Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TEMPERATURE GRADIENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Nanoporous Silica Thermal Insulation for Space Shuttle Cryogenic Tanks: A Case Study

Nanoporous silica (with typical 10-50 nm porous radii) has been benchmarked for thermal insulators capable of maintaining a 150 K/cm temperature gradient. For cryogenic use in aerospace applications, the combined features for low-density, high thermal insulation factors, and low temperature compatibility are demonstrated in a prototype sandwich structure between two propulsion tanks. Theoretical modelling based on a nanoscale fractal structure suggest that the thermal conductivity scales proportionally (exponent, 1.7) with the material density-lower density increases the thermal insulation rating. Computer simulations, however, support the optimization tradeoff between material strength (Young moduli, proportional to density with exponent, 3.7), the characteristic (colloidal silica, less than 5 nm) particle size, and the thermal rating. The results of these simulations indicate that as nanosized particles are incorporated into the silica backbone, the resulting physical properties will be tailored by the smallest characteristic length and their fractal interconnections (dimension and fractal size). The application specifies a prototype panel which takes advantage of the processing flexibility inherent in sol-gel chemistry.

Noever, David A.↗
NASA NTRS2005

Flexible Cryogenic Temperature and Liquid-Level Probes

Lightweight, flexible probes have been developed for measuring temperatures at multiple locations in tanks that contain possibly pressurized cryogenic fluids. If the fluid in a given tank is subcritical (that is, if it consists of a liquid and its vapor), then in one of two modes of operation, the temperature measurements made by a probe of this type can be used to deduce the approximate level of the liquid. The temperature sensors are silicon diodes located at intervals along a probe. If the probe is to be used to measure a temperature gradient along a given axis in the tank, then the probe must be mounted along that axis. In the temperature-measurement mode, a constant small electric current is applied to each diode and the voltage across the diode a known function of the current and temperature is measured as an indication of its temperature. For the purpose of this measurement, small electric current signifies a current that is not large enough to cause a significant increase in the measured temperature. More specifically, the probe design calls for a current of 10 A, which, in the cryogenic temperature range of interest, generates heat at a rate of only about 0.01 mW per diode. In the liquid-level-sensing mode, one applies a larger current (30 mA) to each diode so as to heat each diode appreciably (with a power of about 36 mW in the temperature range of interest). Because the liquid cools the diode faster than does the vapor, the temperature of the diode is less when the diode is immersed in the liquid than when it is above the surface of the liquid. Thus, the temperature (voltage) reading from each diode can be used to determine whether the liquid level is above or below the diode, and one can deduce that the liquid level lies between two adjacent diodes, the lower one of which reads a significantly lower temperature. The aforementioned techniques for measuring temperature and deducing liquid level are not new. What is new here are the designs of the probes and of associated external electronic circuitry. In each probe, the diodes and the lead wires are embedded in a strong, lightweight, flexible polyimide strip. Each probe is constructed as an integral unit that includes a multipin input/output plug or socket for solderless connection of the lead wires to the external circuitry. The polyimide strip includes mounting tabs with holes that can accommodate rivets, screws, or other fasteners. Alternatively, a probe can be mounted by use of an epoxy. A probe can be manufactured to almost any length or width, and the diodes can be embedded at almost any desired location along and across the polyimide strip. In designing a probe for a specific application, one seeks a compromise between (1) minimizing the number of diodes in order to minimize the complexity of input/output connections and external electronic circuitry while (2) using enough diodes to obtain the required precision. Optionally, to minimize spurious heating of the cryogenic fluid, the external circuitry can be designed to apply power to the probe only during brief measurement intervals. Assuming that the external circuitry is maintained at a steady temperature, a power-on interval of only a few seconds is sufficient to obtain accurate data on temperatures and/or the height of the liquid/vapor interface.

Haberbusch, Mark↗
NASA NTRS1994

Interactions between solidification and compositional convection in mushy layers

Mushy layers are ubiquitous during the solidification of alloys. They are regions of mixed phase wherein solid crystals are bathed in the melt from which they grew. The matrix of crystals forms a porous medium through which the melt can flow, driven either by external forces or by its own buoyancy in a gravitational field. Buoyancy-driven convection of the melt depends both on temperature gradients, which are necessary for solidification, and on compositional gradients, which are generated as certain components of the alloy are preferentially incorporated in the solid phase and the remaining components are expelled into the melt. In fully liquid regions, the combined action of temperature and concentration on the density of the liquid can cause various forms of double-diffusive convection. However, in the interior of mushy regions the temperature and concentration are thermodynamically coupled so only single-diffusive convection can occur. Typically, the effect of composition on the buoyancy of the melt is much greater than the effect of temperature, and thus convection in mushy layers in driven primarily by the computational gradients within them. The rising interstitial liquid is relatively dilute, having come from colder regions of the mushy layer, where the liquidus concentration is lower, and can dissolve the crystal matrix through which it flows. This is the fundamental process by which chimneys are formed. It is a nonlinear process that requires the convective velocities to be sufficiently large, so fully fledged chimneys (narrow channels) might be avoided by means that weaken the flow. Better still would be to prevent convection altogether, since even weak convection will cause lateral, compositional inhomogeneities in castings. This report outlines three studies that examine the onset of convection within mushy layers.

Worster, M. Grae↗
DOE OSTI2021

Gyrokinetic simulation of turbulence and transport in the SPARC tokamak

The turbulence and transport expected in the SPARC tokamak Primary Reference Discharge (PRD) [P. Rodriguez-Fernandez et al., J. Plasma Phys. 86, 865860503 (2020)] have been investigated with the gyrokinetic code CGYRO [J. Candy et al., J. Comput. Phys. 324, 73–93 (2016)]. Linear and nonlinear simulations that focus on ion (kθρs<1.0) and electron-scale (kθρs>1.0) turbulence were used to probe the nature of the turbulence and the resulting transport in the fusion core. It is found that in the SPARC PRD, ion temperature gradient (ITG) turbulence is expected to dominate transport over most of the profile with some potential trapped electron mode impact in the near edge. Stiff turbulence is observed over a part of the plasma core such that SPARC's ion temperature profile will likely be pinned to just above the critical gradient for ITG. The role of electromagnetic turbulence, rotation, and electron-scale turbulence was investigated to provide some insight into the physics required to accurately predict SPARC performance via gyrokinetics. Additionally, predictions of impurity peaking for potential low- and high-Z SPARC first-wall materials are probed using ion-scale simulation. The dominance of low-k turbulence in SPARC provides a potential opportunity for more tractable prediction of plasma profiles using nonlinear gyrokinetics. This work is the first step toward full gyrokinetic profile prediction of SPARC kinetic profiles and the resulting fusion power and plasma gain.

Howard, N. T. (ORCID:0000000287876309)↗
DOE OSTI2022

Automated Control for Nuclear Thermal Propulsion Start-Up using MOOSE-based Applications

This report presents a Griffin/Bison/RELAP-7 numerical model of a prototypical NTP system that features fuel assemblies arranged in rings, and which was designed to simulate rapid startup transients. The physics modeled include full-core neutronics, assembly-wise heat conduction, and conjugate heat transfer, with the balance of plant mainly imposed through boundary conditions. In addition, various forms of automated reactivity control were deployed by using the MOOSE to autonomously drive the model and simulate the reactor transitioning from assumed initial conditions to nominal power in a fraction of a minute. To generate the cross-sections of the neutronics model, and in an effort to simultaneously account for the tremendous axial temperature gradients in the reactor and to limit the number of state points required for cross-section generation, the average component temperatures and hydrogen densities in the cooling channels were correlated to the average fuel and moderator temperatures, and fixed axial profiles were derived for nominal conditions and then used during the transient. With this approximation, a tractable cross-section library tabulated with fuel/moderator temperatures and CD angles was generated using Serpent. The full-core SPH correction procedure and the CD decusping technology in Griffin, respectively, ensure preservation of the multiplication factor and reaction rates at state points, along with a reasonably accurate reactivity worth between tabulated CD angles, despite using a coarse mesh. Feedback from other physics was calculated by modeling one representative fuel assembly per ring, along with the corresponding fuel and moderator cooling channels. To limit power overshoots during startup, another layer of multiphysics coupling was added to the model in order to automatically control the drums. Two different technologies presented herein showed outstanding performance in this regard: (1) a novel hybrid PID controller based on both power and reactivity signals, and (2) a PGC that relies on kinetics parameters and reactivity coefficients to predict future behavior and adjust the desired signal accordingly. A challenging benchmark was devised, featuring a power demand curve that exponentially increases by a factor of 500 within 30 seconds, then levels out after that. Both control approaches create a simulated power curve that closely follows the power demand curve and limits power overshoots to 1% or less. While the former approach requires more tuning of the internal parameters, the latter requires additional knowledge of the reactivity feedback coefficients and rates of change of the corresponding variables, including fuel and moderator temperature, which could be difficult to dynamically measure for a real NTP system. Fortunately, some inaccuracy in these quantities will not drastically degrade the PGC performance. Subsequently, a more realistic startup sequence was considered, in which the mass flow rate and outlet pressures are ramped up to model bootstrap and thrust build-up phases prior to reaching steady-state conditions, demonstrating the ability of the hybrid PID and PGCs to handle such transients, with both types of controllers exhibiting very similar behavior. Nevertheless, a significant chamber temperature overshoot was observed, caused by the demanded power signal and assumed mass flow rate. This issue could be mitigated by deploying a reactor controller that follows the chamber temperature signal and actuates both the control valves and drums (rather than using a power signal based solely on the drums to control reactivity). Enhancement of the hydrogen fluid properties available in MOOSE, as well as a better understanding of prototypical initial conditions, are also needed to further enhance this startup model. Finally, a study was performed to model decay heat post-shutdown, and to prepare for extending this model to predict shutdown behavior and post-shutdown pulsed cooling requirements.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1974

Cathodoluminescence of regolith returned by Luna 16 automatic station

Observations of local variations in the intensity and spectral composition of the cathodoluminescence of lunar regolith are described. These variations are caused by structural features, by the kind and quantity of the material, and by the admixtures. In addition, cathodoluminescent emission is also associated with a change in the temperature of the lunar surface. Periodic diurnal illumination and darkening of the moon is responsible for a temperature gradient normal to the lines of longitude. These observations made of regolith, using a scanning electron microscope with an attachment for temperature variation, simulate the indicated thermal changes of the cathodoluminescent properties of lunar material.

Spivak, G. V.↗
NASA NTRS1977

Evolution of the high-temperature plasma in the 15 June 1973 flare

The evolution of the high-temperature plasma in the solar flare of June 15, 1973, is analyzed using XUV spectroheliograms obtained from Skylab. Preflare enhancement of loops in the active region is discussed, and the temperature and density of the hot plasma are determined as a function of time. The turbulent velocity in the high-temperature plasma is deduced from a comparison of line widths of the Fe XXIV doublet at 192 and 255 A. The results indicate that: (1) the flare occurred in a low-lying loop or loops; (2) the large-scale magnetic-field configuration of the active region did not change significantly; (3) the hot plasma observed in Fe XXIII-XXIV showed considerable dynamic activity, including an initial upward motion of the whole plasma with a velocity of about 80 km/s; (4) large turbulent mass motions took place in the Fe XXIII-XXIV plasma with random velocities of 100 to 160 km/s; (5) the temperature of the hot plasma was 14 million K at peak X-ray intensity, decreased slightly, and then remained at 12.6 million K before dropping to below 10 million K; and (6) there was a temperature gradient along the length of the loop, with the 14 million-K plasma near the top and progressively lower-temperature plasmas on either side.

Cheng, C.-C.↗
NASA NTRS1984

In-flight atmospheric and fuel tank temperature measurements

In order to maintain an adequate supply of aviation turbine fuels in the future, fuels may have properties different from those now currently produced. One possible change is an increase in the freezing point temperature. If this should occur, it will be necessary to know the low temperature flow characteristics of these fuels. Studies to date involved both the use of computer models and subscale fuel tank simulators. They indicate that steep temperature gradients occur near the upper and lower surfaces which can result in freezing at the bottom, even though the bulk fuel temperature is above the freezing point. In order to obtain flight data to verify computer model and simulator results, a Lockheed L1011 research aircraft at Palmdale, California was instrumented with a vertical thermocouple rake in an inboard tank and an outboard tank. The tests were conducted with one of the two instrumented tanks maintained full for either two or five hours at altitudes of at least 10668 meters (35000 ft). Other flight parameters such as Mach number, air temperature, fuel quantity, and heading were also recorded.

Svehla, R.↗
NASA NTRS1988

Nimbus-7 earth radiation budget measurements and their relationship to the energetics of the general circulation

Observations from the Nimbus-7 Earth Radiation Budget (ERB) experiment were used to examine the way in which changes in equator to pole energy gradients effect Northern Hemisphere midlatitude energetics. The results of kinetic energy calculations describing the midlatitude circulation are compared to the gradients of IR flux and NET radiation. A close relationship is found between the ERB gradient values and kinetic energy values. It is shown that the zonal wind speed and the eddy winds increase as the temperature gradient increases.

Randel, David L.↗
NASA NTRS1991

The high-pressure melting curve of iron - A technical discussion

The melting curve of iron is reliably determined to 105 GPa using the laser-heated diamond cell, in close agreement with independent measurements using piston-cylinder and large-volume presses or shock-wave experiments. In order to obtain reliable melting data from the internally heated diamond cell, whether by laser or Joule heating, temperature gradients across the sample must be quantitatively measured; otherwise, such 'wire heating' experiments can lead to significant underestimates of the melting temperature and its pressure dependence. The best estimate of the high-pressure melting curve of iron, as derived from the laser-heated diamond cell and Hugoniot temperature measurements, yields melting temperatures of 4800 + or - 200 K and 6700 + or - 400 K at 133 GPa and 243 GPa, respectively.

Williams, Quentin↗
NASA NTRS1999

Effective Thermal Conductivity of High Temperature Insulations for Reusable Launch Vehicles

An experimental apparatus was designed to measure the effective thermal conductivity of various high temperature insulations subject to large temperature gradients representative of typical launch vehicle re-entry aerodynamic heating conditions. The insulation sample cold side was maintained around room temperature, while the hot side was heated to temperatures as high as 1800 degrees Fahrenheit. The environmental pressure was varied from 0.0001 to 760 torr. All the measurements were performed in a dry gaseous nitrogen environment. The effective thermal conductivity of Saffil, Q-Fiber felt, Cerachrome, and three multi-layer insulation configurations were measured.

Daryabeigi, Kamran↗
NASA NTRS1999

Interferometer Development for Study of Interactions between Flames on Parallel Solid Surfaces

The interactions between flames spreading over parallel solid sheets of paper are being studied in normal gravity and in microgravity. This geometry provides interesting opportunities to study the interaction of radiative and diffusive transport mechanisms on the spread process. These transport mechanisms are changed when the flame interacts with other flames. Most practical heterogeneous combustion processes involve interacting discrete burning fuel elements, consequently, the study of these interactions is of practical significance. Owing largely to this practical importance, flame interactions have been an area of active research, however microgravity research has been largely limited to droplets. Consideration of flame spread over parallel solid surfaces has been limited to 1-g studies. To study the conductive transport in these flames, an interferometer system has been developed for use in the drop tower. The system takes advantage of a single beam interferometer: Point Diffraction Interferometry (PDI) which uses a portion of the light through the test section to provide the reference beam. Like other interferometric and Schlieren systems, it is a line of sight measurement and is subject to the usual edge and concentration effects. The advantage over Schlieren and shearing interferometry systems is that the fringes are lines of constant index of refraction rather than of its gradient so the images are more readily interpreted. The disadvantage is that it is less able to accommodate a range of temperature gradients.

Goldmeer, J. S.↗
NASA NTRS2004

Brine Pockets in the Icy Shell on Europa: Distribution, Chemistry, and Habitability

On Earth, sea ice is rich in brine, salt, and gas inclusions that form through capturing of seawater during ice formation. Cooling of the ice over time leads to sequential freezing of captured sea-water, precipitation of salts, exsolution of gases, and formation of brine channels and pockets. Distribution and composition of brines in sea ice depend on the rate of ice formation, vertical temperature gradient, and the age of the ice. With aging, the abundance of brine pockets decreases through downward migration. De- spite low temperatures and elevated salinities, brines in sea ice provide a habitat for photosynthetic and chemosynthetic organisms. On Europa, brine pockets and channels could exist in the icy shell that may be from a few km to a few tens of km thick and is probably underlain by a water ocean. If the icy shell is relatively thick, convection could develop, affecting the temperature pattern in the ice. To predict the distribution and chemistry of brine pockets in the icy shell we have combined numerical models of the temperature distribution within a convecting shell, a model for oceanic chemistry, and a model for freezing of Europan oceanic water. Possible effects of brine and gas inclusions on ice rheology and tectonics are discussed.

Zolotov, M. Yu↗
NASA NTRS1992

Sea surface velocities from visible and infrared multispectral atmospheric mapping sensor imagery

High resolution (100 m), sequential Multispectral Atmospheric Mapping Sensor (MAMS) images were used in a study to calculate advective surface velocities using the Maximum Cross Correlation (MCC) technique. Radiance and brightness temperature gradient magnitude images were formed from visible (0.48 microns) and infrared (11.12 microns) image pairs, respectively, of Chandeleur Sound, which is a shallow body of water northeast of the Mississippi delta, at 145546 GMT and 170701 GMT on 30 Mar. 1989. The gradient magnitude images enhanced the surface water feature boundaries, and a lower cutoff on the gradient magnitudes calculated allowed the undesirable sunglare and backscatter gradients in the visible images, and the water vapor absorption gradients in the infrared images, to be reduced in strength. Requiring high (greater than 0.4) maximum cross correlation coefficients and spatial coherence of the vector field aided in the selection of an optimal template size of 10 x 10 pixels (first image) and search limit of 20 pixels (second image) to use in the MCC technique. Use of these optimum input parameters to the MCC algorithm, and high correlation and spatial coherence filtering of the resulting velocity field from the MCC calculation yielded a clustered velocity distribution over the visible and infrared gradient images. The velocity field calculated from the visible gradient image pair agreed well with a subjective analysis of the motion, but the velocity field from the infrared gradient image pair did not. This was attributed to the changing shapes of the gradient features, their nonuniqueness, and large displacements relative to the mean distance between them. These problems implied a lower repeat time for the imagery was needed in order to improve the velocity field derived from gradient imagery. Suggestions are given for optimizing the repeat time of sequential imagery when using the MCC method for motion studies. Applying the MCC method to the infrared brightness temperature imagery yielded a velocity field which did agree with the subjective analysis of the motion and that derived from the visible gradient imagery. Differences between the visible and infrared derived velocities were 14.9 cm/s in speed and 56.7 degrees in direction. Both of these velocity fields also agreed well with the motion expected from considerations of the ocean bottom topography and wind and tidal forcing in the study area during the 2.175 hour time interval.

Pope, P. A.↗
NASA NTRS1980

On the force-restore method for prediction of ground surface temperature

The force-restore method for prediction of ground surface temperature is investigated in view of the large temperature gradient that generally exists on a bare ground surface after an extended period of evaporation. The rate equation for the 'ground surface' temperature is rederived. The result from a numerical experiment indicates that there can be significant differences in the diurnal variation of ground surface temperature depending upon its definition. The method was tested by a simulation study of two field-measured data sets at different experiment sites.

Lin, J. D.↗
NASA NTRS1988

Bithermal fatigue: A simplified alternative to thermomechanical fatigue

A bithermal fatigue test technique was proposed as a simplified alternative to the thermomechanical fatigue test. Both the thermomechanical cycle and the bithermal technique can be used to study nonisothermal fatigue behavior. The difference between the two cycles is that in a conventional thermomechanical fatigue cycle the temperature is continuously varied concurrently with the applied mechanical strains, but in the bithermal fatigue cycle the specimen is held at zero load during the temperature excursions and all the loads are applied at the two extreme temperatures of the cycle. Experimentally, the bithermal fatigue test technique offers advantages such as ease in synchronizing the temperature and mechanical strain waveforms, in minimizing temperature gradients in the specimen gauge length, and in reducing and interpreting thermal fatigue such as the influence of alternate high and low temperatures on the cyclic stress-strain response characteristics, the effects of thermal state, and the possibility of introducing high- and low-temperature deformation mechanisms within the same cycle. The bithermal technique was used to study nonisothermal fatigue behavior of alloys such as single-crystal PWA 1480, single-crystal Rene N4, cast B1900+Hf, and wrought Haynes 188.

Verrilli, Michael J.↗
NASA NTRS1991

Energy balance and plume dynamics in Triton's lower atmosphere

The present study of the thermal balance-affecting relationships among Triton lower atmosphere thermal conduction, eddy mixing, condensation, and radiative heating indicates that, while the temperature gradient is negative in the lower atmosphere, it becomes positive at higher altitudes due to the downward conduction of ionospheric heat. This temperature profile is essentially consistent with radio-occultation experiment data; the geyser-like plumes observed by Voyager suggest that the Trioton atmosphere's convective and conductive regions join near 10-km altitude, and that the values inferred for the eddy diffusion and heat-transport coefficients indicate a profile reminiscent of the earth's.

Yelle, Roger V.↗
NASA NTRS1991

Dynamical behavior of strong magnetic fields in the solar convection zone

Magnetic buoyancy is thought to play an important role in the dynamical behavior of the sun's magnetic field in the convection zone. Magnetic buoyancy is commonly thought to cause inescapable rapid loss of toroidal flux from much of the convection zone, thereby suppressing effective operation of a solar dynamo. This paper reexamines the detailed character of magnetic buoyancy, especially as it is influenced by the magnetic field's effect on heat transport and temperature gradients in the convection zone. It is suggested that suppression of convective heat transport across strong magnetic flux tubes can alter the temperature within the tubes and can subdue, or even reverse, the effect of magnetic buoyancy.

Vainshtein, S.↗