Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transient Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Thermodynamic Analysis of Thermo-vacuum Clothes Drying Operation

Clothes drying accounts for a significant amount of energy consumed in residential and commercial sectors. A thermal vacuum clothes drying technology (TVCD) is proposed as an advanced clothes dryer which can significantly reduce the energy requirements by expediting the drying process. In the conventional convective clothes dryer, hot dry air is introduced into the drum which gets in direct contact to dry the clothes. This process is energy inefficient since the significant amount of heat and the water carried out with the exhaust stream are wasted. In contrast to the conventional convective drying technique, the drying mechanism of TVCD is through nucleate boiling at low temperature due to reduced vessel pressure. The process is not only efficient but also reduces the required time for drying. The objective of this paper is to develop a comprehensive thermodynamic model to predict the transient drying process of TVCD. The three-stage system model including the detail analysis of individual components is capable of simulating the variation of the water content in the textile under various operational conditions. The preliminary results show that the drying time of 3 lb textile from 70% to 2.5% in TVCD is approximately four times less than the time required in the conventional clothes dryer. Parametric studies are carried out to understand the effect of operation conditions and component geometry on the system performance. Energy consumption of the system is also analyzed.

Yang, Cheng-Min↗
DOE OSTI2021

Utilizing Environmental Tracers to Reduce Groundwater Flow and Transport Model Parameter Uncertainties

Abstract Non‐uniqueness in groundwater model calibration is a primary source of uncertainty in groundwater flow and transport predictions. In this study, we investigate the ability of environmental tracer information to constrain groundwater model parameters. We utilize a pilot point calibration procedure conditioned to subsets of observed data including: liquid pressures, tritium ( 3 H), chlorofluorocarbon‐12 (CFC‐12), and sulfur hexafluoride (SF 6 ) concentrations; and groundwater apparent ages inferred from these environmental tracers, to quantify uncertainties in the heterogeneous permeability fields and infiltration rates of a steady‐state 2‐D synthetic aquifer and a transient 3‐D model of a field site located near Riverton, Wyoming (USA). To identify the relative data worth of each observation data type, the post‐calibration uncertainties of the optimal parameters for a given observation subset are compared to that from the full observation data set. Our results suggest that the calibration‐constrained permeability field uncertainties are largest when liquid pressures are used as the sole calibration data set. We find significant reduction in permeability uncertainty and increased predictive accuracy when the environmental tracer concentrations, rather than apparent groundwater ages, are used as calibration targets in the synthetic model. Calibration of the Riverton field site model using environmental tracer concentrations directly produces infiltration rate estimates with the lowest uncertainties, however; permeability field uncertainties remain similar between the environmental tracer concentration and apparent groundwater age calibration scenarios. This work provides insight on the data worth of environmental tracer information to calibrate groundwater models and highlights potential benefits of directly assimilating environmental tracer concentrations into model parameter estimation procedures.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

PV and Dynamic Load Modeling Update

This report documents the PV and dynamic load modeling update for transient stability, EMT, harmonics, and short circuit analyses during budget period one of the DOE PV-MOD research.

14 SOLAR ENERGY↗
DOE OSTI2021

Transient quasi-periodic oscillations at γ-rays in the TeV blazar PKS 1510-089

ABSTRACT We present periodicity search analyses on the γ-ray light curve of the TeV blazar PKS 1510-089 observed by the Fermi Large Area Telescope. We report the detection of two transient quasi-periodic oscillations: A 3.6-d QPO during the outburst in 2009 that lasted five cycles (MJD 54906–54923); and a periodicity of 92 d spanning over 650 d from 2018 to 2020 (MJD 58200–58850), which lasted for seven cycles. We employed the Lomb–Scargle periodogram, Weighted Wavelet Z-transform, redfit, and the Monte Carlo light-curve simulation techniques to find any periodicity and the corresponding significance. The 3.6-d QPO was detected at a moderate significance of ∼3.5σ, while the detection significance of the 92-d QPO was ∼7.0σ. We explore a few physical models for such transient QPOs including a binary black hole system, precession of the jet, a non-axisymmetric instability rotating around the central black hole near the innermost stable circular orbit, the presence of quasi-equidistant magnetic islands inside the jet, and a geometric model involving a plasma blob moving helically inside a curved jet.

Roy, Abhradeep (ORCID:0000000249984560)↗
NASA NTRS1981

Lunar volcanic glasses and their constraints on mare petrogenesis

The compositional properties of volcanic glasses from the Apollo 11, 14, 15 and 16 landing sites are examined and implications of the results for mare basalt petrogenesis and deep lunar structures are discussed. Major-element and nickel analyses were performed on the glasses using electron probe techniques, and R-mode principal component analysis was performed on the 19 different compositions of glass distinguished. The glasses are found to form two distinct chemical arrays based on the major elements and Ni. The presence of two chemically isolated cumulate systems in the mantle at different depths is thus inferred, and a model is developed for mare petrogenesis in which each system was itself composed of two lithologic components that underwent hybridization, assimilation or mixing to generate the large compositional range of magmas represented by the lunar volcanic glasses. The surface-correlated elements associated with the volcanic glasses are attributed to another reservoir in the deep interior which may be responsible for gas emissions causing lunar transient phenomena. The model developed allows predictions to be made concerning the liquidus phase relations, trace and radiogenic element distributions, nonradiogenic isotope compositions and sample ages.

Delano, J. W.↗
NASA NTRS1976

Coupled base motion response analysis of payload structural systems

Coupled base motion response analysis of payload structural systems is discussed. A systems analysis program is described which by component analysis structural transient response analyses can be completed. The program presents a proven technique, used initially on the Skylab program, which is designed to reduce cost and schedule time on detail structural analyses of structural payload systems. Base motion procedures are employed where critical segments of complex structural systems or components may be analyzed for various load conditions without having to re-establish the entire structural system coupled model properties. The transient response characteristics of a complex structural system are used as a basis for evaluating the transient response of a similar system.

Devers, A. D.↗
DOE OSTI2020

Progressive collapse analysis of stiffened panel structure with consideration of actual welding distortion and residual stresses

To date, inclusion of welding distortion and residual stresses in determining the strength of marine structures is based on empirical formulations due to welding complexity. In this study, a more feasible numerical model was developed from the perspective of inherent strain theory. The accuracy of this simplified numerical model was confirmed by transient thermo-elastic–plastic finite element analysis using a novel dynamic mesh refining and iterative substructure method which is 50 times faster than conventional finite element method. Welding distortion by the two numerical approaches was validated with experimental measurement. The collapse analyses indicated that the inherent strain model predicted a compressive strength and load-displacement curve with high accuracy, as validated by the transient thermo-mechanical model. The global stiffness and the ultimate strength of the welded structure would be overestimated by about 22% if no welding effects were considered. The proposed computation procedure for determining the ultimate strength of welded structures is accurate, simple, and practical and enables improvement of ultimate strength through optimization of welding joint design to reduce the welding residual stress and distortion.

Huang, Hui↗
NASA NTRS2018

Numerical Simulation of AFP Nip Point Temperature Prediction for Complex Geometries

Material placement at the ideal nip point temperature over complex surfaces with uniformity across the width of the compaction rollers results in optimized part properties for Automated Fiber Placement (AFP) processes. However, current AFP systems utilize heat control models and methodologies, based on multiple process parameters such as feed-rate and orientation, that are mostly open-loop. Here, infrared (IR) heater input is calibrated as a function of process parameters during machine qualification. This work presents a numerical simulation to predict arrayed-infrared (AIR) emitter radiation onto a substrate that includes view factor implementation, IR radiative heat flow calculation, energy rate balance, and a transient heat transfer model. The purpose of this numerical model is to predict nip point temperature on complex surfaces, serving as a baseline for a new arrayed-infrared (AIR) thermoset heater to improve AFP process control. It is anticipated that this simulation will accurately control the temperature for high-speed AFP layup of complex geometries. An anticipated result of an AIR heater system is that material calibration and testing will be reduced as temperature is instantaneously monitored and controlled. Therefore, temperature across the roller width will be uniform during placement of complex parts, independent of their geometry.

Xia, Kaishu↗
DOE OSTI2020

Residual Stress Modeling with Phase Transformation for Wire Arc Additive Manufacturing of B91 Steel

Wire arc additive manufacturing (WAAM) is an energy-efficient manufacturing technique used for near-net-shape production of functional industrial components. However, heat accumulation during deposition and the associated mechanical and metallurgical changes result in complex residual stress profiles across the cross section of the fabricated components. These residual stresses are detrimental to the service life of the components. In this study, sequentially coupled thermomechanical analysis of WAAM B91 steel is conducted to quantify the residual stress variation across the component. The thermomechanical analysis includes a transient heat transfer model and a static stress model that incorporates the transformation-induced plasticity due to martensitic phase transformation. Here, the experimentally calibrated heat transfer model mirrors the temperature variation of the system during the deposition. The results from the stress model are validated via x-ray diffraction measurements, and the numerical results are in good agreement with the experimental data.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2020

Plant Physiology Increases the Magnitude and Spread of the Transient Climate Response to CO 2 in CMIP6 Earth System Models

Increasing concentrations of CO 2 in the atmosphere influence climate both through CO 2 ’s role as a greenhouse gas and through its impact on plants. Plants respond to atmospheric CO 2 concentrations in several ways that can alter surface energy and water fluxes and thus surface climate, including changes in stomatal conductance, water use, and canopy leaf area. These plant physiological responses are already embedded in most Earth system models, and a robust literature demonstrates that they can affect global-scale temperature. However, the physiological contribution to transient warming has yet to be assessed systematically in Earth system models. Here this gap is addressed using carbon cycle simulations from phases 5 and 6 of the Coupled Model Intercomparison Project (CMIP) to isolate the radiative and physiological contributions to the transient climate response (TCR), which is defined as the change in globally averaged near-surface air temperature during the 20-yr window centered on the time of CO 2 doubling relative to preindustrial CO 2 concentrations. In CMIP6 models, the physiological effect contributes 0.12°C ( σ : 0.09°C; range: 0.02°–0.29°C) of warming to the TCR, corresponding to 6.1% of the full TCR ( σ : 3.8%; range: 1.4%–13.9%). Moreover, variation in the physiological contribution to the TCR across models contributes disproportionately more to the intermodel spread of TCR estimates than it does to the mean. The largest contribution of plant physiology to CO 2 -forced warming—and the intermodel spread in warming—occurs over land, especially in forested regions.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1974

The role of thermal contact resistance in pyrotechnic ignition

This paper describes a pyrotechnic ignition model based on transient heat conduction from a heated bridgewire to a pyrotechnic that is placed in contact with it. The boundary condition used at the interface was a thermal contact conductance estimated at 31,200 W per sq m-K between the wire and the pyrotechnic. Ignition was assumed to occur when a 2.5-micron layer of pyrotechnic next to the bridgewire reached a critical ignition temperature. The times to ignition predicted by this model for constant current firings were in good agreement with experimentally observed times to fire at 3.5- and 5-ampere current levels and ambient temperatures from 144 K to 366 K.

Sernas, V.↗
DOE OSTI2022

A new dynamic zOnal model with air-diffuser (DOMA) - Application to thermal comfort prediction

A new Dynamic zOnal Model with Air-diffuser (DOMA) was developed. Several case studies were investigated and tested to evaluate and validate this program using measurement data. This new model was integrated into a TRaNsient SYstems Simulation program library and coupled with the multi-zone thermal model. The DOMA/TRNSYS coupled model was then used to predict room temperature distribution over an entire day of a single-zone building. The results show that increasing the heating outputs of the electric floor system, for example, from 75 to 200 W/m 2 , would not effectively improve the indoor thermal comfort, since the thermostat will reach the set point first and then turn off the system before the room gets enough heat and reach a comfortable level. This indicates the importance of selecting an appropriate location and set point for the thermostat when using a floor heating system. This potential thermal comfort issue can only be identified through the two-node model with a dynamic zonal model rather than the conventional PMV model, which thus suggests that for optimizing indoor thermal comfort of a building equipped with a time-sensitive control strategy and/or HVAC system, the TSENS results obtained from the two-node model integrated with DOMA are more appropriate than PMVs.

Construction & Building Technology↗
NASA NTRS2016

Tool for the Integrated Dynamic Numerical Propulsion System Simulation (NPSS)/Turbine Engine Closed-Loop Transient Analysis (TTECTrA) User's Guide

The Tool for Turbine Engine Closed-Loop Transient Analysis (TTECTrA ver2) is a control design tool thatenables preliminary estimation of transient performance for models without requiring a full nonlinear controller to bedesigned. The program is compatible with subsonic engine models implemented in the MATLAB/Simulink (TheMathworks, Inc.) environment and Numerical Propulsion System Simulation (NPSS) framework. At a specified flightcondition, TTECTrA will design a closed-loop controller meeting user-defined requirements in a semi or fully automatedfashion. Multiple specifications may be provided, in which case TTECTrA will design one controller for each, producing acollection of controllers in a single run. Each resulting controller contains a setpoint map, a schedule of setpointcontroller gains, and limiters; all contributing to transient characteristics. The goal of the program is to providesteady-state engine designers with more immediate feedback on the transient engine performance earlier in the design cycle.

Transient↗
NASA NTRS2009

Estimation of Faults in DC Electrical Power System

This paper demonstrates a novel optimization-based approach to estimating fault states in a DC power system. Potential faults changing the circuit topology are included along with faulty measurements. Our approach can be considered as a relaxation of the mixed estimation problem. We develop a linear model of the circuit and pose a convex problem for estimating the faults and other hidden states. A sparse fault vector solution is computed by using 11 regularization. The solution is computed reliably and efficiently, and gives accurate diagnostics on the faults. We demonstrate a real-time implementation of the approach for an instrumented electrical power system testbed, the ADAPT testbed at NASA ARC. The estimates are computed in milliseconds on a PC. The approach performs well despite unmodeled transients and other modeling uncertainties present in the system.

Gorinevsky, Dimitry↗
NASA NTRS1988

Heat pipe dynamic behavior

The vapor flow in a heat pipe was mathematically modeled and the equations governing the transient behavior of the core were solved numerically. The modeled vapor flow is transient, axisymmetric (or two-dimensional) compressible viscous flow in a closed chamber. The two methods of solution are described. The more promising method failed (a mixed Galerkin finite difference method) whereas a more common finite difference method was successful. Preliminary results are presented showing that multi-dimensional flows need to be treated. A model of the liquid phase of a high temperature heat pipe was developed. The model is intended to be coupled to a vapor phase model for the complete solution of the heat pipe problem. The mathematical equations are formulated consistent with physical processes while allowing a computationally efficient solution. The model simulates time dependent characteristics of concern to the liquid phase including input phase change, output heat fluxes, liquid temperatures, container temperatures, liquid velocities, and liquid pressure. Preliminary results were obtained for two heat pipe startup cases. The heat pipe studied used lithium as the working fluid and an annular wick configuration. Recommendations for implementation based on the results obtained are presented. Experimental studies were initiated using a rectangular heat pipe. Both twin beam laser holography and laser Doppler anemometry were investigated. Preliminary experiments were completed and results are reported.

Issacci, F.↗
DOE OSTI2023

Dissolved gas recovery from water using a sidestream hollow-fiber membrane module: First principles model synthesis and steady-state validation

This paper presents a first-principles model for the recovery of dissolved gases from liquids using a sidestream hollow-fiber membrane module. The model avoids the use of new empirical coefficients, thus providing a parametric understanding of the process behavior for future design and optimization of membrane modules. This type of first-principles model could be particularly useful when gas recovery is beneficial to biological or chemical reactions of interest, such as the acetogenesis reactions in two-stage anaerobic digesters. The steady-state behavior of the model was validated against both new experimental data for the recovery of H 2 , CH 4 and H 2 –CH 4 mixtures from pure water, as well as existing published data. The modeled gas recovery predictions agreed with experimental data to an absolute average error of 13%, and an average R value of 0.98. Parametric analysis of mixed-gas recovery suggests possible key transition points in the composition of the recovered gases. For example, at 40 °C, increasing trans-membrane pressure while keeping hydraulic residence time (HRT) under 0.5 s will result in an increase in the ratio of H 2 to CH 4 recovered. Otherwise, increasing trans-membrane pressure will instead decrease the ratio of H 2 to CH 4 recovered. The model has potential to be extended to transient analysis, but has yet to be validated with transient experimental data. Furthermore, this model was successfully implemented in both Python and MATLAB, and provides valuable insights for future net-energy optimization for anaerobic digestion systems with in-situ gas recovery.

Anaerobic Digestion↗
NASA NTRS1974

Application of a parameter identification technique to a hingeless helicopter rotor

A mathematical model of a gyro-controlled, three-bladed hingeless helicopter rotor was developed and parameters of the model were estimated using a parameter identification technique. The flapping and feathering degrees of freedom of the blades were modeled. The equations of the model contain time-varying, periodic coefficients due to the forward speed of the rotor. A digital simulation of the analytical model was compared with wind-tunnel measurements to establish the validity of the model. Comparisons of steady-state and transient solutions of the analytical model with the tunnel measurements gave reasonably good matching of gyro angle but less satisfactory matching of hub moment measurements. Further improvements were obtained by use of a parameter identification technique to adjust as many as 10 parameters of the analytical model. The sensitivity of the blade response to small changes in the parameters was also calculated.

Kanning, G.↗
DOE OSTI2025

Modeling Co2 Flow Through Faulted/Fractured Reservoirs Using Tedfm in Corner-Point Grids

Interest in underground CO2 storage has increased significantly over the last decade, driven by growing concern about global warming and rising levels of greenhouse gases in the atmosphere. Given that CO2 accounts for 80% of these greenhouse gases, carbon capture, utilization, and storage (CCUS) is considered one of the most direct approaches to achieving the net-zero carbon target. Although CO2 storage in deep saline aquifers and depleted gas reservoirs has been studied extensively, most studies use commercial simulators that model faults/fractures by simply modifying the transmissibility in the direction perpendicular to the fault surfaces. This work shows that this simplistic approach ignores the accelerated flow in the directions parallel to the fault plane, leading to significantly higher leakage along the fault surface. To accurately model CO2 flow in faulted reservoirs, we present the first transient embedded discrete-fracture model for corner-point grids (tEDFM-CPG). By comparing the tEDFM-CPG results with high-resolution reference solutions, we show that this approach is accurate and efficient at predicting CO2 flow in faulted/fractured reservoirs. In conclusion, this work presents the use of mixed reality (MR) to efficiently observe CO2 gas migration in the interior of these corner-point grid systems.

02 PETROLEUM↗