Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stress Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Computational Analysis of Water Film Thickness During Rain Events for Assessing Hydroplaning Risk Part 2: Rough Road Surfaces

Hydroplaning occurs when a water film forms on a road during a rain event and vehicles are traveling at a speed that does not provide sufficient time for the tires to push the water film out of the tire path. Under these conditions, the tire loses contact with the road and the driver may lose control over the vehicle. The present study is a part of a multiyear research effort aimed at gaining a better understanding of the factors that contribute to hydroplaning risk in order to minimize the occurrence of hydroplaning accidents. Three-dimensional computational fluid dynamics (CFD) analysis was used to investigate the water film thickness on multilane roads, one of the key parameters in evaluating hydroplaning risk. In the first part of the study, water films forming on wide roadways, i.e. multilane highways with 2, 4, and 6 lanes per side, were analyzed, with varying cross slope, longitudinal slope, and rainfall rate. Roadways with and without curbs and drainage were included in the analysis. The analysis in the first part was limited to nearly smooth asphalt or concrete surfaces because the maximum roughness height that can be specified in a CFD model using wall functions to determine shear stress at the road surface boundary is one half the thickness of computational cell layer adjacent to the boundary and the need to resolve the vertical velocity distribution in a thin water film requires cell layers that are a fraction of a millimeter thick. In this part of the study, the analysis was extended to consider the influence of pavement roughness over a range extending up 3.6 mm on the development of water film thickness. Various methods of modeling roughness were investigated and are presented: the roughness height model, a meshed-out geometry of the macrotexture of the pavement, and a porous region model. The computational results were analyzed and compared with experimental measurements performed by Gallaway et al.

42 ENGINEERING↗
DOE OSTI2020

Low Mach number fluctuating hydrodynamics model for ionic liquids

We present a new mesoscale model for ionic liquids based on a low Mach number fluctuating hydrodynamics formulation for multicomponent charged species. The low Mach number approach eliminates sound waves from the fully compressible equations leading to a computationally efficient incompressible formulation. The model uses a Gibbs free energy functional that includes enthalpy of mixing, interfacial energy, and electrostatic contributions. These lead to a new fourth-order term in the mass equations and a reversible stress in the momentum equations. We calibrate our model using parameters for [DMPI+][F6P-], an extensively-studied room temperature ionic liquid (RTIL), and numerically demonstrate the formation of mesoscopic structuring at equilibrium in two and three dimensions. In simulations with electrode boundaries the measured double layer capacitance decreases with voltage, in agreement with theoretical predictions and experimental measurements for RTILs. Finally, we present a shear electroosmosis example to demonstrate that the methodology can be used to model electrokinetic flows.

42 ENGINEERING↗
DOE OSTI2022

Transitions in the morphology and critical stresses of gliding dislocations in multiprincipal element alloys

Refractory multiprincipal element alloys (MPEAs) are promising material candidates for high-temperature, high-strength applications. However, their deformation mechanisms, particularly at the dislocation scale, are unusual compared to those of conventional alloys, making it challenging to understand the origin of their high strength. Here, using an atomistically informed phase-field dislocation dynamics model, we study transitions in the morphology and critical stresses of long gliding screw dislocations over extended distances in a refractory MPEA. The model MPEA crystal accounts for the atomic-scale fluctuations in chemical composition across the glide planes via spatially correlated lattice energies and for the differences in glide resistances between screw and edge dislocations of unit length. Here, we show that the dislocation moves in a stop-start motion, alternating between wavy morphology in free flight and nearly recovered straight screw orientation in full arrest. The periods of wavy glide are due to variable kink-pair formation and migration rates along the length, where portions with higher rates glide more quickly. The critical stress to initiate motion corresponds to the stress required to form and migrate a kink pair at the weakest region along the length of the dislocation. Heterogeneity in lattice energy leads to variability in the local stress-strain response and to a strain hardening-like response, in which the critical stress to reactivate glide increases with glide distance. Statistical assessment of hundreds of realizations of dislocations indicates that the amount of hardening directly scales with the dispersion in underlying lattice energy.

3-dimensional systems↗
DOE OSTI2024

Theoretical design and performance of three-dimensional, pillared FeS 2 cathodes

Three-dimensional (3D) electrode design can provide improved capacities and rate capabilities over conventional two-dimensional electrodes by enhancing electrical and ionic transport. Here, expanding upon our previous modeling efforts for conversion chemistry lithium-ion batteries, we develop a pseudo-four-dimensional (P4D) approach that is subsequently used to investigate the design of a pillared FeS 2 electrode. The model considers transport in three dimensions with an additional “fourth” dimension corresponding to the solid-state lithium transport within the active material particles. Additionally, we allow for expansion of the active material during the conversion reaction to understand how internal stresses impact the electrochemical performance of the cell. By optimizing the model with respect to areal capacity, we are able to predict areal capacities up to 16.8 mAh/cm 2 for an areal current density of 1.78 mA/cm 2 and a 103% improvement for the three-dimensional electrodes over planar electrodes of equal volume. Despite the promising results, our simulations suggest that 3D design may be difficult for conversion cathode materials due to the large internal stresses that arise during conversion. Nevertheless, the model is robust and adaptable to other materials that may be more suitable for 3D electrodes due to a lesser change in volume during discharge.

Conversion cathode materials↗
DOE OSTI2021

Experimental workflow to estimate model parameters for evaluating long term viscoelastic response of CO2 storage caprocks

Understanding the time-dependent behavior of reservoir and sealing formations is critical to assessing risks associated with geological carbon storage since time-dependent deformation strongly influences mechanical responses of some rock types. Many studies have evaluated the risk of CO2 leakage and induced seismicity by assuming poroelastic rheology in sealing formations. Few have considered viscoelastic or other time-dependent responses, where the existing literature adopts 1D models to represent long-term time-dependent responses. This is primarily because to date, the general form of a reasonable 3D time-dependent model for rocks remains unclear. In this paper, we address this unclear issue by proposing a new workflow to select constitutive modeling parameters to evaluate if a 3D viscoelastic model is reasonable using several-hour-long experimental data and a power-law response to extrapolate to the decades-long time frames of interest in geologic carbon storage. To provide experimental data, we conducted multi-level loading/unloading triaxial relaxation tests with four rock types. The experimental results showed that the maximum load relaxation observed is approximately 49%, with some rock types showing as little as 1.4%. Using a simple linear viscoelastic model, parameters were chosen such that a maximum deviation of 1.5 MPa in axial stress and 7 MPa in radial stress was attained with the extrapolated 30-year data. We found that a reasonable parameter range for the normalized elastic modulus is 0.1~2 for rocks with significant time-dependent responses and 0.01~0.06 for those with small time-dependent responses. No matter how significant time-dependent responses are for rocks considered, our results showed that the relaxation time has a general range of 1~10^10 s, whose time scale can be one or two orders higher than a time frame typically envisioned for CO2 injection projects.

Stress relaxation, 3D time-dependent model, viscoe↗
DOE OSTI2020

Multiscale Approach to Fast ModSim for Laser Processing of Metals for Future Nuclear Deterrence Environments

Predicting performance of parts produced using laser-metal processing remains an out- standing challenge. While many computational models exist, they are generally too computationally expensive to simulate the build of an engineering-scale part. This work develops a reduced order thermal model of a laser-metal system using analytical Green's function solutions to the linear heat equation, representing a step towards achieving a full part performance prediction in an "overnight" time frame. The developed model is able to calculate a thermal history for an example problem 72 times faster than a traditional FEM method. The model parameters are calibrated using a non-linear solution and microstructures and residual stresses calculated and compared to a non-linear case. The calibrated model shows promising agreement with a non-linear solution.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Automating Component-Level Stress Measurements for Inverter Reliability Estimation

In the near future, grid operators are expected to regularly use advanced distributed energy resource (DER) functions, defined in IEEE 1547-2018, to perform a range of grid-support operations. Many of these functions adjust the active and reactive power of the device through commanded or autonomous operating modes which induce new stresses on the power electronics components. In this work, an experimental and theoretical framework is introduced which couples laboratory-measured component stress with advanced inverter functionality and derives a reduction in useful lifetime based on an applicable reliability model. Multiple DER devices were instrumented to calculate the additional component stress under multiple reactive power setpoints to estimate associated DER lifetime reductions. A clear increase in switch loss was demonstrated as a function of irradiance level and power factor. This is replicated in the system-level efficiency measurements, although magnitudes were different—suggesting other loss mechanisms exist. Using an approximate Arrhenius thermal model for the switches, the experimental data indicate a lifetime reduction of 1.5% when operating the inverter at 0.85 PF—compared to unity PF—assuming the DER failure mechanism thermally driven within the H-bridge. If other failure mechanisms are discovered for a set of power electronics devices, this testing and calculation framework can easily be tailored to those failure mechanisms.

Flicker, Jack (ORCID:0000000212232154)↗
DOE OSTI2020

Multiscale Thermomechanical Damage Model with Internal State Variables for Ceramic Matrix Composites

A length scale-dependent matrix damage model has been developed to simulate the response of ceramic matrix composites (CMCs). This model captures damage initiation and propagation in the brittle matrix material by employing internal state variable (ISV) theory within a multiscale modeling framework to obtain damaged matrix stress-strain constitutive relationships at each length scale. Material degradation due to matrix cracking is captured by a damage variable determined using fracture mechanics and the self-consistent scheme. An additional state variable is introduced to capture the nucleation and growth of matrix porosity, a key mechanism contributing to matrix nonlinearity. Porosity occurs as a result of material diffusion around grain boundaries and the growth of the porosity state variable is related to the material entropy dissipation and the volumetric strain. The nonlinear predictive capabilities of the material model are demonstrated for monolithic silicon carbide, unidirectional (UD) carbon fiber/silicon carbide matrix (C/SiC) CMC, and five-harness satin (5HS) woven C/SiC CMC.

Skinner, Travis D.↗
DOE OSTI2022

Understanding thermal and mechanical effects on lithium plating in lithium-ion batteries

Lithium plating is one of the main concerns for cell durability, as cyclable lithium and cell capacity are decreased during the process. Thermal and mechanical loads can influence cell behavior, including lithium plating driving forces, as suggested by the Arrhenius equation and the Bruggeman relation, respectively. Hence, a 1D and a 3D model are employed to study the thermal and mechanical effects on lithium plating in a lithium-ion battery with a high areal capacity (4 mAh/cm 2 ). The 1D model assumes uniform mechanical and temperature profile, while the 3D model is capable of capturing the nonuniformity of stress and temperature in the cell. Further, the effects of mechanical deformation and different temperatures on the process of lithium plating are investigated in this study. With the help of the 1D charging simulations, it is observed that lower temperatures increase the risk of lithium plating and the presence of mechanical deformations can accelerate its initiation. Furthermore, 3D charging simulations indicated that folds and boundaries of jellyrolls are more susceptible to lithium plating due to the higher stress concentration and lower temperature, respectively.

25 ENERGY STORAGE↗
DOE OSTI2021

Applicability of discrete element method with spherical and clumped particles for constitutive study of granular materials

Discrete element method (DEM) has been intensively used to study the constitutive behaviour of granular materials. However, to what extent a real granular material can be reproduced by virtual DEM simulations remains unclear. This study attempts to answer this question by comparing DEM simulations with typical features of experimental granular materials. Three groups of models with spherical and clumped particles are investigated from four perspectives: (i) deviatoric stress and volumetric behaviour; (ii) critical state behaviour; (iii) stress-dilatancy relationship; and (iv) the evolution of principal stress ratio against axial strain. The results demonstrate that DEM with spherical or clumped particles is capable of qualitatively describing macroscopic deviatoric stress responses, volumetric behaviour, and critical state behaviour observed in experiments for granular materials. On the other hand, some qualitative deviations between experiments and the investigated DEM simulations are also observed, in terms of the stress-dilatancy behaviour and principal stress ratio against axial strain, which are proven to be critical for constitutive modelling. The results demonstrate that DEM with spherical or clumped particles may not necessarily fully capture experimental features of granular materials even from a qualitative perspective. It is thus encouraged to thoroughly validate DEM with experiments when developing constitutive models based on DEM observations.

58 GEOSCIENCES↗
DOE OSTI2024

Different model assumptions about plant hydraulics and photosynthetic temperature acclimation yield diverging implications for tropical forest gross primary production under warming

Tropical forest photosynthesis can decline at high temperatures due to (1) biochemical responses to increasing temperature and (2) stomatal responses to increasing vapor pressure deficit (VPD), which is associated with increasing temperature. It is challenging to disentangle the influence of these two mechanisms on photosynthesis in observations, because temperature and VPD are tightly correlated in tropical forests. Nonetheless, quantifying the relative strength of these two mechanisms is essential for understanding how tropical gross primary production (GPP) will respond to climate change, because increasing atmospheric CO 2 concentration may partially offset VPD-driven stomatal responses, but is not expected to mitigate the effects of temperature-driven biochemical responses. We used two terrestrial biosphere models to quantify how physiological process assumptions (photosynthetic temperature acclimation and plant hydraulic stress) and functional traits (e.g., maximum xylem conductivity) influence the relative strength of modeled temperature versus VPD effects on light-saturated GPP at an Amazonian forest site, a seasonally dry tropical forest site, and an experimental tropical forest mesocosm. By simulating idealized climate change scenarios, we quantified the divergence in GPP predictions under model configurations with stronger VPD effects compared with stronger direct temperature effects. Assumptions consistent with stronger direct temperature effects resulted in larger GPP declines under warming, while assumptions consistent with stronger VPD effects resulted in more resilient GPP under warming. Furthermore, our findings underscore the importance of quantifying the role of direct temperature and indirect VPD effects for projecting the resilience of tropical forests in the future, and demonstrate that the relative strength of temperature versus VPD effects in models is highly sensitive to plant functional parameters and structural assumptions about photosynthetic temperature acclimation and plant hydraulics.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

The Hard Life of Floatovoltaics: Modeling Wind-Driven Oscillations of Floating Solar Panels

Modern, thin photovoltaic (PV) panels for solar power are susceptible to high stress loads in windy conditions. Manufacturers are eager to determine optimal installation practices to reduce these loads, including in the relatively new practice of installing PV on floating structures located on artificial and natural lakes. As part of our effort to develop simulation capabilities for stress on such floating PV systems, we here present our combined model-simulation approach, which simulates the dynamic wind loading and uses modeled elements to capture both the hydrodynamic and mooring-line forces. We discuss the forces important for our model and the challenges inherent in our simulation. Of particular interest is our model of the hysteresis response displayed by the attached mooring lines, which are engineered to damp motion and oscillation of the floating panel system. We validate our approach against the benchmark problem of vortex-induced vibration of a cylinder, which is driven by the same dynamic forces present in floating PV panels.

floating↗
DOE OSTI2022

A concurrent irradiation-mechanics multiscale coupling model

The vast majority of our current knowledge regarding the basic mechanisms controlling irradiation effect on mechanical properties is based almost entirely on the results of post-irradiation experiments or theoretical models. However, the concurrent effects of irradiation, mechanical stress, and thermal damage on the failure phenomena of materials and components remain largely unexplored due to its internal multiscale-multiphysics coupling nature. Here, we present here a concurrent irradiation-mechanics multiscale coupling model. The concurrent evolutions of nanoscale irradiation defect clusters, microscale dislocation configurations, and mechanical responses are well captured based on coupling cluster dynamics, discrete dislocation dynamics, and the finite element methods using an effective time marching scheme. Model predictions of defect densities and size are in general agreement with experimental observations. Irradiation hardening is shown to take place also in samples undergoing concurrent irradiation-mechanical loading, similar to samples tested post-irradiation. However, the occurrence of plastic flow localization and dislocation channel formation is not accompanied with apparent yield drop (softening) under concurrent irradiation-mechanical loading conditions, which is different from the post-irradiation case.

42 ENGINEERING↗
DOE OSTI2022

Collapse of helium-filled voids in extreme deformation: Dislocation mechanisms

The mechanisms responsible for the collapse of helium-filled bubbles during the passage of shock waves in monocrystalline copper are revealed. Both internal pressure (caused by pre-existing helium atoms) and bubble size are varied in molecular dynamics simulations to understand the atomistic scale deformation as they are subjected to shock compression at pressures of 48, 123, and 170 GPa, corresponding to particle velocities of 1.0, 2.0, and 2.5 km/s. Both empty and helium filled bubbles serve as dislocation sources, generating intense, localized plastic regions. There are distinct differences in the collapse of empty voids compared to He-filled bubbles, the former requiring less stress and generating a greater density of dislocations for a given shock strength. Additionally, a generalized model for dislocation emission is proposed, where the inclusion of shear stress generated by the helium bubble increases the critical stress to generate dislocations at the defect surface, demonstrating the change in plastic deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of a Ductile Rupture Failure Surface for PH13-8Mo H950 Steel Using the Xue-Wierzbicki Failure Model

The ability to model ductile rupture in metal parts is critical in highly stressed applications. The initiation of a ductile fracture is a function of the plastic strain, the stress state, and stress history. This paper develops a ductile rupture failure surface for PH13-8Mo H950 steel using the Xue-Wierzbicki failure model. The model is developed using data from five tensile specimen tests conducted at -40⁰C and 20⁰C. The specimens are designed to cover a Lode parameter range of 0 and 1 with a stress triaxiality range from zero in pure shear to approximately 1.0 in tension. The failure surface can be implemented directly into the finite element code or used as a post processing check.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A surprising proliferation of detwinning in β -tin at extreme loading rates

Integrating data from dynamic compression experiments of condensed matter across three national laboratories has led to insight and quantitative calibration of materials strength over decades of loading rate. For many materials, a single strength model (such as PTW) is sufficient to capture the flow-stress strain rate relationship which is monotonic. Here, we show here that β -tin, a tetragonal metal, exhibits dramatic deviations from this behavior. Naive fitting to a single PTW model is insufficient to capture the behavior; indeed, such resulting inferred flow stress versus strain exhibits a non-monotonic behavior. We suggest a resolution to this by proposing that in β -tin there are important Bauschinger effects arising from favorable conditions for twinning and detwinning. A simple yield surface model when paired with PTW hardening captures the experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Evaluation of the cytotoxic and cellular proteome impacts of food-grade TiO2 (E171) using simulated gastrointestinal digestions and a tri-culture small intestinal epithelial model

Engineered nanomaterials (ENMs) are widely used in the food industry; however, regulations for ENMs in food are still in the early stages of development due to insufficient health data. This study investigated the cytotoxicity and changes to the proteomic profile in an in vitro small intestinal epithelium model after exposure to digested food models containing the ubiquitous engineered particulate food additive, TiO2 (E171). TiO2 at 0.75% or 1.5% (w/w) concentrations in either a fasting food model (FFM) or a standardized food model (SFM) based on American diet were digested using an in vitro oral-gastric-small intestinal simulator, and the resulting digestas were applied to a small intestinal epithelium tri-culture cellular model. Effects on cell layer integrity, cytotoxicity, and oxidative stress were assessed. In order to explore impact on cellular processes beyond basic cytotoxicity, mass spectrometrybased quantitative proteomic analyses of control and exposed tri-culture cells was performed. TiO2 in FFM, but not in SFM, produced significant, dose-dependent cytotoxicity, and at the higher dose caused significant oxidative stress, indicative of a food matrix effect. No significant perturbations of the cellular proteome were observed with TiO2 in either FFM or SFM food models. However, proteins involved in the tricarboxylic acid (TCA) cycle, gluconeogenesis, and translation were up-regulated by digestas from SFM compared to those from FFM, also indicative of food matrix effects in the case of food models alone. Interestingly, the differences in profiles between the two food models was more pronounced in the presence of TiO2 indicative of food matrix effects. Together, these results indicate that TiO2 in a fasting diet may be slightly cytotoxic, and that ingested TiO2 does not significantly alter the epithelial proteome, whereas the food matrix alone can have a dramatic effect on the proteome.

Cao, Xiaoqiong↗
DOE OSTI2024

Crystal plasticity modeling and analysis for the transition from intergranular to transgranular failure in nickel-based alloy Inconel 740H at elevated temperature

The precipitation-strengthened Nickel alloy Inconel® 740H® (IN740H) exhibits increased ductility at higher applied strain rates during quasi-static tensile tests at an elevated temperature of 760°C. The examination of fracture surfaces in this context reveals a noteworthy transition of underlying fracture mechanisms from transgranular to intergranular fracture as the applied strain rate decreases from 1×10 -3 / s to 0.83×10 -4 / s . To thoroughly understand the mechanical response of IN740H under these conditions, this study develops a crystal plasticity finite element (CPFE) model. Further, this model incorporates various deformation mechanisms including dislocation slips, climb, and grain boundary sliding, which are relevant to the test conditions. The model is calibrated using data from both tensile tests at different strain rates and creep tests across a broad stress range at 760°C, enabling the accurate determination of model parameters for each mechanism. Simulation results well captured the experimental observations of different failure modes. At higher strain rates, the model shows a dominance of dislocation slip leading to heterogeneous plastic deformation and formation of transgranular shear bands causing the failure, while at lower strain rates, an increased activity of grain boundary sliding causes grain boundaries crack leading to intergranular failure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗