Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “literature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Combustion characteristics of diisopropoxymethane, a low-reactivity oxymethylene ether

Oxymethylene ethers (OMEs) have been studied for use as low-sooting diesel fuel additives or substitutes; very little literature discusses OMEs as spark-ignition (SI) fuels due to their typically high cetane numbers. In this work, a lower-reactivity, branched OME, diisopropoxymethane (DIPM), is evaluated to determine its effectiveness as a spark-ignition fuel, as it is the lowest-reactivity OME (as determined by Indicated Cetane Number) thus far evaluated in the literature. DIPM is synthesized in-house via acetalization from isopropanol (iPrOH) and trioxane using standard OME production practices. DIPM was then tested in a rapid compression machine (RCM) for autoignition and spark ignition characteristics, and in a modified CFR engine to determine effective octane numbers. In the RCM, an autoignition temperature sweep was performed at stoichiometric conditions from 1000/T = 1.7 - 1.0, at 5:1 inert ratio (comparable to approximately 25% EGR), where it was found that DIPM has ignition delay times 5–10x faster than isooctane and displays NTC ignition behavior. Blends with iPrOH indicate that reactivity can be matched with isooctane with low blend ratios of iPrOH in DIPM. Flame speeds were tested with a laser spark for ignition in the RCM, where the flame speed of DIPM and isooctane is determined to be comparable at engine relevant conditions. In the CFR engine, effective RON and MON based on pressure trace frequency domain measurements were determined for DIPM and a 15 vol% iPrOH in DIPM blend. Neat DIPM has (R+M)/2 = 59 and a negative sensitivity of S = -18, consistent with its NTC behavior and higher reactivity. Furthermore the DIPM/iPrOH blend has positive sensitivity and a pump-gasoline range (R+M)/2 = 89.3. DIPM on its own is unlikely to be an effective SI fuel, however, when blended with iPrOH as an ON booster, it may be a promising SI candidate fuel.

09 BIOMASS FUELS↗
DOE OSTI2025

Temporal relationships among lunar crustal rocks

Temporal relationships among the three most common suites of lunar crustal rocks have been investigated by obtaining new high precision ages on Felsic/Alkali-suite Quartz monzodiorite Clast B from breccia 15405 and Magnesian-suite norite 78235/6/8/55/56 and comparing them to previously dated ferroan anorthosite sample 60025. The weighted average age of 4337.19 ± 0.49 Ma of 15405 Clast B is defined by zircon U-Pb and Pb-Pb ages as well as mineral isochron Sm-Nd and Nd-Nd ages. It is identical to the weighted average age for Apollo 17 norite 78235/6/8/55/56 of 4334.1 ± 3.5 Ma which is defined by Pb-Pb ages measured on baddeleyites in this investigation and less precise Pb-Pb and Sm-Nd ages reported in the literature. Both ages are ∼ 25 Ma younger than the weighted average of Sm-Nd and Pb-Pb ages reported in the literature on ferroan anorthosite 60025 of 4359.3 ± 2.3 Ma. The fact that ages of all three samples are defined by multiple U-Pb, Pb-Pb, Sm-Nd, and 142 Nd- 143 Nd chronometers provide confidence that they record the igneous crystallization history of the samples and do not represent disturbances or mixing lines with no temporal significance. Here, the extent to which these three ages represent broader scale magmatism is difficult to evaluate. Nevertheless, the age defined for 15405 Clast B, 78235/6/8/55/56, and 60025 are contemporaneous with the peak of ages observed in detrital zircons from the Apollo 12, 14, 15, and 17 landing sites (4340 ± 20 Ma), a Mg-suite Sm-Nd whole rock isochron defined by samples from Apollo 14, 15, 16, and 17 landing sites (4348 ± 25 Ma), and a Ferroan Anorthosite-suite Sm-Nd whole rock isochron defined by samples from the Apollo 15 and 16 landing sites (4354 ± 29 Ma). This implies that Ferroan Anorthosite-suite magmatism is temporally distinct and earlier than magmatism associated with the Mg-suite and the Felsic/Alkali-suite, as predicted by the lunar magma ocean model of lunar differentiation. The short 35 ± 10 Ma interval between primary ferroan anorthosite magmatism and secondary magmatism suggests that the lunar crust formed over a limited period of time. Although heat from decay of long-lived isotopes, large impacts, tidal heating associated with interactions between the Earth and Moon, and density driven overturn of the magma ocean have all been invoked to explain production of ancient secondary crustal magmatism, only tidal heating and cumulate overturn are consistent with the apparent short duration of secondary crustal magmatism and the great depth of crystallization implied for some Mg-suite samples. The initial ε 143 Nd values derived from the 15405 Clast B and 78238 Mg-suite norite isochrons, as well as a Mg-suite whole rock isochron are −0.23 ± 0.11, −0.27 ± 0.74, and −0.25 ± 0.09, respectively. They are identical within uncertainty indicating that Mg-suite and Felsic/Alkali-suite magmas were derived from materials that had the same time averaged Sm/Nd ratios since the formation of the solar system. This, combined with the contemporaneous nature of 15405 Clast B and 78235/6/8/55/56 Mg-suite norite, is consistent with evolution of both samples, and likely both magma suites, from a common source through closed system fractional crystallization or partial melting processes.

Chronology↗
DOE OSTI2023

On falling film evaporator – A review of mechanisms and critical assessment of correlation on a horizontal tube bundle with updated development

Optimization of the energy efficiency and reduction of the greenhouse gas emission for the heat pump system is imperative to meet the net-zero goals at 2050. Chillers with falling film evaporator design not only possess better system performance but also contain less refrigerant inventory. Hence, accurate prediction of the evaporator performance is pivotal especially when charged with low-GWP refrigerant. Here, the study reviews the correlations for falling film evaporator with a horizontal tube bundle configuration. The major efforts of this study include four tasks: (a) literature review of the experimental studies and available empirical correlations; (b) comprehensive discussion of the falling film evaporation heat transfer mechanism; (c) development of a new rationally based correlation based on available literature; and (d) comparison of different correlations based on the existing data. The collected data includes 4114 data points from 8 sources, 6 refrigerants (R-600a, R-290, R-245fa, R-134a, R-1234ze(E), R-123), 5 types of the tubes (Plain, Turbo-GII-HP, GEWA-B, Low-fin, High-Flux), liquid Weber number from 2.2 × 10 –6 to 0.7, imposed vapor Weber number from 0 to 37.2, heat flux from 2.5 to 151.5 kW/m 2 , and film Reynolds number from 1 to 3159.8. The new correlation gives a MAD of 28.3%, and an R 2 of 0.86. Yet, the developed correlation considers various heat transfer mechanisms, including the transition point from falling film evaporation to the nucleate boiling, local evaporation, dry-out, mist flow, imposed flow, and enhanced tube effects.

42 ENGINEERING↗
DOE OSTI2022

Design and performance of a variable gap system for thermal conductivity measurements of high temperature, corrosive, and reactive fluids

We report high-temperature fluids such as molten salts, liquid metals, and gasses are being proposed for many advanced energy systems including thermal energy storage devices, concentrating solar plants, and advanced nuclear reactor designs. However, the chemical behavior and thermophysical properties of many of these fluids have not been well characterized, which hinders the design, modeling, safety analysis, and deployment of these systems. Thermal conductivity is a property that is especially limited by existing measurement capabilities, which are subject to errors caused by convection, material interaction, radiative heat transfer, and instrument degradation. Therefore, there is a lack of standard, systematic measurement techniques for high-temperature, reactive, and corrosive fluids. In this work, the development of a variable gap thermal conductivity measurement system is detailed. The system is designed to measure the thermal conductivity of highly corrosive and reactive fluids, and survive operation between 100 °C and 800 °C. The effects of convection are minimized by limiting the thickness of the specimen to thin sizes (<0.3 mm). Corrections for radiative heat transfer were included in the working equations to consider specimens with varying optical properties. The design, construction, instrumentation, operating principles, and data analysis techniques are discussed in detail. The system was tested up to 500 °C using helium gas and molten KNO 3 -NaNO 3 to verify the measurement technique and determine the sources of error. At 300 and 400 °C KNO 3 -NaNO 3 , results showed maximum relative error of 6% when compared to results in the literature. The helium results were within 13% of those in the literature at 300 and 400 °C. Higher errors were observed at 500 °C for both fluids, and the sources of these errors are discussed.

42 ENGINEERING↗
DOE OSTI2023

Thermal conductivity measurement using modulated photothermal radiometry for nitrate and chloride molten salts

Molten salts are being used or explored for thermal energy storage and conversion systems in concentrating solar power and nuclear power plants. Thermal conductivity of molten salts is an important thermophysical property dictating the performance and cost of these systems, but its accurate measurement has been challenging, as evidenced by wide scattering of existing data in literature. The corrosive and conducting nature of these fluids also leads to time consuming sample preparation processes of many contact-based measurements. Here, in this work, we report the measurement of thermal conductivity of molten salts using a modulated photothermal radiometry (MPR) technique, which is a laser-based, non-contact, frequency-domain method adopted for molten salts for the first time. By unitizing the advantages of front side sensing of frequency-domain measurements and the vertical holder orientation, the technique can minimize the natural convection and salt creeping effects, thus yielding accurate molten salt thermal conductivity . The MPR technique is first calibrated using standard molten materials including paraffin wax and sulfur. It is then applied on measuring pure nitrate salts (NaNO 3 and KNO 3 ), solar salt (NaNO 3 –KNO 3 mixture), and chloride salt (NaCl–KCl–MgCl 2 ). The measurement results are compared with data from literature, especially those obtained from laser flash analysis (LFA). Our results demonstrate that the MPR is a convenient and reliable technique of measuring thermal conductivity of molten salts. Accurate thermal conductivity data of molten salts will be valuable in developing the next-generation high-temperature thermal energy storage and conversion systems.

14 SOLAR ENERGY↗
DOE OSTI2024

Alternating conduction and convection drying of paper – an experimental analysis with a continuous data acquisition approach

In conventional multi-cylinder drying of paper and board, both conductive drying from steam-heated dryer cylinders and convective drying by flowing air over the paper surface in the pockets are used. Conductive drying from steam-heated drying cylinders is a critical component in providing the necessary thermal energy to paper and board as they dry. Steam temperature and internal and external resistances at the contacting surface are critical process parameters influencing the conductive drying process. An experimental setup was developed to study the alternating conductive and convective drying of paper and board. Paper sheet moisture, temperature, and temperature distribution within the heated platen and the instantaneous heat flux as the sheet was being dried were measured. The instantaneous heat flux, contact heat transfer coefficient, and drying rates were determined as drying proceeds. Experimental results, as well as comparisons to literature and commercial data, are presented. The conductive heat transfer coefficients determined were compared to traditional correlations normally used in the modeling of paper drying. Similarly, the convective heat and mass transfer coefficients are also determined and compared to literature data. In addition to the evaluation of alternating conductive and convective drying characteristics of paper and board, the potential inclusion of auxiliary energy components will also be included. Experimental results from the conduction and convection drying system are presented. Furthermore, this data will be useful in process development, intensification of manufacturing processes, and modeling and simulation of paper drying processes.

42 ENGINEERING↗
DOE OSTI2020

Equilibrium vapor pressure properties for absorbent and adsorbent materials

Sorption devices are important tools for the efficient utilization of fuels and waste heat. Amid a tremendous diversity of cycles and applications, all sorption systems have an equilibrium vapor pressure that depends on the sorbent temperature and composition. The vapor pressure properties of working fluids are reported in the literature in a variety of ways, which impedes wide-ranging cross comparisons or screening studies for novel applications. This work compiles equilibrium vapor pressure properties for 123 liquid absorbents with 31 absorbates and 139 solid adsorbents with 16 adsorbates. The adsorption pairs are represented with six functional forms. Additionally, most of the absorption pairs are represented with 10 functional forms, plus several that are represented with custom empirical equations. Because the functional forms used in the literature vary widely, in this work each functional form was generalized. This paper is designed to facilitate comparisons of working fluid properties for screening studies, provide a quick reference to existing research, and present a framework for standardizing the reportage of vapor pressure equilibrium data for existing and future working pairs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Spark plasma sintered, MoNbTi-based multi-principal element alloys with Cr, V, and Zr

MoNbTi, MoNbTiZr, CrMoNbTiZr, and MoNbTiVZr multi-principal element alloys (MPEAs) were fabricated via spark plasma sintering (SPS) and investigated for use in high-strength applications. The fabrication method by SPS and powder metallurgy differs from those presented in the prior literature, where most MPEAs are fabricated using arc melting (AM) methods. Here cryogenic milling was used to maximize potential defect sinks (grain boundaries) for radiation resistance and to increase ultimate tensile strength through the Hall-Petch effect. SPS was chosen for consolidation in order to maintain a fine-grained structure during densification. Each alloy was characterized using x-ray diffraction and scanning electron microscopy for phase identification and compositional homogeneity. The base ternary alloy MoNbTi presented a predominantly single BCC system with minor cubic phases. The introduction of additional alloying elements—Zr, V, and Cr—heightened the phase complexity and increased the fractions of a secondary BCC phase and an HCP phase from Zr. The addition of Cr induced a larger fraction of the Laves phase to form. The addition of V caused the precipitation of small Mo inclusions. Thermodynamic analysis was performed to understand the separation of phases in each alloy. Discrepancies among the phase predictions generated by thermodynamic models, phases previously presented in the literature, and the characterization results suggest that MPEA fabrication methods, especially solid-state methods, require significant investigation to ensure that alloys can remain stable throughout their anticipated service lifetimes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Passive and active peer effects in the spatial diffusion of residential solar panels: A case study of the Las Vegas Valley

This research analyzes the role of peer influences on the adoption of residential rooftop solar photovoltaic panels (PV) within the context of the Diffusion of Innovation Theory. PV literature indicates that adopters are influenced by word of mouth (WOM) information exchange with peers, i.e., active peer effects, while other studies suggest that living near households with visible rooftop PV installations influences adoption, i.e., passive peer effects. We bridge the gap in this literature by conducting a mixed methods analysis. We develop and administer a survey to Las Vegas Valley (LVV) residents to identify current and potential PV adopters' perceptions of peer-effects and consumer intention variables. We conduct a spatial analysis of Google's Project Sunroof data to identify LVV neighborhoods in the later stages of the PV diffusion process, i.e., those with the highest PV adoption rates. Key results show that current PV adopters living in early diffusion areas report significantly higher active and passive peer effects compared to adopters in later diffusion areas. Potential adopters in later diffusion areas report higher passive peer effects than those in early diffusion areas. Overall, because LVV has a low PV adoption rate (<3%), short term strategies aimed at increasing PV adoption should emphasize WOM active peer effects. Here, we caution against long-term green marketing strategies focusing solely on peer-effects as the PV market matures.

14 SOLAR ENERGY↗
DOE OSTI2025

Local conservation of energy in fully implicit PIC algorithms

We consider the issue of strict, fully discrete local energy conservation for a whole class of fully implicit local-charge- and global-energy-conserving particle-in-cell (PIC) algorithms. Earlier studies demonstrated these algorithms feature strict global energy conservation. However, whether a local energy conservation theorem exists (in which the local energy update is governed by a flux balance equation at every mesh cell) for these schemes is unclear. In this study, we show that a local energy conservation theorem indeed exists. We begin our analysis with the 1D electrostatic PIC model without orbit-averaging, and then generalize our conclusions to account for orbit averaging, multiple dimensions, and electromagnetic models (Darwin). In all cases, a temporally, spatially, and particle-discrete local energy conservation theorem is shown to exist, proving that these formulations (as originally proposed in the literature), in addition to being locally charge conserving and globally energy conserving, are strictly locally energy conserving as well. In contrast to earlier proofs of local conservation in the literature, which only considered continuum time, our result is valid for the fully implicit time-discrete version of all models considered, including important features such as orbit averaging. We demonstrate the local-energy-conservation property numerically with a paradigmatic numerical example.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

The lay of the land: What we know about non-operating agricultural and absentee forest landowners in the U.S. and Europe

While non-operating agricultural and absentee forest landowners across the U.S. and Europe are an important group of landowners, our understanding of them remains relatively limited. In this paper, we conduct a systematic literature review on these landowners to encapsulate a current lay of the land in terms of what we know about these landowners and move the dialogue on this topic forward. Eighty-one articles are identified in our search of empirical literature. For each of the landowner types, we discuss their demographics and the three primary themes that emerged related to land management: participation in land management decisions, attitudes regarding land use and ownership, and resource needs in working with these landowners. For agricultural non-operating landowners, we find limited participation in land management decisions, particularly among women, a variety of individual and social factors play a role in involvement, and while they have pro-conservation attitudes, implementation of conservation practices is more limited. Absentee forest landowners we find are more willing to use management plans, yet less willing to engage in active management and risk reduction. These landowners have a range of attitudes regarding land use, with studies highlighting recreation, conservation, and profit motivations. In conclusion, our review concludes with identifying specific needs for more research and outreach on these landowners.

absentee↗
DOE OSTI2020

Grand potential sintering simulations of doped UO 2 accident-tolerant fuel concepts

Chromium-doped UO is a widely-studied near-term deployable accident-tolerant fuel concept because it results in a dense, large-grain structure that increases the fuel resistance to densification, swelling, and fission gas release. A new charged-interstitial mechanism was recently proposed to describe the behavior of dopants like chromium in sintered UO 2 . Based on that mechanism, manganese was suggested as an even stronger dopant than chromium. In the current work we use mesoscale sintering simulations in an effort to validate the new mechanism. We compare the relative behavior of Cr-doped and undoped UO 2 against experimental data in the literature. We also make predictions of the relative behavior of Mn-doped UO 2 . Simulations are done using the phase field-based grand potential sintering model. Dopants have two effects on sintered UO 2 . They marginally increase the densification rate and greatly increase the average grain size. Both of these effects are individually tested in small-scale simulations. Then large 3D sintering simulations are used to test the combined behavior of both effects. The results for the densification rate simulations are consistent with experiments for Cr-doped fuels. However, we note the grain growth rates are lower than what is found in the literature for Cr-doped fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Helium causing disappearance of a/2<111> dislocation loops in binary Fe-Cr ferritic alloys

In this work, single and dual-beam self-ion irradiations were performed at 500°C on ultra-high purity Fe14%Cr alloy to ~0.33 displacements-per-atom (dpa), and 0 or 3030 atomic-parts-per-million (appm) helium/dpa, respectively. Using transmission electron microscopy, we reveal that helium can drastically modify the dislocation loop Burgers vector in Fe-Cr alloys. Helium co-implantation caused complete disappearance of a/2<111> type dislocation loops, and the microstructure consisted of only a<100> loops. Conversely, a/2<111> type loops were predominant without He co-implantation. The total loop density remained largely unaffected. The results strikingly contrast literature asserting that helium stabilizes a/2<111> type loops in bcc Fe alloys, based on low temperature irradiations. Collectively analyzing the results with literature suggest that the small positive interaction between helium and self-interstitial atoms (SIA) in Fe predicted by atomistic simulations maybe insufficient to holistically explain the dislocation loop microstructure development in presence of helium. Helium-SIA positive binding inadvertently implies elevated a/2<111> loop fraction and higher loop densities that the present results contradict. Helium induced high cavity density causing a preferential loss of highly glissile <111> clusters, leaving the matrix saturated with <100> type clusters is proposed as a potential mechanism. Further, the in-situ irradiations combined with Burgers vector analysis strengthened the evidence of Cr-induced dislocation loop mobility reduction that appears to stabilize the a/2<111> type loops and causes higher loop densities in Fe-Cr alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

An ab initio molecular dynamics investigation of the thermophysical properties of molten NaCl-MgCl 2

Molten salts have many applications in the nuclear and solar energy industries for thermal storage and heat transfer applications. However, there is a knowledge gap in molten salt thermophysical properties which hinders the technical readiness level of molten salt applications, especially in the nuclear industry. A common method of investigating new materials is through ab initio Molecular Dynamics (AIMD) simulations which is an effective tool to investigate structural and thermophysical properties at realistic temperatures. NaCl-MgCl 2 is an inexpensive salt that is a good candidate for use as a heat transfer medium in solar power applications or in the secondary loop of a nuclear reactor. In this article, the thermophysical properties of NaCl-MgCl 2 are computed via AIMD calculations to supplement the limited experimental studies in the literature. Here a wide range of compositions and temperatures for the pseudo-binary NaCl-MgCl 2 were used to calculate the density, heat capacity, compressibility, enthalpy of mixing, and volumetric thermal expansion coefficient. AIMD is shown to accurately model the densities of molten NaCl-MgCl 2 as there is good agreement with the available literature. This work observed a transition to a monotonic increase of the density with respect to MgCl 2 composition occurring above 1100 K. The heat capacity values increase uniformly with respect to concentration of MgCl 2 at a rate of 2.85 J/mol-K per 10 mol% of MgCl 2 . Select thermophysical properties are fit to a Redlich-Kister expansion for utilization in multiphysics simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Determining the effects of U/Pu ratio on subsolidus phase transitions in U-Pu-Zr metallic fuel alloys

Here, ternary alloys consisting primarily of uranium, plutonium, and zirconium (U-Pu-Zr) are among the leading candidate fuel systems considered for fast spectrum nuclear reactors. Despite historical operation data from the testing of U-Pu-Zr rods in the Experimental Breeder Reactor-II, considerable uncertainty about the evolution of phases and microstructure across the ternary composition space exists. Due to sluggish kinetics and other difficulties in handling metal actinide specimens, quantitative measurements of phase-transitions in U-Pu-Zr alloys remain sparse in scientific literature, with most investigators reporting either phase-transition temperatures or phase identification data, but not both from the same specimens. The purpose of this paper is to critically compare experimental and calculated phase transition data and correlate with the microstructure and phase characterization data of as-cast and annealed U-Pu-Zr alloys. Phase transition peaks were measured using differential scanning calorimetry in the subsolidus regions (723-948 K) of three ternary U-Pu-Zr alloys with the same zirconium concentration but various U/Pu ratios. Overlapping peaks were deconvoluted using a Frazier-Suzuki peak fitting algorithm, and the critical peak temperatures and enthalpies were calculated. In general, increasing concentrations of Pu were associated with enhanced thermal stability of the body-centered cubic γ phase upon both heating and cooling. Experimental phase transition temperatures in this study tended to agree well with the predictions of the established ternary phase diagrams and other reported phase transition temperatures in literature. Additionally, the TAF-ID thermodynamic database was used to calculate a U-Pu-40 at.% Zr pseudobinary diagram as well as ternary diagrams from 773 to 973 K. The equilibrium phase transition temperatures tended to be considerably lower than measured peak temperatures upon both heating and cooling. Recommendations for improving the quality of data in future U-Pu-Zr characterization studies are also discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

New insights on the effects of chemistry and temperature on α’ precipitation during aging of FeCrAl alloys

Here, the effect of Al on α' precipitation in FeCrAl alloys was studied through thermal aging of several model binary FeCr and FeCrAl alloys with Cr content of 13 wt.%, 17 wt.%, and 25 wt.% with and without 5.5 wt.% Al. Aging was performed up to 1,000h at varying temperatures from 400-500°C. At 400°C no age hardening was observed due to slow kinetics at this temperature. For both the 17Cr and 25Cr alloys, the addition of Al shows a lowering of the miscibility gap, consistent with other reports in literature. Interestingly, however, for the 25Cr alloys the addition of Al in the FeCrAl ternary alloy accelerated α' precipitation below the miscibility gap. Such enhanced precipitation has also been predicted by our atomistic kinetic Monte Carlo (AKMC) simulations. While previous literature has often focused on Al suppressing α', here we show that while Al can lower the miscibility gap in the Fe-Cr ferritic system thermodynamically, it may also enhance the kinetics of precipitation.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Sintering effects on NpO 2 grain size and morphology: The role of precursor Np phase

Neptunium dioxide (NpO 2 ) is a key phase in nuclear material processing as a target material for the production of plutonium-238 ( 238 Pu) and has been historically synthesized via the calcination of a Np oxalate precursor. Alternative synthesis methods for NpO 2 are now more prevalent, necessitating their study and comparison with the more common oxalate route. The purpose of this work was to investigate the microstructural properties of NpO 2 synthesized from a nitrate-based Np precursor phase via the assessment of NpO 2 particle size and morphology as a function of calcination temperature and time. Scanning electron microscopy (SEM) was used to probe the primary grain size and morphology of NpO 2 after calcination at temperatures ranging from 700 to 1100 °C and hold times ranging from 1 to 10 h. Post-image analysis using ImageJ software enabled the quantification of mean particle diameter. This analysis indicated that particle diameter increases with both increasing calcination temperature and hold time. Primary particles were shown to be clumped in irregular patterns into the overall rough, blocky aggregates, but this macroscopic morphology was not affected by calcination time or temperature. Although trends in primary grain size of NpO 2 were consistent with available literature from other Np precursor phases, the macroscopic morphology of the NpO 2 aggregates was quite different than reported for other precursors. Through comparison with historical literature on Np oxalate, this work emphasizes the importance of Np precursor on the physical properties of NpO 2 .

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2021

Modelica-based system modeling for studying control-related faults in chiller plants and boiler plants serving large office buildings

System modeling is critical when studying operation faults in chiller plants and boiler plants. However, current fault models have difficulties faithfully representing the operation of chiller plants and boiler plants under the effects of those faults, especially the control-related ones. In this study, we present a systematic method to develop high-fidelity models for approximating the behaviors of chiller plants and boiler plants under faulty conditions. Compared to existing ones, the resulting fault models have two advantages: first, they better characterize the dynamic patterns in the system operation. In those models, control architecture and control logic are faithfully implemented. Thus, they can be used to study control-related faults, such as incorrect staging control due to sensor bias and mistuned feedback control. Second, they are readily extensible and can support large-scale investigations to explore different faulty conditions/scenarios. Those models are established in a hierarchical structure while modules in each layer can be redeclared and parameterized at upper layers. In such a case, modifications to the models can be realized through model modifiers and the process can be easily streamlined with scripts. We applied the proposed models in a comprehensive fault impact evaluation of the 13 control-related faults of chiller and boiler plants. In this evaluation, the proposed plant model is coupled with the EnergyPlus thermal load model to study the impact of various faulty scenarios. Based on the evaluation results, we identified the faults that have the most significant impacts on the operation of the chiller and boiler plants, respectively. We also found that the relationship between the impacts of the studied faults and the severity level of the faults are highly non-linear

Huang, Sen↗