Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “circuit optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

An optimized three-dimensional linear-electric-field time-of-flight analyzer

In situ measurements of the dynamics and composition of space plasmas have greatly improved our understanding of the space environment. In particular, mass spectrometers that use a combination of electrostatic analyzers and time-of-flight systems can identify revealing dynamic and compositional characteristics of ions, and thus constrain their sources and the physical processes relevant for their transport. We demonstrate an optimized design of a linear-electric-field time-of-flight technology that can be used to obtain a high signal to noise: ions that follow an energy-isochronous oscillation within the instrument impact an emissive plate and cause secondary electrons to be sent toward the detector, triggering a high-resolution measurement. By focusing these secondary electrons to a central area on a position-sensitive anode, their signals are separated from ions and neutrals that do not experience energy-isochronous motion. Using their impact positions, the high mass resolution measurements are easily distinguished from other signals on the detector, leading to very favorable signal-to-noise ratios. This optimization provides an improvement to existing technologies without increasing the instrument size or complexity, and uses a novel time-of-flight circuit that combines timing and position information from many signals and ions.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Change in Inertial Confinement Fusion Implosions upon Using an Ab Initio Multiphase DT Equation of State

Improving the description of the equation of state (EOS) of deuterium-tritium (DT) has recently been shown to change significantly the gain of an inertial confinement fusion target [S. X. Hu et al., Phys. Rev. Lett. 104, 235003 (2010)]. Here we use an advanced multiphase EOS, based on ab initio calculations, to perform a full optimization of the laser pulse shape with hydrodynamic simulations starting from 19 K in DT ice. The thermonuclear gain is shown to be a robust estimate over possible uncertainties of the EOS. Two different target designs are discussed, for shock ignition and self-ignition. In the first case, the areal density and thermonuclear energy can be recovered by slightly increasing the laser energy. In the second case, a lower in-flight adiabat is needed, leading to a significant delay (3 ns) in the shock timing of the implosion.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

CRCNS22 Learning Rules in the Hippocampus and their Mapping to Neuromorphic Systems (Final Technical Report)

Large scale biologically-realistic computational models are key to investigating the interplay between structure and function in nervous systems, thus paving the way to new clinical methods and neuro-inspired computing solutions. This project focuses on the hippocampus, in particular the CA3-CA1 regions, due to their role in associative learning and memory, pattern separation and completion, and spatial navigation. Investigations into the neuronal organization and learning rule(s) of this circuit can shed light into how declarative memories are formed, stored, recalled and forgotten and inform computational, experimental and clinical neuroscience work. Our project aims at developing a novel data-driven methodology supported by a broad heterogeneous base of neuroscience experimental knowledge and inspired from advances in computer science and engineering. Specifically, this work will benchmark existing and new learning rules within a full-scale spiking neural network simulation of the CA3-CA1 region. The model will be based on an open-source repository, called the Hippocampome, which contains neuronal morphologies, firing patterns, synapse probabilities, and most other required parameters for all known neuron types in the rodent hippocampal formation. The model will be first trained in a supervised fashion for associative memory tasks using backpropagation through time traditionally used in computer science, enhanced with a new technique called the surrogate gradient method. This optimization method will be used to obtain a global loss minimization, but it is not biologically inspired as it assumes the use of data not locally available to the synapses. However, we propose its use as a benchmarking tool, to compare the training performance of local biologically plausible and hardware-mappable learning rules at scale. New rules or combinations will be proposed and tested as needed, based on the obtained results. Progress in this area will also drive the development of novel hardware-mappable algorithms for continual lifelong learning and categorization of new events from few presented examples. This project goes beyond the existing state-of-the-art by looking at large scale realistic neuronal circuits as networks trainable via global optimization methods such as surrogate gradient descent. The objective function of the brain that supports learning is largely unknown, but it is likely that it operates through local learning rules. Studying network trajectories around local minima as proposed in this work represents a useful strategy for understanding whether a network is training by using a specific (set of) learning rule(s). Starting from a completely untrained network is a challenging test since it is difficult to determine how the learning rule affects the trajectory of the network. This interdisciplinary project will help understand what rule governs learning in these regions or if multiple learning rules are involved. The work will develop a robust methodology to measure if the network is converging to the target solution, oscillating around it, or diverging away.

59 BASIC BIOLOGICAL SCIENCES↗

Design optimization of an additively manufactured prototype recuperator for supercritical CO 2 power cycles

Supercritical CO 2 (sCO 2 ) power cycles are being developed due to their potential for high efficiency and reduced capital cost. It is necessary that these recuperators operate at high pressures and temperatures, up to 30 MPa and 900 K, with effectiveness values > 95% and pressure drops <1% to achieve high cycle efficiencies. Moreover, it is also necessary to have reasonable cost recuperators to control the capital costs of the sCO 2 power cycles. In this study, a Plate Pin-Fin (PPF) heat exchanger has been proposed as an sCO 2 recuperator. This preliminary recuperator design leverages capabilities enabled by additive manufacturing. Although the PPF design has characteristics similar to those of a plate heat exchanger, small diameter and relatively long fins are used to increase surface area, enhance heat transfer, and provide structural support for the partition plates that separate the fluid streams. Existing correlations for heat transfer and pressure drop were adapted for the PPF heat exchanger. These correlations were implemented in a 1D analytical model and used for the optimization of a 5-kW th high temperature recuperator for an indirect sCO 2 cycle by varying the design parameters to minimize the quantity of material required. A 3D conjugate heat transfer numerical simulations were conducted to validate the heat transfer and pressure loss correlations. A steepest descent method was used to minimize heat exchanger mass for a 5-kW prototype recuperator subject to a maximum specified pressure drop. Additionally, the design analysis indicated that an optimum PPF recuperator would be attained for the minimum allowable pin transverse spacing, minimum pin width, minimum pin height and near maximum cell aspect ratio. Moreover, at a low material requirement of 0.216 kg/kW and a pressure drop, which is almost five times lower than the allowable pressure drop design target, the optimized PPF heat exchanger has the high potential to be an alternative to a printed circuit heat exchanger, which is a conservative design basis for the current state-of-the-art sCO 2 recuperators.

42 ENGINEERING↗

Plasma Radiation Source on the Basis of the Gas Puff with Outer Plasma Shell in the Circuit of a Mega-Ampere Load Current Doubler

Characteristics of Z-pinch plasma radiation in the form of a double shell neon gas puff with outer plasma shell are investigated in the microsecond implosion mode. Experiments are performed using a GIT-12 mega-joule generator with load current doubler having a ferromagnetic core at implosion currents up to 5 MA. Conditions for matching of the nonlinear load with the mega-ampere current multiplier circuit are determined. The load parameters (plasma shell characteristics and mass and geometry of gas puff shells) are optimized on the energy supplied to the gas puff and n energy characteristics of radiation. It is established that the best modes of K-shell radiation in neon are realized for such radial distribution of the gas-puff material at which the compression velocity of the shell is close to a constant and amounts to 27–30 cm/μs. In these modes, up to 40% of energy supplied to the gas puff is converted into K-shell radiation. The reasons limiting the efficiency of the radiation source with increasing implosion current are analyzed. A modernized version of the energy supply from the current doubler to the Z-pinch is proposed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Patterned anodes with sub-millimeter spatial resolution for large-area MCP-based photodetector systems

Micro-channel-plate-based photo-detectors are unique in being capable of covering very large areas such as those required in elementary particle and nuclear physics, while providing sub-millimeter space resolution, time resolutions of less than 10 picoseconds for charged particles, and time resolutions of 30 psec–50 psec for single photons. In such systems the electronic channel count is a major cost driver. Incorporating a capacitively-coupled anode allows the use of external pickup electrodes with patterns of individual channels optimized for occupancy, rate, and time/space resolution. The signal pickup antenna can be economically implemented as a printed circuit card with a 2-dimensional array of pads for high-occupancy/high-rate applications such as in particle colliders and medical imaging, or a 1-dimensional array of strips for a lower channel count in low-occupancy/low-rate applications such as large neutrino detectors. In this paper we present pad patterns that enhance signal-sharing between pads to lower the channel count per unit area in large-area systems by factors up to 4, while maintaining spatial resolutions of approximately 100 to 200 μ m for charged particles and 400 to 1000 μ m for single photons. Patterns that use multiple signal layers in the signal-pickup board can lower the channel count even further, moving the scaling behavior in the number of pads versus total area from quadratic to linear.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Laser annealing of electrodeposited CuInSe 2 semiconductor precursors: experiment and modeling

Laser annealing can reduce the annealing time required to form Cu(In,Ga)(S,Se) 2 (CIGSe) thin films for use in thin film photovoltaics to a single second timescale, if not faster. In this work, we use microstructural characterization coupled with modeling of the optical and thermal properties to understand the laser annealing of three types of electrodeposited precursor stacks for the CIGSe parent compound CuInSe 2 . The precursor films are: stacked elemental layers Cu/In/Se, stacked binary selenides In 2 Se 3 /Cu 2– x Se, and a single layer of coelectrodeposited Cu–In–Se. Conceptually, these stacks are ordered in terms of decreasing stored chemical and interfacial potential free energy, consideration of which predicts that the formation of large grained CuInSe 2 from the stacked elemental layers would be the most exothermic and thus most rapid process. However we find that microstructural details of the electrodeposited films such as void fraction present in the stacked binary selenides dramatically alter the heat and mass flow. Additionally, modeling of the optical absorption within the elemental stacked precursor suggests extremely localized heating at the In/Se interface resulting in significant Se loss. Despite its lower chemical potential energy, the coelectrodeposited CuInSe 2 precursor's more uniform optical absorption of near-bandgap light coupled with its compact, low void fraction microstructure of nano-sized grains results in the most optimal recrystallization and compositional homogenization via interdiffusion. Furthermore this annealed layer formed a working device with a short circuit current density of 23 mA cm –2 . As a result, this combined modeling and experimental investigation underscores the need to consider practical micro- and nanostructure-dependent properties as well as the optical absorption and not simply thermodynamics when designing accelerated two step deposition and annealing processes for compound semiconductors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Efficient solution-processed small molecule: Cadmium selenide quantum dot bulk heterojunction solar cells

We report bulk heterojunction solar cells based on blends of solution-processed small molecule [7,7′-(4,4-bis(2-ethylhexyl)-4H-silolo[3,2-b:4,5-b′]dithiophene-2,6-diyl) bis(6-fluoro-4-(5′-hexyl-[2,2′-bithiophen]-5yl)benzo[c] [1,2,5] thiadiazole)] p-DTS(FBTTh{sub 2}){sub 2}: Cadmium Selenide (CdSe) (70:30, 60:40, 50:50, and 40:60) in the device configuration: Indium Tin Oxide /poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)/p-DTS(FBTTh{sub 2}){sub 2}: CdSe/Ca/Al. The optimized ratio of p-DTS(FBTTh{sub 2}){sub 2}:CdSe::60:40 leads to a short circuit current density (J{sub sc}) = 5.45 mA/cm{sup 2}, open circuit voltage (V{sub oc}) = 0.727 V, and fill factor (FF) = 51%, and a power conversion efficiency = 2.02% at 100 mW/cm{sup 2} under AM1.5G illumination. The J{sub sc} and FF are sensitive to the ratio of p-DTS(FBTTh{sub 2}){sub 2}:CdSe, which is a crucial factor for the device performance.

36 MATERIALS SCIENCE↗

High-efficiency AlGaInP solar cells grown by molecular beam epitaxy

AlGaInP is an ideal material for ultra-high efficiency, lattice-matched multi-junction solar cells grown by molecular beam epitaxy (MBE) because it can be grown lattice-matched to GaAs with a wide 1.9–2.2 eV bandgap. Despite this potential, AlGaInP grown by molecular beam epitaxy (MBE) has yet to be fully explored, with the initial 2.0 eV devices suffering from poor performance due to low minority carrier diffusion lengths in both the emitter and base regions of the solar cell. In this work, we show that implementing an AlGaInP graded layer to introduce a drift field near the front surface of the device enabled greatly improved internal quantum efficiency (IQE) across all wavelengths. In addition, optimizing growth conditions and post-growth annealing improved the long-wavelength IQE and the open-circuit voltage of the cells, corresponding to a 3× increase in diffusion length in the base. Taken together, this work demonstrates greatly improved IQE, attaining peak values of 95%, combined with an uncoated AM1.5G efficiency of 10.9%, double that of previously reported MBE-grown devices.

Faucher, J.↗

Defect filtering for thermal expansion induced dislocations in III–V lasers on silicon

Epitaxially integrated III–V semiconductor lasers for silicon photonics have the potential to dramatically transform information networks, but currently, dislocations limit performance and reliability even in defect-tolerant InAs quantum dot (QD)-based lasers. Despite being below the critical thickness, QD layers in these devices contain previously unexplained misfit dislocations, which facilitate non-radiative recombination. We demonstrate here that these misfit dislocations form during post-growth cooldown due to the combined effects of (1) thermal-expansion mismatch between the III–V layers and silicon and (2) mechanical hardening in the active region. By incorporating an additional sub-critical thickness, indium-alloyed “misfit dislocation trapping layer,” we leverage these mechanical hardening effects to our advantage, displacing 95% of misfit dislocations from the QD layer in model structures. Unlike conventional dislocation mitigation strategies, the trapping layer reduces neither the number of threading dislocations nor the number of misfit dislocations. It simply shifts the position of misfit dislocations away from the QD layer, reducing the defects' impact on luminescence. In full lasers, adding a misfit dislocation trapping layer both above and below the QD active region displaces misfit dislocations and substantially improves performance: we measure a twofold reduction in lasing threshold currents and a greater than threefold increase in output power. Overall, our results suggest that devices employing both traditional threading dislocation reduction techniques and optimized misfit dislocation trapping layers may finally lead to fully integrated, commercially viable silicon-based photonic integrated circuits.

36 MATERIALS SCIENCE↗

Exploring thermal equilibria of the Fermi-Hubbard model with variational quantum algorithms

Here, this study investigates the thermal properties of the repulsive Fermi-Hubbard model with chemical potential using variational quantum algorithms, crucial in comprehending particle behaviour within lattices at heightened temperatures in condensed matter systems. Conventional computational methods encounter challenges, especially in managing chemical potential, prompting exploration into Hamiltonian approaches. Despite the promise of quantum algorithms, their efficacy is hampered by coherence limitations when simulating extended imaginary time evolution sequences. To overcome these constraints, this research focuses on optimizing variational quantum algorithms to probe the thermal properties of the Fermi-Hubbard model. Physics-inspired circuit designs are tailored to alleviate coherence constraints, facilitating a more comprehensive exploration of materials at elevated temperatures. Our study demonstrates the potential of variational algorithms in simulating the thermal properties of the Fermi-Hubbard model while acknowledging limitations stemming from error sources in quantum devices and encountering barren plateaus.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Physics-Based Analysis of Cell Imbalances and Aging in Lithium-Ion Battery Modules and Packs

Lithium-ion battery (LIB) packs are a key solution for grid-scale energy storage, enabling grid resilience and supporting critical infrastructure. LIB modules and packs experience current imbalances and uneven cell aging due to various design and operational factors, and require a battery management system (BMS) to continuously monitor and control. In this context, a physics-based modeling framework for LIB modules and packs (liionpack) was enhanced to identify design and control strategies that minimize current imbalance and improve module/pack operation. Simulations of an 8-cell parallel-connected module demonstrate that reducing current imbalance leads to more uniform cell aging and improved module/pack-level degradation predictions. The analysis shows that current imbalance are affected by the electrical resistances. Terminal location significantly affects imbalance, with opposite-end terminal connections at intermediate branches minimizing the imbalance, and the pack circuit construction influences the accuracy of physics-based analysis at the pack scale. This framework enables design optimization of modules and packs through a fast and easy evaluation of pack performance and aging, and supports the development of aging-informed balancing strategies compatible with BMS implementation. Thereby, offering practical pathways to improve reliability and cycle life predictions in large-scale battery energy storage systems.

Ayalasomayajula, Surya Mitra [Oak Ridge National L↗

Compact Heat Exchanger Design and Testing for Advanced Reactors and Advanced Power Cycles

The goal of the proposed research is to demonstrate the thermal hydraulic performance of innovative surface geometries in compact heat exchangers used as intermediate heat exchangers (IHXs) and recuperators for the supercritical carbon dioxide (s-CO 2 ) Brayton cycle. Printed-circuit heat exchangers (PCHEs) are the primary compact heat exchangers of interest. The overall objectives are: To develop optimized PCHE designs for different working fluid combinations including helium to s-CO 2 , liquid salt to s-CO 2 , sodium to s-CO 2 , and liquid salt to helium; To experimentally and numerically investigate thermal performance, thermal stress and failure mechanism of PCHEs under various transients; and To study diffusion bonding techniques for elevated-temperature alloys and examine post-test material integrity of the PCHEs. The project objectives were accomplished by defining and executing five different tasks corresponding to these specific objectives. The first task involved a thorough literature review and a selection of IHX candidates with different surface geometries as well as a summary of prototypic operational conditions. The second task involved optimization of PCHE design with numerical analyses of thermal-hydraulic performances and mechanical integrity. The subsequent task dealt with the development of testing facilities and engineering design of PCHE to be tested in s-CO 2 fluid conditions. The next task involved experimental investigation and validation of the thermal-hydraulic performances and thermal stress distribution of prototype PCHEs manufactured with particular surface geometries. The last task involved an investigation of diffusion bonding process and posttest destructive testing to validate mechanical design methods adopted in the design process. The experimental work utilized the two test facilities at The Ohio State University (OSU) including one existing High-Temperature Helium Test Facility (HTHF) and the newly developed s-CO 2 test loop (STL) facility and s-CO 2 test facility at University of Wisconsin – Madison (UW).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Multiphase complete exchange: A theoretical analysis

Complete Exchange requires each of N processors to send a unique message to each of the remaining N-1 processors. For a circuit switched hypercube with N = 2(sub d) processors, the Direct and Standard algorithms for Complete Exchange are optimal for very large and very small message sizes, respectively. For intermediate sizes, a hybrid Multiphase algorithm is better. This carries out Direct exchanges on a set of subcubes whose dimensions are a partition of the integer d. The best such algorithm for a given message size m could hitherto only be found by enumerating all partitions of d. The Multiphase algorithm is analyzed assuming a high performance communication network. It is proved that only algorithms corresponding to equipartitions of d (partitions in which the maximum and minimum elements differ by at most 1) can possibly be optimal. The run times of these algorithms plotted against m form a hull of optimality. It is proved that, although there is an exponential number of partitions, (1) the number of faces on this hull is Theta(square root of d), (2) the hull can be found in theta(square root of d) time, and (3) once it has been found, the optimal algorithm for any given m can be found in Theta(log d) time. These results provide a very fast technique for minimizing communication overhead in many important applications, such as matrix transpose, Fast Fourier transform, and ADI.

Bokhari, Shahid H.↗

Initial results for the silicon monolithically interconnected solar cell product

This proprietary technology is based on AstroPower's electrostatic bonding and innovative silicon solar cell processing techniques. Electrostatic bonding allows silicon wafers to be permanently attached to a thermally matched glass superstrate and then thinned to final thicknesses less than 25 micron. These devices are based on the features of a thin, light-trapping silicon solar cell: high voltage, high current, light weight (high specific power) and high radiation resistance. Monolithic interconnection allows the fabrication costs on a per watt basis to be roughly independent of the array size, power or voltage, therefore, the cost effectiveness to manufacture solar cell arrays with output powers ranging from milliwatts up to four watts and output voltages ranging from 5 to 500 volts will be similar. This compares favorably to conventionally manufactured, commercial solar cell arrays, where handling of small parts is very labor intensive and costly. In this way, a wide variety of product specifications can be met using the same fabrication techniques. Prototype solar cells have demonstrated efficiencies greater than 11%. An open-circuit voltage of 5.4 volts, fill factor of 65%, and short-circuit current density of 28 mA/sq cm at AM1.5 illumination are typical. Future efforts are being directed to optimization of the solar cell operating characteristics as well as production processing. The monolithic approach has a number of inherent advantages, including reduced cost per interconnect and increased reliability of array connections. These features make this proprietary technology an excellent candidate for a large number of consumer products.

Dinetta, L. C.↗

Special Component Designs for Differential-Amplifier MMICs

Special designs of two types of electronic components transistors and transmission lines have been conceived to optimize the performances of these components as parts of waveguide-embedded differential-amplifier monolithic microwave integrated circuits (MMICs) of the type described in the immediately preceding article. These designs address the following two issues, the combination of which is unique to these particular MMICs: Each MMIC includes a differential double-strip transmission line that typically has an impedance between 60 and 100 W. However, for purposes of matching of impedances, transmission lines having lower impedances are also needed. The transistors in each MMIC are, more specifically, one or more pair(s) of InP-based high-electron-mobility transistors (HEMTs). Heretofore, it has been common practice to fabricate each such pair as a single device configured in the side-to-side electrode sequence source/gate/drain/gate/source. This configuration enables low-inductance source grounding from the sides of the device. However, this configuration is not suitable for differential operation, in which it is necessary to drive the gates differentially and to feed the output from the drain electrodes differentially. The special transmission-line design provides for three conductors, instead of two, in places where lower impedance is needed. The third conductor is a metal strip placed underneath the differential double-strip transmission line. The third conductor increases the capacitance per unit length of the transmission line by such an amount as to reduce the impedance to between 5 and 15 W. In the special HEMT-pair design, the side-to-side electrode sequence is changed to drain/gate/source/gate/ drain. In addition, the size of the source is reduced significantly, relative to corresponding sizes in prior designs. This reduction is justified by the fact that, by virtue of the differential configuration, the device has an internal virtual ground, and therefore there is no need for a low-resistance contact between the source and the radio-frequency circuitry. The source contact is needed only for DC biasing. These designs were implemented in a single-stage-amplifier MMIC. In a test at a frequency of 305 GHz, the amplifier embedded in a waveguide exhibited a gain of 0 dB; after correcting for the loss in the waveguide, the amplifier was found to afford a gain of 0.9 dB. In a test at 220 GHz, the overall gain of the amplifier- and-waveguide assembly was found to be 3.5 dB.

Kangaslahti, Pekka↗