Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “W”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

The influence of cobalt, tantalum, and tungsten on the microstructure of single crystal nickel-base superalloys

The influence of composition on the microstructure of single crystal nickel-base superalloys was investigated. Co was replaced by Ni, and Ta was replaced by either Ni or W, according to a matrix of compositions based on MAR-M247. Substitution of Ni for Co caused an increase in gamma-prime solvus temperature, an increase in gamma-gamma-prime lattice mismatch, and the precipitation of W-rich phases in the alloys with high refractory metal levels. Substitution of Ni for Ta caused large decreases in gamma-prime solvus temperature, gamma-prime volume fraction, and gamma-gamma-prime lattice mismatch, whereas substitution of W for Ta resulted in smaller decreases in these features. For the alloys with gamma-prime particles that remained coherent, substitution of Ni for Co caused an increase in gamma-prime coarsening rate. The two alloys with the largest magnitude of lattice mismatch possessed gamma-prime particles which lost coherency during unstressed aging and exhibited anomalously low coarsening rates. Creep exposure at 1000 C resulted in the formation of gamma-prime lamellae oriented perpendicular to the applied stress axis in all alloys.

Nathal, M. V.↗
NASA NTRS1985

The influence of cobalt, tantalum, and tungsten on the elevated temperature mechanical properties of single crystal nickel-base superalloys

The influence of composition on the tensile and creep strength of 001-line oriented nickel-base superalloy single crystals at temperatures near 1000 C was investigated. Cobalt, tantalum, and tungsten concentrations were varied according to a matrix of compositions based on the single crystal version of MAR-M247. For alloys with the baseline refractory metal level of 3 wt pct Ta and 10 wt pct W, decreases in Co level from 10 to 0 wt pct resulted in increased tensile and creep strength. Substitution of 2 wt pct W for 3 wt pct Ta resulted in decreased creep life at high stresses, but improved life at low stresses. Substitution of Ni for Ta caused large reductions in tensile strength and creep resistance, and corresponding increases in ductility. For these alloys with low Ta-plus-W totals, strength was independent of Co level. The effects of composition on properties were related to the microstructural features of the alloys. In general, high creep strength was associated with high levels of gamma-prime volume fraction, gamma-gamma-prime lattice mismatch, and solid solution hardening.

Nathal, M. V.↗
NASA NTRS1986

Formation and characterization of simulated small droplet icing clouds

Two pneumatic two-fluid atomizers operating at high liquid and gas pressures produced water sprays that simulated small droplet clouds for use in studying icing effects on aircraft performance. To measure median volume diameter, MVD or D sub v.5, of small droplet water sprays, a scattered-light scanning instrument was developed. Drop size data agreed fairly well with calculated values at water and nitrogen pressures of 60 and 20 psig, respectively, and at water and nitrogen pressures of 250 and 100 psig, respectively, but not very well at intermediate values of water and nitrogen pressure. MVD data were correlated with D sub O, W sub N, and W sub w, i.e., orifice diameter, nitrogen, and water flowrate, respectively, to give the expression for MVD in microns.

Ingebo, R. D.↗
NASA NTRS1986

The 20 GHz spacecraft IMPATT solid state transmitter

The engineering development of a solid-state transmitter amplifier operating in the 20-GHz frequency range is described. This effort involved a multitude of disciplines including IMPATT device development, circulator design, multiple-diode circuit design, and amplifier integration and test. The objective was to develop a transmitter amplifier demonstrating the feasibility of providing an efficient, reliable, lightweight solid-state transmitter to be flown on a 30 to 20 GHz communication demonstration satellite. The work was done under contract from NASA/Lewis Research Center for a period of three years. The result was the development of a GaAs IMPACT diode amplifier capable of an 11-W CW output power and a 2-dB bandwidth of 300 MHz. GaAs IMPATT diodes incorporating diamond heatsink and double-Read doping profile capable of 5.3-W CW oscillator output power and 15.5% efficiency were developed. Up to 19% efficiency was also observed for an output power level of 4.4 W. High performance circulators with a 0.2 dB inserting loss and bandwidth of 5 GHz have also been developed. These represent a significant advance in both device and power combiner circuit technologies in K-band frequencies.

Best, T.↗
NASA NTRS1987

Deconvolution of spectra for intimate mixtures

Visible to near infrared reflectance spectra of macroscopic mixtures have been shown to be linear combinations of the reflections of the pure mineral components in the mixture. However, for microscopic mixtures the mixing systematics are in general nonlinear. The systematics may be linearized by conversion of reflectance to single scattering albedo (w), where the equations which relate reflectance to w depend on the method of data collection. Several proposed mixing models may be used to estimate mineral abundances from the reflectance spectra of intimate mixtures. These models are summarized and a revised model is presented. A noniterative (linear) least squares approach was used for curve fitting and the data, measured as bi-directional reflectance with incidence and emergence angles of 30 and 0 deg were converted to w by a simplified version of Hapke's equation for bi-directional reflectance. This model was tested with two mixture series composed of 45 to 75 micron particles: an anorthite-enstatite series and an olivine-magnetite series. The data indicate that the simplified Hapke's equation may be used to convolve reflectance spectra into mineral abundances if appropriate endmembers are known or derived from other techniques. For surfaces that contain a significant component of very low albedo material, a somewhat modified version of this technique will need to be developed. Since the abundances are calculated using a noniterative approach, the application of this method is especially efficient for large spectral data sets, such as those produced by mapping spectrometers.

Mustard, John F.↗
NASA NTRS1987

Regenerative fuel cell study for satellites in GEO orbit

Summarized are the results of a 12-month study to identify high performance regenerative hydrogen-oxygen fuel cell concepts for geosynchronous satellite application. Emphasis was placed on concepts with the potential for high energy density (W-hr/lb) and passive means for water and heat management to maximize system reliability. Both polymer membrane and alkaline electrolyte fuel cells were considered, with emphasis on the alkaline cell because of its high performance, advanced state of development, and proven ability to operate in a launch and space environment. Three alkaline system concepts were studied. The first, the integrated design, utilized a configuration in which the fuel cell and electrolysis cells are alternately stacked inside a pressure vessel. Product water is transferred by diffusion during electrolysis and waste heat is conducted through the pressure wall, thus using completely passive means for transfer and control. The second alkaline system, the dedicated design, uses a separate fuel cell and electrolysis stack so that each unit can be optimized in size and weight based on its orbital operating period. The third design was a dual function stack configuration, in which each cell can operate in both fuel cell and electrolysis mode, thus eliminating the need for two separate stacks and associated equipment. Results indicate that using near term technology energy densities between 46 and 52 W-hr/lb can be achieved at efficiencies of 55 percent. System densities of 115 W-hr/lb are contemplated.

Levy, Alexander↗
NASA NTRS1986

A 20 GHz, high efficiency dual mode TWT for the ACTS program

The development of a 50 W/10 W dual mode K-band downlink TWT is examined, and its performance is evaluated. The designs of the electron gun, RF circuit, and collector for the TWT, which is enclosed in a capsule, are described. It is observed that the high power mode (HPM) power output is at 50 GHz and the low power mode (LPM) output is at 12 GHz; the saturated gain is 52.5 dB for HPM and 3 dB for LPM; the AM-PM is 4.2 dB; the HPM dc power output is 104 W; and the LPM dc output is 42 W; and the efficiency is 45 percent for the HPM and 28.6 percent for the LPM.

Muennemann, Frank↗
NASA NTRS1987

Solar wind diagnostics from Doppler-enhanced scattering

Solar wind ions can attain sufficient outflow speed, w, to cause line excitation by chromospheric or transition region radiation in a nearby line. It is shown that this extends the diagnostic possibilities of a coronal EUV line to much larger values of w than would be possible if pumping were limited to radiation from the same spectral line. For the 1037.6 A coronal line of O VI, the pumping effect of the chromospheric C II 1037.0 A line is efficient for w between 100 and 250 km/s. An approximate expression for the line ratio for a doublet of the Li or Na isoelectronic sequences is derived, and the diagnostic capabilities of doublet line ratios, either by themselves or combined with the observation of other quantities, are discussed. In particular, that the determination of doublet line ratios at several heights can be sufficient to yield the solar wind velocity at those heights together with a constraint on other coronal parameters.

Noci, Giancarlo↗
NASA NTRS1987

Retrieval of total precipitable water using radiometric measurements near 183.3 GHz and 90 GHz frequencies

Data collected with the Advanced Microwave Moisture Sounder (AMMS), which operates in the 183.3 GHz range, are compared to measurements collected at 22 GHz in order to show that the 183 GHz measurements are more sensitive to total precipitable water (W) values than the 22 GHz measurements. Radiative transfer calculations for the upwelling microwave emission from the ocean surface were performed at the AMMS frequencies with a variety of atmospheric temperature and humidity profiles. The derived brightness temperatures at these frequencies are compared with W values derived from the humidity profiles. It is observed that the sensitivity between the brightness temperatures and W values at the AMMS channel is greater than 130 K/g per sq cm and 12 K/g per sq cm for the 22 GHz frequency.

Wang, J. R.↗
NASA NTRS1988

Friction and Wear of Monolithic and Fiber Reinforced Silicon-Ceramics Sliding Against IN-718 Alloy at 25 to 800 C in Atmospheric Air at Ambient Pressure

The friction and wear of monolithic and fiber reinforced Si-ceramics sliding against the nickel base alloy IN-718 at 25 to 800 C was measured. The monolithic materials tested were silicon carbide (SiC), fused silica (SiO2), syalon, silicon nitride (Si3N4) with W and Mg additives, and Si3N4 with Y2O3 additive. At 25 C fused silica had the lowest friction while Si3N4 (W,Mg type) had the lowest wear. At 800 C syalon had the lowest friction while Si3N4 (W,Mg type) and syalon had the lowest wear. The SiC/IN-718 couple had the lowest total wear at 25 C. At 800 C the fused silica/IN-718 couple exhibited the least total wear. SiC fiber reinforced reaction bonded silicon nitride (RBSN) composite material with a porosity of 32 percent and a fiber content of 23 vol percent had a lower coefficient of friction and wear when sliding parallel to the fiber direction than in the perpendicular at 25 C. The coefficient of friction for the carbon fiber reinforced borosilicate composite was 0.18 at 25 C. This is the lowest of all the couples tested. Wear of this material was about two decades smaller than that of the monolithic fused silica. This illustrates the large improvement in tribological properties which can be achieved in ceramic materials by fiber reinforcement. At higher temperatures the oxidation products formed on the IN-718 alloy are transferred to the ceramic by sliding action and forms a thin, solid lubricant layer which decreases friction and wear for both the monolithic and fiber reinforced composites.

Deadmore, Daniel L.↗
NASA NTRS1988

A method to dramatically improve subcarrier tracking

A method is presented for achieving a dramatic improvement in phase tracking of square wave subcarriers or other square waves. The method is to set the amplitude of the phase quadrature reference signal to zero except near the zero crossings of the input signal. Without changing the loop bandwidth, the variance of the phase error can be reduced to approximately W sigma(sub 0)(2), where sigma (sub 0)(2) is the phase error variance without windowing, and W is the fraction of cycle in which the reference signal has a nonzero value. Simulation results confirm the analysis and establish minimum W versus signal-to-noise ratio. Typically, the window can be made so narrow as to achieve a phase error variance of 1.5 sigma(sub 0)(4).

Hurd, William J.↗
NASA NTRS1988

Tensile behavior of tungsten and tungsten-alloy wires from 1300 to 1600 K

The tensile behavior of a 200-micrometer-diameter tungsten lamp (218CS-W), tungsten + 1.0 atomic percent (a/o) thoria (ST300-W), and tungsten + 0.4 a/o hafnium carbide (WHfC) wires was determined over the temperature range 1300 t0 1600 K at strain rates of 3.3 X 10 to the -2 to 3.3 X 10 to the -5/sec. Although most tests were conducted on as-drawn materials, one series of tests was undertaken on ST300-W wires in four different conditions: as-drawn and vacuum-annealed at 1535 K for 1 hr, with and without electroplating. Whereas heat treatment had no effect on tensile properties, electropolishing significantly increased both the proportional limit and ductility, but not the ultimate tensile strength. Comparison of the behavior of the three alloys indicates that the HfC-dispersed material possesses superior tensile properties. Theoretical calculations indicate that the strength/ductility advantage of WHfC is due to the resistance to recrystallization imparted by the dispersoid.

Hee, Man Yun↗
NASA NTRS1989

Gas-phase flowrate effect on disintegrating cryogenic liquid-jets

Two phase liquid and gaseous nitrogen flow in a pneumatic two fluid atomizer was investigated. Characteristic dropsize for cryogenic sprays were measured with a scattered light scanning instrument developed at NASA-Lewis. Tests were conducted primarily in the aerodynamic stripping regime of liquid jet atomization. At a sampling distance of bar-x=1.3 cm, the Sauter mean, D(sub 32), and volume median, D(sub v.5), drop diameters were measured and correlated with nitrogen gas flowrate, W(sub n), to give the following expressions: D sub 32 to the -1=210W(sub n) to the -1.33 and D(sub v.5) to the -1=150 W(sub n to the -1.33, where reciprocal diameters and gas flowrate are in cm (-1) and g/sec, respectively. The exponent 1.33 for nitrogrn gas flowrate, W(sub n), is the same as that predicted by atomization theory for liquid-jet breakup in high velocity gasflow. When the spray was sampled at axial distances of bar-x=2.5 and 4.5 cm downstream of the atomizer, the exponent decreased to 1.2 and 0.9, respectively. This was attributed to the loss of small droplets due to their rapid vaporization.

Ingebo, Robert D.↗
NASA NTRS1989

Processing and microstructure of melt spun NiAl alloys

The influence of various melt spinning parameters and the effect of consolidation on the microstructure of melt spun NiAl and NiAl + W alloys have been examined by optical and electron microscopy techniques. It was found that the addition of 0.5 at. pct W to NiAl results in a fine dispersion of W particles after melt spinning which effectively controls grain growth during annealing treatments or consolidation at temperatures between 1523 and 1723 K. Increased wheel speeds are effective at reducing both the ribbon thickness and grain size, such that proper choice of both composition and casting parameters can produce structures with grain sizes as small as 2 microns. Finally, fabrication of continuous fiber-reinforced composites which used pulverized ribbon as the matrix material was demonstrated.

Locci, I. E.↗
NASA NTRS1990

Validation of the geostrophic method for estimating zonal currents at the equator from Geosat altimeter data

The applicability of satellite altimeter data for estimating zonal current variability at the equator is assessed using the meriodionally differenced form of the geostrophic balance. Estimates of geostrophic zonal flow anomalies in the equatorial Pacific have been deduced from 17-day collinear altimeter data during the first year of the Geosat Exact Repeat Mission. Altimeter-derived geostrophic estimates agree well with in situ zonal current variability. Comparison of flow-frequency near-surface zonal current observed from equatorial moorings at 165 deg E, 140 deg W, and 110 deg W yield correlations of 0.83, 0.85, and 0.51, respectively, with a mean rms difference of 23 cm/sec. The inclusion of up to 11 ascending and descending Geosat tracks within the 9-deg band for every 17-day repeat effectively reduced the temporal sampling interval to 1.5 days at 165 deg E and 140 deg W. The 6.8-km along track spacing of the altimeter measurements provides sufficient resolution for the effective filtering of small-scale meridional noise, both instrumental and oceanic.

Picaut, Joel↗
NASA NTRS1990

Recycled grains in lunar soils as an additional, necessary, regolith evolution parameter

Recycled lunar soil grains are defined as those soil grains that have been a part of either regolith breccias or agglutinates; thus, mineral grains, rock fragments, older agglutinates, and volcanic glass spherules, if dislodged from an agglutinate or a regolith breccia, would all qualify as recycled grains. This paper shows that it is possible to estimate the proportion of recycled material in lunar soils. Optical data from 12 soils in the Apollo 16 core 64001/2 were collected to estimate the proportion (W) of recycled crystalline grains in each of these soils. The W values show a correspondence with other independently derived parameters and the history of the core soils, indicating that W can be used as a valid soil-evolution parameter.

Basu, A.↗
NASA NTRS1989

Requirements and designs for Mars Rover RTGs

A typical Rover mission, its requirements, the environment it imposes on the radionuclide thermoelectric generator (RTG), and a design approach for making the RTG operable in such an environment are described. Specific RTG designs for various thermoelectric element alternatives are presented. The results of studies show that current multifoil-insulated GPHS (general-purpose heat source) RTG and Mod-RTG designs can be modified to operate in an environment with an external atmosphere (e.g., Mars). This can be done while the helium generated by the fuel's alpha decay is vented to the external atmosphere. The use of novel selective vents and high-capacity getters is not required. The Rover RTGs can be built from standard, proven GPHS modules and standard SiGe unicouples or SiGe/GaP multicouples, using demonstrated thermoelectric material performance parameters. Rover's 500-W power requirement can be satisfied with two 250-W or four 125-W RTGs, whose sizes are compatible with currently envisaged Rover designs. An auxiliary cooling loop (e.g., water and antifreeze) will be required to cool the RTG while it is within the Rover's aeroshell during launch and transit to Mars.

Schock, A.↗
NASA NTRS1990

Mass-losing M supergiants in the solar neighborhood

A list of the 21 mass-losing red supergiants (20 M type, one G type; L greater than 100,000 solar luminosities) within 2.5 kpc of the sun is compiled. These supergiants are highly evolved descendants of main-sequence stars with initial masses larger than 20 solar masses. The surface density is between about 1 and 2/sq kpc. As found previously, these stars are much less concentrated toward the Galactic center than W-R stars, which are also highly evolved massive stars. Although with considerable uncertainty, it is estimated that the mass return by the M supergiants is somewhere between 0.00001 and 0.00003 solar mass/sq kpc yr. In the hemisphere facing the Galactic center there is much less mass loss from M supergiants than from W-R stars, but, in the anticenter direction, the M supergiants return more mass than do the W-R stars. The duration of the M supergiant phase appears to be between 200,000 and 400,000 yr. During this phase, a star of initially at least 20 solar masses returns perhaps 3-10 solar masses into the interstellar medium.

Jura, M.↗