SEARCH · Engineering Papers

Results for “filler”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Thermal performance modification of composite materials

This paper reports on an investigation of the concept of modifying the thermal performance of filled polymers through a minor compositional change (presently by coating the filler). The fire-safety of construction materials and the instability of solid rockets are used as examples. A theory is developed which shows that vast improvements are possible by controlling thermal conductivity. Experiments are described that show the weight loss and smoke density in the NBS smoke-density chamber of fiberglass-reinforced epoxy panels, and the instability trends of an AP-HTPB propellant fired in an L-Star rocket motor. The feasibility of tailoring thermal behavior to suit each particular need is demonstrated.

Ramohalli, K.↗

NASA NTRS1979

Non-flammable polyimide materials for commercial application

Thermally-stable, fire-resistant polyimide foams developed for use as fire protection in aircraft, spacecraft and ground applications are presented. Polyimide precursors, synthesized by the reaction of 3, 3', 4, 4'-benzophenone tetracarboxylic acid dianhydride with a mixture of two diamines, can be processed into foams by indirect or direct heating techniques. Flexible resilient foams and thermal acoustical foams produced by the microwave heating of polyimide precursors are shown to conform to requirements for aircraft seating foams and thermal and acoustical insulation materials, respectively. Rigid polyimide foams reinforced by carbon mat, chopped carbon mat and chopped glass strand fillers and prepared by the microwave heating of a continuous mat, followed by its compression, or by filling a honeycomb structure with low density foam, are found to exhibit outstanding fire resistance and have mechanical properties approaching those desired for structural materials.

Gagliani, J.↗

NASA NTRS1980

Flush-mounting technique for composite beams

Procedure permits mounting of heavy parts to surface of composite beams without appreciably weakening beam web. Web is split and held apart in region where attachment is to be made by lightweight precast foam filler. Bolt hole penetrates foam rather than web, and is secured by barrelnut in transverse bushing through web.

Harman, T. C.↗

NASA NTRS1980

Thermal barrier and gas seal

Resilient baglike seal tolerates thousand-degree temperatures and accommodates small changes in gap size without losing gas-barrier properties; at same time, it maintains smooth aerodynamic surface across gap. Seal includes alumina filler backed by metal plate. Alumina-filled envelope is easily handled and installed, and can be used in high-temperature industrial processes like coal gasification and liquefaction.

Kane, J. O.↗

NASA NTRS1981

A new family of fire-resistant foams

Need for lightweight flame-resistant, nonsmoking materials in interiors of spacecraft has spawned family of foams that could find applications in aircraft and other vehicles. Polyimide-based foams are being developed as resilient fillers for seat cushions, as rigid, low-density wall panels, as high-strength sheets for floors, and as thermal and acoustical insulation.

Gagliani, J.↗

NASA NTRS1981

Modified fire-resistant foams forseat cushions

Modified polyimide-polymer resins are precursors for new family of resilient fire-resistant foams. Terpolyimide foams containing long-chain aliphatic diamines withstand 50,000 cycles of compression over a 200 pound load - an equivalent of 3 years of continuous use as seat cushion filler.

Gagliani, J.↗

NASA NTRS1981

One-step microwave foaming and curing

Process that combines microwave foaming and curing of polyimide precursors in single step produces fire-resistant foam slabs of much larger volume than has previously been possible. By adding selected conductive fillers to powder precursors and by using high-power microwave oven, foam slabs with dimensions in excess of 61 by 61 by 7.6 cm are made. Typical foaming and curing and curing time is 35 minutes in microwave oven with additional 1 to 2 hour postcure in conventional oven.

Gagliani, J.↗

NASA NTRS1981

Rigid fire-resistant foams for walls and floors

Previous techniques for fabricating rigid fire-resistant polyimide foams by compressing already-foamed precursor have been supplanted by one-step constrained-rise process. Precursor mixed with reinforcing fillers is placed between rigid substrates that constrain expansion of foam as it is heated by microwave energy. Process works for both liquid and powder precursors and can also be adapted to attach woven fiberglass skins at same time prcursor is being foamed.

Gagliani, J.↗

NASA NTRS1981

Repairing high-temperature glazed tiles

Tetraethyl orthosilicate (TEOS) mixture fills chips and cracks in glazed tile surface. Filler is made by mixing hydrolyzed TEOS, silicon tetraboride powder, and pulverized tile material. Repaired tiles survived testing by intense acoustic emissions, arc jets, and intense heat radiation. Repair is reliable and rapid, performed in 1-1 1/2 hours with tile in any or orientation.

Ecord, G. M.↗

NASA NTRS1980

Burning characteristics and fiber retention of graphite/resin matrix composites

Graphite fiber reinforced resin matrix composites were subjected to controlled burning conditions to determine their burning characteristics and fiber retention properties. Small samples were burned with a natural gas fired torch to study the effects of fiber orientation and structural flaws such as holes and slits that were machined into the laminates. Larger laminate samples were burned in a modified heat release rate calorimeter. Unidirectional epoxy/graphite and polyimide/graphite composites and boron powder filled samples of each of the two composite systems were burn tested. The composites were exposed to a thermal radiation of 5.3 Btu/sq ft-sec in air. Samples of each of the unfilled composite were decomposed anaerobically in the calorimeter. Weight loss data were recorded for burning and decomposition times up to thirty-five minutes. The effects of fiber orientation, flaws, and boron filler additives to the resins were evaluated. A high char forming polyimide resin was no more effective in retaining graphite fibers than a low char forming epoxy resin when burned in air. Boron powder additions to both the polyimide and the epoxy resins stabilized the chars and effectively controlled the fiber release.

Bowles, K. J.↗

NASA NTRS1980

An assessment of the readiness of ablative materials for preflight application to the shuttle orbiter

The shuttle orbiter relies primarily on a reusable surface insulation (RSI) thermal protection system (TPS). The RSI is very efficient in its thermal performance; however, the RSI tile system has shown poor mechanical integrity. The state-of-the-art of the ablative TPS is reviewed, and an assessment made of the ablator's readiness for use on the shuttle orbiter. Unresolved technical issues with regard to the ablative TPS are identified. Short time, highly focused analytical and experimental programs were initiated to: (1) identify candidate ablation materials; (2) assess the data base for these materials; (3) evaluate the need and kind of waterproof coating; (4) calculate thermal and other stresses in an ablator tile; (5) identify an acceptable ablator/RSI tile joint filler; and (6) assess the sensitivity of the ablator to sequential heat pulses. Results from some of these programs are discussed.

Tompkins, S. S.↗

NASA NTRS1980

Effects of substrate deformation and sip thickness on tile/sip interface stresses for shuttle thermal protection

A nonlinear analysis was used to study the effects of substrate deformation characteristics and strain isolator pad (SIP) thickness on TILE/SIP interface stresses for the space shuttle thermal protection system. The configuration analyzed consisted of a 5.08 cm thick, 15.24 cm square tile with a 12.7 cm square SIP footprint bordered by a 1.27 cm wide filler bar and was subjected to forces and moments representative of a 20.7 kPa aerodynamic shock passing over the tile. The SIP stress deflection curves were obtained after a 69 kPa proof load and 100 cycles conditioning at 55 kPa. The TILE/SIP interface stresses increase over flat substrate values for zero to peak substrate deformation amplitudes up to 0.191 cm by up to a factor of nearly five depending on deformation amplitude, half wave length, and location. Stresses for a 0.23 cm thick SIP found to be up to 60 percent greater than for a 0.41 cm thick SIP for identical loads and substrate deformation characteristics. A simplified method was developed for approximating the substrate location which produces maximum TILE/SIP interface stresses.

Shore, C. P.↗

NASA NTRS1980

Hybridized polymer matrix composites

The extent to which graphite fibers are released from resin matrix composites that are exposed to fire and impact conditions was determined. Laboratory simulations of those conditions that could exist in the event of an aircraft crash and burn situation were evaluated. The effectiveness of various hybridizing concepts in preventing this release of graphite fibers were also evaluated. The baseline (i.e., unhybridized) laminates examined were prepared from commercially available graphite/epoxy, graphite/polyimide, and graphite/phenolic materials. Hybridizing concepts investigated included resin fillers, laminate coatings, resin blending, and mechanical interlocking of the graphite reinforcement. The baseline and hybridized laminates' mechanical properties, before and after isothermal and humidity aging, were also compared. It was found that a small amount of graphite fiber was released from the graphite/epoxy laminates during the burn and impact conditions used in this program. However, the extent to which the fibers were released is not considered a severe enough problem to preclude the use of graphite reinforced composites in civil aircraft structure. It also was found that several hybrid concepts eliminated this fiber release. Isothermal and humidity aging did not appear to alter the fiber release tendencies.

House, E. E.↗

NASA NTRS1980

Burning characteristics and fiber retention of graphite/resin matrix composites

Graphite fiber reinforced resin matrix composites were subjected to controlled burning conditions to determine their burning characteristics and fiber retention properties. Two types of burning equipment were used. Small samples were burned with a natural gas fired torch to study the effects of fiber orientation and structural flaws such as holes and slits that were machined into the laminates. Larger laminate samples were burned in a Heat Release Rate Calorimeter. Unidirectional epoxy/graphite and polyimide/graphite composites and boron powder filled samples of each of the two composite systems were burn tested and exposed to a thermal radiation. The effects of fiber orientation, flaws, and boron filler additives to the resins were evaluated. A high char forming polyimide resin was no more effective in retaining graphite fibers than a low char forming epoxy resin when burning in air.

Bowles, K. J.↗

NASA NTRS1980

Fiber release characteristics of graphite hybrid composites

The paper considers different material concepts that can be fabricated of hybridized composites which demonstrate improved graphite fiber retention capability in a severe fire without significant reduction to the composite properties. More than 30 panels were fabricated for mechanical and fire tests, the details and results of which are presented. Methods of composite hybridization investigated included the addition of oxidation resistant fillers to the resin, mechanically interlocking the graphite fibers by the use of woven fabrics, and the addition of glass fibers and glass additives designed to melt and fuse the graphite fibers together. It is concluded that a woven fabric with a serving of glass around each graphite tow is by far the superior of those evaluated: not only is there a coalescing effect in each graphite layer, but there is also a definite adhesion of each layer to its neighbor.

Henshaw, J.↗

NASA NTRS1980

Zero-length, slotted-lip inlet for subsonic military aircraft

Zero-length, slotted-lip inlet performance and associated fan blade stresses were determined during model tests using a 20-inch diameter fan simulator in the NASA-LeRC 9- by 15-foot low-speed wind tunnel. The model configuration variables consisted of inlet contraction ratio, slot width, circumferential extent of slot fillers, and length of a constant area section between the inlet throat and fan face. Inlet configurations having contraction ratios of 1.2 and 1.3 satisfied all critical low-speed inlet operating requirements for a fixed horizontal nacelle and tilt-nacelle-type subsonic V/STOL aircraft, respectively. Relative to a conventional axisymmetric tilt-nacelle inlet, the zero-length, slotted-lip inlet has a 27-percent smaller inlet lip contraction ratio, an 83-percent shorter total length, and a 5-percent smaller maximum cowl diameter.

Glasgow, E. R.↗

NASA NTRS1982

Fluxless Brazing of Large Structural Panels

Fluxless brazing is used in fabricating aluminum structural panels that withstand high internal pressure. Aluminum sheet of structural thickness with 4045 aluminum/silicon-braze-alloy cladding is brazed to corrugated "fin stock" having channels 0.001 inch (0.03mm) high by same width. Process is carried out in an inert (argon) atmosphere in a retort furnace. Filler bars are used in some channels to prevent fin stock from collapsing as pressure is applied.

Beuyukian, C. S.↗

NASA NTRS1982

Eddy-Current Meter Would Check Weld Wire Online

Simple Technique samples an entire spool of welding wire to test for contamination or unauthorized filler wire. Since unit monitors entire length of wire used in welding, completed welds need not be inspected individually. Technique would save time, avoiding human interface and production delays.

Bailey, G. R.↗