Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “catalyst design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Enhanced CO 2 Methanation Activity of Sm 0.25 Ce 0.75 O 2-δ –Ni by Modulating the Chelating Agents-to-Metal Cation Ratio and Tuning Metal–Support Interactions

Highly active and selective CO 2 methanation catalysts are critical to CO 2 upgrading, synthetic natural gas production, and CO 2 emission reduction. Wet impregnation is widely used to synthesize oxide-supported metallic nanoparticles as the catalyst for CO 2 methanation. However, as the reagents cannot be homogeneously mixed at an atomic level, it is challenging to modulate the microstructure, crystal structure, chemical composition, and electronic structure of catalysts via wet impregnation. In this work, a scalable and straightforward catalyst fabrication approach has been designed and validated to produce Sm 0.25 Ce 0.75 O 2-δ -supported Ni (SDC–Ni) as the CO 2 methanation catalyst. By varying the chelating agents-to-total metal cations ratio (C/I ratio) during the catalyst synthesis, we can readily and simultaneously modulate the microstructure, metallic surface area, crystal structure, chemical composition, and electronic structure of SDC–Ni, consequently fine-tuning the oxide–support interactions and CO 2 methanation activity. The optimal C/I ratio (0.1) leads to an SDC–Ni catalyst that facilitates C–O bond cleavage and significantly improves CO 2 conversion at 250 °C. A CO 2 -to-CH 4 yield of >73% has been achieved at 250 °C. Furthermore, a stable operation of >1500 hours has been demonstrated, and no degradation is observed. Extensive characterizations were performed to fundamentally understand how to tune and enhance CO 2 methanation activity of SDC–Ni by modulating the C/I ratio. The correlation of physical, chemical, and catalytic properties of SDC–Ni with the C/I ratio is established and thoroughly elaborated in this work. This study could be applied to tune the oxide–support interactions of various catalysts for enhancing the catalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A molten carbonate shell modified perovskite redox catalyst for anaerobic oxidative dehydrogenation of ethane

Acceptor-doped, redox-active perovskite oxides such as La 0.8 Sr 0.2 FeO 3 (LSF) are active for ethane oxidation to CO x but show poor selectivity to ethylene. This article reports molten Li 2 CO 3 as an effective “promoter” to modify LSF for chemical looping–oxidative dehydrogenation (CL-ODH) of ethane. Under the working state, the redox catalyst is composed of a molten Li 2 CO 3 layer covering the solid LSF substrate. The molten layer facilitates the transport of active peroxide (O 2 2- ) species formed on LSF while blocking the nonselective sites. Spectroscopy measurements and density functional theory calculations indicate that Fe 4+ →Fe 3+ transition is responsible for the peroxide formation, which results in both exothermic ODH and air reoxidation steps. With >90% ethylene selectivity, up to 59% ethylene yield, and favorable heat of reactions, the core-shell redox catalyst has an excellent potential to be effective for intensified ethane conversion. The mechanistic findings also provide a generalized approach for designing CL-ODH redox catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Directing reaction pathways via in situ control of active site geometries in PdAu single-atom alloy catalysts

Abstract The atomic scale structure of the active sites in heterogeneous catalysts is central to their reactivity and selectivity. Therefore, understanding active site stability and evolution under different reaction conditions is key to the design of efficient and robust catalysts. Herein we describe theoretical calculations which predict that carbon monoxide can be used to stabilize different active site geometries in bimetallic alloys and then demonstrate experimentally that the same PdAu bimetallic catalyst can be transitioned between a single-atom alloy and a Pd cluster phase. Each state of the catalyst exhibits distinct selectivity for the dehydrogenation of ethanol reaction with the single-atom alloy phase exhibiting high selectivity to acetaldehyde and hydrogen versus a range of products from Pd clusters. First-principles based Monte Carlo calculations explain the origin of this active site ensemble size tuning effect, and this work serves as a demonstration of what should be a general phenomenon that enables in situ control over catalyst selectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Designing Heteroatom-Codoped Iron Metal–Organic Framework for Promotional Photoreduction of Carbon Dioxide to Ethylene

Rational engineering active sites and vantage defects of catalysts are promising but grand challenging task to enhance photoreduction CO 2 to high value-added C2 products. In this study, we designed an N,S-codoped Fe-based MIL-88B catalyst with well-defined bipyramidal hexagonal prism morphology via a facile and effective process, which was synthesized by addition of appropriate 1,2-benzisothiazolin-3-one (BIT) and acetic acid to the reaction solution. Under simulated solar irradiation, the designed catalyst exhibits high C 2 H 4 evolution yield of 17.7 μmol g -1 ∙h, which has been rarely achieved in photocatalytic CO 2 reduction process. The synergistic effect of Fe-N coordinated sites and reasonable defects in the N,S-codoped photocatalyst can accelerate the migration of photogenerated carriers, resulting in high electron density, and this in turn helps to facilitate the formation and dimerization of C-C coupling intermediates for C 2 H 4 effectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Unraveling the core of fuel cell performance: engineering the ionomer/catalyst interface

The biggest obstacle to the widespread implementation of polymer electrolyte membrane fuel cells (PEMFCs) is their cost, primarily due to the use of platinum catalysts. The high intrinsic catalyst activity exhibited on a rotating disk electrode (RDE) is rarely realized in a membrane electrode assembly (MEA), which is a long-standing challenge for PEMFCs and a cause of low catalyst utilization. To translate the high RDE performance of a catalyst into a MEA, the design of an ideal ionomer/catalyst interface is proposed: a thin, conformal ionomer film covers the maximum surface of a Pt nanoparticle and thus simultaneously maximizes catalyst utilization, (i.e., high mass activity and electrochemically active surface area) and O 2 diffusion rate (i.e., high current density performance) without compromising proton conduction. Building such an interface is a long-standing challenge due to the lack of interaction between the ionomer and catalyst particles, resulting in large ionomer agglomerates and inhomogeneous ionomer coverage over the catalyst nanoparticle, with consequent poor fuel cell performance. In this work, this ionomer/catalyst interface has been engineered, utilizing the electrostatic attraction between positively charged catalyst and negatively charged ionomer particles in a catalyst ink and preserved in a solid catalyst layer. As a result, this interface leads to previously unachieved proton exchange membrane fuel cell performance in terms of both catalyst utilization (75% vs. 45%) and peak/rated power density (i.e., 1.430/0.930 W cm -2 , H 2 /air, cathode Pt loading: 0.1 mgPt cm -2 ) for pure Pt catalysts, even better than those of Pt alloy catalysts. This work demonstrates the formation of an interface in the liquid phase (using ultra-small-angle X-ray scattering in combination with cryo-TEM, isothermal–titration–calorimetry) and the preservation of the interface in the solid catalyst layer (using TEM) and estimates the effective coverage and thickness of the ionomer film (using limiting current density, RDE and fuel cell performance).

25 ENERGY STORAGE↗
DOE OSTI2022

CO 2 Hydrogenation to Methanol over Inverse ZrO 2 /Cu(111) Catalysts: The Fate of Methoxy under Dry and Wet Conditions

Understanding the surface chemistry of CH 3 O species is essential for the production of methanol by CO 2 hydrogenation over Cu-based heterogeneous catalysts, as it facilitates the rational design of more efficient conversion processes. Recent research has identified inverse ZrO 2 /Cu catalysts as highly active and selective systems for the transformation of CO 2 to methanol with a performance that can be better than that of commercial Cu/ZnO catalysts. Here, we employed synchrotron-based ambient pressure X-ray photoelectron spectroscopy (AP-XPS) and calculations based on density functional theory (DFT) to understand the fate of CH 3 O groups under dry and wet environments. AP-XPS spectra revealed that under CO 2 hydrogenation conditions, formate and methoxy are two key intermediates to produce methanol. Furthermore, there are three different types of reactive sites on the surface: One is active for methoxy adsorption, which is stable and responsible for the methanol synthesis; Another one transforms CO 2 into CO; and a third one is active for CO 2 and methoxy dissociation, leading to C and methane formation. The theoretical calculations indicate that CH 3 OH readily dissociates to CH 3 O species following a highly exothermic (ΔE = -20.99 kcal/mol) and barrierless process. The water produced by the reverse water-gas shift reaction (CO 2 + H 2 → H 2 O + CO) can prevent the decomposition of CH 3 O species. We discovered that by introducing a tiny amount of water vapor (2 × 10 -6 Torr) into the reaction chamber, the energy barrier for the reaction CH 3 O(ads) + H(ads) → CH 3 OH(gas) is dramatically reduced. AP-XPS and computational modelling showed that water is quite capable of extracting adsorbed methoxy to form gaseous methanol. With this in mind, one could boost the methanol selectivity by adding appropriate amounts of water or steam, which is an inexpensive and feasible solution for industrial operations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Ce x Zr 1– x O 2 -Supported CrO x Catalysts for CO 2 -Assisted Oxidative Dehydrogenation of Propane–Probing the Active Sites and Strategies for Enhanced Stability

CO 2 -assisted oxidative dehydrogenation of propane (CO 2 -ODH) represents an attractive approach for propylene production and CO 2 utilization. As a soft oxidant, CO 2 can minimize overoxidation of the hydrocarbons to enhance the propylene selectivity while increasing the equilibrium yield. However, a major challenge of CO 2 -ODH is the rapid deactivation of the catalysts. The current study focuses on designing Ce x Zr 1–x O 2 -mixed oxide-supported CrO x catalysts for CO 2 -ODH with enhanced product selectivity and catalyst stability. By doping 0–30% Ce in the Ce x Zr 1–x O 2 mixed oxide support, propane conversion of 53–79% was achieved at 600 °C, with propylene selectivity up to 82%. Compared to the pure ZrO 2 -supported catalyst (i.e., 5 wt %Cr/ZrO 2 ), 20–30 %Ce doped catalysts (i.e., 5 wt %Cr/Ce 0.2 Zr 0.8 O 2 and 5 wt %Cr/Ce 0.3 Zr 0.7 O 2 ) inhibited the formation of CH 4 and ethylene and improved propylene selectivity from 57 to 77–82%. Detailed characterizations of the 5%Cr/Ce 0.2 Zr 0.8 O 2 catalyst and density functional theory (DFT) calculations indicated that Cr 3+ is the active species during the CO 2 -ODH reaction, and the reaction follows a non-redox dehydrogenation pathway. Coke formation was determined to be the primary reason for catalyst deactivation, and the addition of Ce to the ZrO 2 support greatly enhanced the coke resistance, leading to superior stability. Furthermore, coke removal by oxidizing the catalyst in air is effective in restoring its activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Constructing Highly Durable Fuel Cell Catalysts Through Integrating Graphitic Shell‐Protected Composite Carbon Support with Gaseous Co Deposition‐Driven PtCo Intermetallics

Metal dissolution, nanoparticle agglomeration, and carbon support corrosion cause significant performance degradation of current PtCo catalysts under acidic and oxidative oxygen reduction reaction. Here, in this study, an integrated strategy is presented to design high-performance Pt 3 Co intermetallic catalysts by regulating gaseous Co deposition-driven diffusion into Pt nanoparticles supported on a composite carbon. The composite carbon is derived from ZIF-8/polyaniline, consisting of a high-surface-area (HSC) core and a protective graphitic shell (GS), which is employed to design 40 wt.% Pt/HSC@GS catalyst. The corresponding membrane electrode assemblies (MEAs) can maintain 1.09 A cm −2 at 0.7 V (20. 7% loss) after 10 000 cycles (1.0–1.5 V for carbon stability) and 1.15 A cm −2 (16.1% loss) after 150 000 cycles (0.60–0.95 V for catalyst stability). A ordered Pt 3 Co intermetallic is synthesized via a gaseous Co-deposition process, which yields a homogeneous Co-rich layer onto the Pt nanoparticles on the composite support, thereby facilitating Co diffusion into Pt crystal during subsequent ordering annealing to form the ordered intermetallic structure. This gaseous deposition leads to a thin carbon layer on PtCo nanoparticles, inhibiting particle growth during the annealing and mitigating Co dissolution under dynamic electrochemical conditions. The PtCo catalyst achieves impressive MEA performance and long-term durability (1.45 A cm −2 at 0.7 V after 120 000 cycles) under heavy-duty conditions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2026

Regulating in situ gaseous deposition to construct highly durable Fe–N–C oxygen-reduction fuel cell catalysts

The activity–stability trade-off challenges the design of high-performance atomically dispersed iron–nitrogen–carbon (Fe–N–C) catalysts for the acidic oxygen reduction reaction in polymer electrolyte fuel cells. Here we develop an in situ chemical vapour deposition approach during catalyst synthesis to break the trade-off, producing highly stable Fe–N–C catalysts while maintaining adequate oxygen reduction reaction activity. The optimal catalyst exhibits a half-wave potential of 0.867 V, remaining unchanged after an accelerated stress test (AST) of 100,000 potential cycles in rotating disk electrode tests. In membrane electrode assemblies under H 2 –air conditions, it delivers 93 mA cm −2 at 0.8 V after a standard AST of 30,000 voltage cycles, and shows minimal current density losses (2.9% at 0.6 V; 14.2% at 0.7 V) after an extended AST up to 120,000 cycles. Furthermore, the catalyst’s durability improvement is primarily due to the in situ chemical vapour deposition, which strengthens Fe–N bonds, increases active-site density, mitigates iron aggregates and reduces surface porosity.

Chemical engineering↗
DOE OSTI2021

Direct Integration of Strained-Pt Catalysts into Proton-Exchange-Membrane Fuel Cells with Atomic Layer Deposition

The design and fabrication of lattice-strained platinum catalysts achieved by removing a soluble core from a platinum shell synthesized via atomic layer deposition, is reported. The remarkable catalytic performance for the oxygen reduction reaction (ORR), measured in both half-cell and full-cell configurations, is attributed to the observed lattice strain. By further optimizing the nanoparticle geometry and ionomer/carbon interactions, mass activity close to 0.8 A mg Pt -1 @0.9 V iR-free is achievable in the membrane electrode assembly. Nevertheless, active catalysts with high ORR activity do not necessarily lead to high performance in the high-current-density (HCD) region. More attention shall be directed toward HCD performance for enabling high-power-density hydrogen fuel cells.

25 ENERGY STORAGE↗
DOE OSTI2025

Surface engineering of Pt nanocatalysts with transition metal oleates for selective catalysis: a case study on the hydrogenation of α,β-unsaturated aldehydes

Selective and active catalysts enable effective use of feedstocks, reduced energy consumption and waste generation. Tuning the electronic structure of heterogeneous metal nanocatalysts via their surface modifications is a promising strategy to design highly selective and active catalysts for the synthesis of harder to make and more cost-efficient products. Here, we introduce transition metal oleates as a new class of ligands to engineer the catalytically active and very selective surface in organic solvents. Using citral hydrogenation and 5 nm Pt NPs as a model reaction and model catalytic system, respectively, we show that surface engineering of Pt nanocatalysts with metal oleates allows synthesis of desired partially hydrogenated product (geraniol) with ∼90% conversion with selectivity over 93%. We demonstrate that the selective synthesis of the unsaturated alcohols catalyzed by Pt NPs modified by adsorption of the transition metal salts cannot be explained by the widely accepted mechanism of preferred coordination of C$=$O groups by Lewis acids (e.g. partially oxidized transition surface metals). Our results indicate that C$=$O groups prefer to bind to negatively charged surfaces. We propose the explanation on how the adsorption of transition metal oleates can result in the increased electron density at the surface of Pt nanoparticles. Our study not only provides reliable solutions to selective hydrogenation but opens a new possibility of using metal oleates for the electronic ligand effect.

Kwon, Soon Gu [Argonne National Laboratory (ANL), ↗
DOE OSTI2021

Application of Molecular Catalysts for the Oxygen Reduction Reaction in Alkaline Fuel Cells

Here, the development of precious group metal-free (PGM-free) catalysts for the oxygen reduction reaction is considered as the main thrust for the cost reduction of fuel cell technologies and their mass production. Within the PGM-free category, molecular catalysts offer an advantage over other heat-treated PGM-free catalysts owing to their well-defined structure, which enables further design of more active, selective, and durable catalysts. Even though non-heat-treated molecular catalysts with exceptional performance have been reported in the past, they were rarely tested in a fuel cell. Herein, we report on a molecular catalyst under alkaline conditions: fluorinated iron phthalocyanine (FeFPc) supported on cheap and commercially available high-surface area carbon-BP2000 (FeFPc@BP2000). It exhibits the highest activity ever reported for molecular catalysts under alkaline conditions in half-cells and fuel cells.

25 ENERGY STORAGE↗
DOE OSTI2021

Conversion of cellulose to high-yield glucose in water over sulfonated mesoporous carbon fibers with optimized acidity

The hydrolysis of cellulose to high-yield glucose in water remains challenging owing to the limited acidity and substrate contact of sulfonated carbons. In this study, we report a unique sulfonated mesoporous carbon fiber with optimized acidity prepared by the pyrolysis of FeCl 3 -impregnated wipe fibers followed by acid treatment. The Bronsted acidity (especially for SO 3 H) was produced by sulfonation of the magnetic carbon fiber intermediate, while Lewis acidity originated from small Fe 3 O 4 nanoparticles and the remaining defects. The balanced Bronsted and Lewis acidity combined with hydrophilic functionalities was simultaneously tailored by varying the Fe/wipe fiber (WF) feed ratio and pyrolysis temperature to change the porous structure of the final catalysts. The elaborately fabricated MCF-SO 3 H-20-500 (20% Fe/WF feed ratio and pyrolysis at 500 degrees C) delivered 66.0% glucose yield as cellulose was completely converted. This is the highest glucose yield achieved by the hydrolysis of untreated cellulose in water over a sulfonated carbon catalyst. The optimized Bronsted and Lewis acidity was mainly responsible for the controlled conversion of cellulose to glucose, while the rich hydrophilic functionalities and superior mesoporous structure of the catalyst facilitated contact to cellulose and mass transfer. This investigation will open new avenues to design high-performance carbon sulfoacid catalysts toward cellulose hydrolysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Cooperative Brønsted-Lewis acid sites created by phosphotungstic acid encapsulated metal–organic frameworks for selective glucose conversion to 5-hydroxymethylfurfural

Production of 5-hydroxymethylfurfural (HMF) from biomass-derived glucose has great potential for synthesis of renewable fuels and chemicals. Selective glucose conversion to 5-hydroxymethylfurfural requires a balance between Lewis and Brønsted acids for the cascade of glucose isomerization followed by fructose dehydration. A dual Brønsted-Lewis acid, phosphotungstic acid encapsulated MIL-101(Al)–NH 2 metal–organic frameworks (MOFs) was developed to catalyze the glucose dehydration reaction. The encapsulated catalysts had a high HMF selectivity of 58% at 44% glucose conversion at 120°C in [C 4 C 1 im]Cl. Phosphotungstic acid was uniformly dispersed in the MOF pores, which provided both Brønsted and Lewis acid sites for this cascade reaction. The Brønsted acidic phosphotungstic acid-encapsulated MOF catalyst was stable and recyclable at least four times. Here, these findings explain the effect of phosphotungstic acid location for maximizing the HMF selectivity and suggest a new approach for the design of bifunctional solid acid catalysts for selective HMF production from glucose. Moreover, the tunability of the acid properties of the encapsulated MOF catalysts provides opportunities for other biomass transformations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Multiphysics and Multiscale Simulation Methods for Electromagnetic Energy Assisted Fossil Fuel to Hydrogen Conversion (Final Scientific/Technical Report)

This report summarizes the technical accomplishments of the four-year research project “Multiphysics and Multiscale Simulation Methods for Electromagnetic Energy Assisted Fossil Fuel to Hydrogen Conversion” (Award No. DE-FE0032092), conducted at Howard University and the University of Houston (subawardee) from September 2021 to August 2025. The project successfully achieved all four major objectives: 1. 3D Structural Characterization – Developed 3D optical imaging and mechanical sectioning methods to characterize catalyst distribution and support morphology in nickel foam substrates. Successfully reconstructed 3D geometries and imported them into COMSOL Multiphysics for electromagnetic simulations. 2. EM Hotspot Simulation – Created all-frequency stable electromagnetic formulations and 3D nodal discontinuous Galerkin (NDG) methods for coupled electromagnetic-thermal-fluid problems in multiscale catalytic media. Demonstrated stable solutions from DC to microwave frequencies. 3. Multiphysics Coupling – Developed multiscale simulation methods coupling FEM electromagnetic solvers with thermal transport equations. Reactive molecular dynamics (ReaxFF MD) simulations were performed to investigate catalytic reaction mechanisms at the atomistic level. Demonstrated electromagnetic-thermal co-simulation capabilities for porous catalyst structures. 4. System Optimization – Designed and optimized EM-assisted catalytic systems using nickel foam and carbon foam structures, demonstrating significant temperature increases due to microwave heating. Observed and characterized plasma generation in carbon fiber catalysts. Investigated multiple reaction chamber geometries for improved microwave energy deposition. The project produced significant scientific contributions including 15+ peer-reviewed publications, trained multiple Ph.D. students and undergraduate researchers, and advanced the understanding of microwave-assisted hydrogen production from fossil fuels.

08 HYDROGEN↗
DOE OSTI2021

Origin of enhanced water oxidation activity in an iridium single atom anchored on NiFe oxyhydroxide catalyst

The efficiency of the synthesis of renewable fuels and feedstocks from electrical sources is limited, at present, by the sluggish water oxidation reaction. Single-atom catalysts (SACs) with a controllable coordination environment and exceptional atom utilization efficiency open new paradigms toward designing high-performance water oxidation catalysts. Here, using operando X-ray absorption spectroscopy measurements with calculations of spectra and electrochemical activity, we demonstrate that the origin of water oxidation activity of IrNiFe SACs is the presence of highly oxidized Ir single atom (Ir 5.3+ ) in the NiFe oxyhydroxide under operating conditions. We show that the optimal water oxidation catalyst could be achieved by systematically increasing the oxidation state and modulating the coordination environment of the Ir active sites anchored atop the NiFe oxyhydroxide layers. Based on the proposed mechanism, we have successfully anchored Ir single-atom sites on NiFe oxyhydroxides (Ir 0.1 /Ni 9 Fe SAC) via a unique in situ cryogenic–photochemical reduction method that delivers an overpotential of 183 mV at 10 mA · cm – 2 and retains its performance following 100 h of operation in 1 M KOH electrolyte, outperforming the reported catalysts and the commercial IrO 2 catalysts. These findings open the avenue toward an atomic-level understanding of the oxygen evolution of catalytic centers under in operando conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1994

Inventing and improving ribozyme function: rational design versus iterative selection methods

Two major strategies for generating novel biological catalysts exist. One relies on our knowledge of biopolymer structure and function to aid in the 'rational design' of new enzymes. The other, often called 'irrational design', aims to generate new catalysts, in the absence of detailed physicochemical knowledge, by using selection methods to search a library of molecules for functional variants. Both strategies have been applied, with considerable success, to the remodeling of existing ribozymes and the development of ribozymes with novel catalytic function. The two strategies are by no means mutually exclusive, and are best applied in a complementary fashion to obtain ribozymes with the desired catalytic properties.

Review, Tutorial↗