Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “local stresses”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

The subtidal response of sea level to atmospheric forcing in the Carolina Capes

The subtidal frequency response of sea level to atmospheric forcing along the coastal region between Cape Hatteras and Charleston is investigated for a four-month period: 1 September-31 December, 1974. It is found that low-frequency sea level fluctuations are preferentially forced by wind stress components which are aligned with the local topography. Also, a localized, one-dimensional model of sea surface response to a clockwise rotating wind for the Charleston coastal regime is developed. The phase spectrum of the alongshore wind component versus sea level as predicted by the model is shown to compare favorably to that derived from actual observations at Charleston, an open ocean coastal site. The model results and observations also suggest that wind-induced fluctuations of coastal sea level are trapped within 40 km of the coast by the combined effects of friction, Coriolis force and bottom topography. The outer shelf is dominated by fluctuations which are less related to wind stress and are attenuated rapidly in the shoreward direction. A reasonable estimate of bottom frictional coefficient, r = 0.05 cm/s, is also established.

Chao, S.-Y.↗
DOE OSTI2020

Real-space formulation of the stress tensor for O (N) density functional theory: Application to high temperature calculations

We present an accurate and efficient real-space formulation of the Hellmann–Feynman stress tensor for O (N) Kohn–Sham density functional theory (DFT). While applicable at any temperature, the formulation is most efficient at high temperature where the Fermi–Dirac distribution becomes smoother and the density matrix becomes correspondingly more localized. We first rewrite the orbital-dependent stress tensor for real-space DFT in terms of the density matrix, thereby making it amenable to O (N) methods. We then describe its evaluation within the O (N) infinite-cell Clenshaw–Curtis Spectral Quadrature (SQ) method, a technique that is applicable to metallic and insulating systems, is highly parallelizable, becomes increasingly efficient with increasing temperature, and provides results corresponding to the infinite crystal without the need of Brillouin zone integration. We demonstrate systematic convergence of the resulting formulation with respect to SQ parameters to exact diagonalization results and show convergence with respect to mesh size to the established plane wave results. Here, we employ the new formulation to compute the viscosity of hydrogen at 10 6 K from Kohn–Sham quantum molecular dynamics, where we find agreement with previous more approximate orbital-free density functional methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1987

The effect of internal stresses on solar cell efficiency

Diffusion induced stresses in silicon are shown to result in large localized changes in the minority carrier mobility which in turn have a significant effect on cell output. Evidence is given that both compressive and tensile stresses can be generated in either the emitter or the base region. Tensile stresses appear to be much more effective in altering cell performance. While most stress related effects appear to degrade cell efficiency, this is not always the case. Evidence is presented showing that arsenic induced stresses can result in emitter characteristics comparable to those found in the MINP cell without requiring a high degree of surface passivation.

Weizer, Victor G.↗
NASA NTRS1999

Assessment of Localized Deformations in Sand Using X-Ray Computed Tomography

The internal fabric and localized deformation patterns of triaxial sand specimens were investigated using Computed Tomography (CT). Three displacement-controlled, conventional, drained axisymmetric (triaxial) experiments were conducted on dry Ottawa sand specimens at very low effective confining stresses (0.05, 0.52, and 1.30 kPa) in a microgravity environment aboard the Space Shuttle during the NASA STS-79 mission. CT scanning was p'erformed on these flight specimens, as well as on an uncompressed specimen and a specimen tested in a terrestrial laboratory at 1.30 kPa effective confining stress. CT demonstrated high accuracy in detecting specimen inhomogeneity and localization patterns. Formation of deformation patterns is dependent on the effective confining stress and gravity. Multiple symmetrical radial shear bands were observed in the specimens tested in a microgravity environment. In the axial direction, two major conical surfaces were developed. Nonsymmetrical spatial deformation was observed in the 1-G specimen. Analysis tools were developed to quantify the spatial density change. Void ratio variation within and outside the shear bands was calculated and discussed.

Alshibli, Khalid A↗
DOE OSTI2020

Local Strain and Polarization Mapping in Ferrielectric Materials

CuInP 2 S 6 (CIPS) is a van der Waals material that has attracted attention because of its unusual properties. Recently, a combination of density functional theory (DFT) calculations and piezoresponse force microscopy (PFM) showed that CIPS is a uniaxial quadruple-well ferrielectric featuring two polar phases and a total of four polarization states that can be controlled by external strain. In this study, we combine DFT and PFM to investigate the stress-dependent piezoelectric properties of CIPS, which have so far remained unexplored. The two different polarization phases are predicted to differ in their mechanical properties and the stress sensitivity of their piezoelectric constants. This knowledge is applied to the interpretation of ferroelectric domain images, which enables investigation of local strain and stress distributions. The interplay of theory and experiment produces polarization maps and layer spacings which we compare to macroscopic X-ray measurements. We found that the sample contains only the low-polarization phase and that domains of one polarization orientation are strained, whereas domains of the opposite polarization direction are fully relaxed. The described nanoscale imaging methodology is applicable to any material for which the relationship between electromechanical and mechanical characteristics is known, providing insight on structural, mechanical, and electromechanical properties down to ~10 nm length scales.

36 MATERIALS SCIENCE↗
NASA NTRS1987

Piezoresistance and solar cell efficiency

Diffusion-induced stresses in silicon are shown to result in large localized changes in the minority-carrier mobility which in turn can have a significant effect on cell output. Evidence is given that both compressive and tensile stresses can be generated in either the emitter or the base region. Tensile stresses in the base appear to be much more effective in altering cell performance than do compressive stresses. While most stress-related effects appear to degrade cell efficiency, this is not always the case. Evidence is presented showing that arsenic-induced stresses can result in emitter characteristics comparable to those found in the MINP cell without requiring a high degree of surface passivation.

Weizer, Victor G.↗
NASA NTRS1977

Biaxial load effects on the crack border elastic strain energy and strain energy rate

The validity of the singular solution (first term of a series representation) is investigated for the crack tip stress and displacement field in an infinite sheet with a flat line crack with biaxial loads applied to the outer boundaries. It is shown that if one retains the second contribution to the series approximations for stress and displacement in the calculation of the local elastic strain energy density and elastic strain energy rate in the crack border region, both these quantities have significant biaxial load dependency. The value of the J-integral does not depend on the presence of the second term of the series expansion for stress and displacement. Thus J(I) is insensitive to the presence of loads applied parallel to the plane of the crack.

Eftis, J.↗
DOE OSTI2020

Precipitation of calcium–alumino–silicate–hydrate gels: The role of the internal stress

Concrete gains its strength from the precipitation of a calcium–alumino–silicate–hydrate (C–A–S–H) colloidal gel, which acts as its binding phase. However, despite concrete’s ubiquity in the building environment, the atomic-scale mechanism of C–A–S–H precipitation is still unclear. Here, we use reactive molecular dynamics simulations to model the early-age precipitation of a C–A–S–H gel. We find that, upon gelation, silicate and aluminate precursors condensate and polymerize to form an aluminosilicate gel network. Notably, we demonstrate that the gelation reaction is driven by the existence of a mismatch of atomic-level internal stress between Si and Al polytopes, which are initially experiencing some local tension and compression, respectively. The polymerization of Si and Al polytopes enables the release of these competitive stresses.

Zhao, Cheng↗
NASA NTRS1993

Global/local interlaminar stress analysis of a grid-stiffened composite panel

A global/local procedure for the computation of the interlaminar stress components at the skin wrap, skin core, and wrap core interfaces for an advanced concept stiffened panel, is described. The procedure consists of a global model of two dimensional shell elements that is used to design a grid stiffened panel with blade type stiffeners, a local model of three dimensional solid elements that is used to compute interlaminar stress components, and a scheme devised to assign displacement boundary conditions for a local model that are based on displacement and rotation data of a few nodes of the global model. A global panel was designed according to strength, stiffness, and stability criteria associated with the design of traditional aircraft wing panels. Interlaminar normal and shearing stress components, computed via the local model, were found to be well below typical tensile normal and shearing strengths of a graphite epoxy material.

Wiggenraad, J. F. M.↗
DOE OSTI2026

Correlation between microstructure and residual stress formation in friction stir welded armor steels characterized by neutron diffraction

Friction stir welding (FSW) is a solid-state joining process that minimizes the heat-affected zone (HAZ) compared with fusion-based arc welding, making it well suited for joining martensitic armor steels where hardness and ballistic resistance are critical. This study investigates residual stress formation in three defect-free FSW butt-joint configurations relevant to armored-vehicle fabrication: similar rolled homogeneous armor (RHA–RHA, Case 1), similar high-hardness armor (HHA–HHA, Case 2), and dissimilar HHA–RHA (Case 3) joints produced under temperature-controlled conditions (770 °C). Neutron diffraction was employed to quantify the magnitude and spatial distribution of residual stresses in the longitudinal, transverse, and normal directions and to correlate them with weld microstructure and hardness. Tensile residual stresses were concentrated in the softened HAZ, reaching approximately 300 MPa for Case 2 and 400 MPa for Case 1 (≈50–70 % of the base-metal yield strength; ∼581 MPa for RHA and ∼566 MPa for HHA), while compressive residual stresses dominated the stir zone. The spatial extent of tensile stresses scaled with the width of the softened HAZ, which was largest in the dissimilar HHA–RHA joint and smallest in the HHA–HHA joint. Full-width-at-half-maximum (FWHM) analysis revealed low microstrain in overtempered HAZ regions and high microstrain in the stir zone associated with severe plastic deformation and fresh martensite formation. This work demonstrates that residual stress evolution in FSW of martensitic armor steels is governed not primarily by peak temperature or thermal contraction, as inferred from fusion-welding analogies, but by the competition between transformation-induced volumetric expansion and tempering-induced stress relaxation. The relative dominance of these mechanisms is shown to depend on alloy hardenability and local thermal history, leading to more extensive HAZ softening and broader tensile stress regions in the lower-hardenability RHA steel. These findings establish a transferable mechanistic framework for optimizing solid-state joining strategies in high-strength steels and other transformation-hardening alloys beyond armor applications.

Friction stir welding↗
DOE OSTI2021

Urban Forests as Main Regulator of the Evaporative Cooling Effect in Cities

Abstract Higher temperatures in urban areas expose a large fraction of the human population to potentially dangerous heat stress. Green spaces are promoted worldwide as local and city‐scale cooling strategies but the amount, type, and functioning of vegetation in cities lack quantification and their interaction with urban climate in different settings remains a matter of debate. Here we use state‐of‐the‐art remote sensing data from 145 city clusters to disentangle the drivers of surface urban heat islands (SUHI) intensity and quantify urban‐rural differences in vegetation cover, species composition, and evaporative cooling. We show that nighttime SUHIs are affected mostly by abiotic factors, while daytime SUHIs are highly correlated with vegetation characteristics and the wetness of the background climate. Magnitude and seasonality of daytime SUHIs are controlled by urban‐rural differences in plant transpiration and leaf area, which explain the dependence of SUHIs on wetness conditions. Leaf area differences are caused primarily by changes in vegetation type and a loss of in‐city forested areas, highlighting the importance of maintaining “natural reserves” as a sustainable heat mitigation policy.

Paschalis, Athanasios↗
DOE OSTI2022

Frictional properties of Opalinus Clay: influence of humidity, normal stress and grain size on frictional stability

SUMMARY The Opalinus Clay (OPA) is a clay-rich formation considered as a potential host rock for radioactive waste repositories and as a caprock for carbon storage in Switzerland. Its very low permeability (10−19 to 10−21 m2) makes it a potential sealing horizon, however the presence of faults that may be activated during the lifetime of a repository project can compromise the long-term hydrological confinement, and lead to mechanical instability. Here, we have performed laboratory experiments to test the effect of relative humidity (RH), grain size (g.s.) and normal stress on rate-and-state frictional properties and stability of fault laboratory analogues corresponding to powders of OPA shaly facies. The sifted host rock powders at different grain size fractions (<63 μm and 63 < g.s. < 125 μm), at room (∼25 per cent) and 100 per cent humidity, were slid in double-direct shear configuration, under different normal stresses (5–70 MPa). We observe that peak friction, μpeak and steady-state friction, μss, depend on water vapour content and applied normal stress. Increasing relative humidity from ∼25 per cent RH (room humidity) to 100 per cent RH causes a decrease of frictional coefficient from 0.41 to 0.35. The analysis of velocity-steps in the light of rate-and-state friction framework shows that the stability parameter (a–b) is always positive (velocity-strengthening), and it increases with increasing sliding velocity and humidity. The dependence of (a–b) on slip rate is lost as normal stress increases, for each humidity condition. By monitoring the variations of the layer thickness during the velocity steps, we observe that dilation (Δh) is directly proportional to the sliding velocity, decreases with normal stress and is unaffected by humidity. Microstructural analysis shows that most of the deformation is accommodated within B-shear zones, and the increase of normal stress (σn) promotes the transition from strain localization and grain size reduction to distributed deformation on a well-developed phyllosilicate network. These results suggest that: (1) the progressive loss of velocity dependence of frictional stability parameter (a–b) at σn > 35 MPa is dictated by a transition from localized to distributed deformation and (2) water vapour content does not affect the deformation mechanisms and dilation, whereas it decreases steady-state friction (μss), and enhances fault stability.

58 GEOSCIENCES↗
DOE OSTI2023

Microstructural, Corrosion, and Mechanical Characterization of Friction Stir Welded Al 6022-to-ZEK100 Mg Joints

Friction stir welded (FSW) aluminum–magnesium lightweight vehicle joints have gained significant interest due to their high strength-to-weight ratio. In this work, the corrosion resistance of this material is analyzed through electrochemical tests, which include open circuit potential (OCP) inspection and potentiodynamic polarization (PD) scanning. Weight loss measurements tested the corrosion rate of the FSW weld through cyclic corrosion testing (CCT) according to the standard SAEJ 2334. Mechanical properties were also investigated, including lap-shear strength, micro- and nano-hardness mapping, and true stress–strain curves as a function of local processing history. The electrochemical results indicate that the center weld zone’s corrosion property stays between the two base alloys. Indentation-based testing demonstrated that the weld zone behaves differently from base alloys. Lap shear strength surprisingly did not drop much even after eight weeks of cyclic corrosion tests, indicating that the joint did not allow any ingress of the electrolyte.

36 MATERIALS SCIENCE↗
NASA NTRS1975

High-order magnetic multipoles as a source of gross asymmetry in the distant Jovian magnetosphere

The longitudinal asymmetry of the surface magnetic-field strength at Jupiter causes a longitudinal asymmetry in the equatorial plasma mass density within the Jovian magnetosphere. The rotation of these density variations with the planet causes a diurnal variation of the radial distance on the night side at which the centrifugal stress of the magnetospheric plasma exceeds the local magnetic-field tension. This is approximately the distance at which the magnetic field opens to interplanetary space; we estimate that the opening distance can vary by as much as 14% as a result of the observed surface field asymmetry. Such a diurnal variation of the boundary of the particle trapping region can account for the observed ten-hour modulation of relativistic electrons emitted from Jupiter into interplanetary space.

Dessler, A. J.↗
NASA NTRS1979

Large eddy simulation of turbulent channel flow: ILLIAC 4 calculation

The three-dimensional time dependent equations of motion were numerically integrated for fully-developed turbulent channel flow. A large scale flow field was obtained directly from the solution of these equations, and small scale field motions were simulated through an eddy viscosity model. The calculations were carried out on the ILLIAC 4 computer. The computed flow patterns show that the wall layer consists of coherent structures of low speed and high speed streaks alternating in the spanwise direction. These structures were absent in the regions away from the wall. Hot spots, small localized regions of very large turbulent shear stress, were frequently observed. The profiles of the pressure velocity-gradient correlations show a significant transfer of energy from the normal to the spanwise component of turbulent kinetic energy in the immediate neighborhood of the wall ('the splatting effect').

Kim, J.↗
NASA NTRS1981

Turbulent boundary layer over solid and porous surfaces with small roughness

The turbulent boundary layer over a smooth, solid wall is examined along with a sandpaper-roughened, solid wall, and a porous wall. Suitable results are obtained with the smooth, solid wall for the Law of the Wall, the Defect Law, and the axial and turbulence intensities. The logarithmic portion of the Wall Law is shifted in the sandpaper-roughened, solid wall and an increase in the normal turbulence intensity and Reynolds stress is observed. An increase in the local skin friction values and all the turbulence values is found with the porous wall. The influence of a slightly rough, porous wall of sintered metal on the boundary layer is compared with a solid sandpaper-roughened wall in the same nominal K(+) range.

Kong, F. Y.↗