Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Equation of state and strength of diamond in high-pressure ramp loading

Diamond is used extensively as a component in high-energy-density experiments, but existing equation of state (EOS) models do not capture its observed response to dynamic loading. In particular, in contrast with first-principles theoretical models of equilibrium multiphase EOS, no solid-solid phase changes have been detected, and no general-purpose EOS models match the measured ambient isotherm. We have performed density functional theory (DFT) calculations of the diamond phase to ~10 TPa, well beyond its predicted range of thermodynamic stability, and used these results as the basis of a Mie-Grüneisen EOS. We also performed DFT calculations of the elastic moduli, and calibrated an algebraic elasticity model for use in simulations. We then estimated the flow stress of diamond by comparison with the stress-density relation measured experimentally in ramp-loading experiments. Furthermore, the resulting constitutive model allows us to place a constraint on the Taylor-Quinney factor (the fraction of plastic work converted to heat) from the observation that diamond does not melt on ramp compression.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Hierarchical Cellulose Superinsulation Membrane

The environment-friendly components coupled with the ability to mimic the simplicity and originality of nature necessitate advanced sustainable materials with structural capabilities for energy-efficient applications. The use of feedstock deriving from plant-based, renewable organic material to produce nanofibril that embodies enhanced insulating properties and high mechanical strength constitutes an efficient development strategy. In this work, a free-standing, hierarchical superinsulation membrane by leveraging the principle of the bottom-up method is reported. The electrospun cellulose nanofibrils/aerogel-based core layer provides exceptional thermal properties with its thermal conductivity of 10.2 mW m –1 K –1 . The lightweight, flexible, and durable paper-like membrane features a tensile strength of 11.3 MPa and a bending rigidity in the order of 4.6 cN mm –1 . The hydrophobic superinsulation membrane material also exhibits a ΔT of ≈25 °C under continuous sunlight illumination and allows thermal runaway mitigation of rechargeable lithium-ion batteries. All the aforementioned properties position this hybrid superinsulation membrane as a promising material for energy-saving thermal management applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Recent Advances in Functional Materials through Cellulose Nanofiber Templating

Advanced templating techniques have enabled delicate control of both nano- and microscale structures and have helped thrust functional materials into the forefront of society. Cellulose nanomaterials are derived from natural polymers and show promise as a templating source for advanced materials. Use of cellulose nanomaterials in templating combines nanoscale property control with sustainability, an attribute often lacking in other templating techniques. Use of cellulose nanofibers for templating has shown great promise in recent years, but previous reviews on cellulose nanomaterial templating techniques have not provided extensive analysis of cellulose nanofiber templating. Cellulose nanofibers display several unique properties, including mechanical strength, porosity, high water retention, high surface functionality, and an entangled fibrous network, all of which can dictate distinctive aspects in the final templated materials. Many applications exploit the unique aspects of templating with cellulose nanofibers that help control the final properties of the material, including, but not limited to, applications in catalysis, batteries, supercapacitors, electrodes, building materials, biomaterials, and membranes. A detailed analysis on the use of cellulose nanofibers templating is provided, addressing specifically how careful selection of templating mechanisms and methodologies, combined toward goal applications, can be used to directly benefit chosen applications in advanced functional materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

PDMS ‐silica composite gas separation membranes by direct ink writing

Abstract Polydimethylsiloxane (PDMS)‐based membranes containing amine‐functionalized and unfunctionalized silica particles were fabricated via direct ink writing for CO 2 /N 2 gas separation. The printability of the inks was evaluated by rheological measurements, while spectroscopy, microscopy, thermal measurements, and mechanical testing were employed to characterize the printed membranes. The surface morphology of the membranes revealed the absence of voids, demonstrating their suitability for gas separation. The printed membranes also exhibited desirable thermal and mechanical properties (i.e., thermal degradation temperature of 518 °C and tensile strength as high as 1.178 MPa with 529% elongation). The PDMS‐based membranes generally displayed high permeability for CO 2 but slightly low selectivity for the CO 2 /N 2 gas pair. The best‐combined permeability‐selectivity performance of 8794 barrer and selectivity of 11.64 was demonstrated by the printed PDMS membrane containing no SiO 2 fillers. The inclusion of unfunctionalized SiO 2 particles generally increased the membrane's gas permeability but compromised the selectivity. In contrast, membranes with amine‐functionalized silica showed improved selectivity compared to membranes containing unfunctionalized silica. Overall, the performance and characteristics offered by the PDMS/silica composite membranes demonstrated the potential of 3D printing as an economical and sustainable fabrication approach to developing materials for carbon capture applications.

Gutierrez, Dianne B.↗
DOE OSTI2025

Investigation of Corrosion Behavior of Carbide Phase Strengthened Nickel‐Based Alloy in Molten Fluoride Salt

The corrosion behavior of a high creep strength carbide-phase strengthened Ni-based alloy in molten FLiNaK (LiF-NaF-KF: 46.5-11.5-42 mol%) salt in the temperature range of 700°C–750°C has been investigated as a part of the development of structural alloys for fluoride salt-based molten salt reactors (MSRs). The alloy composition was designed based on Hastelloy-N, but with the goal of improving creep strength. Cr depletion depth, a measure of corrosion, was observed to be single micrometers after several hundred hours of corrosion testing. Sequential corrosion testing involving testing of pre-tested samples in fresh salt coupled with SEM-EDS, scanning transmission electron microscopy (STEM) examinations and thermodynamic and kinetic modeling, suggest that the corrosion rate at the alloy-salt interface is governed by diffusion of elements from the alloy bulk to the surface. The carbide phases in the corrosion-tested sample microstructure were identified to be largely M 6 C-type Mo-rich carbides and MC-type mixed carbides. Atom probe tomography (APT) showed some partitioning of Cr and Ti to the carbide phase and showed the carbide phases to be stable at the salt-facing surface.

Gordon, Ryan [Univ. of Wisconsin, Madison, WI (Uni↗
DOE OSTI2024

How hydrophobicity, side chains, and salt affect the dimensions of disordered proteins

Abstract Despite the generally accepted role of the hydrophobic effect as the driving force for folding, many intrinsically disordered proteins (IDPs), including those with hydrophobic content typical of foldable proteins, behave nearly as self‐avoiding random walks (SARWs) under physiological conditions. Here, we tested how temperature and ionic conditions influence the dimensions of the N‐terminal domain of pertactin (PNt), an IDP with an amino acid composition typical of folded proteins. While PNt contracts somewhat with temperature, it nevertheless remains expanded over 10–58°C, with a Flory exponent, ν , >0.50. Both low and high ionic strength also produce contraction in PNt, but this contraction is mitigated by reducing charge segregation. With 46% glycine and low hydrophobicity, the reduced form of snow flea anti‐freeze protein (red‐sfAFP) is unaffected by temperature and ionic strength and persists as a near‐SARW, ν ~ 0.54, arguing that the thermal contraction of PNt is due to stronger interactions between hydrophobic side chains. Additionally, red‐sfAFP is a proxy for the polypeptide backbone, which has been thought to collapse in water. Increasing the glycine segregation in red‐sfAFP had minimal effect on ν . Water remained a good solvent even with 21 consecutive glycine residues ( ν > 0.5), and red‐sfAFP variants lacked stable backbone hydrogen bonds according to hydrogen exchange. Similarly, changing glycine segregation has little impact on ν in other glycine‐rich proteins. These findings underscore the generality that many disordered states can be expanded and unstructured, and that the hydrophobic effect alone is insufficient to drive significant chain collapse for typical protein sequences.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Anodization Compatibility of Eutectic Aluminum–Cerium Alloys

Anodizing is the most common method for producing corrosion resistant layer coatings for aluminum alloys. It is possible to use anodizing with most commercial aluminum alloys to increase material corrosion resistance, but often the brittle, passive oxide layer formed during anodization does not adhere well to the material, reducing effectiveness, and overall compatibility. Therefore, it is important for the compatibility and effect of anodization to be studied for any newly developed alloys. Recently developed eutectic Al–Ce alloys offer advantages like high castability, limited or no heat treatment requirements, and high-temperature strength retention. In this work, Al–Ce alloys are shown to have good compatibility with current processes and may exhibit improved adhesion of passivated layer because intermetallic phases anchor the anodized product to unconverted bulk. The source of these phenomena and their effect on material corrosion and layer adhesion properties of Al–Ce alloys will be discussed and compared with results from common commercial aluminum alloys.

Sims, Zachary↗
DOE OSTI2022

Transport and mechanical behavior in PEO-LLZO composite electrolytes

Abstract Composite solid electrolytes (CEs), wherein ion-conducting polymer and ceramic/glass is mixed, are promising candidates for all-solid-state batteries due to their promise of acceptable ionic conductivity and mechanical properties compared to their individual constituents. While numerous studies have focused on improving the performance of CEs, it is still unclear what the material targets are that can result in improved macroscopic performance especially in light of the coupled needs for high transport and high mechanical strength in these materials. In this study, a two-dimensional (2D) mathematical model is developed to investigate electrochemical and mechanical characteristics of CEs. The model is compared to CEs consisting of poly-ethylene-oxide (PEO) polymer and lithium lanthanum zirconium oxide (LLZO) ceramic material with examination of the impact of varying LLZO volume fractions. The potential drop at the PEO-LLZO interface is evaluated using the junction potential theory. Using experimental data from the literature, the model estimates the ionic conductivity, effective transference number, and mechanical stiffness of the CEs. While the mechanical stiffness improves with increasing volume fraction of LLZO, the impact on conductivity and transference number depends on interfacial resistance at the interface. Finally, the study reports CE’s potential to enhance Li-ion transport and mechanical properties to inhibit lithium (Li) dendrite growth.

25 ENERGY STORAGE↗
DOE OSTI2023

Development of coal-derived carbon-based structural unit as a potential new building material

Coal combustion for energy has not only wasted the hydrogen-rich volatile matters but also results in CO 2 emission causing serious environmental issues. An integrated coal pyrolysis and solvent extraction process under elevated temperatures in an inert atmosphere is implemented to convert as-mined coal from Wyoming Powder River Basin to functional carbon elements such as pyrolysis char (PC). This paper presents the development and fabrication of new carbon-based structural unit (CSU) using pulverized PC and two coal-derived pitches (mesophase pitch and tar pitch) to attain high compressive strength greater than 30 MPa, low thermal conductivity less than 0.30 W/m.K, and low density less than 1.25 g/cm 3 . CSUs have the potential to overcome the current challenges with cement and concrete through pressurized fabrication followed by carbonization. This study aims to develop CSU with nearly 100% coal-derived carbon material for structural application in buildings. The effects of pressing pressures, carbonization temperatures, and binder contents on the density and mechanical and thermal properties of CSU samples are investigated. The study concludes that mesophase pitch produces a better performance of CSU samples, a combination of 100 MPa pressing pressure and carbonization temperature of 900 ⁰C yields the highest compressive strength, and a 25% MP content is recommended for low-cost CSU fabrication. Furthermoer, CSU has a much lower density, lower thermal conductivity, higher compressive strength, and higher strength-to-density ratio than normal concrete.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Solving Recent Challenges for Wrought Ni-Base Superalloys

This paper reviews the status of technology in design and manufacture of new wrought 21 polycrystalline Ni-base superalloys for critical engineering applications. There is a strong 22 motivation to develop new alloys that are capable of operating at higher temperatures to 23 realise improvements in thermal efficiency, which are necessary to achieve environmental 24 targets for reduced emissions of harmful green-house gases. From the aerospace sector, 25 the development of new powder metallurgy and ingot metallurgy alloys are discussed for 26 disk rotor and static applications. New compositions for powder metallurgy contain about 27 50-55% of gamma prime (γ') strengthening precipitates to ensure components operate 28 successfully at temperatures up to 788°C (1450°F). In contrast, new compositions for ingot 29 metallurgy aim to occupy a design space in temperature capability between Alloy 718 and 30 current powder alloys that are in-service, and show levels of γ' of about 30-44%. The focus 31 in developing these alloys was design for manufacturability. To complement the aerospace 32 developments, a review of work to understand the suitability of candidate alloys for multiple 33 applications in Advanced-Ultra Supercritical (AUSC) power plants has been undertaken by 34 Detrois, Jablonski and Hawk from the National Energy Technology Laboratory. In these 35 power plants, steam temperatures are required to reach 700-760°C. The common thread is 36 to develop alloys that demonstrate a combination of high temperature properties, which are 37 reliant on both the alloy composition and microstructure and can be produced readily at the 38 right price. For the AUSC applications, the emphasis is on high temperature strength, long 39 term creep life, phase stability, oxidation resistance and robust welding for fabrications. 40 Whereas for powder disk rotors in aircraft engines, the priority is enhanced resistance to 41 time dependent crack growth, phase stability and resistance to environmental damage, while 42 extending the current strength levels, which are shown by existing alloys, to higher 43 temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Review: Magnesium Sheet Alloy Development for Room Temperature Forming

Sheet metal forming operations in the automotive industry, including stamping, flanging, bending, hemming and trimming, are dominantly done at room temperature (RT). Unfortunately, the poor RT formability of magnesium due to its hexagonal close packed (HCP) structure and generally strong texture has limited the use of these processes in high-volume automotive production. However, the formability of magnesium can be improved via fine grain structure and random texture to enable some RT forming operations. Here, this paper presents the latest magnesium alloy development and evaluation by the United States Automotive Materials Partnership (USAMP) in collaboration with its university partners. A new sheet alloy developed in a recent USAMP project, ZAXME11100 (USAMP Alloy 2 Plus), offers excellent ductility (31% tensile elongation) and RT formability (7.8 mm Erichsen Index) in solution-treated condition (T4), and a high yield strength (270 MPa) upon post-forming aging treatment (T6), promising RT forming for automotive applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Bounds on the Rate-Dependent Plastic Flow of Tantalum up to 75 GPa

In this study we report on the continued development of thermodynamics-based analysis of shock waves propagation with the objective of extracting information related to materials strength at high strain rates and pressures. Building on previous results reported for peak stresses of 10 GPa and 25 GPa, we present a series of three-step gas-gun shock experiments designed to explore the pressure and strain rate dependence of plastic flow in polycrystalline tantalum. These experiments at nominal peak stresses of 50 GPa and 75 GPa show the irreversible deformation before pullback to be almost entirely confined to the shock loading, with negligible plastic relaxation on the post-shock plateau. We also add a reverse-ballistics shot at 25 GPa, which was designed to reveal the pullback response with negligible interference from free-surface effects. General thermodynamic considerations allow us to place bounds on the plastic behavior even for parts of the curve that change far too rapidly for the velocimetric time resolution of (conservatively) ~ 5 ns. To analyze the data, we found it necessary to substantially improve the interpolation/extrapolation scheme in order to improve its robustness, flexibility and range of applicability. We describe the new scheme based on splines, as well as an extension of free-surface corrections to the post-shock rarefaction waves. Reanalysis with the new scheme produces results essentially within the error bars previously reported, showing that the known systematic errors associated with free-surface effects are relatively inconsequential for determining thermodynamic paths.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Evolution of global and local deformation in additively manufactured octet truss lattice structures

Additively manufactured lattice truss structures, often referred to as architected cellular materials, present significant advantages over conventional structures due to their unique characteristics such as high strength-to-weight ratios and surface area-to-volume ratios. These geometrically complex structures, however, come with concomitant challenges for qualification and inspection. In this study, compression testing interrupted with micro-computed tomography inspection was conducted to monitor the evolution of global and local deformation throughout the loading process of 304L stainless steel octet truss lattice structures. Both two- and three-dimensional image analysis techniques were leveraged to characterize geometric heterogeneities resulting from the laser powder bed fusion manufacturing process as well as track the structure throughout deformation. Variations from model-predicted behavior resulting from these heterogeneities are considered relative to the predicted and actual responses of the structures during compression to better understand, model, and predict the octet truss lattice structure compression response.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Multi-stage load partitioning in additively manufactured Al6061+TiC nanocomposite characterized by in-situ neutron diffraction

Metal matrix composites (MMCs), combining metal matrix and ceramic particles, exhibit high mechanical strength and stiffness compared to conventional metallic materials. During fusion-based additive manufacturing (AM), MMCs undergo a rapid heating and cooling thermal history, which affects the interfacial bonding, thermal misfit stress and mechanical load transfer behavior between the metal matrix and particles, thus impacting the bulk mechanical performance. Here, we investigate the deformation dynamics and phase-specific load transfer in fusion-based AMed Al6061 +TiC MMCs through in-situ neutron diffraction. By calculating the phase-specific lattice strains, a multi-stage load transfer and deformation behavior during uniaxial compression is revealed: (1) elastic deformation in Stage I for both phases; (2) sudden stress rebalance between two phases in Stage II, evidenced by a sudden decrease in Al lattice strain and increase in TiC; (3) active load carrying by both phases in Stage III, with both phases experiencing an increase in lattice strains. Further, the deformation mechanism of each stage is deducted by correlating the evolutions of the interphase stresses and peaks’ broadening and intensity of the Al matrix. The local plastic deformation of the Al matrix near the phase interface is triggered and leads to stress rebalancing in Stage II. The global plastic deformation subsequently propagates throughout the Al matrix in Stage III, and the composite is further hardened through both dislocation multiplication and load transfer. The findings offer valuable insights into deformation and load-sharing behavior in AMed MMCs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Application of machine learning for modeling brønsted-guggenheim-scatchard specific ion interaction theory (SIT) coefficients

Machine learning methodologies can provide insight into Brønsted-Guggenheim-Scatchard specific ion interaction theory (SIT) parameter values where experimental data availability may be limited. This study develops and executes machine learning frameworks to model the SIT interaction coefficient, ε. Key findings include successful estimations of ε via artificial neural networks using clustering and value prediction approaches. Additionally, applicability to other chemical parameters is also assessed briefly. Models developed here provide support for a use-case of machine learning in geologic nuclear waste disposal research applications, namely in predictions of chemical behaviors of high ionic strength solutions (i.e., subsurface brines).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Analysis of the turbostratic structures in PAN-based carbon fibers with wide-angle x-ray diffraction

Carbon fiber (CF) is a versatile material renowned for its excellent mechanical, thermal, and electrical properties. Polyacrylonitrile (PAN)-based CFs dominate the market due to their high tensile strength, rendering them suitable for structural applications in a wide variety of applications ranging from sporting goods to aerospace. Over five decades of commercial development of PAN-based CF has resulted in a range of varieties with different tensile moduli and tensile strengths. The microstructures, nanostructures, and crystal structures of PAN-based CF play pivotal roles in the macroscale properties of this material. In particular, the crystal structure and crystallite orientation in CF is closely related to the mechanical properties. The crystal structure of PAN-based CF generally consists of turbostratic carbon, which is a disordered form of graphite, the characteristics of which can be effectively characterized in a bulk format through wide-angle x-ray diffraction (WAXD). In this work, we employed a three-part approach to the analysis of WAXD patterns collected from four intermediate modulus PAN-based CFs. The approach incorporates a Scherrer analysis, a Debye analysis, and an orientational analysis to provide precise estimates of crystallite sizes, crystallite distributions, and crystallite orientations with the fiber axis. Furthermore, the results presented here suggest that intermediate modulus PAN-based CF mostly consists of small turbostratic crystallites (<4 nm), with larger crystallites having increased orientation with the fiber axis. The results here imply the presence of curvature and/or wrinkling of the turbostratic layers within the CF structure.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Hydration of potassium citrate-activated BOF slag

Basic Oxygen Furnace (BOF) slag is currently utilized with low-grade applications or landfilled. Here, we investigate a novel route to upgrade BOF slag to a high-performance binder by chemical activation with tri-potassium citrate. The impact of tri-potassium citrate on hydration and phase assemblage of BOF slag is analyzed with a multi-technique approach. Results reveal that the addition of tri-potassium citrate considerably enhances the reactivity of brownmillerite and accelerates the hydration of belite at early ages. The majority of brownmillerite hydrates within 24 h, and the reaction kinetics is controlled by the activator dosage. The main products of BOF slag hydration are siliceous hydrogarnet and C-S-H gel. Acting as a strong water reducer, tri-potassium citrate enables the manufacture of slag pastes with high compressive strength (up to 75 MPa at 28 days) and low porosity. Leaching of heavy metals from the slag pastes fulfills the Dutch Soil Quality Decree limits.

36 MATERIALS SCIENCE↗