Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conditional shift”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Division of attention as a function of the number of steps, visual shifts, and memory load

The effects on divided attention of visual shifts and long-term memory retrieval during a monitoring task are considered. A concurrent vigilance task was standardized under all experimental conditions. The results show that subjects can perform nearly perfectly on all of the time-shared tasks if long-term memory retrieval is not required for monitoring. With the requirement of memory retrieval, however, there was a large decrease in accuracy for all of the time-shared activities. It was concluded that the attentional demand of longterm memory retrieval is appreciable (even for a well-learned motor sequence), and thus memory retrieval results in a sizable reduction in the capability of subjects to divide their attention. A selected bibliography on the divided attention literature is provided.

Chechile, R. A.↗
NASA NTRS1985

The influence of sampling rate on the dynamics and control of aeronautical systems

It is shown in the design of aeronautical control systems that sampling rate variations give rise to migrations of the discrete eigenvalues for both the plant and the controllers. In general, these migrations tend to degrade simulation fidelity and the overall performance of Ultrareliable Fault Tolerant Control Systems (UFTCS). These systems consist of a redundant asynchronous network of microprocessors which use sensor information to generate the servo commands that drive actuators, thrust linkages, etc. A change in the sampling period of a single microprocessor will, in addition to causing an eigenvalue shift, alter the magnitude of the servo command issued by the controller. The influence of these changes and the effect of initial conditions and skew are considered.

Howard, J. C.↗
NASA NTRS1988

Ionospheric convection inferred from interplanetary magnetic field-dependent Birkeland currents

Computer simulations of ionospheric convection have been performed, combining empirical models of Birkeland currents with a model of ionospheric conductivity in order to investigate IMF-dependent convection characteristics. Birkeland currents representing conditions in the northern polar cap of the negative IMF By component are used. Two possibilities are considered: (1) the morning cell shifting into the polar cap as the IMF turns northward, and this cell and a distorted evening cell providing for sunward flow in the polar cap; and (2) the existence of a three-cell pattern when the IMF is strongly northward.

Rasmussen, C. E.↗
NASA NTRS1991

Shiftwork in space - Bright light as a chronobiologic countermeasure

The potential of timed exposures to bright light as a countermeasure to the changes in the work/rest schedules during space missions was investigated. In the experiments, four human subjects were exposed to two sessions of eleven days of simulated weightlessness (6-deg head-down-tilt bedrest) with 6-hr extensions of the scheduled wake time on days 3 and 4 (a 12-hr phase delay). In a blind crossover design, subjects were exposed to bright light (greater than 3500 lux) for 5 hrs on each of the two shift days and on the following day, at times expected to accelerate adaptation to the phase delay (experimental group), or have no phase shifting effect (control group). Results indicate that bright light may accelerate the rate of adaptation to work/rest schedule delays under simulated weightlessness conditions. However, such effect was found to be largely independent of the timing of the light exposure.

Gander, Philippa H.↗
NASA NTRS1995

Capillary Pressure Balance with Repeated Head-Up Tilt in Humans

We measured blood density (BD). plasma density (PD) and hematocrit (Ht) during repeated 70 deg head-up tilt (HUT) consisting of a pre-drink period with two supine (P and P3) and two HUT (P2 and P4) phases of 45 min each. At the end of P4 test subjects (N=8) drank 10 ml/kg body weight of isotonic (290 mOsm/kg) sodium chloride (ISO) or hypotonic (<10 mOsm/kg) unsweetened us (HYP), or nothing (control: CON). The following periods continued the supine (P5, P7) / upright (P6) sequence. Mass density of plasma and whole blood using a "mechanical oscillation" technique were measured from ear lobe blood. Tilting altered (p<0.001) BD, PD, and Ht in all consecutive Phases. BD and PD were different (p<0.05) between CON. HYP. and ISO Phases 6 and 7. The computed mass density of fluid (FD). which moved between intra. and extravascular compartments. averaged 1008 g/l and was the same in any conditions. In the non-drink treatment (P3, P5, P7), supine PV steadly decreased when compared to P1. Tilt-induced PV shifts ranged from 9.7 to 16.7% when compared to PV du. ring the respective previous Phases. After drinking, PV increased above CON values at the end of Phase 7 by 12.9% with ISO, and by 6.6% with HYP. Progressive hemoconcentration. occurred during non-drink supine; isotonic saline ingestion increased supine PV a control level but did not stop or reverse the decrease of upright hemoconcentration. Upright density values were not slowed with repeated upright tilting; decreased fluid loss occurred in consecutive upright periods. Upright capillary pressure balance was achieved with diminished plasma volume loss during repeated tilting.

Hinghofer-Szalkay, H. G.↗
NASA NTRS2006

Development of the Gecko (Pachydactylus turneri) Animal Model during Foton M-2 to Study Comparative Effects of Microgravity in Terrestrial and Aquatic Organisms

Terrestrial organisms exposed to microgravity during spaceflight experience degeneration in bone, muscle, and possibly other tissues that require gravity-mediated mechanical stimulation for normal regenerative growth. In the Gecko experiment aboard Foton M-2, we flew for the first time, five terrestrial Pachydactylus turneri specimens to develop a model of microgravity effects comparable to the newt Pleurodeles waltl, a well-established model organism for spaceflight. These lower vertebrate species have similar body plans and size, are poikilothermic, have tissue regenerative ability, and are adapted to moderate periods of fasting. Furthermore the gecko (Pachydactylus) can also survive prolonged periods without water. In pre-flight control experiments and after a 16-day Foton M-2 spaceflight without food or water, the geckos were recovered and showed no apparent negative health effects. However, detailed analysis of bone mass and architecture by micro Computed Tomography { pCT), showed that both synchronous control and spaceflight animals lost significant amounts of cancellous bone in the distal femur and humerus relative to basal controls. In addition, cell cycle analysis of 30h post-flight liver tissue reveals a shift of DNA content from G2 and S to G1, both in spaceflight and synchronous controls. Together, these results suggest that housing conditions alone induce rapid catabolism of cancellous bone and reduced normal tissue regeneration. Further use of the gecko Puchydactylus turneri as a spaceflight model requires modification of housing conditions, possibly by including water and food, or changing other factors such as eliminating housing stresses to obtain stable bone structure and tissue regeneration during spaceflight experiments.

Almeida, E. A.↗
NASA NTRS2012

Effect of Inductive Coil Geometry on the Operating Characteristics of a Pulsed Inductive Plasma Accelerator

Operational characteristics of two separate inductive thrusters with coils of different cone angles are explored through thrust stand measurements and time-integrated, un- filtered photography. Trends in impulse bit measurements indicate that, in the present experimental configuration, the thruster with the inductive coil possessing a smaller cone angle produced larger values of thrust, in apparent contradiction to results of a previous thruster acceleration model. Areas of greater light intensity in photographs of thruster operation are assumed to qualitatively represent locations of increased current density. Light intensity is generally greater in images of the thruster with the smaller cone angle when compared to those of the thruster with the larger half cone angle for the same operating conditions. The intensity generally decreases in both thrusters for decreasing mass ow rate and capacitor voltage. The location of brightest light intensity shifts upstream for decreasing mass ow rate of propellant and downstream for decreasing applied voltage. Recognizing that there typically exists an optimum ratio of applied electric field to gas pressure with respect to breakdown efficiency, this result may indicate that the optimum ratio was not achieved uniformly over the coil face, leading to non-uniform and incomplete current sheet formation in violation of the model assumption of immediate formation where all the injected propellant is contained in a magnetically-impermeable current sheet.

Hallock, Ashley K.↗
NASA NTRS2012

Effect of Inductive Coil Geometry on the Operating Characteristics of an Inductive Pulsed Plasma Thruster

Operational characteristics of two separate inductive thrusters with conical theta pinch coils of different cone angles are explored through thrust stand measurements and time- integrated, unfiltered photography. Trends in impulse bit measurements indicate that, in the present experimental configuration, the thruster with the inductive coil possessing a smaller cone angle produced larger values of thrust, in apparent contradiction to results of a previous thruster acceleration model. Areas of greater light intensity in photographs of thruster operation are assumed to qualitatively represent locations of increased current density. Light intensity is generally greater in images of the thruster with the smaller cone angle when compared to those of the thruster with the larger half cone angle for the same operating conditions. The intensity generally decreases in both thrusters for decreasing mass flow rate and capacitor voltage. The location of brightest light intensity shifts upstream for decreasing mass flow rate of propellant and downstream for decreasing applied voltage. Recognizing that there typically exists an optimum ratio of applied electric field to gas pressure with respect to breakdown efficiency, this result may indicate that the optimum ratio was not achieved uniformly over the coil face, leading to non-uniform and incomplete current sheet formation in violation of the model assumption of immediate formation where all the injected propellant is contained in a magnetically-impermeable current sheet.

Hallock, Ashley K.↗
NASA NTRS2019

Growth Response of Water Hyacinth to Environmental Ranges in the California Sacramento-San Joaquin River Delta

Management of aquatic weeds in complex watersheds and river systems present many challenges to assessment, planning, and implementation of management for aquatic invasive plants. The Delta Region Areawide Aquatic Weed Project (DRAAWP), a USDA sponsored area-wide project including NASA Ames Research Center and State of California Department of Boating and Waterways, is working to enhance decision-making and operational efficiency of invasive plant management in the California Sacramento-San Joaquin Delta. Expansion of invasive aquatic plants has been detrimental to water management and the ecosystem complex in the San Francisco Bay/California Delta. The portion of DRAAWP reported here focuses on parametrizing the environmental response inputs for the Delta models for prominent invasive aquatic plants. Changing climate, long-term drought, shifts in land use, and variation in water flow and quality from input watersheds lead to wide and unique variation in environmental conditions. Environmental variability occurs across a range of time scales from long-term climate and seasonal trends to short-term water flow mediated variations. Response of invasive aquatic plants are examined using controlled environment growth facilities at time scales of weeks, day, and hours using a combination of study duration and growth assessment techniques to assess water quality, temperature, nutrient, and light effects. These provide response parameters for plant growth models in response to the variation and interact with management and economic models associated with aquatic weed management. Plant growth models are informed by remote sensing and applied spatially across the Delta to balance location and type of aquatic plant, growth response to altered environments and phenology.

Sacramento-San Joaquin River Delta.v↗
NASA NTRSDate not supplied

Bluntness and Supersaturation Effects on the Second Mode Instability in Mach 10 Flow

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 31-Inch Mach 10 Tunnel to investigate the impact of nosetip radius and freestream supersaturation on the development of the second mode instability. The model was instrumented with surface-mounted Kulite® and PCB® pressure transducers and thermocouples. Power spectral density plots demonstrate the anticipated trends of the second mode instability weakening and shifting to lower frequencies with increased bluntness. Heat transfer measurements suggest laminar flow over the bulk of the model for most testing conditions, with evidence of transition by the cone base for the sharpest nosetip (R = 0.15 mm) at the higher unit Reynolds numbers. The dynamic surface pressure and heat transfer measurements show that reducing the temperature of the freestream to a supersaturated state has a significant stabilizing effect on the model boundary layer. The surface measurements are observed to be highly dependent on the level of clustering in the freestream. Significant changes in surface pressure spectra due to total temperature reduction are first noted below T0= 948 K, while more substantial fluctuation reductions are found below T0= 810 K.

Hypersonics↗
NASA NTRS2020

Computational Simulations of a Mach 0.745 Transonic Truss-Braced Wing Design

A joint effort between the NASA Ames and Langley Research Centers was undertaken to analyze the Mach 0.745 variant of the Boeing Transonic Truss-Braced Wing (TTBW) Design. Two different flow solvers, LAVA and USM3D, were used to predict the TTBW flight performance. Sensitivity studies related to mesh resolution and numerical schemes were conducted to define best practices for this type of geometry and flow regime. Validation efforts compared the numerical simulation results of various modeling methods against experimental data taken from the NASA Ames 11-foot Unitary Wind Tunnel experimental data. The fidelity of the computational representation of the wind tunnel experiment, such as utilizing a porous wall boundary condition to model the ventilated test section, was varied to examine how different tunnel effects influence CFD predictions. LAVA and USM3D results both show an approximate 0.5 angle of attack shift from experimental lift curve data. This drove an investigation that revealed that the trailing edge of the experimental model was rounded in comparison to the CAD model, due to manufacturing tolerances, which had not been accounted for in the initial simulations of the experiment. Simulating the TTBW with an approximation of this rounded trailing-edge reduces error by approximately 60%. An accurate representation of the tested TTBW geometry, ideally including any wing twists and deflections experienced during the test under various loading conditions, will be necessary for proper validation of the CFD.

Maldonado, Daniel↗
DOE OSTI2024

Lithium Plating Characteristics in High Areal Capacity Li-Ion Battery Electrodes

Li-ion battery degradation and safety events are often attributed to undesirable metallic lithium plating. Since their release, Li-ion battery electrodes have been made progressively thicker to provide a higher energy density. However, the propensity for plating in these thicker pairings is not well understood. Herein, we combine an experimental plating-prone condition with robust mesoscale modeling to examine electrode pairings with capacities ranging from 2.5 to 6 mAh/cm 2 and negative to positive (N/P) electrode areal capacity ratio from 0.9 to 1.8 without the need for extensive aging tests. Using both experimentation and a mesoscale model, we identify a shift from conventional high state-of-charge (SOC) type plating to high overpotential (OP) type plating as electrode thickness increases. Further, these two plating modes have distinct morphologies, identified by optical microscopy and electrochemical signatures. We demonstrate that under operating conditions where these plating modes converge, a high propensity of plating exists, revealing the importance of predicting and avoiding this overlap for a given electrode pairing. Further, we identify that thicker electrodes, beyond a capacity of 3 mAh/cm 2 or thickness >75 μm, are prone to high OP, limiting negative electrode (NE) utilization and preventing cross-sectional oversizing the NE from mitigating plating. Here, it simply contributes to added mass and volume. The experimental thermal gradient and mesoscale model either combined or independently provide techniques capable of probing performance and safety implications of mild changes to electrode design features.

25 ENERGY STORAGE↗
DOE OSTI2022

MPC solution for optimal load shifting for buildings with ON/OFF staged packaged units: Experimental demonstration, and lessons learned

Small and medium-sized commercial buildings (SMCB) are significant demand response resources, and it is important to develop grid-responsive control algorithms that exploit those resources and create financial benefits for building owners and HVAC service providers. Furthermore, unlike large-sized commercial buildings, there is an opportunity to have universally applicable control solutions for many SMCBs since those buildings have a consistent HVAC system configuration: SMCBs are commonly served by multiple-staged air conditioning units controlled by their own thermostats. Despite the demand response potential and scalability, however, very few control solutions are available for SMCBs. Typical model predictive control (MPC) and heuristic control approaches for cooling load shifting that lower thermostat setpoints before an electric price jump are suitable mainly for large-sized commercial buildings where a continuous capacity modulation is possible, e.g., via dampers in variable air volume terminal units. However, those approaches can cause undesired, high peaks for SMCBs due to the nature of ON/OFF unit staging and narrow thermostat deadbands. This could discourage the use of advanced grid-responsive controls for SMCBs due to the concern of high demand charges, and has to be resolved. This paper presents a MPC solution that overcomes this challenge. It has a hierarchical MPC structure where an upper level MPC is responsible for electrical load shifting in response to an electric price signal while a lower level MPC is responsible for coordinating compressor stages to eliminate unnecessary peaks and follows the setpoints determined by the upper level MPC. In this work, two one-month, comprehensive laboratory tests have been carried out to demonstrate load shifting and cost savings for the algorithm. Interesting trade-offs between energy efficiency and load flexibility were observed and are discussed, and lessons learned for applying MPCs for SMCBs are also presented.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS2017

An Experimental Flow-Through Assessment of Acidic Fe/Mg Smectite Formation on Early Mars

Orbital observations have detected the phyllosilicate smectite in layered material hundreds of meters thick, intracrater depositional fans, and plains sediments on Mars; however, the detection of carbonate deposits is limited. Instead of neutral/alkaline conditions during the Noachian, early Mars may have experienced mildly acidic conditions derived from volcanic acid-sulfate solutions that allowed Fe/Mg smectite formation but prevented widespread carbonate formation. The detection of acid sulfates (e.g., jarosite) associated with smectite in Mawrth Vallis supports this hypothesis. Previous work demonstrated smectite (saponite) formation in closed hydrologic systems (batch reactor) from basaltic glass at pH 4 and 200°C (Peretyazhko et al., 2016 GCA). This work presents results from alteration of basaltic glass from alkaline to acidic conditions in open hydrologic systems (flow-through reactor). Preliminary experiments exposed basaltic glass to deionized water at 190°C at 0.25 ml/min where solution pH equilibrated to 9.5. These initial high pH experiments were conducted to evaluate the flow-through reactor system before working with lower pHs. Smectite at this pH was not produced and instead X-ray diffraction results consistent with serpentine was detected. Experiments are in progress exposing basaltic glass from pH 8 down to pH 3 to determine what range of pHs could allow for smectite formation in this experimental opensystem. The production of smectite under an experimental open-system at low pHs if successful, would support a significant paradigm shift regarding the geochemical evolution of early Mars: Early Mars geochemical solutions were mildly acidic, not neutral/alkaline. This could have profound implications regarding early martain microbiology where acid conditions instead of neutral/alkaline conditions will require further research in terrestrial analogs to address the potential for biosignature preservation on Mars.

Sutter, Brad↗
DOE OSTI2023

Wildland Fires in the Subtropical Hill Forests of Southeastern Bangladesh

The first ever comprehensive study on wildland fires in Bangladesh is carried out to develop a fire prevention and prediction method. The major causes of huge wildland fires (88%) in the subtropical Chittagong Hill forest (43% of total) of southern Bangladesh are reported as shifting cultivation, grazing and unauthorized settlement. We used satellite hotspot (HS) data from 2003 to 2021 (a total of 54,669 HSs) to clarify the spatio-temporal structure of wildland fires. Fire weather conditions were analyzed using various weather data and synoptic-scale weather maps at different air levels. Fires concentrated from March through April or a transitional period from the dry season, caused by the Asian winter monsoon, to the wet season, due to the Asian summer monsoon. Fire occurrence depended on dry conditions and pre-monsoon showers and their timing. The difference in 925 hPa heights of high and low pressure systems may be attributed to the different types of the Asian winter and summer monsoons. The average maximum air temperature and incident shortwave solar energy in April were the highest and strongest, contributing fire-prone weather conditions. Based on the analysis, a fire prevention and prediction method will be developed, and this report may also facilitate the establishment of future CO 2 reduction measures for Bangladesh.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2020

Computational Simulations of a Mach 0.745 Transonic Truss-Braced Wing Design

A joint effort between the NASA Ames and Langley Research Centers was undertaken to analyze the Mach 0.745 variant of the Boeing Transonic Truss-Braced Wing (TTBW) Design. Two different flow solvers, LAVA and USM3D, were used to predict the TTBW flight performance. Sensitivity studies related to mesh resolution and numerical schemes were conducted to define best practices for this type of geometry and flow regime. Validation efforts compared the numerical simulation results of various modeling methods against experimental data taken from the NASA Ames 11-foot Unitary Wind Tunnel experimental data. The fidelity of the computational representation of the wind tunnel experiment, such as utilizing a porous wall boundary condition to model the ventilated test section, was varied to examine how different tunnel effects influence CFD predictions. LAVA and USM3D results both show an approximate 0.5o angle of attack shift from experimental lift curve data. This drove an investigation that revealed that the trailing edge of the experimental model was rounded in comparison to the CAD model, due to manufacturing tolerances, which had not been accounted for in the initial simulations of the experiment. Simulating the TTBW with an approximation of this rounded trailing-edge reduces error by approximately 60%. An accurate representation of the tested TTBW geometry, ideally including any wing twists and deflections experienced during the test under various loading conditions, will be necessary for more thorough validation of the CFD.

Maldonado, Daniel↗
DOE OSTI2025

Detecting Reactive Products in Carbon Capture Polymers with Chemical Shift Anisotropy and Machine Learning

Aminopolymers are attractive sorbents for CO 2 direct air capture applications due to their high density of amine groups, which can readily react with atmospheric levels of CO 2 to form chemisorbed species. The identity of these chemisorbed species and the functional groups that form upon oxidative degradation depends on both material properties and processing conditions, forming a variety of carbonyl-type sites such as ammonium carbamates, bicarbonates, carbonates, carbamic acids, ureas, and amides. 13 C solid-state nuclear magnetic resonance (NMR) is often used to help elucidate the identity of these reacted species, but it is challenging due to the narrow chemical shift range of carbonyl sites. Herein, we demonstrate the application of a two-dimensional (2D) chemical shift anisotropy (CSA) recoupling pulse sequence (ROCSA) to obtain CSA tensor values at each isotropic chemical shift, overcoming limitations of isotropic peak resolution. CSA tensor values describe the local chemical environment and can readily differentiate between the chemisorbed and degradation products. To aid identification, we also developed a k-nearest neighbor (kNN) classification model to distinguish the functional groups via their CSA tensor parameters. This methodology was demonstrated on poly(ethylenimine) in γ-Al 2 O 3 exposed to CO 2 and showed that the chemisorbed products are ammonium carbamate and a mixed carbamate–carbamic acid species. The sample was analyzed again after desorption at 100 °C inducing mild degradation, and the remaining products were strongly bound carbamate and urea species. In conclusion, the combination of 2D CSA measurements coupled with a kNN classification model enhances the ability to accurately identify chemisorbed or degradation products in complex carbon capture materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Consequences of adsorbate-adsorbate interactions for apparent kinetics of surface catalytic reactions

Lateral adsorbate interactions at catalyst surfaces are known to influence adsorption energies and reaction rates. Lattice-based kinetic Monte Carlo (kMC) simulations are able to capture these influences, but such models are typically parameterized for a specific reaction network and catalyst surface. Here we report kMC simulations to probe the influence of lateral interactions on simulated rates, rate orders, apparent activation energies, and Sabatier plots. We construct a simple, two-step reaction network involving a single adsorbate and rate- limiting diatomic dissociation, employ a generic repulsive lateral interaction model consistent with known adsorbate-adsorbate interactions on metal surfaces, and a rate model consistent with known Brønsted-Evans-Polyani relationships for diatomic dissocations. Furthermore, we juxtapose reaction kinetics over a wide range of reaction conditions and catalyst binding energies, as a function of interaction strength. We find that at a given zero-coverage binding energy and external conditions, adsorbate coverage decreases monotonically with increasing interaction strength, but absolute rates can vary linearly or nonlinearly. Interactions flatten the Sabatier volcano and shift the maximum towards stronger binding. Influences on apparent rate orders and activation energies are modest and are sensitive to interaction-induced adsorbate ordering. Model predictions are sensitive to lattice size effects at high coverages. The results, modelled for a simple reaction system, highlight the generic consequences of lateral interactions and guidance for identifying their signatures in observed kinetics.

kinetic Monte Carlo↗