Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “computer experiment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

A study of Mariner 10 flight experiences and some flight piece part failure rate computations

The problems and failures encountered in Mariner flight are discussed and the data available through a quantitative accounting of all electronic piece parts on the spacecraft are summarized. It also shows computed failure rates for electronic piece parts. It is intended that these computed data be used in the continued updating of the failure rate base used for trade-off studies and predictions for future JPL space missions.

Paul, F. A.↗
NASA NTRS1981

In situ data analysis on high altitude balloons using microprocessors

It is pointed out that systems currently in use permit an uplink data rate from scientific balloons to satellites of only 100 bit/min. On-board microprocessors, which are able to condense data, can address this problem. An experiment is described that demonstrates the capabilities of inflight data processing by an on-board computer for electric field experiments. It was possible to reduce the data rate by two orders of magnitude with no diminution of data quality.

Schroeder, K. R.↗
NASA NTRS1981

Experience on the use of MOSTAB-HFW computer code for horizontal-axis wind turbines

Three topics are covered dealing with the frequencies of a rotating beam, the use of the fundamental mode of a uniform cantilever beam, and the analysis of resonance dwell. Immensely high peak loads were generated by the code for resonance dwell indicating further need for including structural damping and for transient analysis capability. The effect of structural damping, newly incorporated in the code, is described.

Yu, Y. Y.↗
NASA NTRS1987

Experiences with the Lanczos method on a parallel computer

A parallel computer implementation of the Lanczos method for the free-vibration analysis of structures is considered, and results for two example problems show substantial time-reduction over the sequential solutions. The major Lanczos calculation tasks are subdivided into subtasks, and parallelism is introduced at the subtask level. A speedup of 7.8 on eight processors was obtained for the decomposition step of the problem involving a 60-m three-longeron space mast, and a speedup of 14.6 on 16 processors was obtained for the decomposition step of the problem involving a blade-stiffened graphite-epoxy panel.

Bostic, Susan W.↗
NASA NTRS1993

Computational study of a conical wing having unit aspect ratio at supersonic speeds

A study was conducted to identify and assess a computational method as a preliminary analysis and design tool for advanced military aircraft designs. The method of choice for this study was the Euler Marching Technique for Accurate Computation (EMTAC). Computational and experimental results were compared for a thick unit aspect ratio delta wing at Mach 2.8 and 4.0. This geometry along with the associated flow physics is representative of advanced aircraft designs. The comparisons of the lift and drag coefficients show that the computations agree with experimentally obtained data at Mach 2.8 and 4.0. Further, comparison between EMTAC and experiment shows that the computations accurately predict the overall shape and levels of the surface pressure distributions at Mach 2.8 and 4.0. Qualitative assessment of the computed flow-field properties shows that EMTAC captures the basic flow-field characteristics representative of advanced aircraft designs. The study further suggests that EMTAC can be successfully used in the preliminary analysis and design of advanced military aircraft.

Mcgrath, Brian E.↗
NASA NTRS2011

Analytical Solution and Physics of a Propellant Damping Device

NASA design teams have been investigating options for "detuning" Ares I to prevent oscillations originating in the vehicle solid-rocket main stage from synching up with the natural resonance of the rest of the vehicle. An experimental work started at NASA MSFC center in 2008 using a damping device showed great promise in damping the vibration level of an 8 resonant tank. However, the mechanisms of the vibration damping were not well understood and there were many unknowns such as the physics, scalability, technology readiness level (TRL), and applicability for the Ares I vehicle. The objectives of this study are to understand the physics of intriguing slosh damping observed in the experiments, to further validate a Computational Fluid Dynamics (CFD) software in propellant sloshing against experiments with water, and to study the applicability and efficiency of the slosh damper to a full scale propellant tank and to cryogenic fluids. First a 2D fluid-structure interaction model is built to model the system resonance of liquid sloshing and structure vibration. A damper is then added into the above model to simulate experimentally observed system damping phenomena. Qualitative agreement is found. An analytical solution is then derived from the Newtonian dynamics for the thrust oscillation damper frequency, and a slave mass concept is introduced in deriving the damper and tank interaction dynamics. The paper will elucidate the fundamental physics behind the LOX damper success from the derivation of the above analytical equation of the lumped Newtonian dynamics. Discussion of simulation results using high fidelity multi-phase, multi-physics, fully coupled CFD structure interaction model will show why the LOX damper is unique and superior compared to other proposed mitigation techniques.

Yang, H. Q.↗
NASA NTRS1976

Estimating normal mixture parameters from the distribution of a reduced feature vector

A FORTRAN computer program was written and tested. The measurements consisted of 1000 randomly chosen vectors representing 1, 2, 3, 7, and 10 subclasses in equal portions. In the first experiment, the vectors are computed from the input means and covariances. In the second experiment, the vectors are 16 channel measurements. The starting covariances were constructed as if there were no correlation between separate passes. The biases obtained from each run are listed.

Guseman, L. F.↗
NASA NTRS1982

Scout trajectory error propagation computer program

Since 1969, flight experience has been used as the basis for predicting Scout orbital accuracy. The data used for calculating the accuracy consists of errors in the trajectory parameters (altitude, velocity, etc.) at stage burnout as observed on Scout flights. Approximately 50 sets of errors are used in Monte Carlo analysis to generate error statistics in the trajectory parameters. A covariance matrix is formed which may be propagated in time. The mechanization of this process resulted in computer program Scout Trajectory Error Propagation (STEP) and is described herein. Computer program STEP may be used in conjunction with the Statistical Orbital Analysis Routine to generate accuracy in the orbit parameters (apogee, perigee, inclination, etc.) based upon flight experience.

Myler, T. R.↗
NASA NTRS1982

Computer program to minimize prediction error in models from experiments with 16 hypercube points and 0 to 6 center points

A previous report described a backward deletion procedure of model selection that was optimized for minimum prediction error and which used a multiparameter combination of the F - distribution and an order statistics distribution of Cochran's. A computer program is described that applies the previously optimized procedure to real data. The use of the program is illustrated by examples.

Holms, A. G.↗
NASA NTRS2013

Computational Study of the CC3 Impeller and Vaneless Diffuser Experiment

Centrifugal compressors are compatible with the low exit corrected flows found in the high pressure compressor of turboshaft engines and may play an increasing role in turbofan engines as engine overall pressure ratios increase. Centrifugal compressor stages are difficult to model accurately with RANS CFD solvers. A computational study of the CC3 centrifugal impeller in its vaneless diffuser configuration was undertaken as part of an effort to understand potential causes of RANS CFD mis-prediction in these types of geometries. Three steady, periodic cases of the impeller and diffuser were modeled using the TURBO Parallel Version 4 code: 1) a k-epsilon turbulence model computation on a 6.8 million point grid using wall functions, 2) a k-epsilon turbulence model computation on a 14 million point grid integrating to the wall, and 3) a k-omega turbulence model computation on the 14 million point grid integrating to the wall. It was found that all three cases compared favorably to data from inlet to impeller trailing edge, but the k-epsilon and k-omega computations had disparate results beyond the trailing edge and into the vaneless diffuser. A large region of reversed flow was observed in the k-epsilon computations which extended from 70% to 100% span at the exit rating plane, whereas the k-omega computation had reversed flow from 95% to 100% span. Compared to experimental data at near-peak-efficiency, the reversed flow region in the k-epsilon case resulted in an under-prediction in adiabatic efficiency of 8.3 points, whereas the k-omega case was 1.2 points lower in efficiency.

Kulkarni, Sameer↗
NASA NTRS2013

Computational Study of the CC3 Impeller and Vaneless Diffuser Experiment

Centrifugal compressors are compatible with the low exit corrected flows found in the high pressure compressor of turboshaft engines and may play an increasing role in turbofan engines as engine overall pressure ratios increase. Centrifugal compressor stages are difficult to model accurately with RANS CFD solvers. A computational study of the CC3 centrifugal impeller in its vaneless diffuser configuration was undertaken as part of an effort to understand potential causes of RANS CFD mis-prediction in these types of geometries. Three steady, periodic cases of the impeller and diffuser were modeled using the TURBO Parallel Version 4 code: (1) a k-ε turbulence model computation on a 6.8 million point grid using wall functions, (2) a k-ε turbulence model computation on a 14 million point grid integrating to the wall, and (3) a k-ω turbulence model computation on the 14 million point grid integrating to the wall. It was found that all three cases compared favorably to data from inlet to impeller trailing edge, but the k-ε and k-ω computations had disparate results beyond the trailing edge and into the vaneless diffuser. A large region of reversed flow was observed in the k-ε computations which extended from 70 to 100 percent span at the exit rating plane, whereas the k-ω computation had reversed flow from 95 to 100 percent span. Compared to experimental data at near-peak-efficiency, the reversed flow region in the k-ε case resulted in an underprediction in adiabatic efficiency of 8.3 points, whereas the k-ω case was 1.2 points lower in efficiency.

Kulkarni, Sameer↗
NASA NTRS1991

Mixing of multiple jets with a confined subsonic crossflow - Summary of NASA-supported experiments and modeling

Experimental and computational results on the mixing of single, double, and opposed rows of jets with an isothermal or variable temperature mainstream in a confined subsonic crossflow are summarized. The studies were performed to investigate flow and geometric variations typical of the complex 3D flowfield in the dilution zone of combustion chambers in gas turbine engines. The principal observations from the experiments were that the momentum-flux ratio was the most significant flow variable, and that temperature distributions were similar (independent of orifice diameter) when the orifice spacing and the square-root of the momentum-flux ratio were inversely proportional. The experiments and empirical model for the mixing of a single row of jets from round holes were extended to include several variations typical of gas turbine combustors.

Holdeman, James D.↗
NASA NTRS1975

Computers vs. wind tunnels for aerodynamic flow simulations

It is pointed out that in other fields of computational physics, such as ballistics, celestial mechanics, and neutronics, computations have already displaced experiments as the principal means of obtaining dynamic simulations. In the case of aerodynamic investigations, the complexity of the computational work involved in solving the Navier-Stokes equations is the reason that such investigations rely currently mainly on wind-tunnel testing. However, because of inherent limitations of the wind-tunnel approach and economic considerations, it appears that at some time in the future aerodynamic studies will chiefly rely on computational flow data provided by the computer. Taking into account projected development trends, it is estimated that computers with the required capabilities for a solution of the complete viscous, time-dependent Navier-Stokes equations will be available in the mid-1980s.

Chapman, D. R.↗
NASA NTRS1991

Mixing of multiple jets with a confined subsonic crossflow. Summary of NASA-supported experiments and modeling

Experimental and computational results on the mixing of single, double, and opposed rows of jets with an isothermal or variable temperature mainstream in a confined subsonic crossflow are summarized. The studies were performed to investigate flow and geometric variations typical of the complex 3-D flowfield in the dilution zone of combustion chambers in gas turbine engines. The principal observations from the experiments were that the momentum-flux ratio was the most significant flow variable, and that temperature distributions were similar (independent of orifice diameter) when the orifice spacing and the square-root of the momentum-flux ratio were inversely proportional. The experiments and empirical model for the mixing of a single row of jets from round holes were extended to include several variations typical of gas turbine combustors. Combinations of flow and geometry that gave optimum mixing were identified from the experimental results. Based on results of calculations made with a 3-D numerical model, the empirical model was further extended to model the effects of curvature and convergence. The principle conclusions from this study were that the orifice spacing and momentum-flux relationships were the same as observed previously in a straight duct, but the jet structure was significantly different for jets injected from the inner wall wall of a turn than for those injected from the outer wall. Also, curvature in the axial direction caused a drift of the jet trajectories toward the inner wall, but the mixing in a turning and converging channel did not seem to be inhibited by the convergence, independent of whether the convergence was radial or circumferential. The calculated jet penetration and mixing in an annulus were similar to those in a rectangular duct when the orifice spacing was specified at the radius dividing the annulus into equal areas.

Holdeman, James D.↗
NASA NTRS1979

Simulations of the monthly mean atmosphere for February 1976 with the GISS model

Three monthly mean simulations of the global atmosphere were computed for February 1976 with the GISS model from observed initial conditions on the first day of the month. In a replication experiment, two of these computations generated slightly different monthly mean states, apparently due to the schedule of interruptions on the computer. The root-mean-square errors of replication over the Northern Hemisphere were found to be about 2 mb, 20 m and 1 K for sea level pressure, 500 mb height and 850 mb temperature, respectively. The monthly mean 500 mb forecast results for February 1976 over the Northern Hemisphere are consistent with those from earlier GISS model experiments and again indicate some predictive skill at that level. Use of the observed monthly mean sea surface temperature (SST) field for February 1976 in place of the climatological SST field for February resulted in slightly improved simulations over the globe and Northern Hemisphere,

Spar, J.↗
NASA NTRS1983

Simulation of turbulent shear flows at Stanford and NASA-Ames - What can we do and what have we learned?

The capabilities and limitations of large eddy simulation (LES) and full turbulence simulation (FTS) are outlined. It is pointed out that LES, although limited at the present time by the need for periodic boundary conditions, produces large-scale flow behavior in general agreement with experiments. What is more, FTS computations produce small-scale behavior that is consistent with available experiments. The importance of the development work being done on the National Aerodynamic Simulator is emphasized. Studies at present are limited to situations in which periodic boundary conditions can be applied on boundaries of the computational domain where the flow is turbulent.

Reynolds, W. C.↗