Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electric conductivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Hafnia-rich mixed oxide ceramics of the system HfO2-ZrO2-TiO2 for heaters and heat exchangers in electrothermal thrusters: The effects of titania on selected electrical and mechanical properties of Hafnia-rich mixed oxides in the system Hafnia-Zirconia-Titania, volume 1

A study of the effects of titania on selected properties of hafnia-rich mixed oxides in the system hafnia-zirconia-titania (HZT) was made in the region 5 to 20 mol percent titania. The studied properties included electrical conductivity, thermal expansion, and fracture strength and toughness. The effects of titania on the properties were studied for the reduced state as well as the oxidized state of the sintered mixed oxides. X-ray analysis showed that the materials were not always single phase. The oxidized compositions went from being monoclinic solid solutions at low titania additions to having three phases (two monoclinic and a titanate phase) at high additions of titania. The reduced compositions showed an increasing cubic phase presence mixed with the monoclinic phase as titania was added. The electrical conductivity increased with temperature at approximately 0.1 mhos/cm at 1700 C for all compositions. The thermal expansion coefficient decreased with increasing titania as did the monoclinic to tetragonal transformation temperature. The fracture strength of the oxidized bars tended to decrease with the addition of titania owing to the presence of the second phase titania. The fracture strength of the reduced bars exhibited a minimum corresponding to a two-phase region of monoclinic and cubic phases. When the second phases were suppressed, the titania tended to increase the fracture strength slightly in both the oxidized and reduced states. The fracture toughness followed similar trends.

Staszak, Paul Russell↗
NASA NTRS1999

Magnetic Damping of Solid Solution Semiconductor Alloys

The objective of this study is to: (1) experimentally test the validity of the modeling predictions applicable to the magnetic damping of convective flows in electrically conductive melts as this applies to the bulk growth of solid solution semiconducting materials; and (2) assess the effectiveness of steady magnetic fields in reducing the fluid flows occurring in these materials during processing. To achieve the objectives of this investigation, we are carrying out a comprehensive program in the Bridgman and floating-zone configurations using the solid solution alloy system Ge-Si. This alloy system has been studied extensively in environments that have not simultaneously included both low gravity and an applied magnetic field. Also, all compositions have a high electrical conductivity, and the materials parameters permit reasonable growth rates. An important supporting investigation is determining the role, if any, that thermoelectromagnetic convection (TEMC) plays during growth of these materials in a magnetic field. TEMC has significant implications for the deployment of a Magnetic Damping Furnace in space. This effect will be especially important in solid solutions where the growth interface is, in general, neither isothermal nor isoconcentrational. It could be important in single melting point materials, also, if faceting takes place producing a non-isothermal interface. In conclusion, magnetic fields up to 5 Tesla are sufficient to eliminate time-dependent convection in silicon floating zones and possibly Bridgman growth of Ge-Si alloys. In both cases, steady convection appears to be more significant for mass transport than diffusion, even at 5 Tesla in the geometries used here. These results are corroborated in both growth configurations by calculations.

Szofran, Frank R.↗
DOE OSTI2023

Electrospun Si and Si/C Fiber Anodes for Li-Ion Batteries

Due to structural changes in silicon during lithiation/delithiation, most Li-ion battery anodes containing silicon show rapid gravimetric capacity fade upon charge/discharge cycling. Herein, we report on a new Si powder anode in the form of electrospun fibers with only poly(acrylic acid) (PAA) binder and no electrically conductive carbon. The performance of this anode was contrasted to a fiber mat composed of Si powder, PAA binder, and a small amount of carbon powder. Fiber mat electrodes were evaluated in half-cells with a Li metal counter/reference electrode. Without the addition of conductive carbon, a stable capacity of about 1500 mAh/g (normalized to the total weight of the anode) was obtained at 1C for 50 charge/discharge cycles when the areal loading of silicon was 0.30 mgSi/cm2, whereas a capacity of 800 mAh/g was obtained when the Si loading was increased to ~1.0 mgSi/cm2. On a Si weight basis, these capacities correspond to >3500 mAh/gSi. The capacities were significantly higher than those found with a slurry-cast powdered Si anode with PAA binder. There was no change in fiber anode performance (gravimetric capacity and constant capacity with cycling) when a small amount of electrically conductive carbon was added to the electrospun fiber anodes when the Si loading was ≤1.0 mgSi/cm2.

Mondal, Abhishek N.↗
NASA NTRS2000

Thermophysical Properties of GRCop-84

The thermophysical properties and electrical resistivity of GRCop-84 (Cu - 8 at.% Cr-4 at.% Nb) were measured from cryogenic temperatures to near its melting point. The data were analyzed using weighted regression to determine the properties as a function of temperature and assign appropriate confidence intervals. The results showed that the thermal expansion of GRCop-84 was significantly lower than NARloy-Z (Cu-3 wt. % Ag-0.5 wt. % Zr), the currently used thrust cell liner material. The lower thermal expansion is expected to translate into lower thermally induced stresses and increases in thrust cell liner lives between 2X and 41X over NARloy-Z. The somewhat lower thermal conductivity of GRCop-84 can be offset by redesigning the liners to utilize its much greater mechanical properties. Optimized designs are not expected to suffer from the lower thermal conductivity. Electrical resistivity data, while not central to the primary application, show that GRCop-84 has potential for applications where a combination of good electrical conductivity and strength is required.

Ellis, David L.↗
NASA NTRS2003

Magnetic Flux Compression Experiments Using Plasma Armatures

Magnetic flux compression reaction chambers offer considerable promise for controlling the plasma flow associated with various micronuclear/chemical pulse propulsion and power schemes, primarily because they avoid thermalization with wall structures and permit multicycle operation modes. The major physical effects of concern are the diffusion of magnetic flux into the rapidly expanding plasma cloud and the development of Rayleigh-Taylor instabilities at the plasma surface, both of which can severely degrade reactor efficiency and lead to plasma-wall impact. A physical parameter of critical importance to these underlying magnetohydrodynamic (MHD) processes is the magnetic Reynolds number (R(sub m), the value of which depends upon the product of plasma electrical conductivity and velocity. Efficient flux compression requires R(sub m) less than 1, and a thorough understanding of MHD phenomena at high magnetic Reynolds numbers is essential to the reliable design and operation of practical reactors. As a means of improving this understanding, a simplified laboratory experiment has been constructed in which the plasma jet ejected from an ablative pulse plasma gun is used to investigate plasma armature interaction with magnetic fields. As a prelude to intensive study, exploratory experiments were carried out to quantify the magnetic Reynolds number characteristics of the plasma jet source. Jet velocity was deduced from time-of-flight measurements using optical probes, and electrical conductivity was measured using an inductive probing technique. Using air at 27-inHg vacuum, measured velocities approached 4.5 km/s and measured conductivities were in the range of 30 to 40 kS/m.

Turner, M. W.↗
NASA NTRS2003

Application of Core Dynamics Modeling to Core-Mantle Interactions

Observations have demonstrated that length of day (LOD) variation on decadal time scales results from exchange of axial angular momentum between the solid mantle and the core. There are in general four core-mantle interaction mechanisms that couple the core and the mantle. Of which, three have been suggested likely the dominant coupling mechanism for the decadal core-mantle angular momentum exchange, namely, gravitational core-mantle coupling arising from density anomalies in the mantle and in the core (including the inner core), the electromagnetic coupling arising from Lorentz force in the electrically conducting lower mantle (e.g. D-layer), and the topographic coupling arising from non-hydrostatic pressure acting on the core-mantle boundary (CMB) topography. In the past decades, most effort has been on estimating the coupling torques from surface geomagnetic observations (kinematic approach), which has provided insights on the core dynamical processes. In the meantime, it also creates questions and concerns on approximations in the studies that may invalidate the corresponding conclusions. The most serious problem is perhaps the approximations that are inconsistent with dynamical processes in the core, such as inconsistencies between the core surface flow beneath the CMB and the CMB topography, and that between the D-layer electric conductivity and the approximations on toroidal field at the CMB. These inconsistencies can only be addressed with numerical core dynamics modeling. In the past few years, we applied our MoSST (Modular, Scalable, Self-consistent and Three-dimensional) core dynamics model to study core-mantle interactions together with geodynamo simulation, aiming at assessing the effect of the dynamical inconsistencies in the kinematic studies on core-mantle coupling torques. We focus on topographic and electromagnetic core-mantle couplings and find that, for the topographic coupling, the consistency between the core flow and the CMB topography is critical for correct evaluation of the coupling torque.

Kuang, Weijia↗
DOE OSTI2020

Anomalous absorption of electromagnetic waves by 2D transition metal carbonitride Ti 3 CNT x (MXene)

Lightweight, ultrathin, and flexible electromagnetic interference (EMI) shielding materials are needed to protect electronic circuits and portable telecommunication devices and to eliminate cross-talk between devices and device components. Here, we show that a two-dimensional (2D) transition metal carbonitride, Ti 3 CNT x MXene, with a moderate electrical conductivity, provides a higher shielding effectiveness compared with more conductive Ti 3 C 2 T x or metal foils of the same thickness. This exceptional shielding performance of Ti 3 CNT x was achieved by thermal annealing and is attributed to an anomalously high absorption of electromagnetic waves in its layered, metamaterial-like structure. These results provide guidance for designing advanced EMI shielding materials but also highlight the need for exploring fundamental mechanisms behind interaction of electromagnetic waves with 2D materials.

Science & Technology - Other Topics↗
NASA NTRSDate not supplied

Laboratory Radar Measurements in Support of the NASA Orbital Debris Program Office’s Size Estimation Model

The NASA Orbital Debris Program Office (ODPO) relies on ground-based radar measurements from both the Haystack Ultrawideband Satellite Imaging Radar (HUSIR) and the Goldstone Solar System Radar (Goldstone) to characterize mm to cm debris population in low Earth orbit (LEO). Radar measurements help characterize the size of orbital debris objects, particularly fragmentation debris. However, debris size is not directly measured by radar but inferred from the measured radar cross section (RCS) which depends on several parameters in addition to physical size including electrical conductivity and polarization. To interpret the observed RCS of orbital debris objects detected by radar measurements as physical sizes, NASA uses an empirical size estimation model (SEM) based on laboratory RCS measurements of breakup fragments generated during hypervelocity impact tests as well as some pieces of non-impact-generated “artificial” debris-like objects expected to be representative of the debris population. Since the development of the ODPO SEM, many new materials have been introduced to spacecraft construction. Consequently, ODPO plans to update the radar SEM based on planned laboratory RCS measurements of debris fragments from DebriSat, a ground-based hypervelocity impact experiment conducted in 2014 that consisted of a high-fidelity spacecraft model characteristic of a modern LEO spacecraft. Prior to measuring DebriSat fragments, a set of calibration targets with well-defined geometries and material compositions were measured at The Ohio State University’s ElectroScience Laboratory (OSU-ESL) compact radar range. These calibration measurements help to validate, and understand any limitations of, laboratory measurements of RCS. Calibration targets include idealizations of typical shape categories seen in DebriSat fragments such as nuggets, flat plates, and cylinders. As with DebriSat, calibration target materials were chosen to represent typical modern-day spacecraft components and include stainless steel, aluminum, printed circuit board (PCB) substrate, and carbon fiber-reinforced polymer (CFRP). These materials also represent a wide range of electrical conductivities, which strongly influences measured RCS and inferred target size. The RCS calibration measurements were collected over a frequency sweep from 2 to 18 GHz and stepping through different azimuth angles from 0 to 360 degrees at an elevation of 0 degrees. A second set of calibration measurements is in work consisting of more complex shapes such as bent rods and plates as well as different mounting options including epoxy and a 3D printed holder. These further measurements along with our initial calibration set will inform selection of representative DebriSat fragments for laboratory RCS measurements that will contribute to the planned update to the ODPO radar SEM. An appropriate subset of both the radar calibration and DebriSat samples will also be measured in the ODPO Optical Measurements Center to cross-calibrate size estimates over these different wavelength regimes.

Radar↗
NASA NTRS1990

The assessment of metal fiber reinforced polymeric composites

Because of their low cost, excellent electrical conductivity, high specific strength (strength/density), and high specific modulus (modulus/density) short metal fiber reinforced composites have enjoyed a widespread use in many critical applications such as automotive industry, aircraft manufacturing, national defense, and space technology. However, little data has been found in the study of short metal fibrous composites. Optimum fiber concentration in a resin matrix and fiber aspect ratio (length-to-diameter ratio) are often not available to a user. Stress concentration at short fiber ends is the other concern when the composite is applied to a load-bearing application. Fracture in such composites where the damage will be initiated or accumulated is usually difficult to be determined. An experimental investigation is therefore carefully designed and undertaken to systematically evaluate the mechanical properties as well as electrical properties. Inconel 601 (nickel based) metal fiber with a diameter of eight microns is used to reinforce commercially available thermoset polyester resin. Mechanical testing such as tensile, impact, and flexure tests along with electrical conductivity measurements is conducted to study the feasibility of using such composites. The advantages and limitations of applying chopped metal fiber reinforced polymeric composites are also discussed.

Chung, Wenchiang R.↗
DOE OSTI2024

Design Optimization and Measurement Uncertainty of an Electromagnetic Level Sensor for Liquid Metal Reactors

Here, this article describes the design and operation of a prototype mutual inductance level sensor (MILS) and the development and validation of a finite-element analysis (FEA) model describing its behavior. The MILS was designed for use in liquid sodium up to temperatures of 650 °C in the Mechanisms Engineering Test Loop (METL) at Argonne National Laboratory (ANL). Preliminary testing was performed in a room temperature test stand with aluminum acting as an analog for the sodium to better understand sensor performance and provide accurate code validation data. This experimental data, along with material properties found in literature, were used to validate an FEA model in ANSYS Maxwell. The validated ANSYS Maxwell model was used to examine the performance of the MILS in various environments and under various operating conditions. Simulations suggest the following: The MILS will perform adequately in liquid sodium and liquid lead at temperatures up to 650 °C . The temperature dependence of electrical conductivity imposes a temperature dependence on the sensor that requires proper compensation. The MILS signal sensitivity is maximized when mutual inductance between sensor coils is maximized, and sensor geometry should be selected to account for this factor. The operating frequency of the MILS can be optimized and is dependent on process fluid material, operating temperature, and materials/geometry of sensor system. Finally, the use of a stainless-steel isolating thimble does not adversely affect the sensor signal. The primary sources of error for this MILS system are the accuracy of the calibration standard against which the sensor is calibrated, and the temperature dependence of the sensor. This work contains all the necessary details to recreate the FEA model and results. This model can be used to optimize the performance of a MILS in any operating environment to read any electrically conductive working fluid.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1971

Some experimental observations on circulating currents in a crossed field plasma accelerator

Experiments on a thermally ionized argon plasma suggest that applying a Lorentz force by means of orthogonal electric and magnetic fields to an electrically conducting fluid flow imposes necessary but not sufficient conditions for acceleration. There are, in fact, many combinations of current and magnetic field which cause decelerations of the fluid. The deceleration arises from a retarding force which may be larger than the applied Lorentz force. The retarding force causing the deceleration is a consequence of currents circulating completely within the fluid. These currents arise from differences in velocity between the central and wall regions of the duct which interact with the imposed magnetic field to produce differences in induced voltages. The observed physical effects of the circulating currents cause a loss in velocity in the central region of the duct, an increase in thermal energy in the sidewall region, and little change in thermal energy near the electrode wall region. For similar velocity profiles, the adverse effects appear to be related to the product of electrical conductivity and velocity, and performance as an accelerator appears to be controlled by the Hoffman loading parameter (i.e., the ratio of the applied to the induced currents).

Jedlicka, J.↗
DOE OSTI2020

Highly-Active and Contaminant-Tolerant Cathodes for Durable Solid Oxide Fuel Cells (Final Report)

The objective of this project is to investigate the fundamental degradation methods occurring in solid oxide fuel cell (SOFC) cathodes when exposed to chromium and carbon dioxide contamination and to rationally design alkaline earth-based catalysts to increase stability and tolerance to contaminate poisoning. With a mechanistic and fundamental understanding of the degradation methods, advanced catalytic surface modifications can be applied to reduce degradation. The specific technical objectives are: (1) To identify/develop new catalysts (alkaline-earth based-) that are compatible chemically with the state-of-the-art cathode materials at high temperatures required for fabrication and with contaminates commonly encountered under operating conditions; (2) To improve the infiltration process for optimal control of the thickness, composition, and uniformity of the catalyst coatings; (3) To evaluate the electro-catalytic activity toward ORR of the chemically-stable materials when exposed to different types of contaminants using electrical conductivity relaxation measurements on bar samples and performance evaluation of catalyst-infiltrated cathodes; (4) To unravel the contamination-tolerant mechanisms of the new catalyst coatings under realistic environmental conditions (with different types of contaminants) using powerful in situ and in operando characterization techniques performed on model cells with thin-film/pattern electrodes, as guided by modeling and simulation; (5) To establish scientific basis for rational design of new catalysts of high tolerance to contaminants; (6) To validate the long term stability of modified LSCF cathodes in commercially available cells/stacks under ROC. Alkaline earth-based catalysts have been systematically explored and tested under various contamination conditions. BaCoO 3-δ (BCO) was shown to produce the best catalytic activity enhancement as well as stability in a variety of contaminating conditions, including CO 2 and chromium. The microstructural evolution was investigated with SEM, EDS, and Raman spectroscopy, showing the BCO catalyst prevents the formation of insulating SrCrO 4 by forming electrically conductive BaCrO 4 . Electrochemical relaxation measurements determined the BCO catalyst coatings increased the surface diffusion coefficient but did not significantly affect the diffusion coefficient and determined an optimum surface modification layer of 100 nm. A novel Ba 0.9 Co 0.7 Fe 0.2 Nb 0.1 O x (BCFN) catalyst was also shown to have excellent stability in chromium containing atmospheres. A novel surface sol-gel (SSG) surface modification, which offers superior thickness and compositional control, was applied to SOFCs to produce BaO catalyst coatings. SSG BaO coatings were shown to produce conformal coatings on the electrode surface, greatly increasing stability in chromium containing atmospheres. An atomic level mechanistic approach was applied to investigate the stability of PrBa 0.8 Ca 0.2 Co2O 5+δ (PBCC) with respect to a variety of common contaminants, demonstrating thermodynamically its superior stability in CO2 containing atmospheres. Finally, the best catalyst coatings demonstrated in this project, BCO and PBCC, were applied to full cells which demonstrated superior stability for over 300 hours in CO 2 and Cr atmospheres.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Highly-Active and Contaminant-Tolerant Cathodes for Durable Solid Oxide Fuel Cells

The objective of this project is to investigate the fundamental degradation methods occurring in solid oxide fuel cell (SOFC) cathodes when exposed to chromium and carbon dioxide contamination and to rationally design alkaline earth-based catalysts to increase stability and tolerance to contaminate poisoning. With a mechanistic and fundamental understanding of the degradation methods, advanced catalytic surface modifications can be applied to reduce degradation. The specific technical objectives are: (1) To identify/develop new catalysts (alkaline-earth based-) that are compatible chemically with the state-of-the-art cathode materials at high temperatures required for fabrication and with contaminates commonly encountered under operating conditions; (2) To improve the infiltration process for optimal control of the thickness, composition, and uniformity of the catalyst coatings; (3) To evaluate the electro-catalytic activity toward ORR of the chemically-stable materials when exposed to different types of contaminants using electrical conductivity relaxation measurements on bar samples and performance evaluation of catalyst-infiltrated cathodes; (4) To unravel the contamination-tolerant mechanisms of the new catalyst coatings under realistic environmental conditions (with different types of contaminants) using powerful in situ and in operando characterization techniques performed on model cells with thin-film/pattern electrodes, as guided by modeling and simulation; (5) To establish scientific basis for rational design of new catalysts of high tolerance to contaminants; (6) To validate the long term stability of modified LSCF cathodes in commercially available cells/stacks under ROC. Alkaline earth-based catalysts have been systematically explored and tested under various contamination conditions. BaCoO 3-δ (BCO) was shown to produce the best catalytic activity enhancement as well as stability in a variety of contaminating conditions, including CO 2 and chromium. The microstructural evolution was investigated with SEM, EDS, and Raman spectroscopy, showing the BCO catalyst prevents the formation of insulating SrCrO 4 by forming electrically conductive BaCrO 4 . Electrochemical relaxation measurements determined the BCO catalyst coatings increased the surface diffusion coefficient but did not significantly affect the diffusion coefficient and determined an optimum surface modification layer of 100 nm. A novel Ba 0.9 Co 0.7 Fe 0.2 Nb 0.1 O x (BCFN) catalyst was also shown to have excellent stability in chromium containing atmospheres. A novel surface sol-gel (SSG) surface modification, which offers superior thickness and compositional control, was applied to SOFCs to produce BaO catalyst coatings. SSG BaO coatings were shown to produce conformal coatings on the electrode surface, greatly4 increasing stability in chromium containing atmospheres. An atomic level mechanistic approach was applied to investigate the stability of PrBa 0.8 Ca 0.2 Co 2 O 5+δ (PBCC) with respect to a variety of common contaminants, demonstrating thermodynamically its superior stability in CO 2 containing atmospheres. Finally, the best catalyst coatings demonstrated in this project, BCO and PBCC, were applied to full cells which demonstrated superior stability for over 300 hours in CO 2 and Cr atmospheres.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Highly-Active and Contaminant-Tolerant Cathodes for Durable Solid Oxide Fuel Cells

The objective of this project is to investigate the fundamental degradation methods occurring in solid oxide fuel cell (SOFC) cathodes when exposed to chromium and carbon dioxide contamination and to rationally design alkaline earth-based catalysts to increase stability and tolerance to contaminate poisoning. With a mechanistic and fundamental understanding of the degradation methods, advanced catalytic surface modifications can be applied to reduce degradation. The specific technical objectives are: (1) To identify/develop new catalysts (alkaline-earth based-) that are compatible chemically with the state-of-the-art cathode materials at high temperatures required for fabrication and with contaminates commonly encountered under operating conditions; (2) To improve the infiltration process for optimal control of the thickness, composition, and uniformity of the catalyst coatings; (3) To evaluate the electro-catalytic activity toward ORR of the chemically-stable materials when exposed to different types of contaminants using electrical conductivity relaxation measurements on bar samples and performance evaluation of catalyst-infiltrated cathodes; (4) To unravel the contamination-tolerant mechanisms of the new catalyst coatings under realistic environmental conditions (with different types of contaminants) using powerful in situ and in operando characterization techniques performed on model cells with thin-film/pattern electrodes, as guided by modeling and simulation; (5) To establish scientific basis for rational design of new catalysts of high tolerance to contaminants; (6) To validate the long term stability of modified LSCF cathodes in commercially available cells/stacks under ROC. Alkaline earth-based catalysts have been systematically explored and tested under various contamination conditions. BaCoO 3-δ (BCO) was shown to produce the best catalytic activity enhancement as well as stability in a variety of contaminating conditions, including CO 2 and chromium. The microstructural evolution was investigated with SEM, EDS, and Raman spectroscopy, showing the BCO catalyst prevents the formation of insulating SrCrO 4 by forming electrically conductive BaCrO 4 . Electrochemical relaxation measurements determined the BCO catalyst coatings increased the surface diffusion coefficient but did not significantly affect the diffusion coefficient and determined an optimum surface modification layer of 100 nm. A novel Ba 0.9 Co 0.7 Fe 0.2 Nb 0.1 O x (BCFN) catalyst was also shown to have excellent stability in chromium containing atmospheres. A novel surface sol-gel (SSG) surface modification, which offers superior thickness and compositional control, was applied to SOFCs to produce BaO catalyst coatings. SSG BaO coatings were shown to produce conformal coatings on the electrode surface, greatly 4 increasing stability in chromium containing atmospheres. An atomic level mechanistic approach was applied to investigate the stability of PrBa 0.8 Ca 0.2 Co 2 O 5+δ (PBCC) with respect to a variety of common contaminants, demonstrating thermodynamically its superior stability in CO 2 containing atmospheres. Finally, the best catalyst coatings demonstrated in this project, BCO and PBCC, were applied to full cells which demonstrated superior stability for over 300 hours in CO 2 and Cr atmospheres

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

Observation of the Electromagnetic Field Effect via Charge-Dependent Directed Flow in Heavy-Ion Collisions at the Relativistic Heavy Ion Collider

The deconfined quark-gluon plasma (QGP) created in relativistic heavy-ion collisions enables the exploration of the fundamental properties of matter under extreme conditions. Noncentral collisions can produce strong magnetic fields on the order of 10 18 G , which offers a probe into the electrical conductivity of the QGP. In particular, quarks and antiquarks carry opposite charges and receive contrary electromagnetic forces that alter their momenta. This phenomenon can be manifested in the collective motion of final-state particles, specifically in the rapidity-odd directed flow, denoted as v 1 ( y ) . Here, we present the charge-dependent measurements of d v 1 / d y near midrapidities for π ± , K ± , and p ( p ¯ ) in Au + Au and isobar ( Ru 44 96 + Ru 44 96 and Zr 40 96 + Zr 40 96 ) collisions at s NN = 200 GeV , and in Au + Au collisions at 27 GeV, recorded by the STAR detector at the Relativistic Heavy Ion Collider. The combined dependence of the v 1 signal on collision system, particle species, and collision centrality can be qualitatively and semiquantitatively understood as several effects on constituent quarks. While the results in central events can be explained by the u and d quarks transported from initial-state nuclei, those in peripheral events reveal the impacts of the electromagnetic field on the QGP. Our data put valuable constraints on the electrical conductivity of the QGP in theoretical calculations. Published by the American Physical Society 2024

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRSDate not supplied

Characterization of Novel Spacecraft Materials aboard the Materials International Space Station Experiment-Flight Facility (Preliminary Results)

This work will encompass the preflight characterization of 15 novel and heritage materials currently under observation on the Materials International Space Station Experiment-Flight Facility (MISSE-FF). MISSE-FF has been upgraded to perform active reflectance measurements of the materials. Images taken in RGB/IR colors are compared to results from an extensive ground testing campaign to obtain quantitative on-orbit material evolution data. Identical materials samples are to be flown on the ram, wake, and zenith faces of MISSE-FF, enabling deconvolution of the energetic electron, proton, atomic oxygen, and ultraviolet damage pathways. Energy deposition from the space environment leads to chemical changes in the material that in turn alter the optical properties. The same chemical damage that manifests as changes in optical reflectance and absorptance also leads to changes in myriad physical properties such as mechanical strength, electrical conductivity, and chemical reactivity. Therefore, flight materials are able to be characterized based on their unique reflectance spectra by comparing on-orbit measurements of optical reflectance with extensive terrestrial experiments, which help to correlate changes in reflectance with respect to changes in other material properties. The MISSE program has been a part of the International Space Station National Laboratory for many years and has been instrumental in understanding space weather modification of material properties. However, MISSE-FF has been limited to passive experiments with only pre/post flight material studies possible. In advance of the MISSE-16 experiment, the flight facility has received a major upgrade to provide daily spectral observations by way of a RGB/IR camera and a tunable light source. The MISSE-16 mission launched in February 2022 and carries 15 material samples for 6 months of the low Earth orbital exposure. Identical materials samples are to be flown on the ram, wake, and zenith faces of MISSE-FF, enabling deconvolution of the energetic electron, proton, atomic oxygen, and ultraviolet damage pathways. This paper discusses the MISSE-16 experiment, highlights the first use of the facility upgrades, and presents results from the extensive preflight material characterization that includes directional hemispherical reflectance, bidirectional reflectance, AFM, SEM, and electrical conductivity. Additionally, data showing the modification of these properties by ground-based exposure to space-like electron and atomic oxygen flux will be discussed. Finally, updates on deployment and initial check-out of the experiment on MISSE-FF will be presented. It is the ultimate goal of this program to provide validation for the development of ground based space weather simulation facilities and techniques.

Ryan Hoffman↗
DOE OSTI2022

Robust hierarchical three dimensional nickel cobalt tungstate-MXene nanocomposite for high performance symmetric coin cell supercapacitors

Design of rational electrode materials with hierarchically structured pseudocapacitive materials has been identified as a successful strategy for revamping the electrochemical characteristics of supercapacitors. However, the simultaneous assurance of strong electrical conductivity and higher specific capacitance via a simple and cost-effective synthesis protocol is of concern today. In this work, Ni-CoWO 4 incorporated MXene nanocomposite has been successfully prepared by a facile hydrothermal process. The structure, morphology, stoichiometry, and chemical characterization of the prepared Ni-CoWO 4 , Ti 3 C 2 T x , and Ni-CoWO4@MXene nanocomposite were explored extensively. MXene demonstrated a layered 2D nanoscale structure whereas pure Ni-CoWO 4 was composed of spherical nanoparticles. The composite Ni-CoWO 4 @MXene revealed the morphology of spherical Ni-CoWO 4 nanoparticles decorated on MXene sheets. Furthermore, a series of electrochemical characterizations illustrated the contribution of the delightful morphology of Ni-CoWO 4 @MXene composite to excellent electrochemistry. The resultant Ni-CoWO 4 @MXene electrode exhibited high specific capacitance of 582 Fg -1 at 1 A g -1 and 93.5 % capacitance retention over the 10,000 cycles., which is higher than that of the individual counterparts Ni-CoWO 4 and MXene. The excellent electrochemical performance of Ni-CoWO 4 @MXene is attributed to the synergistic interaction between Ni-CoWO4 nanoparticles and nanolayered MXene that may create new active sites that enhanced the charge transfer, charge/discharge kinetics and the electrical conductivity. Significantly, the unique Ni-CoWO 4 @MXene supercapacitor prototype delivered a higher energy density of 85.7 Wh kg -1 and power density of 0.85 kW kg -1 establishing its superiority over other Cosingle bondW based supercapacitors. A theoretical study was also performed to correlate the improved charge storage capacity of the prepared Ni-CoWO 4 @MXene composite.

25 ENERGY STORAGE↗