Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “growth processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Dysprosium oxide and dysprosium-oxide-doped titanium oxide thin films grown by atomic layer deposition

Dysprosium oxide and dysprosium-oxide-doped titanium oxide thin films were grown by atomic layer deposition on silicon substrates. For depositing dysprosium and titanium oxides Dy(thd){sub 3}-O{sub 3} and TiCl{sub 4}-O{sub 3} were used as precursors combinations. Appropriate parameters for Dy(thd){sub 3}-O{sub 3} growth process were obtained by using a quartz crystal microbalance system. The Dy{sub 2}O{sub 3} films were deposited on planar substrates and on three-dimensional substrates with aspect ratio 1:20. The Dy/Ti ratio of Dy{sub 2}O{sub 3}-doped TiO{sub 2} films deposited on a planar silicon substrate ranged from 0.04 to 0.06. Magnetometry studies revealed that saturation of magnetization could not be observed in planar Dy{sub 2}O{sub 3} films, but it was observable in Dy{sub 2}O{sub 3} films on 3D substrates and in doped TiO{sub 2} films with a Dy/Ti atomic ratio of 0.06. The latter films exhibited saturation magnetization 10{sup −6} A cm{sup 2} and coercivity 11 kA/m at room temperature.

36 MATERIALS SCIENCE↗

Enhanced-Adhesion Multi-Walled Carbon Nanotubes on Titanium Substrates for Stray Light Control

Carbon nanotubes previously grown on silicon have extremely low reflectance, making them a good candidate for stray light suppression. Silicon, however, is not a good structural material for stray light components such as tubes, stops, and baffles. Titanium is a good structural material and can tolerate the 700 C nanotube growth process. The ability to grow carbon nanotubes on a titanium substrate that are ten times blacker than the current NASA state-of-the-art paints in the visible to near infrared spectra has been achieved. This innovation will allow significant improvement of stray light performance in scientific instruments or any other optical system. This innovation is a refinement of the utilization of multiwalled carbon nano tubes for stray light suppression in spaceflight instruments. The innovation is a process to make the surface darker and improve the adhesion to the substrate, improving robustness for spaceflight use. Bright objects such as clouds or ice scatter light off of instrument structures and components and make it difficult to see dim objects in Earth observations. A darker material to suppress this stray light has multiple benefits to these observations, including enabling scientific observations not currently possible, increasing observational efficiencies in high-contrast scenes, and simplifying instruments and lowering their cost by utilizing fewer stray light components and achieving equivalent performance. The prior art was to use commercially available black paint, which resulted in approximately 4% of the light being reflected (hemispherical reflectance or total integrated scatter, or TIS). Use of multiwalled carbon nanotubes on titanium components such as baffles, entrance aperture, tubes, and stops, can decrease this scattered light by a factor of ten per bounce over the 200-nm to 2,500-nm wavelength range. This can improve system stray light performance by orders of magnitude. The purpose of the innovation is to provide an enhanced stray light control capability by making a blacker surface treatment for typical stray light control components. Since baffles, stops, and tubes used in scientific observations often undergo loads such as vibration, it was critical to develop this surface treatment on structural materials. The innovation is to optimize the carbon nanotube growth for titanium, which is a strong, lightweight structural material suitable for spaceflight use. The titanium substrate carbon nanotubes are more robust than those grown on silicon and allow for easier utilization. They are darker than current surface treatments over larger angles and larger wavelength range. The primary advantage of titanium substrate is that it is a good structural material, and not as brittle as silicon.

Hagopian, John↗

Dual-wavelength laser diodes based on epitaxially stacked heterostructures

AlGaAs/GaAs double laser heterostructures containing two different active regions have been grown by metalorganic vapour phase epitaxy in a single growth process, and their properties have been studied. A typical slope of their power - current curves is 2.3 W A{sup -1}, which is almost twice that for a laser diode (1.2 W A{sup -1}). We demonstrate lasing of the emitter regions of the dual-wavelength lasers in the range 800 - 815 nm, with a separation between the peaks of {approx}7 nm. The observed effect of pump current on the lasing wavelength of the active regions in the dual-wavelength and single lasers indicates that the emitter region farther away from the heat sink is more sensitive to pump current variations. (lasers)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Crystallization kinetics and spectroscopic investigations on Tb{sup 3+} and Yb{sup 3+} codoped glass ceramics containing CaF{sub 2} nanocrystals

Transparent Tb{sup 3+} and Yb{sup 3+} codoped oxyfluoride glass ceramics containing CaF{sub 2} nanocrystals were prepared by melt quenching and subsequent heat treatment. Crystallization kinetics of CaF{sub 2} nanocrystals was investigated by differential scanning calorimetric method. The average apparent activation energy E{sub a} of the crystallization was {approx}498 kJ/mol. Moreover, the value of the Avrami exponent n was 1.01. These results suggest that the crystallization mechanism of CaF{sub 2} is a diffusion controlled growth process of needles and plates of finite long dimensions. X-ray diffraction patterns and transmission electron microscopy image confirmed the CaF{sub 2} nanocrystals in the glass ceramic. Ultraviolet (UV) and visible emission spectra of the as-made glass and the glass ceramic with an excitation of a 974 nm laser diode were recorded at room temperature. An intense UV emission at 381 nm was observed in the glass ceramic. The origin of the enhancement of the emission at 381 nm was investigated using spectroscopic technique and Judd-Ofelt analysis. The enhancement of the emission at 381 nm could be attributed to the change of the ligand field of Tb{sup 3+} ions due to the incorporation of some Tb{sup 3+} and Yb{sup 3+} ions into CaF{sub 2} nanocrystals in the glass ceramic.

36 MATERIALS SCIENCE↗

Leakage mechanisms and potential performance of molecular-beam epitaxially grown GaInAsSb 2.4 {mu}m photodiode detectors

We report on the growth, processing, and characterization of uncoated, unpassivated GaInAsSb detector mesa photodiodes with a cutoff wavelength of 2.4 {mu}m. We find peak room temperature specific detectivity value of 6x10{sup 10} cm Hz{sup 1/2}/W and maximum zero-bias resistivity of 25 {omega} cm{sup 2}. The zero-bias resistivities of mesas with areas ranging from 50{sup 2} {mu}m{sup 2} to 1 mm{sup 2} were found to be limited by generation-recombination currents at mesa sidewalls. At low temperatures, devices were limited by Ohmic leakage, which is likely due to the formation of oxides on the sidewalls. After 6 months of aging, Ohmic leakage becomes the limiting factor at room temperature as well. Based on experimentally obtained material parameters in this and other studies, an upper limit D* and R{sub 0}A were estimated for GaInAsSb materials and compared to those HgCdTe and InGaAs.

36 MATERIALS SCIENCE↗

Growth and melting of metallic nanoclusters in glass: A review of recent investigations

The mechanisms of nucleation and growth and the solid-to-liquid transition of metallic nanoclusters embedded in sodium borate glass were recently studied in situ via small-angle X-ray scattering (SAXS) and wide-angle X-ray scattering (WAXS). SAXS results indicate that, under isothermal annealing conditions, the formation and growth of Bi or Ag nanoclusters embedded in sodium borate glass occurs through two successive stages after a short incubation period. The first stage is characterized by the nucleation and growth of spherical metal clusters promoted by the diffusion of Bi or Ag atoms through the initially supersaturated glass phase. The second stage is named the coarsening stage and occurs when the (Bi-or Ag-) doping level of the vitreous matrix is close to the equilibrium value. The experimental results demonstrated that, at advanced stages of the growth process, the time dependence of the average radius and density number of the clusters is in agreement with the classical Lifshitz-Slyozov-Wagner (LSW) theory. However, the radius distribution function is better described by a lognormal function than by the function derived from the theoretical LSW model. From the results of SAXS measurements at different temperatures, the activation energies for the diffusion of Ag and Bi through sodium borate glass were determined. In addition, via combination of the results of simultaneous WAXS and SAXS measurements at different temperatures, the crystallographic structure and the dependence of melting temperature T{sub m} on crystal radius R of Bi nanocrystals were established. The experimental results indicate that T{sub m} is a linear and decreasing function of nanocrystal reciprocal radius 1/R, in agreement with the Couchman and Jesser theoretical model. Finally, a weak contraction in the lattice parameters of Bi nanocrystals with respect to bulk crystals was established.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Preparation and structural characterization of FeCo epitaxial thin films on insulating single-crystal substrates

FeCo epitaxial films were prepared on MgO(111), SrTiO{sub 3}(111), and Al{sub 2}O{sub 3}(0001) single-crystal substrates by ultrahigh vacuum molecular beam epitaxy. The effects of insulating substrate material on the film growth process and the structures were investigated. FeCo(110){sub bcc} films grow on MgO substrates with two type domains, Nishiyama-Wassermann (NW) and Kurdjumov-Sachs (KS) relationships. On the contrary, FeCo films grown on SrTiO{sub 3} and Al{sub 2}O{sub 3} substrates include FeCo(111){sub bcc} crystal in addition to the FeCo(110){sub bcc} crystals with NW and KS relationships. The FeCo(111){sub bcc} crystal consists of two type domains whose orientations are rotated around the film normal by 180 deg. each other. The out-of-plane and the in-plane lattice spacings of FeCo(110){sub bcc} and FeCo(111){sub bcc} crystals formed on the insulating substrates are in agreement with those of the bulk Fe{sub 50}Co{sub 50} (at. %) crystal with small errors ranging between +0.2% and +0.4%, showing that the strains in the epitaxial films are very small.

36 MATERIALS SCIENCE↗

Development of a triple-moment ice-phase cloud microphysics scheme and its application to the Single Column Atmosphere Model

Parameterization of cloud microphysics is critical for accurate simulation of weather and climate, in which the characteristics of cloud particle spectrum inevitably further affect climate simulation by changing the cloud evolution and cloud radiation effects. The popular currently used double-moment cloud microphysics schemes in numerical models can predict the intercept (N 0 ) and slope (λ) parameters of cloud particle spectrum but cannot predict the spectral shape parameter (μ), which hinders accurate description of cloud physical processes in climate models. Therefore, in the present study, we built upon the ideas of previously developed triple-moment cloud microphysics scheme, considered radar reflectivity factor as the third predictor in addition to number and mass concentration, and introduced its related prediction equation to the Single Column Atmosphere Model Version 5.3 (SCAM5.3). Moreover, the relevant microphysical process formulas in the model were revised, and a triple-moment ice-cloud microphysics scheme was constructed to predict the μ of ice particle spectrum. Based on this model, a 29-day case of the Atmospheric Radiation Measurement Program in the summer of 1997 (ARM97) was simulated, and the differences in cloud fraction and radiation simulations between the double- and triple-moment schemes were analysed. The μ of ice particle spectrum predicted by the triple-moment scheme mainly ranged from 0 to 4; the peak value was around 2, and at least 85% of the μ values were greater than the default 0. Therefore, the μ=0 setting in the double-moment scheme is unreasonable. Moreover, the developed triple-moment ice-cloud microphysics scheme yielded a narrower ice particle spectrum, which was closer to the observation results of previous studies, than the double-moment cloud microphysics scheme (e.g., height=233 hPa). Furthermore, compared with the double-moment scheme, the triple-moment scheme achieved closer simulations of the cloud fraction observations, particularly for ice clouds in the upper levels. Considering the close association between cloud fraction and radiation, the error with the triple-moment scheme was smaller than that with the double-moment scheme regardless of the shortwave (surface downward shortwave radiation, net downward shortwave radiation at the top of the atmosphere, and net shortwave radiation at the surface) or longwave (surface downward longwave radiation and net longwave radiation at the surface) flux density. Finally, the improvement mechanism of the triple-moment scheme on cloud fraction and radiation simulations was explored. The major reason is that the triple-moment scheme weakens the autoconversion of ice crystal to form snow and enhances the growth process of ice crystal deposition, thereby increasing the mass concentration of ice crystals and ice cloud fraction. Overall, the developed triple-moment ice-cloud microphysics scheme can help improve the simulation ability of models for cloud-climate feedback and other processes.

54 ENVIRONMENTAL SCIENCES↗

Surface Morphology and Electrical Properties of Cu 3 BTC 2 Thin Films Before and After Reaction with TCNQ

HKUST-1 or Cu 3 BTC 2 (BTC = 1,3,5-benzenetricarboxylate) is a prototypical metal–organic framework (MOF) that holds a privileged position among MOFs for device applications, as it can be deposited as thin films on various substrates and surfaces. Recently, new potential applications in electronics have emerged for this material when HKUST-1 was demonstrated to become electrically conductive upon infiltration with 7,7,8,8-tetracyanoquinodimethane (TCNQ). However, the factors that control the morphology and reactivity of the thin films are unknown. Here, we present a study of the thin-film growth process on indium tin oxide and amorphous Si prior to infiltration. From the unusual bimodal, non-log-normal distribution of crystal domain sizes, we conclude that the nucleation of new layers of Cu 3 BTC 2 is greatly enhanced by surface defects and thus difficult to control. We then show that these films can react with methanolic TCNQ solutions to form dense films of the coordination polymer Cu(TCNQ). This chemical conversion is accompanied by dramatic changes in surface morphology, from a surface dominated by truncated octahedra to randomly oriented thin platelets. The change in morphology suggests that the chemical reaction occurs in the liquid phase and is independent of the starting surface morphology. The chemical transformation is accompanied by 10 orders of magnitude change in electrical conductivity, from <10 –11 S/cm for the parent Cu 3 BTC 2 material to 10 –1 S/cm for the resulting Cu(TCNQ) film. In conclusion, the conversion of Cu 3 BTC 2 films, which can be grown and patterned on a variety of (nonplanar) substrates, to Cu(TCNQ) opens the door for the facile fabrication of more complex electronic devices.

2D nucleation↗

Photoelectrochemical properties of n-type KTaO3 single crystals in alkaline electrolytes

Semiconducting KTaO3 single crystals have been investigated as a model potential photoanode for hydrogen production using photoelectrochemical (PEC) cells. In order to modify the electronic properties of KTaO3 by reducing the bandgap and thereby increase the absorption of light at longer wavelengths, KTaO3 single crystals were doped during the crystal growth process. A wide range of dopant elements was employed that consisted primarily of transition metals - due to the established effects they have exhibited in modifying the properties of other semiconducting systems such as TiO2. With the exception of the crystals grown with LiCO3 or B2O3 added to the melt (resulting in crystals that were not effectively doped), the crystals exhibited n-type behavior with carrier concentrations ranging from 4 x 1018 to 2.6 x 1020 cm-3. The position of the band edges indicated that the crystals were thermodynamically capable of water dissociation without the application of an external bias. External quantum yield (QY) measurements revealed that the samples were photoactive up to a wavelength of ~350 nm. Higher QY s were measured when some of the crystals were thermochemically treated in a CO atmosphere. The indirect bandgap and a parameter denoted as E1 that is related to the direct band edge of the semiconductor were found to be the same within the statistical error for all the samples. These results indicate that the various dopants and treatments did not produce changes in the KTaO3 electronic structure that were sufficient to significantly modify the behavior exhibited by this material in a PEC cell.

08 HYDROGEN↗

Airborne Observations of Aerosol Emissions from F-16 Aircraft

We presented results from the SASS Near-Field Interactions Flight (SNIF-III) Experiment which was conducted during May and June 1997 in collaboration with the Vermont and New Jersey Air National Guard Units. The project objectives were to quantify the fraction of fuel sulfur converted to S(VI) species by jet engines and to gain a better understanding of particle formation and growth processes within aircraft wakes. Size and volatility segregated aerosol measurements along with sulfur species measurements were recorded in the exhaust of F-16 aircraft equipped with F-100 engines burning fuels with a range of fuel S concentrations at different altitudes and engine power settings. A total of 10 missions were flown in which F-16 exhaust plumes were sampled by an instrumented T-39 Sabreliner aircraft. On six of the flights, measurements were obtained behind the same two aircraft, one burning standard JP-8 fuel and the other either approximately 28 ppm or 1100 ppm S fuel or an equal mixture of the two (approximately 560 ppm S). A pair of flights was conducted for each fuel mixture, one at 30,000 ft altitude and the other starting at 35,000 ft and climbing to higher altitudes if contrail conditions were not encountered at the initial flight level. In each flight, the F-16s were operated at two power settings, approx. 80% and full military power. Exhaust emissions were sampled behind both aircraft at each flight level, power setting, and fuel S concentration at an initial aircraft separation of 30 m, gradually widening to about 3 km. Analyses of the aerosol data in the cases where fuel S was varied suggest results were consistent with observations from project SUCCESS, i.e., a significant fraction of the fuel S was oxidized to form S(VI) species and volatile particle emission indices (EIs) in comparably aged plumes exhibited a nonlinear dependence upon the fuel S concentration. For the high sulfur fuel, volatile particle EIs in 10-second-old-plumes were 2 to 3 x 10 (exp 17) / kg of fuel burned and exhibited no obvious trend with engine power setting or flight altitude. In contrast, about 8-fold fewer particles were observed in similarly aged plumes from the same aircraft burning fuel with 560 ppm S content and EIs of 1 x 10(exp 15)/ kg of fuel burned were observed in the 28 ppm S fuel case. Moreover, data recorded as a function of plume age indicates that formation and growth of the volatile particles proceeds more slowly as the fuel S level is reduced. For example, ultrafine particle concentrations appear to stabilize within 5 seconds after emission in the 1100 ppm S cases but are still increasing in 20-second old plumes produced from burning the 560 ppm S fuel.

Anderson, B. E.↗

Evaluation of Melt-Grown, ZnO Single Crystals for Use as Alpha-Particle Detectors

As part of an ongoing investigation of the scintillation properties of zinc-oxide-based scintillators, several melt-grown, ZnO single crystals have been characterized using -particle excitation, infrared reflectance, and room temperature photoluminescence. The crystals, grown by Cermet, Inc. using a pressurized melt growth process, were doped with Group 1 elements (Li), Group 2 elements (Mg), Group 3 elements (Ga, In) and Lanthanides (Gd, Er, Tm). The goals of these studies are to better understand the scintillation mechanisms associated with various members of the ZnO scintillator family and to then use this knowledge to improve the radiation detection capabilities of ZnO-based scintillators. One application for which ZnO is particularly well suited as a scintillator is as the associated particle detector in a deuterium-tritium (D-T) neutron generator. Application requirements include the exclusion of organic materials, outstanding timing resolution, and high radiation resistance. ZnO(Ga) and ZnO(In) have demonstrated fast (sub-nanosecond) decay times with relatively low light yields, and ZnO(Ga) has been used in a powder form as the associated particle detector for a D-T neutron generator. Four promising candidate materials, ZnO, ZnO:Ga, ZnO:In,Li, and ZnO:Er,Li, were identified in this study. These four samples demonstrated sub-nanosecond decay times and alpha particle excited luminescence comparable to BC-400 fast plastic scintillator. The ZnO:Mg,Ga, ZnO:Gd, and ZnO:Li samples demonstrated appreciable slow (microsecond) decay components that would be incompatible with high-counting-rate applications.

36 MATERIALS SCIENCE↗

Microbial Cell Imaging

Atomic force microscopy (AFM) is finding increasing application in a variety of fields including microbiology. Until the emergence of AFM, techniques for ivnestigating processes in single microbes were limited. From a biologist's perspective, the fact that AFM can be used to generate high-resolution images in buffers or media is its most appealing feature as live-cell imaging can be pursued. Imaging living cells by AFM allows dynamic biological events to be studied, at the nanoscale, in real time. Few areas of biological research have as much to gain as microbiology from the application of AFM. Whereas the scale of microbes places them near the limit of resolution for light microscopy. AFM is well suited for the study of structures on the order of a micron or less. Although electron microscopy techniques have been the standard for high-resolution imaging of microbes, AFM is quickly gaining favor for several reasons. First, fixatives that impair biological activity are not required. Second, AFM is capable of detecting forces in the pN range, and precise control of the force applied to the cantilever can be maintained. This combination facilitates the evaluation of physical characteristics of microbes. Third, rather than yielding the composite, statistical average of cell populations, as is the case with many biochemical assays, the behavior of single cells can be monitored. Despite the potential of AFM in microbiology, there are several limitations that must be considered. For example, the time required to record an image allows for the study of gross events such as cell division or membrane degradation from an antibiotic but precludes the evaluation of biological reactions and events that happen in just fractions of a second. Additionally, the AFM is a topographical tool and is restricted to imaging surfaces. Therefore, it cannot be used to look inside cells as with opticla and transmission electron microscopes. other practical considerations are the limitation on the maximum scan size (roughly 100 x 100 {mu}m) and the restricted movement of the cantilever in the Z (or height) direction. In most commercial AFMs, the Z range is restricted to roughly 10 {mu}m such that the height of cells to be imaged must be seriously considered. Nevertheless, AFM can provide structural-functional information at nanometer resolution and do so in physiologically relevant environments. Further, instrumentation for scanning probe microscopy continues to advance. Systems for high-speed imaging are becoming available, and techniques for looking inside the cells are being demonstrated. The ability to combine AFM with other imaging modalities is likely to have an even greater impact on microbiological studies. AFM studies of intact microbial cells started to appear in the literature in the 1990s. For example, AFM studies of Saccharomyces cerevisiae examined buddings cars after cell division and detailed changes related to cell growth processes. Also, the first AFM studies of bacterial biofilms appeared. In the late 1990s, AFM studies of intact fungal spores described clear changes in spore surfaces upon germination, and studies of individual bacterial cells were also described. These early bacterial imaging studies examined changes in bacterial morphology due to antimicrobial peptides exposure and bacterial adhesion properties. The majority of these early studies were carried out on dried samples and took advantage of the resolving power of AFM. The lack of cell mounting procedures presented an impediment for cell imaging studies. Subsequently, several approaches to mounting microbial cells have been developed, and these techniques are described later. Also highlighted are general considerations for microbial imaging and a description of some of the various applications of AFM to microbiology.

60 APPLIED LIFE SCIENCES↗

Nanostructured Lanthanum Halides and CeBr3 for Nuclear Radiation and Detection

Scintillator materials are used to detect, and in some cases identify, gamma rays. Higher performance scintillators are expensive, hard to manufacture, fragile, and sometimes require liquid nitrogen or cooling engines. But whereas lower-quality scintillators are cheap, easy to manufacture, and more rugged, their performance is lower. At issue: can the desirable qualities of high-and low-performance scintillators be combined to achieve better performance at lower cost? Preliminary experiments show that a LaF{sub 3}:Ce oleic acid-based nanocomposite exhibits a photopeak when exposed to {sup 137}Cs source gamma-radiation. The chemical synthesis of the cerium-doped lanthanum halide nanoparticles are scalable and large quantities of material can be produced at a time, unlike typical crystal growth processes such as the Bridgeman process. Using a polymer composite (Figure 1), produced by LANL, initial measurements of the unloaded and 8% LaF{sub 3}:Ce-loaded sample have been made using {sup 137}Cs sources. Figure 2 shows an energy spectrum acquired for CeF{sub 3}. The lighter plot is the measured polymer-only spectrum and the black plot is the spectrum from the nanocomposite scintillator. As the development of this material continues, the energy resolution is expected to improve and the photopeak-to-Compton ratio will become greater at higher loadings. These measurements show the expected Compton edge in the polymer-only sample, and the Compton edge and photo-peak expected in the nanophosphor composites that LANL has produced. Using a porous VYCORR with CdSe/ZnS core shell quantum dots, Letant has demonstrated that he has obtained signatures of the 241Am photopeak with energy resolution as good at NaI (Figure 3). We begin with the fact that CeBr{sub 3} crystals do not have a self-activity component as strong as the lanthanum halides. The radioactive 0.090% {sup 138}La component of lanthanum leads to significant self-activity, which will be a problem for very large detector volumes. Yet a significant strength of the nanostructure detector concept is the ability to create extremely large detector volumes by mixing nanoparticles into a transparent matrix. This would argue for use of nanoparticles other than lanthanum halides. Nanocomposites are easy to prepare; it is much less costly to use nanocomposites than to grow large whole crystals of these materials. The material can be fabricated at an industrial scale, further reducing cost. This material potentially offers the performance of $300/cc material (e.g., lanthanum bromide) at a cost of $1/cc. Because the material acts as a plastic, it is rugged and flexible, and can be made in large sheets, increasing the sensitivity of a detector using it. It would operate at ambient temperatures. Very large volumes of detector may be produced at greatly reduced cost, enhancing the non-proliferation posture of the nation for the same dollar value.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Highly Supercooled Riming and Unusual Triple-Frequency Radar Signatures Over McMurdo Station, Antarctica

Riming of ice crystals by supercooled water droplets is an efficient ice growth process, but its basic properties are still poorly known. While it has been shown to contribute significantly to surface precipitation at mid-latitudes, little is known about its occurrence at high latitudes. In Antarctica, two competing effects can influence the occurrence of riming: (i) the scarcity of supercooled liquid water clouds due to the extremely low tropospheric temperatures and (ii) the low aerosol concentration, which may lead to the formation of fewer and larger supercooled drops potentially resulting in an enhanced riming efficiency. In this work, by exploiting the deployment of an unprecedented number of multiwavelength remote sensing systems (including triple-frequency radar measurements) in West Antarctica, during the Atmospheric Radiation Measurements West Antarctic Radiation Experiment (AWARE) field campaign, we evaluate the riming incidence at McMurdo Station and find that riming occurs at much lower temperatures when compared to previous results in the mid-latitudes. This suggests the possible occurrence of a common atmospheric state over Antarctica that includes a rather stable atmosphere inhibiting turbulent mixing, and a high riming efficiency driven by large cloud droplets. We then focus on a peculiar case study featuring a persistent layer with a particularly pronounced riming signature in triple-frequency radar data but only a relatively modest amount of supercooled liquid water. In-depth analysis of the radar observations suggests that such signatures can only be explained by the combined effects of moderately rimed aggregates or similarly shaped florid polycrystals and a narrow particle size distribution (PSD). Simulations of this case study performed with a one-dimensional bin model indicate that similar triple-frequency radar observations can be reproduced when narrow PSDs are simulated. Such narrow PSDs can in turn be explained by two key factors: (i) the presence of a shallow homogeneous droplet or humidified aerosol freezing layer aloft seeding an underlying supercooled liquid layer, and (ii) the absence of turbulent mixing throughout a stable polar atmosphere that sustains narrow PSDs, as hydrometeors grow from the nucleation region aloft to ice particles of several millimeters in size, by vapor deposition and then riming.

Riming↗

Suppression of Defects and Deep Levels Using Isoelectronic Tungsten Substitution in Monolayer MoSe 2

Chemical vapor deposition (CVD) is one of the most promising, scalable synthetic techniques to enable large-area synthesis of two-dimensional (2D) transition metal dichalcogenides (TMDs) for the realization of next generation optoelectronic devices. However, defects formed during the CVD growth process currently limit the quality and electronic properties of 2D TMDs. Effective synthesis and processing strategies to suppress defects and enhance the quality of 2D TMDs are urgently needed. In this work, isoelectrnic doping to produce stable alloy is presented as a new strategy to suppress defects and enhance photoluminescence (PL) in CVD-grown TMD monolayers. The random, isoelectronic substitution of W atoms for Mo atoms in CVD-grown monolayers of Mo 1-x W x Se 2 (0 2 monolayers. The resultant decrease in defect-medicated non-radiative recombination in the Mo 0.82 W 0.18 Se 2 monolayers yielded ~10 times more intense PL and extended the carrier lifetime by a factor of 3 compared to pristine CVD-grown MoSe 2 monolayers grown under similar conditions. Low temperatures (4 125 K) PL from defect-related localized states confirms theoretical predictions that isoelectronic W alloying should suppress deep levels in MoSe 2 , showing that the defect levels in Mo 1-x W x Se 2 monolayers are higher in energy and quenched more quickly than in MoSe 2 . Isoelectronic substitution therefore appears to be a promising synthetic method to control the heterogeneity of 2D TMDs to realize the scalable production of high performance optoelectronic and electronic devices.

36 MATERIALS SCIENCE↗

Concurrent Synthesis of High-Performance Monolayer Transition Metal Disulfides

To date, the chemical vapor deposition (CVD) approach has been widely used for the growth of transition metal dichalcogenides (TMDs). However, the reported CVD methods to synthesize TMDs cannot be used to grow more than one type of TMDs. This work reports a promising CVD technique to concurrently synthesize multiple monolayer transition metal disulfides once. The optoelectrical characterization and high-resolution transmission electron microscopy show the high quality of monolayer crystals, and, more importantly, there is no mixing between different precursors during the growth process, which has been investigated by considering the gas flow dynamics and concentration distribution of precursors in our setup. This strategy indicates the promising future for the batch production of 2D materials and the concurrent synthesis techniques in standard state-of-the-art complementary metal-oxide-semiconductor (CMOS) fabrication technology.

36 MATERIALS SCIENCE↗