotating liquid mass /e.g. earth/, following Jeans treatment of Jacobi ellipsoidal equilibrium configurations
The preparation of a composite material of eutectic composition directly from the molten state is investigated. The manufacture of eutectic composites by unidirectional solidification is reviewed, and it is shown how two-phase composite structures of given relative volume fraction can be produced with a range of particle sizes. Crystallographic relationships and the thermal stability of interfaces in controlled eutectic structures are examined, the mechanical behavior of aligned eutectic microstructures is discussed, and characteristics of eutectic composites having mechanical properties of engineering significance are evaluated. Specific properties of the Ni-Nb eutectic alloy are reviewed to demonstrate the effect of structure control (through directional solidification) on the mechanical response of a eutectic composite. It is noted that unidirectionally solidified eutectic composites possess highly aligned and thermally stable microstructures and also exhibit excellent combinations of strength and ductility to very high temperature levels.
This publication is a compilation of the panel summaries presented in the following areas: systems/operations technology; crew and life support; EVA; crew and life support: ECLSS; attitude, control, and stabilization; human capabilities; auxillary propulsion; fluid management; communications; structures and mechanisms; data management; power; and thermal control. The objective of the workshop was to aid the Space Station Technology Steering Committee in defining and implementing a technology development program to support the establishment of a permanent human presence in space. This compilation will provide the participants and their organizations with the information presented at this workshop in a referenceable format. This information will establish a stepping stone for users of space station technology to develop new technology and plan future tasks.
Some of the most significant advances made in the space station discipline technology program are examined. Technological tasks and advances in the areas of systems/operations, environmental control and life support systems, data management, power, thermal considerations, attitude control and stabilization, auxiliary propulsion, human capabilities, communications, and structures, materials, and mechanisms are discussed. An overview of NASA technology planning to support the initial space station and the evolutionary growth of the space station is given.
A six-axis displacement-stick sidearm controller was developed to enable single-handed control of remote manipulator operations in space. With a working model available, piloted evaluation became possible in a fly-by-computer variable-stability research aircraft, originally a Bell 205 helicopter. The original mechanization was limited to three rotational axes and a linear one, analogous to the collective stick. A newly designed short stickgrip was mounted and the spring force pattern adjusted to suit the helicopter flight control environment. A standard set of test maneuvers was flown by four experimental pilots with conventional helicopter flight controls and with sidearm controllers equipped with two different handgrips. Existing data from flight tests with an isometric-stick controller were added to complete the comparison. The displacement controller consistently achieved a rating of 3.0 to 3.5 on the Cooper-Harper scale, on par with the conventional controls. The same basic controller design was tested in spacecraft and remote manipulator simulations with very promising results. In each application operator/system integration was rapid and positive. The results demonstrate feasibility and support the design philosphy of using deflection as well as force to generate proprioceptive feedback.
The objective of Project 4 was to develop a high-temperature, uncooled gas turbine blade using MA6000 alloy. The program objectives were achieved. Production scale up of the MA6000 alloy was achieved with a fair degree of tolerance to nonoptimum processing. The blade manufacturing process was also optimized. The mechanical, environmental, and physical property evaluations of MA6000 were conducted. The ultimate tensile strength, to about 704 C (130 F), is higher than DS MAR-M 247 but with a corresponding lower tensile elongation. Also, above 982 C (180 F) MA6000 tensile strength does not decrease as rapidly as MAR-M 247 because the ODS mechanism still remains active. Based on oxidation resistance and diffusional stability considerations, NiCrAlY coatings are recommended. CoCrAly coating should be applied on top of a thin NiCrAlY coating. Vibration tests, whirlpit tests, and a high-rotor-rig test were conducted to ensure successful completion of the engine test of the MA6000 TFE731 high pressure turbine blades. The results of these tests were acceptable. In production quantities, the cost of the Project 4 MA6000 blade is estimated to be about twice that of a cast DS MAR-M 247 blade.