Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dimer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Inefficient Growth of Refractory Grains: Implications for Grains in the Solar Nebula

Introduction: We report the results of a sounding rocket experiment in which SiO nucleation and growth in an argon atmosphere was observed in microgravity starting from a vapor generated by evaporation of waterglass deposited on a heated Ta wire. The temperature and pressure at the point of nucleation was determined using a double wavelength Mach–Zehnder-type interferometer. The particle composition and grain size distribution were measured after payload recovery using a Transmission Electron Microscope (TEM; JEM-2100F. JEOL Ltd., Tokyo). The results were analyzed using Modified Classical Nucleation Theory (MCNT)[1]. We report a measurement of the SiO-silicate grain sticking coefficient of 0.016, indicating very inefficient grain growth from the vapor. In other words, for every 100 SiO molecules that collide with a growing grain only one to two are captured. In the only two previous studies of the growth of solid particles from the gas phase the calculated sticking coefficients were much lower. For zinc atoms colliding with zinc crystals only three out of 100,000 collisions resulted in grain growth [2]. Iron atoms colliding with growing iron particles similarly showed an efficiency of ~0.00002 [3]. For zinc, we can explain inefficient growth due to the difficulty of the colliding atom coming upon a vacancy in the growing crystal lattice before it evaporates from the grain surface. The much higher sticking coefficient of SiO molecules on silica grains is reasonable because the silica grains are highly amorphous or glassy and therefore provide a much higher defect density where SiO molecules can be captured into the grains. In the case of similar Fe experiment, the critical cluster was the dimer. In this case the forming dimer returns to the vapor phase by dissociation due to the excess energy from the formation of the Fe-Fe bond.

Joseph A Nuth↗

Selective Detection of Diglycolamide Diastereomers By Metal-Ligand Cluster Formation

Introduction (120 words): Differentiation of isomers using mass spectrometry is a challenge, as these species tend to produce ions of identical mass-to-charge ratio. Therefore, separation with mass spectrometry must rely on chemical differences between isomeric species. Separation of stereoisomers is especially challenging, as these species often have very similar chemistry. However, recent investigations of the solvent extraction behavior of diastereomers of diglycolamide molecules have shown that different stereoisomers can have significantly different lanthanide extraction efficiencies. These studies showed that the R,S stereoisomer of 2,2'-oxybis(N,N-dioctylpropanamide efficiently extracts lanthanides, while the S,S stereoisomer does not. Thus, gas-phase metal complexation may provide a pathway for differentiating these species using mass spectrometry. Methods (120 words): Europium, samarium, and holmium clusters with the R,S, and the S,S diastereomers of 2,2'-oxybis(N,N-didecylpropanamide (trivially tetradecyl diglycolamide, or mTDDGA) were generated in gas-phase using the electrospray ionization source of a Bruker (Billerica, MA, USA) micrOTOF-Q II quadrupole time-of-flight mass spectrometer. Solutions of aqueous lanthanide nitrate and diglycolamide ligands in 2-propanol were added to 50%:50% by volume acetonitrile:2-propanol to generate the spray solutions. Ligand concentration was maintained at approximately 6 µM, while lanthanide concentration was maintained at either 6 µM or 30 µM . High resolution, high mass accuracy spectra were recorded using the time-of-flight. Mass accuracy was ensured using external calibration with Agilent (Santa Clara, CA, USA) ESI-L Low Concentration tuning mix. Preliminary data (300 words): Electrospray of solutions containing only R,S-mTDDGA or S,S-m-TDDGA yield abundant peaks at m/z= 721.7, corresponding to [mTDDGA+H]+1, m/z = 743.7, corresponding to [mTDDGA+Na]+1, and m/z = 1464.4, corresponding to the sodium-bound dimer, [Na(mTDDGA)2]+1. Spray of solutions containing 6 µM europium (Eu) with 3 µM R,S-mTDDGA produced an abundant cluster ion with an isotopic envelope centered at m/z=772.0, corresponding to [Eu(R,S-mTDDGA)3]3+. Europium-containing cluster ions with isotopic envelopes apexing at m/z = 1012.3 and 1189.0 correspond to the [Eu(R,S-mTDDGA)4]3+ and [Eu(R,S-mTDDGA)5]3+ cluster ions, respectively. Protonated and sodiated R,S-mTDDGA are present as well, along with the sodium-bound dimer. In contrast, spray of solutions containing 6 µM europium (Eu) with 3 µM S,S-mTDDGA diastereomer yielded only protonated and sodiated ligand ions; no Eu- S,S-mTDDGA ions were present. This mirrors the solution-phase behavior, where the S,S diestereomer extracts lanthanides with significantly less efficiency than the R,S diestereomer. Experiments with holmium and samarium yielded the same results. Increasing the lanthanide concentration to 30 µM resulted in limited formation of lanthanide-S,S-mTDDGA clusters. However, the abundance of the [Ln(S,S-mTDDGA)3]3+ clusters remained low compared to the abundance of the protonated and sodiated ligand. Additionally, the abundance of the [Ln(R,S-mTDDGA)3]3+ cluster ion was significantly higher than that of the protonated and sodiated ligand in experiments with spray solutions containing 30 µM lanthanide with R,S-mTDDA, supporting the hypothesis that R,S-mTDDGA has a higher intrinsic affinity for the lanthanides than S,S-mTDDGA. Thus, the intrinsic complexation with lanthanides appears to offer a route to differentiate diglycolamide diestereomers in the gas-phase. Novelty (20): Stereoisomers can be differentiated in the gas phase by exploitation of differences in metal complexation chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of alternate encounter assemblies of SARS-CoV-2 main protease

The assembly of two monomeric constructs spanning segments 1-199 (MPro 1-199 ) and 10-306 (MPro 10-306 ) of SARS-CoV-2 main protease (MPro) was examined to assess the existence of a transient heterodimer intermediate in the N-terminal autoprocessing pathway of MPro model precursor. Together, they form a heterodimer population accompanied by a 13-fold increase in catalytic activity. Addition of inhibitor GC373 to the proteins increases the activity further by ~7-fold with a 1:1 complex and higher order assemblies approaching 1:2 and 2:2 molecules of MPro 1-199 and MPro 10-306 detectable by analytical ultracentrifugation and native mass estimation by light scattering. Assemblies larger than a heterodimer (1:1) are discussed in terms of alternate pathways of domain III association, either through switching the location of helix 201 to 214 onto a second helical domain of MPro 10-306 and vice versa or direct interdomain III contacts like that of the native dimer, based on known structures and AlphaFold 3 prediction, respectively. At a constant concentration of MPro 1-199 with molar excess of GC373, the rate of substrate hydrolysis displays first order dependency on the MPro 10-306 concentration and vice versa. An equimolar composition of the two proteins with excess GC373 exhibits half-maximal activity at ~6 μM MPro 1-199 . Catalytic activity arises primarily from MPro 1-199 and is dependent on the interface interactions involving the N-finger residues 1 to 9 of MPro 1-199 and E290 of MPro 10-306 . Importantly, our results confirm that a single N-finger region with its associated intersubunit contacts is sufficient to form a heterodimeric MPro intermediate with enhanced catalytic activity.

60 APPLIED LIFE SCIENCES↗

Olefin Coupling Catalyzed by (Pybox)Os Complexes via Osmacyclopentane Intermediates: Comparison with Isoelectronic (Phebox)Ir

(Pybox)Os is found to catalyze alkene hydrovinylation, effecting the dimerization of ethylene, tail-to-tail coupling of propene and 1-butene, and cross-coupling of ethylene with higher α-olefins. This reactivity contrasts with the previously reported dehydrogenative coupling of ethylene to give butadiene catalyzed by the isoelectronic fragment (Phebox)Ir. The reaction mechanism was investigated through computational and experimental means. Both the Os- and Ir-catalyzed reactions proceed through a [2 + 2 + 1] cyclization of the corresponding bis-olefin complex to yield an experimentally observed metallacyclopentane intermediate. In both cases, the metallacyclopentane undergoes β- H elimination, via a dechelated κ 2 -pincer-ligated intermediate, to yield a σ−π-but-3-enyl hydride complex or derivative. Both the greater reactivity and the distinct chemoselectivity of the Os system relative to the Ir system are attributable to C−H reductive elimination by the σ−π-but-3-enyl hydride having a barrier for Os much lower than that for Ir. This lower barrier to C−H elimination for Os is unexpected given that the thermodynamic driving force for elimination is much less for Os than for Ir. Computational studies of model complexes were conducted, comparing (Pybox)Os(L)(CH 3 )(H) with the isoelectronic (Phebox)Ir(L)(CH 3 )(H). The results indicate that the more facile kinetics with Os relative to Ir may be general for C−H elimination from six-coordinate d 6 complexes of the two metals, as well as for the microscopic reverse, i.e., C−H addition to the corresponding four-coordinate d 8 species.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Role of Magnetic Defects in Tuning Ground States of Magnetic Topological Insulators

Abstract Magnetic defects play an important, but poorly understood, role in magnetic topological insulators (TIs). For example, topological surface transport and bulk magnetic properties are controlled by magnetic defects in Bi 2 Se 3 ‐based dilute ferromagnetic (FM) TIs and MnBi 2 Te 4 (MBT)‐based antiferromagnetic (AFM) TIs. Despite its nascent ferromagnetism, the inelastic neutron scattering data show that a fraction of the Mn defects in Sb 2 Te 3 form strong AFM dimer singlets within a quintuple block. The AFM superexchange coupling occurs via Mn–Te–Mn linear bonds and is identical to the AFM coupling between antisite defects and the FM Mn layer in MBT, establishing common interactions in the two materials classes. It is also found that the FM correlations in (Sb 1− x Mn x ) 2 Te 3 are likely driven by magnetic defects in adjacent quintuple blocks across the van der Waals gap. In addition to providing answers to long‐standing questions about the evolution of FM order in dilute TI, these results also show that the evolution of global magnetic order from AFM to FM in Sb‐substituted MBT is controlled by defect engineering of the intrablock and interblock coupling.

36 MATERIALS SCIENCE↗

A Heteromeric Carboxylic Acid Based Single-Crystalline Crosslinked Organic Framework

The development of large pore single-crystalline covalently linked organic frameworks is critical in revealing the detailed structure-property relationship with substrates. One emergent approach is to photo-crosslink hydrogen-bonded molecular crystals. Introducing complementary hydrogen-bonded carboxylic acid building blocks is promising to construct large pore networks, but these molecules often form interpenetrated networks or non-porous solids. In this report we introduced heteromeric carboxylic acid dimers to construct a non-interpenetrated molecular crystal. Crosslinking this crystal precursor with dithiols afforded a large pore single-crystalline hydrogen-bonded crosslinked organic framework H C OF-101. X-ray diffraction analysis revealed H C OF-101 as an interlayer connected hexagonal network, which possesses flexible linkages and large porous channels to host a hydrazone photoswitch. Multicycle Z/E-isomerization of the hydrazone took place reversibly within H C OF-101, showcasing the potential use of H C OF-101 for optical information storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Crosslinked Ionic Organic Framework for Efficient Iodine and Iodide Remediation in Water

Iodine is widely used as an antimicrobial reagent for water disinfection in the wilderness and outer space, but residual iodine and iodide need to be removed for health reasons. Currently, it is challenging to remove low concentrations of iodine and iodide in water (~5 ppm). Furthermore, the remediation of iodine and iodide across a broad temperature range (up to 90 °C) has not previously been investigated. In this work, we report a nitrate dimer-directed synthesis of a single-crystalline ionic hydrogen-bonded crosslinked organic framework (HCOF-7). HCOF-7 removes iodine and iodide species in water efficiently through halogen bonding and anion exchange, reducing the total iodine concentration to 0.22 ppm at room temperature. Packed HCOF-7 columns were employed for iodine/iodide breakthrough experiments between 23 and 90 °C, and large breakthrough volumes were recorded (≥18.3 L/g). Finally, the high iodine/iodide removal benchmarks recorded under practical conditions make HCOF-7 a promising adsorbent for water treatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Saddle point search with dynamic active volume

Sampling potential energy surface (PES) is critical for many problems in materials science, chemistry, physics, and biology and requires highly efficient saddle point searches (SPS). In the study, we introduce the concept of dynamic active volume (DAV) in addition to the active volume in self-evolving atomistic kinetic Monte Carlo (SEAKMC). The DAV method has further reduced the dimensionality of the PES at the elevation stage of a SPS. At the subsequent converging stage, the dynamic boundary in DAV is lifted to allow the system to converge to the right location of a saddle point. Coupled with the dimer method, the DAV method not only significantly reduces the time cost for a given search attempt, but also dramatically increases the probability of finding relevant saddle points for PES sampling. Further, a Python software package within the framework SEAKMC (SEAKMC_py) with the DAV method has been developed.

36 MATERIALS SCIENCE↗

Mechanism of $\mathrm{E}$-bridge formation by various $\mathrm{PAH}$ molecules: A theoretical study

Potential energy surfaces (PES) for dimerization of acepyrene-pyrene, aceanthracene-anthracene, and acenaphthalene-naphthalene were computed by the G3(MP2,CC) and ONIOM2(G3(MP2,CC):B3LYP/6-31G(d)) methods. Close agreement of relative energies of corresponding species along reaction paths for different reactions was found suggesting that the PES for E-bridge formation depends weakly on the number of rings in the interacting monomers. Our results indicate that the reaction rate is controlled by the dynamics of the initial collision, which may depend on the monomer size. The ONIOM approach is proposed as an accurate tool for calculations of PES in large PAH systems being more reliable than various DFT methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Low-symmetry polymorph of GaP upends bonding paradigms of metallic high-pressure III–V compounds

Here, the pressure-induced polymorphism of binary octet compounds has long been considered a settled problem although the possible atomic disordering of some phases remains a puzzling observation. Taking GaP as a case study, we conclude, through x-ray microdiffraction and first-principles calculations, that its high-pressure metallic phase (previously reported as being disordered) adopts in fact an ordered base-centered monoclinic structure previously unknown in this class of compounds. The formation of layered patterns with variable degrees of interlayer dimerization, as observed in GaP, marks a paradigm shift of our understanding of ordering in octet high-pressure phases which calls for a more extensive re-examination. A rich polymorphism with fine tuning of chemical and physical properties can be envisioned.

36 MATERIALS SCIENCE↗

Pathway discovery and engineering for cleavage of a β-1 lignin-derived biaryl compound

Lignin biosynthesis typically results in a polymer with several inter-monomer bond linkages, and the heterogeneity of linkages presents a challenge for depolymerization processes. While several enzyme classes have been shown to cleave common dimer linkages in lignin, the pathway of bacterial β-1 spirodienone linkage cleavage has not been elucidated. In this study, we identified a pathway for cleavage of 1,2-diguaiacylpropane-1,3-diol (DGPD), a β-1 linked biaryl representative of a ring-opened spirodienone linkage, in Novosphingobium aromaticivorans DSM12444. In vitro assays using cell lysates demonstrated that RS14230 (LsdE) converts DGPD to a lignostilbene intermediate, which the carotenoid oxygenase, LsdA, then converts to vanillin. A Pseudomonas putida KT2440 strain engineered with lsdEA expression catabolizes erythro-DGPD, but not threo-DGPD. We further engineered P. putida to convert DGPD to a product, cis,cis-muconic acid. Overall, this work demonstrates the potential to identify new enzymatic reactions in N. aromaticivorans and expands the biological funnel of P. putida for microbial lignin valorization.

59 BASIC BIOLOGICAL SCIENCES↗

Performance of Base and Noble Metals for Electrocatalytic Hydrogenation of Bio-Oil-Derived Oxygenated Compounds

Electrocatalytic hydrogenation is a particularly attractive approach for converting the most unstable compounds in biogenic feedstocks at ambient conditions without external hydrogen. Here, we synthesized a variety of carbon-supported transition metal catalysts and characterized their activity for the electrocatalytic hydrogenation of a series of model compounds and pyrolysis oil. Carbonyl compounds, especially aromatic aldehydes, such as furfural and benzaldehyde, are particularly inclined to hydrogenation driven by an applied current. This was verified with pure solutions of the model compounds and with pyrolysis oil, where we achieved stable and steady continuous operation on Pd. By choosing the optimal catalyst composition, the conversion of benzaldehyde shifted from alcohol production (e.g., on Pd and Cu) to dimerization (e.g., on Co, Ni, and Zn). Pd and Cu were shown to offer the best compromise between reaction rates and efficiency although, in general, base metals offer similar conversions but better efficiencies that noble metals. Thus, the present work offers foundational results and guidelines for choosing the optimal metal catalyst and the applied potential for processing organic feedstocks as a function of its composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

P–P Coupling with and without Terminal Metal–Phosphorus Intermediates

Terminal metal–phosphorus (M–P) complexes are of significant contemporary interest as potential platforms for P-atom transfer (PAT) chemistry. Decarbonylation of metal–phosphaethynolate (M–PCO) complexes has emerged as a general synthetic approach to terminal M–P complexes. M–P complexes that are stabilized by strong M–P multiple bonds are kinetically persistent and isolable. In the absence of strong M–P stabilization, the formation of diphosphorus-bridged complexes (i.e., M–P–P–M species) is often interpreted as evidence for the intermediacy of reactive, unobserved M–P species. Here, we demonstrate that while diphosphorus complexes can arise from reactive M–P species, P–P coupling can also proceed directly from M–PCO species without the intermediacy of M–P complexes. Photochemical decarbonylations of a pincer-supported Ni (II)–PCO complex at 77 K afford a spectroscopically observed terminal Ni–P complex, which is best described as a triplet, Ni(II)-metallophosphinidene with two unpaired electrons localized on the atomic phosphorus ligand. Thermal annealing of this transient Ni–P complex results in rapid dimerization to afford the corresponding P 2 2– -bridged dinickel complex. Unexpectedly, the same P 2 2– -bridged dinickel complex can also be accessed via a thermally promoted process in the absence of light. The analysis of reaction kinetics, isotope-labeling studies, and computational results indicate that the thermal P–P coupling process proceeds via a noncanonical mechanism that avoids terminal M–P intermediates. Together, these results represent the first observation of P–P coupling from characterized terminal M–P species and demonstrate that terminal M–P intermediates are not required to obtain P–P coupling products. These observations provide critical mechanistic understanding of the activation modes relevant to P-atom transfer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tungsten single-atom catalysts for the efficient conversion of isobutene into highly branched liquid hydrocarbons

The catalytic transformation of isobutene into branched liquid hydrocarbons is crucial for the production of reformulated gasoline and fuel additives. Conventional supported catalysts often lack high activity and selectivity toward the desired highly branched dimers and trimers in isobutene oligomerization. Here, by developing a tungsten single-atom catalyst (W SAC ) atomically dispersed on a silica-doped alumina (SDA) support, we report that the W SAC /SDA catalyst enables efficient and selective conversion of isobutene into highly branched C 8 and C 12 liquid olefins while suppressing the formation of heavier hydrocarbons. The atomically dispersed W 1 –O 3 moieties incorporated within the SDA support were synthesized via a high-temperature pyrolysis of a templating zinc metal–organic framework (Zn-MOF) under argon, followed by annealing in static air. The W SAC /SDA catalysts with 1.6–3.7 wt% W loading exhibited single-atom dispersion (∼0.2 nm) and outstanding performance, achieving up to 60% and 95% selectivity to branched C8 olefins at 150 °C and 250 °C, respectively, under ambient pressure. With the demonstrated high activity, selectivity, and stability, the W SAC /SDA catalyst system presents a promising platform for next-generation heterogeneous catalysts for the efficient and selective upgrading of isobutene into high-performance fuel additives.

Branched Olefins↗

Two polymorphs of [Rh(μ-I)(COD)] 2

The solid-state structure of di-μ-iodido-bis{[(1,2,5,6-η)-cycloocta-1,4-diene]rhodium(I)}, [Rh 2 I 2 (C 8 H 12 ) 2 ] or [Rh(μ-I)(COD)] 2 , was determined from two crystals with different morphologies, which were found to correspond to two polymorphs containing Rh dimers with significantly different molecular structures. Both polymorphs are monoclinic and the [Rh(μ-I)(COD)] 2 molecules in each case possess C 2 v symmetry. However, the core geometry of the butterfly-shaped Rh 2 I 2 core differs substantially. In the C 2/ c polymorph, the core geometry of [Rh(μ-I)(COD)] 2 B is bent, with a hinge angle of 96.13 (8)° and a Rh...Rh distance of 2.9612 (11) Å. The P 2 1 / c polymorph features a more planar [Rh(μ-I)(COD)] 2 P core geometry, with a hinge angle of 145.69 (9)° and a Rh...Rh distance of 3.7646 (5) Å.

36 MATERIALS SCIENCE↗

Unraveling the mechanism of recognition of the 3’ splice site of the adenovirus major late promoter intron by the alternative splicing factor PUF60

Pre-mRNA splicing is critical for achieving required amounts of a transcript at a given time and for regulating production of encoded protein. A given pre-mRNA may be spliced in many ways, or not at all, giving rise to multiple gene products. Numerous splicing factors are recruited to pre-mRNA splice sites to ensure proper splicing. One such factor, the 60 kDa poly(U)-binding splicing factor (PUF60), is recruited to sites that are not always spliced, but rather function as alternative splice sites. In this study, we characterized the interaction of PUF60 with a splice site from the adenovirus major late promoter (the AdML 3' splice site, AdML3’). We found that the PUF60–AdML3’ dissociation constants are in the micromolar range, with the binding affinity predominantly provided by PUF60’s two central RNA recognition motifs (RRMs). A 1.95 Å crystal structure of the two PUF60 RRMs in complex with AdML3’ revealed a dimeric organization placing two stretches of nucleic acid tracts in opposing directionalities, which can cause looping of nucleic acid and explain how PUF60 affects pre-mRNA geometry to effect splicing. Solution characterization of this complex by light-scattering and UV/Vis spectroscopy suggested a potential 2:1 (PUF60 2 :AdML3’) stoichiometry, consistent with the crystal structure. This work defines the sequence specificity of the alternative splicing factor PUF60 at the pre-mRNA 3’ splice site. Our observations suggest that control of pre-mRNA directionality is important in the early stage of spliceosome assembly, and advance our understanding of the molecular mechanism by which alternative and constitutive splicing factors differentiate among 3’ splice sites.

59 BASIC BIOLOGICAL SCIENCES↗

Inelastic Neutron Scattering Data for Ba₃Zn(Ru₀.₁Sb₁.₉)O₉

This dataset contains inelastic neutron scattering measurements on the magnetically dilute compound Ba₃Zn(Ru₀.₁Sb₁.₉)O₉, collected at the Spallation Neutron Source using the Cold Neutron Chopper Spectrometer (CNCS) and the SEQUOIA Fine-Resolution Fermi Chopper Spectrometer. The sample consists of nominally 5% magnetic Ru⁵⁺ ions (S = 3/2) randomly substituted into a diamagnetic Sb⁵⁺ matrix. Measurements were performed at base temperature (2–5 K) and 300 K using multiple incident energies (1.00, 3.32, 12.0, and 100 meV) to resolve magnetic excitations from isolated monomers and small Ru clusters (dimers, trimers, etc.). The dataset includes raw event-mode files, momentum- and energy-resolved spectra, and supporting metadata for instrument configuration, sample environment, and reduction parameters.

36 MATERIALS SCIENCE↗

Breaking C-C Bonds via Electrochemically Mediated Hydrogen Atom Transfer Reactions

Cleaving inert SP3-SP3 carbon-carbon (C-C) bonds selectively remains a major challenge in organic chemistry and a main bottleneck in the chemical upcycling of recalcitrant polyolefin waste. Here, we present an electrochemical strategy using redox mediators to activate and break C-C bonds at room temperature and ambient pressure. Specifically, we use N-hydroxyphthalimide (NHPI) as a redox mediator that undergoes electrochemical oxidation to form the phthalimide-N-oxyl (PINO) radical to initiate hydrogen atom transfer (HAT) reactions with benzylic C-H bonds. The resulting benzylic carbon radical is readily captured by molecular oxygen to form a peroxy radical that decomposes into oxygenated C-C bond-scission fragments. This indirect, mediated approach for Csp3-Csp3 bond cleavage reduces the oxidation potential by > 1.2 V compared to the direct oxidation of the substrate, thereby eliminating deleterious side reactions, such as solvent oxidation, that may occur at high potentials. Studies with a bibenzyl model compound revealed a bifurcated reaction pathway following the initial HAT step. At a bibenzyl conversion of 61.0%, the C-C bond cleavage pathway generates benzaldehyde and benzoic acid products at 38.4% selectivity, and the C-H bond oxygenation pathway leads to 1,2-diphenylethanone and benzil products at 39.2% selectivity. Changes in reaction selectivity were investigated with various model compounds, including bibenzyl, 1,3-diphe-nylpropane, 1,4-diphenylbutane, and their derivatives. Product selectivity is correlated with the C-C bond strength of the reactant, with weaker C-C bonds favoring the C-C bond cleavage pathway. We also evaluated the mediated oxidation of oligo-meric styrene (Mn= 510 Da, OS510) which were converted into oxygenated products. Lastly, proof-of-concept depolymeriza-tion of polystyrene (PS, ~10,000 Da) into oxygenated monomers, dimers, and oligomers was demonstrated using NHPI-mediated oxidation.

benzoic acid↗