Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “XRD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Impact of Synthetic Parameters on Structure and Electrochemistry of High-Entropy Layered Oxide LiNi 0.2 Co 0.2 Mn 0.2 Al 0.2 Fe 0.2 O 2

Here, this study explored a high-entropy layered oxide (HELO), LiNi 0.2 Co 0.2 Mn 0.2 Al 0.2 Fe 0.2 O 2 , prepared by coprecipitation followed by heat treatment. Coprecipitation yielded a kinetically favored product, and the subsequent heat treatment under various temperatures and times allowed tuning the material toward more thermodynamically favored structures. Refinement of X-ray powder diffraction (XRD) revealed that after 450 °C treatment, ~12% of the Ni 2+ in the structure was located within the lithium cation layer. After heat treatment at 600, 700, and 800 °C, there was a continued decrease of Ni 2+ in the lithium cation layer to 9.3, 6.3, and 3.7%, respectively. Longer heat treatment times at 800 °C decreased the level to 2.5%. Electrochemical behavior was evaluated by cyclic voltammetry, galvanostatic cycling, rate capability testing, and electrochemical impedance spectroscopy, where increased loaded voltage, functional capacity, rate capability, and decreased impedance were observed for samples treated at higher temperatures with lower cation mixing. X-ray absorption near edge spectroscopy (XANES) data indicated that the redox activity of Ni and Co was dominant in the electrochemistry, while the participation of Mn or Fe was minimal. The level of Ni oxidation state change between charge and discharge related to the heat treatment temperature where the samples with high cation mixing showed lower capacity consistent with some Ni 3+ in the transition metal layer inaccessible for electron transfer. Longer heat treatment times at 800 °C did not continue to provide a benefit in electrochemical function even with some additional reduction in cation mixing.

25 ENERGY STORAGE↗
DOE OSTI2025

WO 3 /CuWO 4 Ratio Controls Open-Circuit Photovoltage and Photocurrent in Type II Heterojunction Solar Fuel Photoelectrodes

WO 3 /CuWO 4 photoelectrodes for the oxygen evolution reaction benefit from a type II heterojunction for charge separation. However, the impact of the WO 3 /CuWO 4 ratio on the photocurrent and the photovoltage is not clear. To probe the effect of composition, Cu x W 1-x O y thin films with variable W:Cu ratio were prepared on FTO by reactive magnetron co-sputtering of W and Cu, followed by air annealing at 500ºC. EDS, XRD, Rietveld refinement, and Raman spectroscopy confirm the presence of crystalline WO 3 and CuWO 4 in the W rich films and increasing amounts of amorphous copper oxides in the Cu rich films. Bandgaps were determined by optical absorption spectroscopy, surface photovoltage spectroscopy (SPS), and photoaction spectra and are found to decrease from 2.7 eV to 1.2 eV with increasing copper oxide content. SPS reveals n-type semiconductor photoanode behavior for WO 3 /CuWO 4 samples and p-type photocathode behavior for CuO x rich films. Photoelectrochemical experiments confirm stable water oxidation with Faraday efficiency near unity for all W rich films and photocurrents that are increasing with CuWO 4 content. Optimal performance is seen for WO 3 /CuWO 4 mixed phases containing 47-75 mass% CuWO 4 . These compositions maximize charge separation at the type II heterojunction interface between the two materials. Additionally, according to incident photon to current efficiency (IPCE) data, the WO 3 improves photon conversion below 350 nm, while CuWO 4 improves conversion at 450-525 nm. Overall, this work shows for the first time how the WO 3 /CuWO 4 ratio controls the photovoltage and the photocurrent in type II heterojunction solar fuel photoelectrodes, and how copper oxides in the copper rich films severely degrade the performance. Furthermore, these results are useful in the context of bulk-heterojunction electrodes for the conversion of solar energy into fuels.

CuWO4↗
DOE OSTI2025

Xerogel-Derived Ni Electrocatalysts for the Hydrogen Evolution Reaction in Alkaline Media

Anion exchange membrane water electrolyzers (AEMWEs) represent a promising technology for hydrogen production. The big advantage of the technology is that it allows for the use of platinum group metal-free (PGM-free) electrocatalysts at both electrodes, including catalysts for the hydrogen evolution reaction (HER) at the cathode. In addition to fulfilling the cost requirement, PGM-free HER catalysts need to meet the activity and durability targets of the AEMWEs. Here, in this work, we developed several carbon-supported, xerogel-derived nickel (Ni) HER electrocatalysts and evaluated the effect of various synthesis conditions, such as the type of carbon support, Ni-to-carbon ratio, and heat-treatment temperature and time, on their performance. Scanning transmission electron microscopy combined with energy-dispersive X-ray spectroscopy (STEM-EDS), X-ray diffraction spectroscopy (XRD), and X-ray photoelectron spectroscopy (XPS) revealed the formation of Ni nanoparticles with an oxygen-rich layer on the outside. Durability of the best-performing catalyst was assessed via a constant-current hold at 10 mA cm –2 over 100 h. This catalyst was found to be more active and durable than the reference PGM-free material, a commercial Ni catalyst supported on a Vulcan XC-72. The catalyst was also tested in the cathode of a fully PGM-free AEMWE, allowing to reach 1.90 V (1.84 V HFR-free) at 1 A cm –2 at 80 °C.

08 HYDROGEN↗
DOE OSTI2026

Machine-Learning-Driven Discovery of Water Splitting BaFe 2 O 4 and Human-in-the-Loop Improvement via Al-Substitution for Increased Thermal Stability

Thermochemical hydrogen (TCH) production offers a promising method for converting thermal energy into hydrogen fuel through heat-driven redox cycles of metal oxides. Here, in this work a defect graph neural network (dGNN) was used to predict oxygen vacancy formation energies ΔH V O combined with Materials Project predictions of oxygen chemical potential stability to screen candidate oxides via high-throughput database analysis. BaFe 2 O 4 was identified as a promising material for experimental validation based on its predicted ΔH V O , oxygen chemical potential stability range, and potential for tunable substitutions to improve thermal properties. Experimental validation using thermogravimetric analysis (TGA), stagnation flow reactor (SFR), X-ray diffraction (XRD), and electron microscopy confirmed positive water-splitting behavior but also revealed limitations in thermal stability under aggressive reduction conditions. To address this, a human-in-the-loop modification strategy was employed introducing Al substitution in BaFe 2–x Al x O 4 ; this modification improves thermal stability, alters the crystal structure and enhances overall performance. These results demonstrate a combined computational and experimental workflow in which machine learning accelerates identification of promising candidates, while targeted experimental design enables optimization of functional performance. This approach advances the development of robust, cost-effective TCH materials and highlights the importance of integrating data-driven discovery with human-guided materials design in paving the way for scalable hydrogen production technologies.

organic↗
DOE OSTI2021

High-Capacity Aqueous Storage in Vanadate Cathodes Promoted by the Zn-Ion and Proton Intercalation and Conversion–Intercalation of Vanadyl Ions

Aqueous Zn-ion batteries (AZIBs) are promising alternatives to lithium-ion batteries in stationary storage. However, limited storage capacity and cyclic life impede their large-scale implementation. In this study, we report reversible electrochemical insertion of multi-ions into sodium vanadate (NaV 3 O 8 ) cathode materials for AZIBs, achieving a maximum storage capacity of 450 mAh g –1 at 0.05 A g –1 and a capacity retention of 82% after 500 cycles at 0.4 A g –1 . In addition to Zn 2+ and H + insertion, in situ X-ray diffraction (XRD) and X-ray absorption spectroscopy (XAS) collectively provide explicit evidence on vanadyl ions (VO 2+ ) conversion–intercalation at the NaV 3 O 8 cathode, showing the deintercalation of VO 2+ from NaV 3 O 8 and the consequent conversion of VO 2+ into V 2 O 5 on charging, and vice versa on discharging. Our study is the first to report on the cation conversion–intercalation mechanism in AZIBs. This reversible multi-ion storage mechanism provides a design principle for developing high-capacity aqueous electrode materials by engaging both the intercalation and conversion of charge carriers.

25 ENERGY STORAGE↗
DOE OSTI2021

Impact of Charge Voltage on Factors Influencing Capacity Fade in Layered NMC622: Multimodal X-ray and Electrochemical Characterization

Ni-rich NMC is an attractive Li-ion battery cathode due to its combination of energy density, thermal stability, and reversibility. While higher delivered energy density can be achieved with a more positive charge voltage limit, this approach compromises sustained reversibility. Improved understanding of the local and bulk structural transformations as a function of charge voltage, and their associated impacts on capacity fade are critically needed. Through simultaneous operando synchrotron X-ray diffraction (XRD) and X-ray absorption spectroscopy (XAS) of cells cycled at 3–4.3 or 3–4.7 V, this study presents an in-depth investigation into the effects of voltage window on local coordination, bulk structure, and oxidation state. These measurements are complemented by ex situ X-ray fluorescence (XRF) mapping and scanning electrochemical microscopy mapping (SECM) of the negative electrode, X-ray photoelectron spectroscopy (XPS) of the positive electrode, and cell level electrochemical impedance spectroscopy (EIS). Initially, cycling between 3 and 4.7 V leads to greater delivered capacity due to greater lithium extraction, accompanied by increased structural distortion, moderately higher Ni oxidation, and substantially higher Co oxidation. Continued cycling at this high voltage results in suppressed Ni and Co redox, greater structural distortion, increased levels of transition metal dissolution, higher cell impedance, and 3× greater capacity fade.

capacity fading mechanisms↗
DOE OSTI2022

Formation of a Secondary Phase in Thermally Evaporated MAPbI 3 and Its Effects on Solar Cell Performance

Thermal evaporation is a promising deposition technique to scale up perovskite solar cells (PSCs) to large areas, but the lack of understanding of the mechanisms that lead to high-quality evaporated methylammonium lead triiodide (MAPbI 3 ) films gives rise to devices with efficiencies lower than those obtained by spin coating. Here this work investigates the crystalline properties of MAPbI 3 deposited by the thermal coevaporation of PbI 2 and MAI, where the MAI evaporation rate is controlled by setting different temperatures for the MAI source and the PbI 2 deposition rate is controlled with a quartz crystal microbalance (QCM). Using grazing incident wide-angle X-ray scattering (GIWAXS) and X-ray diffraction (XRD), we identify the formation of a secondary orthorhombic phase (with a Pnma space group) that appears at MAI source temperatures below 155 °C. With synchrotron-based X-ray fluorescence (XRF) microscopy, we show that the changes in crystalline phases are not necessarily due to changes in stoichiometry. The films show a stochiometric composition when the MAI source is heated between 140 to 155 °C, and the samples become slightly MAI rich at 165 °C. Increasing the MAI temperature beyond 165 °C introduces an excess of MAI in the film, which promotes the formation of films with low crystallinity that contain low-dimensional perovskites. When they are incorporated in solar cells, the films deposited at 165 °C result in the champion power conversion efficiency, although the presence of a small amount of low-dimensional perovskite may lead to a lower open-circuit voltage. We hypothesize that the formation of secondary phases in evaporated films limits the performance of PSCs and that their formation can be suppressed by controlling the MAI source temperature, bringing the film toward a phase-pure tetragonal structure. Control of the phases during perovskite evaporation is therefore crucial to obtain high-performance solar cells.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Controlling the Magneto-Optical Response in Ultrathin Films of EuO 1– x via Interface Engineering with Ferroelectric BaTi 2 O 5

Utilizing pulsed laser deposition, a film of EuO 1–x was deposited onto a Si(001) substrate with MgO buffer and compared to the same heterostructure with an additional BaTi 2 O 5 thin film on top of the EuO 1–x surface. X-ray diffraction (XRD) indicates the films crystallize into a preferred EuO(111) orientation; it also reveals the clear presence of EuSi 2 , which suggests Si or Eu diffuses across the MgO buffer layer. EuO 1–x films exhibit a ferromagnetic (FM) signature and temperature-dependent exchange bias, indicated by MOKE measurements, suggesting the presence of a magnetic order well above the EuO Curie temperature with possible origins in charge carrier density near the interface. In comparison, an antiferromagnetic character persists well above the EuO Curie temperature of 69 K and the enhanced Curie temperature of 150 K for BaTi 2 O 5 films grown on the EuO 1–x films. Furthermore, the antiferromagnetic behavior is not seen in thicker EuO 1–x thin films when integrated with other ferroelectric (FE) phases of the BaO–TiO 2 system, suggesting an origin in the perturbed charge population at the BaTi 2 O 5 /EuO 1–x interface.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Enhanced Switching Reliability of Hf 0.5 Zr 0.5 O 2 Ferroelectric Films Induced by Interface Engineering

Ferroelectric materials have been widely researched for applications in memory and energy storage. Among these materials and benefiting from their excellent chemical compatibility with complementary metal–oxide–semiconductor (CMOS) devices, hafnia-based ferroelectric thin films hold great promise for highly scaled semiconductor memories, including nonvolatile ferroelectric capacitors and transistors. However, variation in the switched polarization of this material during field cycling and a limited understanding of the responsible mechanisms have impeded their implementation in technology. Here, we show that ferroelectric Hf 0.5 Zr 0.5 O 2 (HZO) capacitors that are nearly free of polarization “wake-up”─a gradual increase in switched polarization as a function of the number of switching cycles─can be achieved by introducing ultrathin HfO 2 buffer layers at the HZO/electrodes interface. High-resolution transmission electron microscopy (HRTEM) reveals crystallite sizes substantially greater than the film thickness for the buffer layer capacitors, indicating that the presence of the buffer layers influences the crystallization of the film (e.g., a lower ratio of nucleation rate to growth rate) during postdeposition annealing. This evidently promotes the formation of a polar orthorhombic (O) phase in the as-fabricated buffer layer samples. Synchrotron X-ray diffraction (XRD) reveals the conversion of the nonpolar tetragonal (T) phase to the polar orthorhombic (O) phase during electric field cycling in the control (no buffer) devices, consistent with the polarization wake-up observed for these capacitors. The extent of T–O transformation in the nonbuffer samples is directly dependent on the duration over which the field is applied. Here these results provide insight into the role of the HZO/electrodes interface in the performance of hafnia-based ferroelectrics and the mechanisms driving the polarization wake-up effect.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Low Melting Temperature Gallium–Indium Liquid Metal Anode for Solid-State Li-Ion Batteries

Solid-state Li-ion batteries are attracting attention for their enhanced safety features, higher energy density, and broader operational temperature range compared to systems based on liquid electrolytes. However, current solid-state Li-ion batteries face performance challenges, such as suboptimal cycling and poor rate capabilities, often due to inadequate interfacial contact between the solid electrolyte and electrodes. To address this issue, we incorporated a gallium–indium (Ga–In) liquid metal as the anode in a solid-state Li-ion battery setup, employing Li 6 PS 5 Cl as the solid electrolyte. Operating at room temperature, this configuration achieved an initial capacity of 389 mAh g –1 and maintained 88% of this capacity after 30 cycles at a 0.05 C rate. It also demonstrated a capacity retention of 66% after 500 cycles at a 0.5 C rate. In comparison to solid anode materials, such as tin, the Ga–In liquid metal exhibited superior cycling stability and rate capacity, which is due to the self-healing and fluid properties of the alloy that ensure stable interfacial contact with solid electrolytes. In situ X-ray diffraction (XRD) and ex situ scanning electron microscope (SEM) analyses revealed that indium does not directly participate in the lithiation/delithiation process. Instead, it helps maintain the alloy’s low melting point, facilitating its return to a liquid state after delithiation. In a comparative analysis of stack pressure during cycling in cells utilizing Ga–In liquid metal and tin, the Ga–In liquid metal cell demonstrated an ability to buffer pressure increases associated with deformation. In conclusion, these findings suggest a promising approach for enhancing solid-state batteries by integrating liquid metal anodes, which improve interfacial contact and stability.

Alloys↗
DOE OSTI2024

Sputter-Coated TiO 2 Films as Passivation and Hole Transfer Layers for Improved Energy Conversion with Solar Fuel WO 3 /CuWO 4 Photoanodes

Atomic layer deposited (ALD) “leaky” TiO 2 have gained interest as charge-selective protection layers for semiconductor solar fuel electrodes. Here we demonstrate the use of sputter-deposited TiO 2 layers as hole selective contacts for WO 3 /CuWO 4 type 2 heterojunction water oxidation photoanodes for the first time. TiO 2 protection layers with varying thicknesses (2 to 128 nm) were deposited using the RF magnetron sputtering technique. The resulting TiO 2 films are amorphous based on Raman spectroscopy and powder XRD. Photoelectrochemical scans and Vibrating Kelvin probe photovoltage spectroscopy show that 2-8 nm TiO 2 layers nearly double the photocurrent to 0.97 mA cm -2 under AM 1.5 illumination (19% AQE at 350 nm), increase the surface photovoltage signal by 25%, and increase the WO 3 /CuWO 4 bandgap. These effects can be attributed to the selectivity of TiO 2 for photoholes. Additionally, SPV data suggest that TiO 2 overlayers suppress copper-based surface recombination defects. Reduced photocurrent and the photovoltage are seen in thicker TiO 2 films (16 to 128 nm) as a result of an increasing hole transfer resistance and because of light shading effects according to photoaction spectra. The TiO 2 films also improve the stability of the WO 3 /CuWO 4 photoelectrodes, allowing nearly constant O 2 evolution over 3 hours after an initial 20-35% loss. Overall, this work establishes RF magnetron sputtering as a useful method to install amorphous TiO 2 passivation layers for improved WO 3 /CuWO 4 solar fuel photoelectrodes. Furthermore, we show how the combination of PEC with SPV measurements provides insight into the function of the TiO 2 coatings.

CuWO4↗
DOE OSTI2024

Elucidating the Discharge Behavior of Aqueous Zinc Sulfur Batteries in the Presence of Molybdenum(IV) Chalcogenide Catalyst: The Criticality of Interfacial Electrochemistry

The aqueous zinc-sulfur battery holds promise for significant capacity and energy density with low cost and safe operation based on environmentally benign materials. However, it suffers from the sluggish kinetics of the conversion reaction. Here, we highlight the efficacy of molybdenum(IV) sulfide (MoS 2 ) to reduce the overpotential of S-ZnS conversion in aqueous electrolytes and study the discharge products formed at the solid-solid and solid-liquid interfaces using experimental and theoretical approaches. Specifically, the MoS 2 -catalyzed electrochemical conversion reaction is characterized via ex situ X-ray diffraction (XRD), transmission electron microscopy (TEM) with energy dispersive spectroscopy (EDS), Raman spectroscopy, synchrotron-based Mo K-edge X-ray absorption spectroscopy (XAS), and in situ synchrotron-based X-ray computed tomography (XCT). Additionally, operando synchrotron-based S K-edge XAS and X-ray fluorescence (XRF) maps are collected to determine the spatial evolution of sulfur-based species at the electrode-electrolyte interface. Further, coupling the operando S K-edge XAS data with the simulated spectra and fitting the data suggested a possible ZnS 2 intermediate phase.

25 ENERGY STORAGE↗
DOE OSTI2024

Facile Interfacial Reduction Suppresses Redox Chemical Expansion and Promotes the Polaronic to Ionic Transition in Mixed Conducting (Pr,Ce)O 2−δ Nanoparticles

Mixed ionic/electronic conductors (MIECs) are essential components of solid-state electrochemical devices, such as solid oxide fuel/electrolysis cells. For efficient performance, MIECs are typically nanostructured, to enhance the reaction kinetics. However, the effect of nanostructuring on MIEC chemo-mechanical coupling and transport properties, which also impact cell durability and efficiency, has not yet been well understood. Here, in this work, Pr 0.2 Ce 0.8 O 2−δ (PCO20) nanopowders were prepared by coprecipitation, then sintered in a modified dilatometer at three different temperatures (600, 725, and 850 °C) for microstructure evolution, resulting in three samples with different average particle sizes (23, 30, and 53 nm). The chemical strain and electronic/ionic conductivity were then measured simultaneously on stable nanostructures in four isotherms from 550 to 400 °C with steps in pO 2 (1 to 10 –4 atm O 2 ). A microcrystalline bar was prepared and measured for comparison. Particle size reduction led to a monotonically decreasing isothermal redox chemical strain, confirmed by in situ high-temperature, controlled-atmosphere XRD measurements. The corresponding conductivity measurements provided defect chemical insight into the particle size-dependent chemical expansion behavior. The significant weakening of the pO 2 dependence and decreased activation energy for electrical conduction with decreasing particle size indicated a decrease in the reduction enthalpy of PCO, shifting the transition from (Pr) polaronic to ionic behavior to higher pO 2 . STEM-EELS measurements confirmed the majority of Pr was reduced to 3+ in the nanoparticles, while Ce remained 4+. These results demonstrate suppression of deleterious chemical expansion and tailoring of the dominant charge carrier simply through controlling the particle size, providing insights for MIEC microstructural design.

ceria↗
DOE OSTI2025

Comparative Study of Vinylene Carbonate and Lithium Difluoro(oxalate)borate Additives in a SiO x /Graphite Anode Lithium-Ion Battery in the Presence of Fluoroethylene Carbonate

The SiO x /graphite composite is recognized as a promising anode material for lithium-ion batteries (LIBs), owing to the high theoretical capacity of SiO x combined with the excellent stability of graphite. However, the inherent disadvantage of volume expansion in silicon-based anodes places significant challenges on the solid electrolyte interphase (SEI) and severely degrades the electrochemical performance. Rational formulation of electrolyte, including its additives, is crucial in accommodating and optimizing the composition of the SEI and enhancing the cell performance. In this work, we present a comparative study of vinylene carbonate (VC) and lithium difluoro(oxalate)borate (LiDFOB) additives combined with fluoroethylene carbonate (FEC) in the electrolyte for SiO x /graphite∥LiNi 1–x–y–z Co x Mn y Al z O 2 full cells. VC outperformed LiDFOB as an additive, delivering higher capacity cycling, higher Coulombic efficiency, and better cycle stability up to 400 cycles. XPS and impedance analyses reveal that LiDFOB contributed to SEI/CEI with both a lower proportion of LiF and a higher proportion of poly(VC), which tended to produce higher cell impedance. XRD and XANES further indicated that using the LiDFOB additive, the NCMA cycled to a shallower degree than that of the VC additive. Although the VC additive maintained a higher capacity up to 400 cycles, microstrain and SEM analyses show a higher strained NCMA along with clear evidence of cracking over the surface of the NCMA particle in VC-based electrolyte but not in LiDFOB. In conclusion, this suggests that the negative influence of LiDFOB at the anode (inferior SEI) supersedes the negative impact of both a cracked NCMA and a deeper cycled NCMA and SiO x -based anode.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Ultrafast Reactive Laser Sintering of Highly Conductive Garnet-Type LLZTO Solid Electrolytes

Rapid and scalable fabrication of garnet-type solid electrolytes remains a major challenge for the practical deployment of lithium metal batteries. Here, we report reactive laser sintering (RLS) as an ultrafast and potentially scalable strategy for fabricating garnet-type Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO) solid electrolytes. RLS of LLZTO enables simultaneous reaction and densification, achieving ∼95% relative density while minimizing lithium loss and suppressing secondary phase formation. Compared to conventional furnace sintering, RLS promotes enhanced grain growth and improved densification, leading to improved ionic conductivity (0.36 ± 0.08 mS cm −1 ) while maintaining comparable activation energies for Li + transport. Structural characterization by X-ray diffraction (XRD), Raman spectroscopy, and solid-state 6 Li/ 7 Li NMR confirms the formation of cubic garnet LLZTO with homogeneous microscale elemental distribution. In addition, nanoindentation measurements demonstrate that RLS preserves the mechanical properties of the garnet framework despite ultrafast localized thermal processing. By integrating simultaneous reaction and densification with tunable microstructural control, reactive laser sintering provides a promising manufacturing pathway for high-performance garnet solid electrolytes toward next-generation solid-state batteries.

CO2 laser↗
DOE OSTI2020

Hydrous Nickel–Iron Turnbull’s Blue as a High-Rate and Low-Temperature Proton Electrode

Proton batteries are emerging as a promising solution for energy storage; however, their development has been hindered by the lack of suitable cathode materials. Herein, a hydrous Turnbull’s blue analogue (TBA) of Ni[Fe(CN) 6 ] 2/3 ·4H 2 O has been investigated as a viable proton cathode. Particularly, it shows an extremely high rate performance up to 6000 C (390 A g –1 ) at room temperature and delivers good capacity values at a low temperature of -40 °C in an aqueous electrolyte. The excellent rate capability is also amenable to high mass loadings of 10 mg cm –2 . Such fast and low-temperature rate behavior likely stems from the fast proton conduction that is afforded by the Grotthuss mechanism inside the TBA structure. Furthermore, advanced characterization, including in operando synchrotron X-ray diffraction (XRD), and X-ray absorption near-edge structure (XANES) were employed to understand the changes of crystal structures and the oxidation-states of metal elements of the electrodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Liquid–Solid Mixtures of Ga Metal Infused with Cu Microparticles and Nanoparticles for Microscale and Nanoscale Patterning of Solid Metals at Room Temperature

This paper demonstrates and characterizes a simple ink for nanopatterning of solid metallic structures under ambient conditions by taking advantage of the low melting point of gallium and its affinity to form intermetallics with other metals. Bare copper micro- and nanoparticles readily mix with liquid gallium near room temperature to form a paste that ultimately amalgamates into a dense solid when mixed at the appropriate concentration ratios. The paste has sufficient shelf life that can be extruded from a nozzle at modest temperatures to form solid three-dimensional (3D) shapes. Additionally, the paste can be molded at room temperature to replicate feature sizes ranging from a few millimeters down to hundreds of nanometers. In situ X-ray diffraction (XRD) and thermo-mechanical analysis (TMA) data show gallium and copper readily interdiffuse to form the thermodynamically expected intermetallic phase. We describe the capabilities and limitations of a simple way to pattern solid metals in an additive fashion (syringe-based extrusion) and with high resolution (molding) at or near room temperature. Here, the use of a paste that solidifies provides a novel route for 3D printing of solid metals at ambient temperatures as well as the creation of micro- and nanostructured metallic surfaces that may be useful for optics, non-wetting surfaces, or electronic microcomponents.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microwave-Assisted Synthesis of Cu@IrO 2 Core-Shell Nanowires for Low-Temperature Methane Conversion

A facile microwave-assisted synthesis was developed for the tunable fabrication of a novel Cu@IrO 2 core@shell nanowire motif. Experimental parameters, such as (i) reaction time, (ii) the method of addition of the Ir precursor, (iii) capping agent, (iv) reducing agent, as well as (v) the capping agent-to-reducing agent ratio, were subsequently optimized. The viability of other methods based on previously reported literature, such as refluxing, stirring, and physical sonication, was studied and compared with our optimized microwave-assisted protocol in creating our as-prepared materials. It should be noted that the magnitude of the IrO 2 shell could be tailored based on varying the Cu: Ir ratio coupled with judicious variations in the amounts of capping agent and reducing agent. Structural characterization techniques, such as XRD, XPS, and HRTEM (including HRTEM-EDS), were used to analyze our Cu@IrO 2 motifs. Specifically, the shell could be reliably tailored from sizes of 10 nm, 8 nm, 6 nm, and 3.5 nm with corresponding Cu: Ir ratios of 10:1, 15:1, 20:1, and 25:1, respectively. Moreover, the structural integrity of the motifs was probed and found to have been maintained after not only heat treatment but also the post-methane conversion process, indicative of an intrinsically high stability. Both components within the CuO-IrO 2 interface were able to activate methane at temperatures between 400 to 500 K with a reduction of the associated metal cations (Cu 2+ → Cu 1+ ; Ir 4+ → Ir 3+ ) and the deposition of CH x fragments on the surface, as clearly observed in the ambient-pressure XPS results. Thus, on the basis of their stability and chemical activity, these core-shell materials could be very useful for the catalytic conversion of methane into 'higher value" chemicals.

36 MATERIALS SCIENCE↗