Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Vortex flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

An experimental investigation of S-duct flow control using arrays of low-profile vortex generators

An experimental investigation was undertaken to measure the effect of various configurations of low-profile vortex generator arrays on the flow in a diffusing S-duct. Three parameters that characterize the vortex generator array were systematically varied to determine their effect: (1) the vortex generator height; (2) the streamwise location of the vortex generator array; and (3) the vortex generator spacing. Detailed measurements of total pressure at the duct exit, surface static pressure, and surface flow visualization were gathered for each vortex generator configuration. These results are reported here along with total pressure recovery and distortion coefficients determined from the experimental data. Each array of vortex generators tested improved total pressure recovery. The configuration employing the largest vortex generators was the most effective in reducing total pressure recovery. No configuration of vortex generators completely eliminated the flow separation that naturally occurs in the S-duct, however the extent of the separated flow region was reduced.

Reichert, Bruce A.↗
NASA NTRS1987

Evaluation of Navier-Stokes and Euler solutions for leading-edge separation vortices

Extensive study on the numerical simulation of the vortical flow over a double delta wing is carried out using the thin layer Navier-Stokes and Euler equations. Two important flow characteristics, vortex interaction and vortex breakdown, are successfully simulated. Grid resolution is one of the most important factors associated with the vortex problem. Computations were performed on a series of grids with various levels of refinement, coarse, medium, and fine. Computations using either the coarse or medium grids fail to capture the proper physical phenomena. The computed result using a fine grid shows flow unsteadiness once the vortex breakdown takes place. The C sub L - alpha characteristics are well predicted up to the breakdown angle of attack for all the grid distributions. The Euler solutions show fairly good agreement with the experiment on the C sub L - alpha characteristics. However, other aspects of the solution at each angle of attack, such as the locus of the leading edge separation vortex, are not consistent with the experiment. Even for the fine grid Navier-Stokes computations, further grid resolution is required to obtain good quantitative agreement with the experiment.

Fujii, K.↗
NASA NTRS1987

Evaluation of Navier-Stokes and Euler solutions for leading-edge separation vortices

Extensive study on the numerical simulation of the vortical flow over a double delta wing is carried out using the thin layer Navier-Stokes and Euler equations. Two important flow characteristics, vortex interaction and vortex breakdown, are successfully simulated. Grid resolution is one of the most important factors associated with the vortex problem. Computations were performed on a series of grids with various levels of refinement, coarse, medium, and fine. Computations using either the coarse or medium grids fail to capture the proper physical phenomena. The computed result using a fine grid shows flow unsteadiness once the vortex breakdown takes place. The C sub L - alpha characteristics are well predicted up to the breakdown angle of attack for all the grid distributions. The Euler solutions show fairly good agreement with the experiment on the C sub L - alpha characteristics. However, other aspects of the solution at each angle of attack, such as the locus of the leading edge separation vortex, are not consistent with the experiment. Even for the fine grid Navier-Stokes computations, further grid resolution is required to obtain good quantitative agreement with the experiment.

Fujii, K.↗
NASA NTRS1990

Numerical investigation of the origin of vortex asymmetry

The flow about a slender body of revolution placed at incidence to an oncoming stream is numerically investigated for angles of attack ranging from 20 to 80 degrees and a Reynolds number of 200,000, based on freestream conditions and maximum body diameter. Navier-Stokes computations are applied to investigate the phenomena governing the onset of vortex asymmetry. Time-accurate solutions are given for an ogive-cylinder body with and without a space-fixed time-invariant disturbance added near the tip. At a 40-degree angle of attack the flow is found to be steady but becomes highly asymmetric when the disturbance is added. The level of asymmetry is dependent upon the size and location of the disturbance. It is suggested that the origin of the asymmetry is a convective-type instability of the originally symmetric flow. For higher angles of attack (60 and 80 degrees) the flow around the cylindrical part becomes unsteady, and vortex shedding is observed. It is suggested that the origin of flow unsteadiness and vortex shedding in the wake is an absolute-type instability of the originally steady flow.

Degani, David↗
NASA NTRS1990

Investigation of transonic flow over segmented slotted wind tunnel wall with mass transfer

The flowfield on a segmented multi-slotted wind tunnel wall was studied at transonic speeds by measurements in and near the wall layer using five port cone probes. The slotted wall flowfield was observed to be three-dimensional in nature for a relatively significant distance above the slot. The boundary layer characteristics measured on the single slotted wall were found to be very sensitive to the applied suction through the slot. The perturbation in the velocity components generated due to the flow through the slot decay rapidly in the transverse direction. A vortex-like flow existed on the single slotted wall for natural ventilation but diminished with increased suction flow rate. For flow on a segmented multi-slotted wall, the normal velocity component changes were found to be maximum for measurement points located between the segmented slots atop the active chamber. The lateral influence due to applied suction and blowing, through a compartment, exceeded only slightly that in the downstream direction. Limited upstream influence was observed. Influence coefficients were determined from the data in the least-square sense for blowing and suction applied through one and two compartments. This was found to be an adequate determination of the influence coefficients for the range of mass flows considered.

Bhat, M. K.↗
NASA NTRS1993

An experimental investigation of S-duct flow control using arrays of low-profile vortex generators

An experimental investigation was undertaken to measure the effect of various configurations of low-profile vortex generator arrays on the flow in a diffusing S-duct. Three parameters that characterize the vortex generator array were systematically varied to determine their effect: (1) the vortex generator height, (2) the streamwise location of the vortex generator array, and (3) the vortex generator spacing. Each array of vortex generators tested improved total pressure recovery. The configuration employing the largest vortex generators was the most effective in reducing total pressure distortion but did not produce the greatest total pressure recovery. No configuration of vortex generators completely eliminated the flow separation that naturally occurs in the S-duct; however the extent of the separated flow region was reduced.

Reichert, B. A.↗
NASA NTRS1983

Experimental investigation of forebody and wing leading-edge vortex interactions at high angles of attack

An experimental investigation was conducted to assess the vortex flow-field interactions on an advanced, twin-jet fighter aircraft configuration at high angles of attack. Flow-field surveys were conducted on a small-scale model in the Northrop 0.41 - by 0.60-meter water tunnel and, where appropriate, the qualitative observations were correlated with low-speed wind tunnel data trends obtained on a large-scale model of the advanced fighter in the NASA Langley Research Center 30- by 60-foot (9.1- by 18.3-meter) facility. Emphasis was placed on understanding the interactions of the forebody and LEX-wing vortical flows, defining the effects on rolling moment variation with sideslip, and identifying modifications to control or regulate the vortex interactions at high angles of attack. The water tunnel flow visualization results and wind tunnel data trend analysis revealed the potential for strong interactions between the forebody and LEX vortices at high angles of attack. In particular, the forebody flow development near the nose could be controlled by means of carefully-positioned radome strakes. The resultant strake-induced flow-field changes were amplified downstream by the more powerful LEX vortical motions with subsequent large effects on wing flow separation characteristics.

Erickson, G. E.↗
NASA NTRS1981

A discrete vortex method for the non-steady separated flow over an airfoil

A discrete vortex method was used to analyze the separated non-steady flow about a cambered airfoil. The foil flow modelling is based on the thin lifting-surface approach, where the chordwise location of the separation point is assumed to be known from experiments or flow-visualization data. Calculated results provided good agreement when compared with the post-stall aerodynamic data of two airfoils. Those airfoil sections differed in the extent of travel of the separation point with increasing angle of attack. Furthermore, the periodic wake shedding was analyzed and its time-dependent influence on the airfoil was investigated.

Katz, J.↗
NASA NTRS1984

Investigations of flow field perturbations induced on slotted transonic-tunnel walls

The free-stream interference caused by the flow through the slotted walls of the test sections of transonic wind tunnels has continuously a problem in transonic tunnel testing. The adaptive-wall transonic tunnel is designed to actively control the near-wall boundary conditions by sucking or blowing through the wall. In order to make the adaptive-wall concept work, parameters for computational boundary conditions must be known. These parameters must be measured with sufficient accuracy to allow numerical convergence of the flow field computations and must be measured in an inviscid region away from the model that is placed inside the wind tunnel. The near-wall flow field was mapped in detail using a five-port cone probe that was traversed in a plane transverse to the free-stream flow. The initial experiments were made using a single slot and recent measurements used multiple slots, all with the tunnel empty. The projection of the flow field velocity vectors on the transverse plane revealed the presence of a vortex-like flow with vorticity in the free stream. The current research involves the measurement of the flow field above a multislotted system with segmented plenums behind it, in which the flow is controlled through several plenums simultaneously. This system would be used to control a three-dimensional flow field.

Wu, J. M.↗
NASA NTRS1984

Euler and Navier-Stokes solutions for supersonic shear flow past a circular cylinder

Euler and Navier-Stokes solutions of the supersonic shear flow past a circular cylinder are obtained. These solutions are used to study the basic flow structure around the cylinder. Both the inviscid and viscous calculations show the formation of a large recirculating flow region around the front stagnation point. The calculations further show that the overall size of the recirculating region is approximately the same for the Euler and Navier-Stokes solutions but the inside structure is quite different. The inviscid flow shows only one vortex whereas the viscous flow shows two vortices inside the recirculating flow region. The inner vortex in the Navier-Stokes solution is formed primarily due to the viscous effects near the body surface and its size depends upon the Reynolds number. It is found that with increasing Reynolds number, the inner vortex diminishes in size and the Navier-Stokes solution asymptotically approaches the Euler solution. These results indicate that the Euler equations may correctly predict certain high Reynolds number separation phenomenon in flows with natural inviscid vorticity source.

Kumar, A.↗
NASA NTRS1974

Theoretical and experimental longitudinal aerodynamic characteristics of an aspect ratio 0.25 sharp-edge delta wing at subsonic, supersonic, and hypersonic speeds

The suction analogy concept of Polhamus for predicting vortex lift in conjunction with an appropriate potential-flow solution is called the present method. This method is applied to an aspect ratio 0.25 sharp-edge delta wing from a Mach number of 0.143 to 10.4 in free air and at 0.074 in ground effect, and also to an aspect ratio 0.35 triangular crosssectional body at a Mach number of 6.9. The models had subsonic leading edges at the test Mach numbers. Vortex-flow effects could be neither confirmed nor denied to exist at high speeds because of the lack of flow visualization above a Mach number of 0.143. The data, however, could be better predicted by including a vortex-flow effect, although not always to the extent predicted from the present method because of the presence of actual and hypothesized unmodeled flow situations. The method of Nenni and Tung (NASA CR-1860) tended to confirm the existence of vortex flow at hypersonic speeds. The hypersonic-tangent-cone method predicted best the delta-wing results over the test angle-of-attack range and hypersonic Mach number range and did equally as well as the present method for the triangular body.

Fox, C. H., Jr.↗
NASA NTRS1975

A three-dimensional solution of flows over wings with leading-edge vortex separation

The application of a new, general, potential flow computational technique to the solution of the subsonic, three-dimensional flow over wings with leading-edge vortex separation is presented. The present method is capable of predicting forces, moments, and detailed surface pressures on thin, sharp-edged wings of rather arbitrary planform. The wing geometry is arbitrary in the sense that leading and trailing edges may be curved or kinked and the wing may have arbitrary camber and twist. The method employs an inviscid flow model in which the wing, the rolled-up vortex sheets, and the wake are represented by piecewise continuous quadratic doublet sheet distributions. The Kutta condition is imposed along all wing edges. Strengths of the doublet distributions as well as shape and position of the free fortex sheet spirals are computed in iterative fashion starting with an assumed initial sheet geometry. The method is verified by numerous computed results.

Weber, J. A.↗
NASA NTRS1981

Rapid, high-order accurate calculation of flows due to free source or vortex distributions

Fast Fourier transform (FFT) techniques are applied to the problem of finding the flow due to source or vortex distributions in the field outside an airfoil or other two-dimensional body. Either the complex potential or the complex velocity may be obtained to a high order of accuracy, with computational effort similar to that required by second-order fast Poisson solvers. These techniques are applicable to general flow problems with compressibility and rotation. An example is given of their use for inviscid compressible flow.

Halsey, D.↗
NASA NTRS1992

Flame deformation and entrainment associated with an isothermal transverse fuel jet

This paper describes an analytical model of an incompressible, isothermal reacting jet in crossflow. The model represents the flow in the jet cross-section by a counter rotating vortex pair, a flow structure that has been observed to dominate the jet behavior. The reaction surface surrounding the fuel jet is represented as a composite of strained diffusion flames that are stretched and deformed by the vortex pair flow. The results shed new light on the interaction between the vortex pair circulation and flame structure evolution and their relation to the concept of entrainment.

Jenkins, D. W.↗
NASA NTRS1996

Aerostructural Vortical Flow Interactions with Applications to F/A-18 and F-117 Tail Buffet

The buffet response of the flexible twin-tail configuration of the F/A-18 and a generic F-111 aircraft are computationally simulated and experimentally validated. The problem is a multidisciplinary one which requires the sequential solution of three sets of equations on a multi-block grid structure. The first set is the unsteady, compressible, full Navier-Stokes equations. The second set is the aeroelastic equations for bending and torsional twin-tail responses. The third set is the grid-displacement equations which are used to update the grid coordinates due to the tail deflections. The computational models consist of a 76 deg. swept back, sharp edged delta wing of aspect ratio of one and a swept-back F/A-18 or F-117 twin-tail. The configuration is pitched at 30 deg. angle-of-attack. The problem is solved for the initial flow conditions with the twin tails kept rigid. Next, the aeroelastic equations of the tails are turned on along with the grid-displacement equations to solve for the bending and torsional tails responses due to the unsteady loads produced by the vortex breakdown flow of the leading-edge vortex cores of the delta wing. Several spanwise locations of the twin tails are investigated. The computational results are validated using several existing experimental data.

Kandil, Osama A.↗