Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boundary layer analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Nonlinear Interaction of Detuned Instability Waves in Boundary-Layer Transition: Amplitude Equations

The non-equilibrium critical-layer analysis of a system of frequency-detuned resonant-triads is presented. In this part of the analysis, the system of partial differential critical-layer equations derived in Part I is solved analytically to yield the amplitude equations which are analyzed using a combination of asymptotic and numerical methods. Numerical solutions of the inviscid non-equilibrium oblique-mode amplitude equations show that the frequency-detuned self-interaction enhances the growth of the lower-frequency oblique modes more than the higher-frequency ones. All amplitudes become singular at the same finite downstream position. The frequency detuning delays the occurrence of the singularity. The spanwise-periodic mean-flow distortion and low-frequency nonlinear modes are generated by the critical-layer interaction between frequency-detuned oblique modes. The nonlinear mean flow and higher harmonics as well as the primary instabilities become as large as the base mean flow in the inviscid wall layer in the downstream region where the distance from the singularity is of the order of the wavelength scale.

Lee, Sang Soo↗

A new boundary-layer interaction techniques for separated flows

A new viscous-inviscid interation procedure is presented which is applicable to separated flows. The new procedure is simple, converges rapidly, and does not require numerical smoothing and underrelaxation at least in the cases computer thus far. Calculations are presented for the low-speed separated flow in the juncture region between an axisymmetric body and ting. The viscous computation is done with an inverse boundary-layer procedure which was previously developed. The inviscid computation is made with an axisymmetric transonic code called RAXBOD. The main advantage of the new interaction procedure is that it combines an inverse boundary-layer technique, which is applicable to separated flows, with an existing inviscid analysis code with only a slight boundary condition change required in the inviscid code.

Carter, J. E.↗

Heat Transfer to Surfaces of Finite Catalytic Activity in Frozen Dissociated Hypersonic Flow

The heat transfer due to catalytic recombination of a partially dissociated diatomic gas along the surfaces of two-dimensional and axisymmetric bodies with finite catalytic efficiencies is studied analytically. An integral method is employed resulting in simple yet relatively complete solutions for the particular configurations considered. A closed form solution is derived which enables one to calculate atom mass-fraction distribution, therefore catalytic heat transfer distribution, along the surface of a flat plate in frozen compressible flow with and without transpiration. Numerical calculations are made to determine the atom mass-fraction distribution along an axisymmetric conical body with spherical nose in frozen hypersonic compressible flow. A simple solution based on a local similarity concept is found to be in good agreement with these numerical calculations. The conditions are given for which the local similarity solution is expected to be satisfactory. The limitations on the practical application of the analysis to the flight of the blunt bodies in the atmosphere are discussed. The use of boundary-layer theory and the assumption of frozen flow restrict application of the analysis to altitudes between about 150,000 and 250,000 feet.

Chung, Paul M.↗

Boundary layer control for airships

An investigation is summarized of the aerodynamic principle of boundary layer control for nonrigid LTA craft. The project included a wind tunnel test on a BLC body of revolution at zero angle of attack. Theoretical analysis is shown to be in excellent agreement with the test data. Methods are evolved for predicting the boundary layer development on a body of revolution and the suction pumping and propulsive power requirements. These methods are used to predict the performance characteristics of a full-scale airship. The analysis indicates that propulsive power reductions of 15 to 25 percent and endurance improvements of 20 to 40 percent may be realized in employing boundary-layer control to nonrigid airships.

Pake, F. A.↗

Modeling Disturbance Dynamics in Transitional and Turbulent Boundary Layers

The dynamics of an ensemble of linear disturbances in boundary-layer flows at various Reynolds numbers is studied through an analysis of the transport equations for the mean disturbance kinetic energy and energy dissipation rate. Effects of adverse and favorable pressure-gradients on the disturbance dynamics are also included in the analysis. Unlike the fully turbulent regime where nonlinear phase scrambling of the fluctuations affects the flow field even in proximity to the wall, the early stage transition regime fluctuations studied here are influenced across the boundary layer by the solid boundary. In addition, the dominating dynamics in the disturbance kinetic energy equation is governed by the energy production, pressure-transport and viscous diffusion - also in contrast to the fully turbulent regime. For the disturbance dissipation rate, a dynamic balance exists between the destruction and diffusion of dissipation.

Grosch, C. E.↗

Theoretical analyses of Baroclinic flows

A stability analysis of a thin horizontal rotating fluid layer which is subjected to arbitrary horizontal and vertical temperature gradients is presented. The basic state is a nonlinear Hadley cell which contains both Ekman and thermal boundary layers; it is given in closed form. The stability analysis is based on the linearized Navier-Stokes equations, and zonally symmetric perturbations in the form of waves propagating in the meridional direction are considered. Numerical methods were used for the stability problem. It was found that the instability sets in when the Richardson number is close to unity and that the critical Richardson number is a non-monotonic function of the Prandtl number. Further, it was found that the critical Richardson number decreases with increasing Ekman number until a critical value of the Ekman number is reached beyond which the fluid is stable.

Antar, B.↗

Analysis of turbulence in the orthonormal wavelet representation

The usefulness of the wavelet transform for the analysis of turbulent flow fields is explored by examining the wavelet transform properties of a decomposition of turbulent velocity fields into modes that exhibit the localization in a wavenumber and physical space. The calculations are performed on 3D fields from direct numerical simulations of isotropic flow and homogeneous shear flow, and from measurements in two laboratory wind-tunnel experimental velocity signals (boundary layer and wake behind a circular cylinder). The analysis confirmed that there is strong spatial intermittency in nonlinear quantities; their mean spectral behavior results from a delicate balance between large positive and negative excursions. The wavelet analysis is a way to quantify these observations in a standardized fashion by using 'flow-independent eddies' to decompose the velocity field.

Meneveau, Charles↗

The evolution of Tollmien-Schlichting waves near a leading edge

The method of matched asymptotic expansions is used to study the generation of Tollmien-Schlichting waves by free-stream disturbances incident on a flat-plate boundary layer. Near the leading edge, the motion is governed by the unsteady boundary-layer equation, while farther downstream it is governed (to lowest order) by the Orr-Sommerfeld equation with slowly varying coefficients. It is shown that there is an overlap domain where the Tollmien-Schlichting wave solutions to the Orr-Sommerfeld equation and appropriate asymptotic solutions of the unsteady boundary-layer equation match, in the matched-asymptotic-expansion sense. The analysis explains how long-wavelength free-stream disturbances can generate Tollmien-Schlichting waves of much shorter wavelength. It also leads to a set of scaling laws for the asymptotic structure of the unsteady boundary layer.

Goldstein, M. E.↗

Nonlinear Nonmodal Analysis of Hypersonic Flow over Blunt Cones

The linear amplification of modal disturbances that lead to boundary-layer transition in two-dimensional/axisymmetric hypersonic configurations is strongly reduced by the presence of a blunt nosetip, and the mechanisms underlying the observed onset of transition over the cone frustum are currently unknown. Linear nonmodal analysis has shown that both planar and oblique traveling disturbances that peak within the entropy layer experience appreciable energy amplification for moderate to large nosetip bluntness. The present study extends the previous linear analysis by including the nonlinear effects. Specifically, the perturbation form of the 2D, harmonic Navier-Stokes equations (HNSE) are solved with a fully implicit formulation and the Newton-Raphson method. The increased number of degrees of freedom for the nonlinear system presents difficulties for solution strategies based on direct solution of the linearized system. Such difficulties are overcome by using the GMRES iterative method with a preconditioner corresponding to a simplified Jacobian without the cross derivative terms. The HNSE solver is verified by comparing with nonlinear parabolized stability equation (NPSE) results for the nonlinear evolution of planar waves in an incompressible Blasius boundary layer and in a Mach 6 flow over a blunt cone. Finally, nonlinear nonmodal results are presented for planar traveling disturbances over the blunt cone. The nonmodal analysis demonstrates that entropy-layer disturbances generated close to the nose tip can seed the amplification of higher frequency Mack’s second-mode instabilities further downstream.

boundary layer transition↗

Evaluation of the Antarctic Boundary Layer Thermodynamic Structure In MERRA2 Using Dropsonde Observations from the Concordiasi Campaign

Recent high-resolution dropsonde observations from the 2010 Concordiasi field campaign in austral spring season show that surface-based inversions (SBIs) over Antarctica are frequently eroded, with well-mixed boundary layers occurring 33% and 18% of the time in West and East Antarctica, respectively. In this study, using the dropsonde observations, we evaluate the performance of the Modern-Era Retrospective analysis for Research and Applications, version 2 (MERRA2) in representing the Antarctic boundary layer thermodynamic structure. Results show that MERRA2 has a good overall representation of the Antarctic surface stability and correctly predicts 82% of the SBIs. However, an under prediction of less stable boundary layer occurrence, especially over the elevated East Antarctic plateau, is favored during conditions of increased lower tropospheric stability associated with model dynamics, indicating difficulty in parameterizing turbulence in very stable boundary layers. In addition, a lower tropospheric cool bias (first model level and above) is observed in the MERRA2 reanalysis, especially over West Antarctica, which amplifies in the boundary layer during mixed conditions. The near-surface cold bias is most pronounced when the model fails to predict mixed layers over West Antarctica, and is expected to negatively impact the representation of surface energy budget and melt processes.

Manisha Ganeshan↗

Direct measurements and analysis of skin friction and cooling downstream of multiple flush-slot injection into a turbulent Mach 6 boundary layer

Experiments were conducted to determine the reduction in surface skin friction and the effectiveness of surface cooling downstream of one to four successive flush slots injecting cold air at an angle of 10 deg into a turbulent Mach 6 boundary layer. Data were obtained by direct measurement of surface shear and equilibrium temperatures, respectively. Increasing the number of slots decreased the skin friction, but the incremental improvement in skin-friction reduction decreased as the number of slots was increased. Cooling effectiveness was found to improve, for a given total mass injection, as the number of slots was increased from one to four. Comparison with previously reported step-slot data, however, indicated that step slots with tangential injection are more effective for both reducing skin friction and cooling than the present flush-slot configuration. Finite-difference predictions are in reasonable agreement with skin-friction data and with boundary-layer profile data.

Howard, F. G.↗

Nonlinear Nonmodal Analysis of Hypersonic Flow over Blunt Cones

The linear amplification of modal disturbances that lead to boundary-layer transition in two-dimensional/axisymmetric hypersonic configurations is strongly reduced by the presence of a blunt nosetip, and the mechanisms underlying the observed onset of transition over the cone frustum are currently unknown. Linear nonmodal analysis has shown that both planar and oblique traveling disturbances that peak within the entropy layer experience appreciable energy amplification for moderate to large nosetip bluntness. The present study extends the previous linear analysis by including the nonlinear effects. Specifically, the perturbation form of the 2D, harmonic Navier-Stokes equations (HNSE) are solved with a fully implicit formulation and the Newton-Raphson method. The increased number of degrees of freedom for the nonlinear system presents difficulties for solution strategies based on direct solution of the linearized system. Such difficulties are overcome by using the GMRES iterative method with a preconditioner corresponding to a simplified Jacobian without the cross derivative terms. The HNSE solver is verified by comparing with nonlinear parabolized stability equation (NPSE) results for the nonlinear evolution of planar waves in an incompressible Blasius boundary layer and in a Mach 6 flow over a blunt cone. Finally, nonlinear nonmodal results are presented for planar traveling disturbances over the blunt cone. The nonmodal analysis demonstrates that entropy-layer disturbances generated close to the nose tip can seed the amplification of higher frequency Mack’s second-mode instabilities further downstream.

boundary layer transition↗

Orbiter Boundary Layer Transition Prediction Tool Enhancements

Updates to an analytic tool developed for Shuttle support to predict the onset of boundary layer transition resulting from thermal protection system damage or repair are presented. The boundary layer transition tool is part of a suite of tools that analyze the local aerothermodynamic environment to enable informed disposition of damage for making recommendations to fly as is or to repair. Using mission specific trajectory information and details of each d agmea site or repair, the expected time (and thus Mach number) of transition onset is predicted to help define proper environments for use in subsequent thermal and stress analysis of the thermal protection system and structure. The boundary layer transition criteria utilized within the tool were updated based on new local boundary layer properties obtained from high fidelity computational solutions. Also, new ground-based measurements were obtained to allow for a wider parametric variation with both protuberances and cavities and then the resulting correlations were calibrated against updated flight data. The end result is to provide correlations that allow increased confidence with the resulting transition predictions. Recently, a new approach was adopted to remove conservatism in terms of sustained turbulence along the wing leading edge. Finally, some of the newer flight data are also discussed in terms of how these results reflect back on the updated correlations.

Berry, Scott A.↗

A Supersonic Tunnel for Laser and Flow-Seeding Techniques

A supersonic wind tunnel with flow conditions of 3 lbm/s (1.5 kg/s) at a free-stream Mach number of 2.5 was designed and tested to provide an arena for future development work on laser measurement and flow-seeding techniques. The hybrid supersonic nozzle design that was used incorporated the rapid expansion method of propulsive nozzles while it maintained the uniform, disturbance-free flow required in supersonic wind tunnels. A viscous analysis was performed on the tunnel to determine the boundary layer growth characteristics along the flowpath. Appropriate corrections were then made to the contour of the nozzle. Axial pressure distributions were measured and Mach number distributions were calculated based on three independent data reduction methods. A complete uncertainty analysis was performed on the precision error of each method. Complex shock-wave patterns were generated in the flow field by wedges mounted near the roof and floor of the tunnel. The most stable shock structure was determined experimentally by the use of a focusing schlieren system and a novel, laser based dynamic shock position sensor. Three potential measurement regions for future laser and flow-seeding studies were created in the shock structure: deceleration through an oblique shock wave of 50 degrees, strong deceleration through a normal shock wave, and acceleration through a supersonic expansion fan containing 25 degrees of flow turning.

Bruckner, Robert J.↗

TRANSPORT OF HEAT, WATER VAPOR AND CARBON DOXIDE BY LONG PERIOD EDDIES IN THE STABLE BOUNDARY LAYER

The vertical transport of heat and trace chemicals for a night in April has been studied with a wavelet analysis and conventional one-hour averages. It was found that for the night of April 20, 2009, turbulent kinetic energy, heat and trace chemicals were transported directed downward from the jet core. The most significant periods for this transport were less than 5 minutes and greater than one hour with intermittent transport taking place in the 5 min to 1 hour time frame. The nocturnal boundary layer is characterized by turbulent intermittency, long period oscillations, and a slow approach to equilibrium, (Mahrt, 1999). Although turbulence is usually maintained by surface friction, downward transport from low-level jets can also play an important role in turbulence maintenance and in the transport of scalars, Mahrt (1999), Banta et al. (2006). The eddy covariance flux measurement technique assumes continuous turbulence which is unusual in the stable boundary because significant flux transport occurs via turbulent eddies whose periods are long compared with the averaging time (Goulden et al., 1996). Systematic error in eddy flux measurements is attributed mainly to the neglect of long period eddies. Banta et al. (2006) noted that observations of turbulence below the low level jet suggested that while upward transport of turbulence kinetic energy (TKE) is common, downward transport from the jet can also occur. They found that in the CASES 99 experiments that turbulence scaled well with the strength of the low-level jet, and that surface cooling was more important than surface roughness. Because nocturnal turbulence is intermittent and non-stationary, the appropriate averaging time for calculation of TKE and EC fluxes is not obvious. Wavelet analysis is, thus, a more suitable analysis tool than conventional Fourier analysis.

54 ENVIRONMENTAL SCIENCES↗

Characterisation of Ga-coated and Ga-brazed aluminium

This work is devoted to the brazing of aluminium using liquid gallium. Gallium was deposited on aluminium samples at {approx} 50 Degree-Sign C using a liquid gallium 'polishing' technique. Brazing was undertaken for 30 min at 500 Degree-Sign C in air. EDS (Energy Dispersive X-ray Spectroscopy) and AES (Auger Electron Spectroscopy) characterisation of Ga-coated samples has shown that the Ga surface layer thickness is of ten (or a few tens of) nanometres. Furthermore, aluminium oxide layer (Al{sub 2}O{sub 3}) was shown to be 'descaled' during Ga deposition, which ensures good conditions for further brazing. Cross-section examination of Ga-coated samples shows that liquid gallium penetrates into the aluminium grain boundaries during deposition. The thickness of the grain boundary gallium film was measured using an original EDS technique and is found to be of a few tens of nanometres. The depth of gallium grain boundary penetration is about 300 {mu}m at the deposition temperature. The fracture stress of the brazed joints was measured from tensile tests and was determined to be 33 MPa. Cross-section examination of brazed joints shows that gallium has fully dissolved into the bulk and that the joint is really autogenous. - Highlights: Black-Right-Pointing-Pointer Aluminium can be brazed using liquid gallium deposited by a 'polishing' technique. Black-Right-Pointing-Pointer The aluminium oxide layer is 'descaled' during liquid Ga 'polishing' deposition. Black-Right-Pointing-Pointer EDS can be used for determination of surface and grain boundary Ga film thickness. Black-Right-Pointing-Pointer The surface and grain boundary Ga film thickness is of a few tens of nm. Black-Right-Pointing-Pointer Surface and grain boundary gallium dissolves in the bulk during brazing.

36 MATERIALS SCIENCE↗

Laminar free convection over two-dimensional bodies with uniform surface heat flux

A general analysis is presented of the steady nondissipative constant-property laminar boundary layer flow over a two-dimensional body of uniform surface heat flux situated in an infinite ambient fluid of undisturbed temperature. The analysis is then applied to a long horizontal circular cylinder. Numerical solutions to the universal functions associated with the first two terms in the derived series are given for Prandtl numbers 0.7, 1, 3, 5, 7, and 10. The results are compared with those obtained by Koh (1964) whose method is patterned after the Blasius-Frossling procedure for forced convection flow. The study reveals that Wilks' (1972) analysis concerning the external natural convection about two-dimensional bodies with constant heat flux is in error.

Lin, F. N.↗

Effect of Mach Number on the Flow and Application of Compressibility Corrections in a Two-Dimensional Subsonic-Transonic Compressor Cascade Having Varied Porous-Wall Suction at the Blade Tips

A cascade of 65-(12)10 compressor blades was tested at one geometric setting over a range of inlet Mach number from 0.12 to 0.89. Two groups of data are presented and compared: the first from the cascade operating conventionally with no boundary-layer control, and the second with the boundary layer controlled by a combination of upstream slot suction and porous-wall suction at the blade tips. A criterion for two-dimensionality was used to specify the degree of boundary-layer control by suction to be applied. The data are presented and an analysis is made to show the effect of Mach number on turning angle, blade wake, pressure distribution about the blade profile and static-pressure rise. The influence of boundary-layer control on these parameters as well as on the secondary losses is illustrated. A system of correlating the measured static-pressure rise through the cascade with the theoretical isentropic values is presented which gives good agreement with the data. The pressure distribution about the blade profile for an inlet Mach number of 0.21 is corrected with the Prandtl-Glauert, Karman-Tsien, and vector-mean velocity - contraction coefficient compressibility correction factors to inlet Mach numbers of 0.6 and 0.7. The resulting curves are compared with the experimental pressure distributions for inlet Mach numbers of 0.6 and 0.7 so that the validity of applying the three corrections can be evaluated.

Briggs, William B.↗