Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “joint”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Compliant Intramedullary Stems for Joint Reconstruction

The longevity of current joint replacements is limited by aseptic loosening, which is the primary cause of non-infectious failure for hip, knee, and ankle arthroplasty. Aseptic loosening is typically caused either by osteolysis from particulate wear, or by high shear stresses at the bone-implant interface from over-constraint. Our objective was to demonstrate feasibility of a compliant intramedullary stem that eliminates over-constraint without generating particulate wear. The compliant stem is built around a compliant mechanism that permits rotation about a single axis. We first established several models to understand the relationship between mechanism geometry and implant performance under a given angular displacement and compressive load. We then used a neural network to identify a design space of geometries that would support an expected 100-year fatigue life inside the body. We additively manufactured one representative mechanism for each of three anatomic locations, and evaluated these prototypes on a KR-210 robot. The neural network predicts maximum stress and torsional stiffness with 2.69% and 4.08% error respectively, relative to finite element analysis data. We identified feasible design spaces for all three of the anatomic locations. Simulated peak stresses for the three stem prototypes were below the fatigue limit. Benchtop performance of all three prototypes was within design specifications. Our results demonstrate the feasibility of designing patient- and joint-specific compliant stems that address the root causes of aseptic loosening. Guided by these results, we expect the use of compliant intramedullary stems in joint reconstruction technology to increase implant lifetime.

60 APPLIED LIFE SCIENCES↗

Joint Expansion Planning of Power and Water Distribution Networks

This research considers the joint expansion planning of power and water distribution networks, which are interdependent at various levels. We consider the dependency arising through the power consumption of pumps and develop models for integrating new components into existing networks. Then, we formulate the joint expansion planning as a Mixed Integer Nonlinear Program (MINLP). Applying this MINLP to a small-scale test network, we illustrate the advantages offered by joint expansion planning, such as increased flexibility and reduced costs and redundancy, over independently expanding power and water distribution networks.

expansion planning↗

Joint Sparsity Pattern Recovery With 1-b Compressive Sensing in Distributed Sensor Networks

In this paper, we study the problem of joint sparse support recovery with 1-b quantized compressive measurements in a distributed sensor network. Multiple nodes in the network are assumed to observe sparse signals having the same but unknown sparse support. Each node quantizes its measurement vector element-wise to 1 b. First, we consider that all the quantized measurements are available at a central fusion center. We derive performance bounds for sparsity pattern recovery using 1-bit quantized measurements from multiple sensors when the maximum likelihood decoder is employed. We further develop two computationally tractable algorithms for joint sparse support recovery in the centralized setting. One algorithm minimizes a cost function defined as the sum of the likelihood function and the l-∝ quasi-norm, while the other algorithm extends the binary iterative hard thresholding algorithm to the multiple measurement vector case. Second, we consider a decentralized setting where each node transmits 1-b measurements to its one-hop neighbors. The basic idea behind the algorithms developed in the decentralized setting is to embed collaboration among nodes and fusion strategies. We show that even with noisy 1-b compressed measurements, joint support recovery can be carried out accurately in both centralized and decentralized settings. Additionally, we further show that the performance of the proposed 1-bit compressive sensing-based algorithms is very close to that of their real-valued counterparts except when the signal-to-noise ratio is very small.

97 MATHEMATICS AND COMPUTING↗

Joint Estimation of Behind-the-Meter Solar Generation in a Community

Distribution grid planning, control, and optimization require accurate estimation of solar photovoltaic (PV) generation and electric load in the system. Most of the small residential solar PV systems are installed behind-the-meter making only the net load readings available to the utilities. This paper presents an unsupervised framework for joint disaggregation of the net load readings of a group of customers into the solar PV generation and electric load. Our algorithm synergistically combines a physical PV system performance model for individual solar PV generation estimation with a statistical model for joint load estimation. The electric loads for a group of customers are estimated jointly by a mixed hidden Markov model (MHMM) which enables modeling the general load consumption behavior present in all customers while acknowledging the individual differences. At the same time, the model can capture the change in load patterns over a time period by the hidden Markov states. The proposed algorithm is also capable of estimating the key technical parameters of the solar PV systems. Our proposed method is evaluated using the net load, electric load, and solar PV generation data gathered from residential customers located in Austin, Texas. Testing results show that our proposed method reduces the mean squared error of state-of-the-art net-load disaggregation algorithms by 67%.

behind-the-meter solar generation↗

3D Deep Learning Joint Inversion of Active Seismic Full Waveform and Passive Seismic Traveltime Data for Reservoir Imaging and Uncertainty Quantification

Here, we present deep learning (DL) networks for three-dimensional (3D) joint inversion of active seismic full waveform and passive seismic traveltime data to image reservoirs and their properties and quantify imaging uncertainties. Active seismic full-waveform data can provide high-resolution monitoring images but are collected only intermittently because of their high acquisition cost. In contrast, passive seismic data can be gathered at relatively low cost between regular active surveys, although their imaging quality can be compromised by factors such as low signal-to-noise ratios and limited ray coverage of the target. Although these datasets are routinely acquired together at CO 2 storage sites, their combined inversion within a 3D DL framework has not been previously demonstrated. To our knowledge, this is the first study to address this gap, combining the strength of both data types. For efficient data storage and DL training with large 3D seismic datasets, we use a 3D data matrix in which a random number of passive seismic traveltime data are stored as parabolic envelopes using one-hot encoding and a 3D full-waveform data matrix in which multiple shot gathers are summed. Two network architectures are evaluated: a single-encoder U-Net for single-data type inversion and a dual-encoder U-Net for joint inversion of active and passive seismic data. We also evaluate the single-encoder U-Net for joint inversion by concatenating full-waveform data and traveltime data. We propose a systematic approach for selecting an optimal dropout rate that balances regularization during training and Monte Carlo dropout-based uncertainty quantification during prediction by examining the correlation coefficient between standard deviation and prediction error, along with the training misfit, across a range of dropout rates. 3D DL inversion experiments include five different network configurations, with evaluations under ideal, noisy and dropout-enabled conditions. Both model and data uncertainties are assessed, as well as their combined effects. Across all conditions, the networks consistently predict accurate CO 2 saturation models with low prediction errors, such as a structural similarity index of 0.993 and CO 2 difference of 1.1%. Uncertainty estimates show strong spatial correlation with prediction errors, confirming the effectiveness of the proposed dropout selection approach. The results demonstrate that our DL approach, utilizing compact data representations and appropriate uncertainty quantification, yields accurate subsurface images under various inversion conditions and provides valuable insights into the reliability of predictions.

Um, Evan Schankee [Lawrence Berkeley National Labo↗

Equivalent Properties of Interfacial Void Defects at the CFRTP-adhesive Interface and Their Detrimental Effects on the Bonding Performance of Metal-CFRTP Dissimilar Joints

This paper revealed the detrimental effects of micro-scale air interfacial voids on the debonding at the interface of carbon-fiber-reinforced polyphthalamide (CFRPPA) and thermoset adhesive, representing a weak adherend-adhesive interface, within a dissimilar joint made of an aluminum alloy and a CFRPPA. The reduced lap shear strength of the joint, due to different void area fractions at the CFRPPA-adhesive interface, can be computationally described by using equivalent interfacial properties in the modeling to avoid the explicit modeling of the micro-scale interfacial voids. Such equivalent interfacial properties (e.g., interfacial normal strength, etc.) was found to have a non-linear relationship with respect to interfacial void area fraction as well as lap shear strength. This work has practical applications by utilizing equivalent interfacial properties for the analytical and/or computational design(s) of adhesively bonded joints.

Qiao, Yao↗

Exploring Failure of Adhesively-Bonded Joints with Different Void Sizes at the Same Void Volume Fraction through A Micro-scale Numerical Modeling

This paper studied the effects of void sizes on the failure behavior of adhesively-bonded materials under global shear via micro-scale computational modeling. The numerical results indicate that large void sizes with increased distances between them at the same void volume fraction can alleviate the reduced joint strength of a weaker adherend-adhesive interface caused by interfacial voids. However, this is not the case for an adherend-adhesive interface with the interfacial tensile strength being sufficiently higher than the adhesive strength, showing the negligible effect on the joint strength due to various void sizes and the amount of interfacial voids. This preliminary investigation provides insightful information for scaling up the void size in the macro-scale computational modeling of joints, and enhances the understanding of the micro-mechanical adhesion in adherend-adhesive interfaces with different levels of bonding.

Qiao, Yao↗

SU-D-201-02: Prediction of Delivered Dose Based On a Joint Histogram of CT and FDG PET Images

Purpose: To investigate whether pre-treatment images can be used in predicting microsphere distribution in tumors. When intra-arterial radioembolization using Y90 microspheres was performed, the microspheres were often delivered non-uniformly within the tumor, which could lead to an inefficient therapy. Therefore, it is important to estimate the distribution of microspheres. Methods: Early arterial phase CT and FDG PET images were acquired for patients with primary liver cancer prior to radioembolization (RE) using Y90 microspheres. Tumor volume was delineated on CT images and fused with FDG PET images. From each voxel (3.9×3.9×3.3 mm3) in the tumor, the Hounsfield unit (HU) from the CT and SUV values from the FDG PET were harvested. We binned both HU and SUV into 11 bins and then calculated a normalized joint-histogram in an 11×11 array.Patients also underwent a post-treatment Y90 PET imaging. Radiation dose for the tumor was estimated using convolution of the Y90 distribution with a dose-point kernel. We also calculated a fraction of the tumor volume that received a radiation dose great than 100Gy. Results: Averaged over 40 patients, 55% of tumor volume received a dose greater than 100Gy (range : 1.1 – 100%). The width of the joint histogram was narrower for patients with a high dose. For patients with a low dose, the width was wider and a larger fraction of tumor volume had low HU. Conclusion: We have shown the pattern of joint histogram of the HU and SUV depends on delivered dose. The patterns can predict the efficacy of uniform intra-arterial delivery of Y90 microspheres.

60 APPLIED LIFE SCIENCES↗

A Superconducting Joint for 2G HTS Tapes

An approach of the epitaxial jointing of the GdBa{sub 2}Cu{sub 3}O{sub 7 – δ}-based tapes using the YBa{sub 2}Cu{sub 3}O{sub 7 – δ} layer is proposed. The structural and electrical characteristics of the formed joint have been investigated. Using the scanning transmission electron microscopy, the cross section of the joined region has been studied, partial melting of the YBa{sub 2}Cu{sub 3}O{sub 7 – δ} layer has been observed, and the solid-phase diffusion with the formation of the (Gd, Y)Ba{sub 2}Cu{sub 3}O{sub 7 – δ}, Y{sub 2}BaCuO{sub 5}, BaCuO{sub 2}, and CuO phases has been established. It is shown that the current-carrying capability of the superconducting joint is over 30% of the initial tape current.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dual Atmosphere Isothermal Aging and Rapid Thermal Cycling of Ag-Ni and Ag-CuO Stainless Steel to Zirconia Braze Joints

Silver—copper oxide brazes are commonly used to bond zirconia to stainless steel (SS) for Solid Oxide Fuel Cell (SOFC) and other high temperature joining applications. In fact, conventional Ag-CuO compositions (where Cu segregates to the surface, oxidizes, and reduces the silver wetting angle on zirconia from ~85 to ~40°) allow brazing to be performed in air. Unfortunately, the relatively high ~40° wetting angles of these reactive air brazes, and the ability of SOFC anode gases to reduce the CuO in them, produce pores during SOFC manufacturing and operation that reduce joint strength, impermeability, and longevity. Recently, Ag brazes utilizing transient porous nickel layers, instead of CuO additions, have been shown to produce high quality braze joints between SS and yttria stabilized zirconia (YSZ). Here, the microstructural and compositional evolution of SS|Ag-3CuO|YSZ and SS|Ag-Ni|YSZ braze joints exposed to air on one side and humidified 4%H 2 -96%N 2 on the other side for either ~300 hours of ~750°C aging or ~300 25°C/min 35–830°C rapid thermal cycles are compared. While both brazes display considerable microstructural and compositional evolution, only the Ag-Ni brazes remain pore free and well bonded, indicating that Ag-Ni brazes may be more suitable for long term SOFC operation.

25 ENERGY STORAGE↗

Evaluation of subsurface damage in concrete deck joints using impact echo method

Many factors can affect the overall performance and longevity of highway bridges, including the integrity of their deck joints. This study focuses on the evaluation of subsurface damage in deteriorated concrete deck joints, which includes the delamination and corrosion of the reinforcement. Impact echo and surface wave technology, mainly a portable seismic property analyzer (PSPA), were employed to evaluate the structural deficiency of concrete joints. Laboratory tests of core samples were conducted to verify the nondestructive test results. As a result, the primary advantage of the PSPA as a bridge assessment tool lies in its ability to assess the concrete’s modulus and to detect subsurface defects at a particular point simultaneously.

42 ENGINEERING↗

Impact of tool wear on joint strength in friction stir spot welding of DP 980 steel

Friction stir spot welding has been shown to be a viable method of joining ultra high strength steel (UHSS), both in terms of joint strength and process cycle time. However, the cost of tooling must be reasonable in order for this method to be adopted as an industrial process. Recently a new tool alloy has been developed, using a blend of PCBN and tungsten rhenium (W-Re) in order to improve the toughness of the tool. Wear testing results are presented for two of these alloys: one with a composition of 60% PCBN and 40% W-Re, and one with 70% PCBN and 30% W-Re. The sheet material used for all wear testing was 1.4 mm DP 980. Lap shear testing was used to show the relationship between tool wear and joint strength. The Q70 tool provided the best combination of wear resistance and joint strength.

36 MATERIALS SCIENCE↗

Sensitivity of joint contagiousness and susceptibility-based dynamic optimal control strategies for HIV prevention

Predicting the population-level effects of an infectious disease intervention that incorporate multiple modes of intervention is complicated by the joint non-linear dynamics of both infection transmission and the intervention itself. In this paper, we consider the sensitivity of Dynamic Optimal Control Profiles (DOCPs) for the optimal joint investment in both a contagiousness and susceptibility-based control of HIV to bio-behavioral, economic, and programmatic assumptions. The DOCP is calculated using recently developed numerical algorithms that allow controls to be represented by a set of piecewise constant functions that maintain a constant yearly budget. Our transmission model assumes multiple stages of HIV infection corresponding to acute and chronic infection and both within- and between-individual behavioral heterogeneity. We parameterize a baseline scenario from a longitudinal study of sexual behavior in MSM and consider sensitivity of the DOCPs to deviations from that baseline scenario. In the baseline scenario, the primary determinant of the dominant control were programmatic factors, regardless of budget. In sensitivity analyses, the qualitative aspects of the optimal control policy were often robust to significant deviation in assumptions regarding transmission dynamics. In addition, we found several conditions in which long-term joint investment in both interventions was optimal. Our results suggest that modeling in the service of decision support for intervention design can improve population-level effects of a limited set of economic resources. We found that economic and programmatic factors were as important as the inherent transmission dynamics in determining population-level intervention effects. Given our finding that the DOCPs were robust to alternative biological and behavioral assumptions it may be possible to identify DOCPs even when the data are not sufficient to identify a transmission model.

59 BASIC BIOLOGICAL SCIENCES↗

Utah FORGE: Results of Direct Shear Tests on Saturated Joints in Sierra White Granite

This dataset includes an Excel file with the results of direct shear tests to investigate the mechanical and geophysical response of saturated joints. Tests were conducted on induced tension-fractured Sierra White granite joints in a custom water pressurized chamber. The preparation of granite joints is summarized in the PDF file. The PDF file also includes a description of the direct shear tests, experimental procedure, and results.

15 GEOTHERMAL ENERGY↗

Joint Inversion of Regional Waveform, First-Motion Polarity, and Synthetic Aperture Radar Surface Displacement for the Fourth and Sixth North Korean Declared Nuclear Explosions

Here, this study analyzed the Democratic People’s Republic of Korea’s (DPRK) fourth (DPRK4, 6 January 2016 M w 4.49) and sixth (DPRK6, 7 September 2017 M w 5.2) declared nuclear tests, employing a joint seismic and Interferometric Synthetic Aperture Radar (InSAR) inversion to improve understanding of these events and enhance moment tensor (MT) inversion capabilities. The recent efforts have focused on employing seismic waveform and InSAR geodetic deformation data separately to analyze these and the previous nuclear tests (e.g., Chiang et al., 2018; Myers et al., 2018; Wang et al., 2018). Building upon our previous work (Chi-Durán et al., 2021), we performed a joint regional waveform, first-motion (FM) polarity, and surface displacement inversion, which demonstrated improved source-type discrimination, a revised MT solution with reduced scalar moment uncertainty, and an independently constrained location. In this article, we build on the previous results for DPRK6 by including an analysis using a four-layered velocity model with free-surface topography to compute the near-source static deformation Green’s functions. The model consists of a 50 m basalt layer (⁠V P = 2.07 km/s, V S = 1.2 km/s⁠), a 250 m stratified volcanic deposit layer (⁠V P = 1.73 km/s, V S = 1.0 km/s⁠), a 700 m weathered granodiorite layer (⁠V P = 2.5 km/s, V S = 1.3 km/s⁠⁠), and a granodiorite half-space (⁠V P = 5.35 km/s, V S = 3.09 km/s⁠⁠). The half-space shares the velocity of the regional MDJ2 velocity model (Ford et al., 2010), which has proven effective for waveform inversion in the region. This model considers the range of reported values for various lithologies and weathering effects. Our findings show that using the layered velocity model enhances the recovery of source location and depth for both the explosions by improving fits and reducing uncertainties. The joint inversion also improves source-type discrimination and better constrains the scalar seismic moment necessary for downstream yield estimation.

58 GEOSCIENCES↗

Quantify Plasma Response to Non-Axisymmetric (3D) Magnetic Fields in Tokamaks, Final Report for FES (Fusion Energy Sciences) FY2014 Joint Research Target

The goal of the 2014 Joint Research Target (JRT) has been to conduct experiments and analysis to investigate and quantify the response of tokamak plasmas to non-axisymmetric (3D) magnetic fields. Although tokamaks are conceptually axisymmetric devices, small asymmetries often result from inaccuracies in the manufacture and assembly of the magnet coils, or from nearby magnetized objects. In addition, non-axisymmetric fields may be deliberately applied for various purposes. Even at small amplitudes of order 10 -4 of the main axisymmetric field, such “3D” fields can have profound impacts on the plasma performance. The effects are often detrimental (reduction of stabilizing plasma rotation, degradation of energy confinement, localized heat flux to the divertor, or excitation of instabilities) but may in some case be beneficial (maintenance of rotation, or suppression of instabilities). In general, the magnetic response of the plasma alters the 3D field, so that the magnetic field configuration within the plasma is not simply the sum of the external 3D field and the original axisymmetric field. Typically the plasma response consists of a mixture of local screening of the external field by currents induced at resonant surfaces in the plasma, and amplification of the external field by stable kink modes. Thus, validated magnetohydrodynamic (MHD) models of the plasma response to 3D fields are crucial to the interpretation of existing experiments and the prediction of plasma performance in future devices. The non-axisymmetric coil sets available at each facility allow well-controlled studies of the response to external 3D fields. The work performed in support of the 2014 Joint Research Target has included joint modeling and analysis of existing experimental data, and collaboration on new experiments designed to address the goals of the JRT. A major focus of the work was validation of numerical models through quantitative comparison to experimental data, in order to gain confidence in their ability to predict the performance of ITER and other burning plasmas. An important element of this effort was also to verify experimentally the limits of validity of the models. The rest of this overview will summarize the key results of the work.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Improvements in Earthquake Location from Joint Inversion of Seismic and Gravity Observations – Application to the Iran Region

These are slides which show many graphs and datasets for the above-mentioned topic and then concludes with the following: Joint inversion of multiple geophysical datasets improves recovery of velocity structures, particularly in Vs and in shallow parts of the model, in comparison to travel-time only models. Resulting fits to travel time data are minimally degraded by joint inversions. Correspondingly, fits to independent estimates of ground-truth locations are minimally affected by joint inversions.

58 GEOSCIENCES↗

Novel Dissimilar Joints Between Alloy 800H and 2.25%Cr and 1%Mo Steel

Dissimilar metal joints between ferritic steels and nickel base alloys are currently fabricated using conventional arc welding processes with selected filler metal combinations. The dissimilar metal joints contain abrupt changes in composition over a relatively small distance. Many years of service at elevated temperatures has shown that these welds are susceptible to creep and creep fatigue failures. The primary mechanism for these creep failures involves carbon diffusion from the ferritic steel to the nickel base alloy. As a result, a carbon depleted zone is created that contains very few stable carbides. This work used additive manufacturing (AM) technologies as a highly controllable means for reducing carbon migration through theoretically designed, compositionally graded transition joints guided by appropriate thermodynamic, kinetic and heat transfer and fluid flow modeling. The contents of the report include the objectives and tasks set forth by the PI and collaborators, major technical accomplishments throughout the research and additional details in the form of technical publications resulting from the NEUP grant and reports from the collaborating university and national laboratory.

36 MATERIALS SCIENCE↗