Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Strain improvement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Mechanical creep testing and characterization of Cr coated Zircaloy

Zirconium based cladding has been developed for use in light water reactor fuel applications due to the material’s desirable low neutron scattering cross section. To help improve corrosion resistance in accident conditions, such as a loss of coolant accident (LOCA), a chromium coating can be applied to the outer diameter of the Zircaloy tube. Cladding strength at reactor relevant temperatures is important for the structural performance. Stress relaxation creep testing was performed on Cr coated Zircaloy-4 to measure strain rate as a function of stress for 350 and 650°C. These were performed at both 5 ± 1 % and 7.5 ± 1 % strain. The lower temperature provides results near normal operating temperature, while the higher temperature provides results relevant to off-normal conditions where recrystallization will take place. Characterization was also performed to analyze the structure of the Cr coating and Zircaloy-4 as well as the interface between the two.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Texture and microstructure evolution in thermomechanically processed Mg-Ca and Mg-Zn-Ca alloys

Mg-Zn-Ca alloys have the potential for producing Mg alloy sheets with weaker basal textures and therefore improved formability. Thermomechanical processing (TMP) also plays a substantial role in determining the final sheet texture. The interplay of these variables, TMP and alloying, complicates comparisons of alloys across the literature. This work systematically explores the texture evolution and recrystallization behavior in Mg-Ca and Mg-Zn-Ca alloys during plane strain compression (PSC) using a Gleeble thermomechanical simulator. It is demonstrated that the basal texture intensity and texture characteristics change significantly during post-deformation annealing, particularly in the ternary alloys. It is also shown that careful selection of the TMP processing variables used during PSC is essential to producing weak textures. In particular, it is important to limit the recrystallization that occurs between compressive hits. This is achieved by adjusting solute content, strain rate, and the duration of the soak between passes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Simultaneous improvement in strength and ductility in 7xxx Al through a combination of natural aging and deformation

Room temperature processing methods of reaching near-T6 yield and ultimate tensile strength in Al–Zn–Mg–Cu alloys provide a potentially lower cost alternative to high temperature forming and post-forming artificial aging methods. Here, this study demonstrates a method, where a combination of pre-deformation and natural aging matched T6 strength along with ductility and strain hardening greater than the T6 values. Tensile deformation of 5% and 10% was applied to naturally aged samples at 144 h (6 days) and the samples were further naturally aged up to 220 days. The pre-deformed samples showed strong type A Portevin-Le Chatelier (PLC) banding with limited ductility and strain hardenability. Further natural aging increased both strength and ductility simultaneously and converted PLC to type B. This resulted in the same yield strength as T6 temper in the 10% deformed sample but with almost 77% greater total ductility (including the 10% pre-deformation). The simultaneous increase in strength and ductility was attributed to the small, shearable clusters/precipitates and solutes present in the microstructure as suggested by the changes in the PLC behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tacky Elastomers to Enable Tear-Resistant and Autonomous Self-Healing Semiconductor Composites

Mechanical failure of π-conjugated polymer thin films is unavoidable under cyclic loading conditions, due to intrinsic defects and poor resistance to crack propagation. Here, the first tear-resistant and room-temperature self-healable semiconducting composite is presented, consisting of conjugated polymers and butyl rubber elastomers. This new composite displays both a record-low elastic modulus (<1 MPa) and ultrahigh deformability with fracture strain above 800%. More importantly, failure behavior is not sensitive to precut notches under deformation. Autonomous self-healing at room temperature, both mechanical and electronic, is demonstrated through the physical contact of two separate films. The composite film also shows device stability in the ambient environment over 5 months due to much-improved barrier property to both oxygen and water. Butyl rubber is broadly applicable to various p-type and n-type semiconducting polymers for fabricating self-healable electronics to provide new resilient electronics that mimic the tear resistance and healable property of human skin.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Tuning the Mechanical and Electric Properties of Conjugated Polymer Semiconductors: Side–Chain Design Based on Asymmetric Benzodithiophene Building Blocks

Understanding molecular design rules for stretchable polymer semiconductors is important for enabling next generation stretchable electronic circuits. To simultaneously improve both electrical properties and mechanical stretchability, a design strategy is reported in introducing conjugated rigid fused-rings with bulky side groups in semiconducting polymers. In this work, the understanding of this design concept is improved by systematically investigating the effect of different types of bulky side groups asymmetrically substituted on conjugated polymer semiconductor backbones. Specifically, four types of side groups are investigated, including naphthalene (NaPh), biphenyl (PhPh), thienylphenyl (ThPh), and alkylphenyl (C4Ph), asymmetrically substituted on benzodithiophene units, namely asy-BDT. With the four types of side groups installed on BDT-containing conjugated polymers in an asymmetrical fashion, it is observed that they reduced the polymer chain aggregation and film crystallinity, hence improving the film stretchability. Furthermore, the fully conjugated polymer back-bone allows maintenance of good charge carrier mobilities. Specifically, polymer PDPP-C4Ph (with C4Ph side groups) shows the highest mobility in the fully stretchable transistor and maintained its mobility even after being subjected to hundreds of stretching-releasing cycles at 25% strain. Altogether, the results provide anunderstanding of the use of asymmetrically substituted fused-ring conjugated polymer structures to tune mechanical and charge transport properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A hybrid cyt c maturation system enhances the bioelectrical performance of engineered Escherichia coli by improving the rate-limiting step

Bioelectronic devices can use electron flux to enable communication between biotic components and abiotic electrodes. We have modified Escherichia coli to electrically interact with electrodes by expressing the cytochrome c from Shewanella oneidensis MR-1. However, we observe inefficient electrical performance, which we hypothesize is due to the limited compatibility of the E. coli cytochrome c maturation (Ccm) systems with MR-1 cytochrome c. Here we test whether the bioelectronic performance of E. coli can be improved by constructing hybrid Ccm systems containing protein domains from both E. coli and S. oneidensis MR-1. The hybrid CcmH increased cytochrome c expression by increasing the abundance of CymA 60%, while only slightly changing the abundance of the other cytochromes c. Electrochemical measurements showed that the overall current from the hybrid ccm strain increased 121% relative to the wildtype ccm strain, with an electron flux per cell of 12.3 ± 0.3 fA·cell -1 . Additionally, the hybrid ccm strain doubled its electrical response with the addition of exogenous flavin, and quantitative analysis of this demonstrates CymA is the rate-limiting step in this electron conduit. These results demonstrate that this hybrid Ccm system can enhance the bioelectrical performance of the cyt c expressing E. coli, allowing the construction of more efficient bioelectronic devices.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Robustness of magnetocrystalline anisotropy and coercivity in Fe–Co–B

As a potential candidate for critical chemical element free permanent magnet, (Fe 0.7 Co 0.3 ) 2 B, shows promising intrinsic magnetic properties, including large magnetization, high Curie temperature and moderate magnetocrystalline anisotropy (MCA). Still, the coercivity that has been achieved is relatively low. To understand and improve coercivity, here we study the robustness of MCA related to the fluctuation of chemical composition and the structural distortion and its effect on coercivity in (Fe 0.7 Co 0.3 ) 2 B from first principles DFT (density functional theory) calculation and micromagnetic simulation. A fluctuation of cobalt content of 10%, or 1% isotropic lattice strain, or 2% tetragonal distortion reduces MCA energy up to 30%. By considering randomly distributed local MCA energy reduction up to 30%, the calculated coercivity of anisotropic bulk magnets reduced from 3.6 kOe to 2.2 kOe. Rational microstructure design, such as grain size refinement and development of strong crystal texture of MCA easy-axis (i.e., degree of alignment for (Fe 0.7 Co 0.3 ) 2 B grains), can enhance coercivity and mitigate the effect of local MCA reduction. In addition to acceptable intrinsic magnetic properties, the promising hard magnetic phase needs good MCA robustness to facilitate the development of practical magnets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Mechanistic Insights into Aldehyde Production from Electrochemical CO 2 Reduction on CuAg Alloy via Operando X-ray Measurements

CO 2 electrolysis converts the greenhouse gas CO 2 into valuable fuels and chemicals, such as carbon monoxide, ethylene, ethanol, etc. Currently, Cu is the only known monometallic catalyst capable of producing multicarbon products from electrochemical CO 2 reduction reaction (eCO2RR), while the poor selectivity limits its further use. It has been found that introducing Ag atoms into the Cu lattice can modulate product preference. However, the synergistic effects between Cu and Ag, and thus, the catalytic performance, are strongly influenced by catalyst morphology, electrolyzer configuration, reaction conditions, etc. Operando measurements can provide explicit information on the catalyst dynamic variation during the reaction, but their operation and analysis are challenging. Herein, we prepared CuAg multiphase alloy catalysts by magnetron sputtering, which allowed for investigating the intrinsic interaction between Cu and Ag. eCO2RR performance exhibited an improved selectivity toward carbonyls at the expense of hydrogen and hydrocarbons. The partially alloyed Cu and Ag phases were confirmed by operando X-ray diffraction. By means of combining operando X-ray measurements and density functional theory (DFT) calculations, the preferred carbonyl production is attributed to the reduced electron density and compressive strain of Cu due to Ag incorporation, which leads to a deeper d-band center and therefore weakened intermediate adsorption and oxophilicity. In conclusion, this work provides evidence of the intrinsic structural and electronic interaction between Cu and Ag during eCO2RR. The obtained information will facilitate the design of bi/multi-phase metallic or alloy electrocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

PACE: Producing Algae for Co-Products and Energy (Final Report)

The PACE (Producing Algae for Co-Products and Energy) consortium was comprised of scientists from national laboratories (Los Alamos National Laboratory, Pacific Northwest National Laboratory), research institutions (New Mexico Consortium), academic institutions (Arizona State University, Colorado School of Mines, Colorado State University, Washington State University) and private companies (Reliance Industries, PanPacific, Genifuel and Sonosop) dedicated to making process improvements in algal biotechnology, with an emphasis on renewable fuels and co-products from biomass. The scope of work was focused on improving algal cultivation and processing to achieve an overall energy return on investment (EROI) >3, a carbon index less than 55 grams carbon dioxide per megajoule (gCO2/MJ) and a nearly two-fold reduction in fuel cost to ≤$5 per gallon of gasoline equivalent (gge). The PACE project was originally focused on using two strains of Chlorella sorokiniana (Cs1412 and Cs1230), but later grew to encompass marine strains of Nannochloropsis and algal production strains from Reliance Industries Limited (RIL).

09 BIOMASS FUELS↗
DOE OSTI2020

Spatially resolved fibre cavity ring down spectroscopy

Abstract This paper presents a fibre cavity ring down spectroscopy probed by Rayleigh scattering optical frequency domain reflectometry (OFDR), which provides spatial location of stimuli and improved signal to noise ratio for distributed sensing measurements. A section of optical fibre was integrated into an active fibre ring cavity with optical gain and interrogated by the OFDR system for 11 cycles with a single laser scan. Through the cavity ring down configuration, root-mean-squared (RMS) noise of distributed temperature and strain measurements was reduced to 6.9 mK and less than 0.1 με, respectively for 1-cm spatially resolved measurements. Our work shows that the active fibre cavity configuration can be combined with distributed fibre sensing schemes to achieve both high spatial resolution and high sensitivity measurements.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Mechanical rolling and annealing of wire-arc additively manufactured stainless steel plates

Thin walls of 304L stainless steel were fabricated by wire-arc additive manufacturing (WAAM) followed by post build thermomechanical processing to modify the as built microstructure and properties. The walls were made using a high-deposition-rate robotically controlled gas-metal arc welding system and were characterized using optical microscopy and tensile tested for mechanical properties. Post processing consisted of mechanical rolling the walls to 25% and 40% strains, followed by annealing at 1050°C to demonstrate a wide range of properties. Results show that WAAM can be used to build custom sized semi-finished parts or blanks that can later be thermomechanically processed to increase strength and ductility through recrystallization of the as built microstructure, and/or processed into desired shapes with improved mechanical properties.

304L stainless steel↗
DOE OSTI2022

Evaluation of engineered low-lignin poplar for conversion into advanced bioproducts

Lignocellulosic resources are promising feedstocks for the manufacture of bio-based products and bioenergy. However, the inherent recalcitrance of biomass to conversion into simple sugars currently hinders the deployment of advanced bioproducts at large scale. Lignin is a primary contributor to biomass recalcitrance as it protects cell wall polysaccharides from degradation and can inhibit hydrolytic enzymes via non-productive adsorption. Several engineering strategies have been designed to reduce lignin or modify its monomeric composition. For example, expression of bacterial 3-dehydroshikimate dehydratase (QsuB) in poplar trees resulted in a reduction in lignin due to redirection of metabolic flux toward 3,4-dihydroxybenzoate at the expense of lignin. This reduction was accompanied with remarkable changes in the pools of aromatic compounds that accumulate in the biomass. The impact of these modifications on downstream biomass deconstruction and conversion into advanced bioproducts was evaluated in the current study. Using ionic liquid pretreatment followed by enzymatic saccharification, biomass from engineered trees released more glucose and xylose compared to wild-type control trees under optimum conditions. Fermentation of the resulting hydrolysates using Rhodosporidium toruloides strains engineered to produce α-bisabolene, epi-isozizaene, and fatty alcohols showed no negative impact on cell growth and yielded higher titers of bioproducts (as much as + 58%) in the case of QsuB transgenics trees. Our data show that low-recalcitrant poplar biomass obtained with the QsuB technology has the potential to improve the production of advanced bioproducts.

09 BIOMASS FUELS↗
DOE OSTI2026

All‐Solid‐State Batteries With Mechanically Stable Interfaces Consisting of a Zero‐Strain Cation‐Disordered Rocksalt Cathode

Interface stabilization is critical to the development of working all‐solid‐state batteries. Rigid cathode/solid electrolyte interfaces often disintegrate due to anisotropic volume change of cathode‐active materials, resulting in irreversible capacity loss. Herein, we demonstrate that Li 1.211 Mo 0.467 Cr 0.3 O 2 (LMCO), a pioneering cation‐disordered rocksalt oxide (DRX) cathode that has intrinsically small volume change upon lithium intercalation, can be integrated with a thiophosphate‐based solid electrolyte for all‐solid‐state batteries. Interface stability of the all‐solid LMCO cell was investigated by electrochemical impedance spectroscopy, X‐ray micro‐computed tomography, and electron microscopy. Since LMCO was initially synthesized as a layered phase exhibiting a large volume change, interface disintegration can be observable in the early cycles. As layered LMCO phase‐transformed into DRX LMCO in subsequent cycles, reintegration of the interfaces occurs within a pressurized cell as a result of its zero‐stain behavior. Consequently, the DRX LMCO cathode maintains interface integrity, and thus electrical wiring, over an extended number of cycles, leading to improved capacity retention with small internal cell resistance.

DRX↗
DOE OSTI2026

Nanoscale Compositional and Strain Gradients Enable High‐Speed and Amplitude‐Resolved Pyroelectric Sensing

The frequency response of pyroelectric sensors is fundamentally governed by thermal time constant (τth, determined by thermal mass and thermal conductance) and electrical impedance arising from film capacitance and readout circuit. Conventional bulk LiTaO3 detectors are optimized for high responsivity at low modulation frequencies (0.1-10 Hz), possessing a large τth that thermally averages rapid temperature oscillations at elevated modulation frequencies, limiting fidelity in resolving dynamic varying thermal signals. Here, compositional and strain gradients are introduced into 100-nm-thick relaxor-ferroelectric films reducing τth to ≈2 µs and producing built-in potentials (≈1.45 V or 145 kV cm-1) that enhance the pyroelectric coefficient and suppress the dielectric constant. This enables complementary dual-mode operation by enhancing current-mode electrical responsivity and improving the voltage-mode figure of merit - advantageous for superior temperature resolution (ΔTmin ≈ 30 µK). The responsivity peak shifts to near 1 kHz (>2500-times higher than conventional bulk sensors), with measurable responsivity extending to a carrier frequency of 100 kHz and amplitude-resolved detection at modulation frequencies up to 15 kHz. These results establish nanoscale internal-field engineering can reshape electro-thermal trade-off in pyroelectric thin films toward zero-bias, high-thermal-sensitivity, and amplitude-resolved thermal sensing across a wide frequency bandwidth.

Lin, Ching‐Che↗
DOE OSTI2022

Gate-tunable Veselago interference in a bipolar graphene microcavity

The relativistic charge carriers in monolayer graphene can be manipulated in manners akin to conventional optics. Klein tunneling and Veselago lensing have been previously demonstrated in ballistic graphene pn-junction devices, but collimation and focusing efficiency remains relatively low, preventing realization of advanced quantum devices and controlled quantum interference. Here, we present a graphene microcavity defined by carefully-engineered local strain and electrostatic fields. Electrons are manipulated to form an interference path inside the cavity at zero magnetic field via consecutive Veselago refractions. The observation of unique Veselago interference peaks via transport measurement and their magnetic field dependence agrees with the theoretical expectation. We further utilize Veselago interference to demonstrate localization of uncollimated electrons and thus improvement in collimation efficiency. Our work sheds new light on relativistic single-particle physics and provide a new device concept toward next-generation quantum devices based on manipulation of ballistic electron trajectory.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High-throughput phase-field simulations and machine learning of resistive switching in resistive random-access memory

Metal oxide-based Resistive Random-Access Memory (RRAM) exhibits multiple resistance states, arising from the activation/deactivation of a conductive filament (CF) inside a switching layer. Understanding CF formation kinetics is critical to achieving optimal functionality of RRAM. Here a phase-field model is developed, based on materials properties determined by ab initio calculations, to investigate the role of electrical bias, heat transport and defect-induced Vegard strain in the resistive switching behavior, using MO 2- x systems such as HfO 2- x as a prototypical model system. It successfully captures the CF formation and resultant bipolar resistive switching characteristics. High-throughput simulations are performed for RRAMs with different material parameters to establish a dataset, based on which a compressed-sensing machine learning is conducted to derive interpretable analytical models for device performance (current on/off ratio and switching time) metrics in terms of key material parameters (electrical and thermal conductivities, Vegard strain coefficients). These analytical models reveal that optimal performance (i.e., high current on/off ratio and low switching time) can be achieved in materials with a low Lorenz number, a fundamental material constant. This work provides a fundamental understanding to the resistive switching in RRAM and demonstrates a computational data-driven methodology of materials selection for improved RRAM performance, which can also be applied to other electro-thermo-mechanical systems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Deep learning of structural morphology imaged by scanning X-ray diffraction microscopy

Scanning X-ray nanodiffraction microscopy is a powerful technique for spatially resolving nanoscale structural morphologies by diffraction contrast. One of the critical challenges in experimental nanodiffraction data analysis is posed by the convergence angle of nanoscale focusing optics which creates simultaneous dependency of the far-field scattering data on three independent components of the local strain tensor-corresponding to dilation and two potential rigid body rotations of the unit cell. All three components are in principle resolvable through a spatially mapped sample tilt series; however, traditional data analysis is computationally expensive and prone to artifacts. In this study, we implement NanobeamNN, a convolutional neural network specifically tailored to the analysis of scanning probe X-ray microscopy data. NanobeamNN learns lattice strain and rotation angles from simulated diffraction of a focused X-ray nanobeam by an epitaxial thin film and can directly make reasonable predictions on experimental data without the need for additional fine-tuning. We demonstrate that this approach represents a significant advancement in computational speed over conventional methods, as well as a potential improvement in accuracy over the current standard.

Luo, Aileen [Cornell Univ., Ithaca, NY (United Sta↗
DOE OSTI2022

Phylogenetic analyses and reclassification of the oleaginous marine species Nannochloris sp. “desiccata" (Trebouxiophyceae, Chlorophyta), formerly Chlorella desiccata , supported by a high-quality genome assembly

Microalgae are diverse, with many gaps remaining in phylogenetic and physiological understanding. Thus, studying new microalgae species increases our broader comprehension of biological diversity, and evaluation of new candidates as algal production platforms can lead to improved productivity under a variety of cultivation conditions. Chlorella is a genus of fast-growing species often isolated from freshwater habitats and cultivated as a source of nutritional supplements. However, the use of freshwater increases competition with other freshwater needs. We identified Chlorella desiccata to be worthy of further investigation as a potential algae production strain, due to its isolation from a marine environment and its promising growth and biochemical composition properties. Long-read genomic sequencing was conducted for C. desiccata UTEX 2526, resulting in a high-quality, near chromosome level, diploid genome with an assembly length of 21.55 Mbp in only 18 contigs. We also report complete circular mitochondrial and chloroplast genomes. Phylogenomic and phylogenetic analyses using nuclear, chloroplast, 18S rRNA, and actin sequences revealed that this species clades within strains currently identified as Nannochloris (Trebouxiophyceae, Chlorophyta), leading to its reclassification as Nannochloris sp. “desiccata” UTEX 2526. The mode of cell division for this species is autosporulation, differing from the type species N. bacillaris. As has occurred across multiple microalgae genera, there are repeated examples of Nannochloris species reclassification in the literature. This high-quality genome assembly and phylogenetic analysis of the potential algal production strain Nannochloris sp. “desiccata” UTEX 2526 provides an important reference and useful tool for further studying this region of the phylogenetic tree.

59 BASIC BIOLOGICAL SCIENCES↗