Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “controllable loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Solid state power controllers

Solid state power controllers (SSPC's) are to be considered for use as replacements of electromechanical relays and circuit breakers in future spacecraft and aircraft. They satisfy the combined function of both the relay and circuit breaker and can be remotely controlled by small signals, typically 10 mA, 5 to 28 v(dc). They have the advantage over conventional relay/circuit breaker systems in that they can be located near the utilization equipment and the primary ac or dc bus. The low level control, trip indication and status signals can be circuited by small gauge wire for control, computer interface, logic, electrical multiplexing, onboard testing, power management, and distribution purposes. This results in increased system versatility at appreciable weight saving and increased reliability. Conventional systems require the heavy gage load wiring and the control wiring to be routed from the bus to the load to other remote relay contacts, switches, sensors, etc. and to the circuit breaker located in the flight engineer's compartment for purposes of manual reset.

Gibbs, R. S.↗
NASA NTRS1984

Road load simulator tests of the Gould phase 1 functional model silicon controlled rectifier ac motor controller for electric vehicles

The test results for a functional model ac motor controller for electric vehicles and a three-phase induction motor which were dynamically tested on the Lewis Research Center road load simulator are presented. Results show that the controller has the capability to meet the SAE-J227a D cycle test schedule and to accelerate a 1576-kg (3456-lb) simulated vehicle to a cruise speed of 88.5 km/hr (55 mph). Combined motor controller efficiency is 72 percent and the power inverter efficiency alone is 89 percent for the cruise region of the D cycle. Steady state test results for motoring, regeneration, and thermal data obtained by operating the simulator as a conventional dynamometer are in agreement with the contractor's previously reported data. The regeneration test results indicate that a reduction in energy requirements for urban driving cycles is attainable with regenerative braking. Test results and data in this report serve as a data base for further development of ac motor controllers and propulsion systems for electric vehicles. The controller uses state-of-the-art silicon controlled rectifier (SCR) power semiconductors and microprocessor-based logic and control circuitry. The controller was developed by Gould Laboratories under a Lewis contract for the Department of Energy's Electric and Hybrid Vehicle program.

Gourash, F.↗
NASA NTRS1979

Power-switch dV/dt sensing

Simple means for controlling voltage risetime and powerline noise used three transistors and capacitive feedback. Rate of change of voltage across load is reduced and controlled by circuit. Circuit is useful in situations where large wire bundles are subject to noise and crosstalk due to rapid current switching.

Jones, R. L.↗
NASA NTRS1984

Mathematical analysis

Simple continuum models used in the design, analysis, and control of large space structures are examined. Particular emphasis is placed on boundary value problems associated with the Load Correction Method and control problems involving partial differential equations for the large space structure models. Partial differential equations will be used to model a large space structure, base the design of an optimal controller on this model, approximate the resulting optimal control model, and compare the results with data from other methods.

Donaldson, J. A.↗
NASA NTRS1980

Wing/store flutter with nonlinear pylon stiffness

Recent wind tunnel tests and analytical studies show that a store mounted on a pylon with soft pitch stiffness provides substantial increase in flutter speed of fighter aircraft and reduces dependency of flutter on mass and inertia of the store. This concept, termed the decoupler pylon, utilizes a low frequency control system to maintain pitch alignment of the store during maneuvers and changing flight conditions. Under rapidly changing transient loads, however, the alignment control system may allow the store to momentarily bottom against a relatively stiff backup structure in which case the pylon stiffness acts as a hardening nonlinear spring. Such structural nonlinearities are known to affect not only the flutter speed but also the basic behavior of the instability. The influence of pylon stiffness nonlinearities or the flutter characteristics of wing mounted external stores is examined.

Desmarais, R. N.↗
NASA NTRS1980

Wing/store flutter with nonlinear pylon stiffness

Recent wind tunnel tests and analytical studies show that a store mounted on a pylon with 'soft' pitch stiffness provides substantial increase in flutter speed of fighter aircraft and reduces dependency of flutter on mass and inertia of the store. This concept, termed the decoupler pylon, utilizes a low-frequency control system to maintain pitch alignment of the store during maneuvers and changing flight conditions. Under rapidly changing transient loads, however, the alignment control system may allow the store to momentarily bottom against a relatively stiff backup structure in which case the pylon stiffness acts as a hardening nonlinear spring. Such structural nonlinearities are known to affect not only the flutter speed but also the basic behavior of the instability. This paper examines the influence of pylon stiffness nonlinearities on the flutter characteristics of wing-mounted external stores.

Desmarais, R. N.↗
NASA NTRS1983

Remote Manipulator Has Relistic "Feel"

Computer aided remote manipulator does not transmit weight and inertia of its own joints and segments. Achieves load sensitivity by processing signals that move manipulator separately from those that apply reflective forces and torques on hand controller. Operator feels only load.

Bejczy, A. K.↗
NASA NTRS1930

Determination of the Maximum Control Forces and Attainable Quickness in the Operation of Airplane Controls

This report is intended to furnish bases for load assumptions in the designing of airplane controls. The maximum control forces and quickness of operation are determined. The maximum forces for a strong pilot with normal arrangement of the controls is taken as 1.25 times the mean value obtained from tests with twelve persons. Tests with a number of persons were expected to show the maximum forces that a man of average strength can exert on the control stick in operating the elevator and ailerons and also on the rudder bar. The effect of fatigue, of duration and of the nature (static or dynamic) of the force, as also the condition of the test subject (with or without belt) were also considered.

Hertel, Heinrich↗
NASA NTRS2018

Electric Motor Noise from Small Quadcopters: Source Characteristics - Part II

The increased interest in electric motors for propulsion systems has driven interest in quantifying the contribution of electric motor noise to the overall sound levels and possible human annoyance of the propulsion system. This work presents acoustic measurements of electric motors used for small quadcopters to quantify the sound produced by a number of outrunning motors with different types of controllers. Results are presented for loaded and unloaded motors as installed and uninstalled configurations. Motor resonance frequencies were measured and computed. Current probe measurements showed that the supply current from the controllers contained significant harmonic content for the conventional and sinewave controllers. Acoustic results showed motor noise is typically radiated at frequencies near the mode 2 vibration frequency at roughly 5000 Hz. Electric motor noise was evident in the spectra produced by many of the motor-controller combinations for motors loaded with propellers with levels often greater than those for the motor alone due to increase in the stator magnetic flux density with increased current. An installed configuration produced increases in acoustic radiation over that of the uninstalled motor in a frequency range near the mode 1 vibration frequency near 1200 Hz. A companion paper (Part I - Acoustic Measurements), focuses on source identification using a phased array and directivity characteristics for a baseline configuration.

Motor Resonance Frequencies↗
NASA NTRS1984

Extension of constrained incremental Newton-Raphson scheme to generalized loading fields

This paper develops numerical strategies which enable the constrained incremental Newton-Raphson scheme to handle the static response of structure to loading fields with completely generalized histories. This is made possible through the use of specially warped hyperelliptic constraint surfaces which control successive or clustered load steps in the vicinity of loading events with specific timing schedules. Such an approach enables improved convergence and stability characteristics. Due to the generality of the methodology, pre- and postbuckling behavior caused by both kinematic and material nonlinearity can be handled. To demonstrate the scheme, the results of several bench-mark problems are also presented. These include situations involving nonlinear kinematics as well as highly history-dependent elastic-plastic and thermoelastic-plastic material behavior.

Padovan, J.↗
NASA NTRS1987

Adaptive control of dual-arm robots

Three strategies for adaptive control of cooperative dual-arm robots are described. In the position-position control strategy, the adaptive controllers ensure that the end-effector positions of both arms track desired trajectories in Cartesian space despite unknown time-varying interaction forces exerted through the load. In the position-hybrid control strategy, the adaptive controller of one arm controls end-effector motions in the free directions and applied forces in the constraint directions, while the adaptive controller of the other arm ensures that the end-effector tracks desired position trajectories. In the hybrid-hybrid control strategy, the adaptive controllers ensure that both end-effectors track reference position trajectories while simultaneously applying desired forces on the load. In all three control strategies, the cross-coupling effects between the arms are treated as disturbances which are rejected by the adaptive controllers while following desired commands in a common frame of reference. The adaptive controllers do not require the complex mathematical model of the arm dynamics or any knowledge of the arm dynamic parameters or the load parameters such as mass and stiffness. The controllers have simple structures and are computationally fast for on-line implementation with high sampling rates.

Seraji, H.↗
NASA NTRS1982

Overheat Prevention in Solar-Powered Stirling Engines

Proposed controller for solar-powered Stirling engine prevents engine from burning up when energy added by Sun exceeds that withdrawn by load. Head-temperature controller used existing electrical control unit of Stirling engine to regulate power output in response to head temperature. Power out-put is varied so keeps head temperature fairly constant.

Garrigus, W. E.↗
NASA NTRS1989

Aeroservoelastic tailoring for lateral control enhancement

The need for effective aileron power for aircraft lateral control and turning maneuvers dates back to the Wright Brothers and their wing warping concept for active stabilization of their aircraft. Early researchers in Great Britain, Japan, Germany and the United States explored ways to increase the effectiveness of control aileron to generate a roll moment. The basic problem of aileron effectiveness and the interrelationship between structural distortion and the loads applied by the control surface is illustrated. A rigid wing/aileron surface will develop the capability to generate increased roll rates as airspeed increases. A flexible surface will become less effective as airspeed increases because of the twisting distortion created by the aft-mounted control surface. This tendency is further worsened by bending distortion of an aft swept wing. This study focuses its attention on the ability of a combined effort between structural redesign of a wing and sizing and placement of a control surface to create specified roll performance with a minimum hinge moment. This design optimization problem indicates the advantages of simultaneous consideration of structural design and control design.

Weisshaar, Terrence A.↗
NASA NTRS1996

Mathematical models for electrochemical impregnation of nickel electrodes

Single step and two-step tetramer precipitation models for electrochemical impregnation of nickel electrodes are presented. The objectives for developing the impregnation model are: to predict the impregnation conditions for uniform loading, to develop quality control tools for electrode manufacturing, and to use it as basis for predicting the performance of batteries with non-uniform loadings. This paper, with the help of graphs and charts, discusses the development and application of the impregnation model.

Ho, Chien-Hsien↗
NASA NTRS1977

Development of a preprototype trace contaminant control system

The steady state contaminant load model based on shuttle equipment and material test programs, and on the current space station studies was revised. An emergency upset contaminant load model based on anticipated emergency upsets that could occur in an operational space station was defined. Control methods for the contaminants generated by the emergency upsets were established by test. Preliminary designs of both steady state and emergency contaminant control systems for the space station application are presented.

Source record↗
NASA NTRS1981

Optimal maneuvers at supersonic speeds in a vertical plane

This paper presents several optimal maneuvers of supersonic aircraft in a vertical plane. The general dimensionless equations of motion are derived and the computation of the optimal trajectories are carried out using the aerodynamics and engine characteristics of a light-weight fighter called the supercruiser. Because of the normalizing of the control variables, namely, the load factor and the thrust-to-weight ratio, the results applied to any supersonic aircraft. The optimality of the singular thrust control and the optimal junction of different subarcs are discussed. The proposed method of computing the optimal trajectory is very efficient and makes explicit the selection of the optimal control. The technique should be useful for performance assessment of supersonic aircraft with potential for implementation of onboard flight control system.

Vinh, N. X.↗
NASA NTRS1993

Six degrees of freedom vibration isolation using electromagnetic suspension

Experimental data are presented for modeling an electromagnet. Control laws are considered with and without flux feedback and with position and orientation information of the suspended body. Base motion and sensor noise are the principal disturbances. Proper selection of the geometrical operating point minimizes the passive coupling above the bandwidth of the control and filtering can attenuate the high frequency content of sensor noise. Six electromagnets are arranged in a configuration which optimizes the load support and provides control over all six degrees of freedom of the suspended body. The design is based on experimental data generated with a specially designed test facility. Application for suspension of a gravity wave antenna is discussed.

Lee, Sang-Il↗