Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Single Crystal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Bulk and surface characterization of In2O3(001) single crystal

A comprehensive bulk and surface investigation of high-quality In2O3(001) single crystals is reported. The transparent-yellow, cube-shaped single crystals were grown using the flux method. ICP-MS measurements reveal small residues of Pb, Mg and Pt in the crystals. Four-point-probe measurements show a resistivity of 2 0.5 105 cm, which translates into a carrier concentration of 1012 cm-3. The results from X-ray diffraction (XRD) measurements revise the lattice constant to 10.1150(5) from the previously accepted value of 10.117 . Scanning Tunneling Microscopy (STM) images of a reduced (sputtered/annealed) surface show a step height of 5 , which indicates a preference for one type of surface termination. A combination of low-energy ion scattering (LEIS) and atomically resolved STM indicates an indium-terminated surface with small islands of 2.5 height, which corresponds to a strongly distorted indium lattice. Scanning Tunneling Spectroscopy (STS) reveals a pronounced surface state at the Fermi Level (EF). Photoelectron Spectroscopy (PES) shows additional, deep-lying band gap states, which can be removed by exposure of the surface to activated oxygen. Oxidation also results in a shoulder at the O 1s core level at a higher binding energy, possibly indicative of a surface peroxide species. A downward band bending of 0.4 eV and an upward band bending of ~0.1 eV is observed for the reduced and oxidized surfaces, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Single-crystal X-ray diffraction on the structure of (Al,Fe)-bearing bridgmanite in the lower mantle

Abstract Here we have performed single-crystal X-ray diffraction (SCXRD) experiments on two high-quality crystal platelets of (Al,Fe)-bearing bridgmanite (Mg0.88Fe0.0653+Fe0.0352+Al0.03)(Al0.11Si0.90)O3 (Fe10-Al14-Bgm) up to 64.6(6) GPa at room temperature in a Boehler-Almax type diamond-anvil cell. Refinements on the collected SCXRD patterns reveal reliable structural information of single-crystal Fe10-Al14-Bgm, including unit-cell parameters, atomic coordinates, and anisotropic displacement parameters. Together with Mössbauer and electron microprobe analyses, our best single-crystal refinement model indicates that the sample contains ~6.5 mol% Fe3+, 3.5 mol% Fe2+, and 3 mol% Al3+ in the large pseudo-dodecahedral site (A site), and ~11 mol% Al3+ in the small octahedral site (B site). This may indicate that Al3+ in bridgmanite preferentially occupies the B site. Our results show that the compression of Fe10-Al14-Bgm with pressure causes monotonical decreases in the volumes of AO12 pseudo-dodecahedron and BO6 octahedron (VA and VB, respectively) as well as the associated A-O and B-O bond lengths. The interatomic angles of B-O1-B and B-O2-B decrease from 145.2–145.8° at 4.2(1) GPa to 143.3–143.5° at 64.6(6) GPa. Quantitative calculations of octahedral tilting angles (Ф) show that Ф increases smoothly with pressure. We found a linear relationship between the polyhedral volume ratio and the Ф in the bridgmanite with different compositions: VA/VB = –0.049Φ + 5.549. Our results indicate an increased distortion of the Fe10-Al14-Bgm structure with pressure, which might be related to the distortion of A-site Fe2+. The local environmental changes of A-site Fe2+ in bridgmanite could explain previous results on the hyperfine parameters, abnormal lattice thermal conductivity, mean force constant of iron bonds and other physical properties, which in turn provide insights into our understanding on the geophysics and geochemistry of the planet.

Geochemistry & Geophysics↗

High-pressure behavior of bromine confined in the one-dimensional channels of zeolite AlPO 4 -5 single crystals

We present a joint experimental and theoretical study on the high-pressure behavior of bromine confined in the one-dimensional (1D) nanochannels of zeolite AlPO 4 -5 (AFI) single crystals. Raman scattering experiments indicate that loading bromine into AFI single crystals can lead to the formation of bromine molecular chains inside the nanochannels of the crystals. High-pressure Raman and X-ray diffraction studies demonstrate that high pressure can increase the length of the confined bromine molecular chains and modify the inter- and intramolecular interactions of the molecules. We report the confined bromine shows a considerably different high-pressure behavior to that of bulk bromine. The pressure-elongated bromine molecular chains can be preserved when the pressure is reduced to ambient pressure. Theoretical simulations explain the experimental results obtained from the Raman spectroscopy and X-ray diffraction studies. Furthermore, we find that the intermolecular distance between confined bromine molecules gradually becomes comparable to the intramolecular bond length in bromine molecules upon compression. This may result in the dissociation of the bromine molecules and the formation of 1D bromine atomic chains at pressures above 24 GPa. Our study suggests that the unique nanoconfinement has a considerable effect on the high-pressure behavior of bromine, and the confined bromine species concomitantly enhance the structural stability of the host AFI single crystals.

36 MATERIALS SCIENCE↗

Bridgman Growth of Large SrI2:Eu2+ Single Crystals: A High-performance Scintillator for Radiation Detection Applications

Single-crystal strontium iodide (SrI2) doped with relatively high levels (e.g., 3 - 6 %) of Eu2+ exhibits characteristics that make this material superior, in a number of respects, to other scintillators that are currently used for radiation detection. Specifically, SrI2:Eu2+ has a light yield that is significantly higher than LaBr3:Ce3+ -a currently employed commercial high-performance scintillator. Additionally, SrI2:Eu2+ is characterized by an energy resolution as high as 2.6% at the 137Cs gamma-ray energy of 662 keV, and there is no radioactive component in SrI2:Eu2+ - unlike LaBr3:Ce3+ that contains 138La. The Ce3+-doped LaBr3 decay time is, however, faster (30 nsec) than the 1.2 sec decay time of SrI2:Eu2+. Due to the relatively low melting point of strontium iodide (~515 oC), crystal growth can be carried out in quartz crucibles by the vertical Bridgman technique. Materials-processing and crystal-growth techniques that are specific to the Bridgman growth of europium-doped strontium iodide scintillators are described here. These techniques include the use of a porous quartz frit to physically filter the molten salt from a quartz antechamber into the Bridgman growth crucible and the use of a bent or bulb grain selector design to suppress multiple grain growth. Single crystals of SrI2:Eu2+ scintillators with good optical quality and scintillation characteristics have been grown in sizes up to 5.0 cm in diameter by applying these techniques. Other aspects of the SrI2:Eu2+ crystal-growth methods and of the still unresolved crystal-growth issues are described here.

Boatner, Lynn A↗

Chemical decomposition in shock-compressed 1,1-diamino-2,2-dinitroethene (FOX-7) single crystals: Time-resolved Raman spectroscopy

Understanding the evolution of chemical decomposition—at the molecular level—in shock-compressed insensitive high explosive (IHE) single crystals is an important need. Toward this goal, time-resolved Raman spectra were measured in 1,1-diamino-2,2-dinitroethene (FOX-7) single crystals shock compressed to stresses above 20 GPa. At 22 GPa and higher stresses, the Raman peak intensities were significantly reduced, showing the onset and extent of chemical changes. At 33 GPa, no Raman peaks were observed, suggesting complete decomposition of FOX-7. The 22 GPa onset from Raman data is in marked contrast to the much higher (32 GPa) onset determined previously from wave profile measurements—showing the significantly greater sensitivity of Raman measurements for gaining insight into shock-induced molecular-level changes in IHE single crystals. The close match between the complete loss of Raman peaks at 33 GPa and the 32 GPa reaction threshold determined from continuum data makes a good case that the two results are related and they reflect significant energy release due to decomposition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of structural defects on the magnetic properties of the EuBaCo{sub 1.90}O{sub 5.36} single crystal

The effect of structural defects in cobalt and oxygen sublattices with the constant average oxidation level 3+ of all cobalt ions on the magnetic properties of the EuBaCo{sub 1.90}O{sub 5.36} single crystal has been studied. The magnetic properties of the single crystal and the polycrystalline sample of the corresponding composition are compared in the range T = 200–650 K. The results show that the cobalt-deficient EuBaCo{sub 2–x}O{sub 5.5–δ} samples demonstrate a three-dimensional XY ferromagnetic ordering of magnetic sublattices. The values of the effective magnetic moment at T > 480 K indicate the existence of the IS and HS states of Co{sup 3+} ions. The large difference of values of μ{sub eff} of the EuBaCo{sub 1.90}O{sub 5.36} single crystal and polycrystal can be due to that the magnetic ion spins lie in plane ab. The magnetic field directed along plane ab substantially influences the magnetic ordering at T < 300 K.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fabrication and characterization of electrospun single-crystal lead manganese borate nanofibers

Highlights: • Single crystal PbMnBO4 nanofibers were successfully fabricated by electrospinning process. • The PbMnBO4 nanofibers synthesized for the first time and unprecedented in the literature. • Characterization of PbMnBO{sub 4} nanofibers in mineralogical, optical and thermal properties was revealed. • The nanofibers exhibit single crystalline features with an average size between 120 and 250 nm. • These nanofibers can be used in optic or photonic fields as a flexible sensor due to its nonlinear and ferromagnetic properties. - Abstract: Anhydrous borate compounds are important materials in optical applications as nonlinear optical materials (NLO), due to the presence of structural B{sub x}O{sub y} subunits. Herein, lead manganese borate (PbMnBO{sub 4}) nanofibers have been firstly fabricated via a facile approach using a simple and inexpensive electrospinning technique. All of the synthesized samples were analyzed with X-Ray Diffractometer (XRD), Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Fourier Transform Infrared (FTIR), and Ultraviolet-visible Spectroscopy (UV–vis) method. In addition, they were thermally analyzed with Thermal Gravimetric and Differential Thermal Analyzer and TG-DTA diagrams were discussed in detail. All of the characterization results showed that the obtained PbMnBO{sub 4} nanostructures have nanofiber structures and good crystalline features. PbMnBO{sub 4} nanofiber synthesized for the first time and unprecedented in the literature is promising absorber materials for nonlinear optic applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ames Lab 101: Single Crystal Growth

Ames Laboratory scientist Deborah Schlagel talks about the Lab's research in growing single crystals of various metals and alloys. The single crystal samples are vital to researchers' understanding of the characteristics of a materials and what gives these materials their particular properties.

36 MATERIALS SCIENCE↗

Effects of Microstructural Parameters on Creep of Nickel-Base Superalloy Single Crystals

Microstructure-sensitive creep models have been developed for Ni-base superalloy single crystals. Creep rupture testing was conducted on fourteen single crystal alloys at two applied stress levels at each of two temperatures, 982 and 1093 C. The variation in creep lives among the different alloys could be explained with regression models containing relatively few microstructural parameters. At 982 C, gamma-gamma prime lattice mismatch, gamma prime volume fraction, and initial gamma prime size were statistically significant in explaining the creep rupture lives. At 1093 C, only lattice mismatch and gamma prime volume fraction were significant. These models could explain from 84 to 94 percent of the variation in creep lives, depending on test condition. Longer creep lives were associated with alloys having more negative lattice mismatch, lower gamma prime volume fractions, and finer gamma prime sizes. The gamma-gamma prime lattice mismatch exhibited the strongest influence of all the microstructural parameters at both temperatures. Although a majority of the alloys in this study were stable with respect to topologically close packed (TCP) phases, it appeared that up to approximately 2 vol% TCP phase did not affect the 1093 C creep lives under applied stresses that produced lives of approximately 200 to 300 h. In contrast, TCP phase contents of approximately 2 vol% were detrimental at lower applied stresses where creep lives were longer. A regression model was also developed for the as-heat treated initial gamma prime size; this model showed that gamma prime solvus temperature, gamma-gamma prime lattice mismatch, and bulk Re content were all statistically significant.

MacKay, Rebecca A.↗

First Single-Crystal Mullite Fibers

Ceramic-matrix composites strengthened by suitable fiber additions are being developed for high-temperature use, particularly for aerospace applications. New oxide-based fibers, such as mullite, are particularly desirable because of their resistance to high-temperature oxidative environments. Mullite is a candidate material in both fiber and matrix form. The primary objective of this work was to determine the growth characteristics of single-crystal mullite fibers produced by the laser-heated floating zone method. Directionally solidified fibers with nominal mullite compositions of 3Al2O3 2SiO2 were grown by the laser-heated floating zone method at the NASA Lewis Research Center. SEM analysis revealed that the single-crystal fibers grown in this study were strongly faceted and that the facets act as critical flaws, limiting fiber strength. The average fiber tensile strength is 1.15 GPa at room temperature. The mullite fibers exhibit superior strength retention (80 percent of their room temperature tensile strength at 1450 C). Examined by transmission electron microscopy, these mullite single crystals are free of dislocations, low-angle boundaries, and voids. In addition, they show a high degree of oxygen vacancy ordering. High-resolution digital images from an optical microscope furnish evidence of the formation of a liquid-liquid miscibility gap during crystal growth. These images represent the first experimental evidence of liquid immiscibility for these compositions and temperatures. Continuing investigation with controlled seeding of mullite single crystals is planned.

Source record↗

Nanosecond X-ray detector based on high resistivity ZnO single crystal semiconductor

The pulse radiation detectors are sorely needed in the fields of nuclear reaction monitoring, material analysis, astronomy study, spacecraft navigation, and space communication. In this work, we demonstrate a nanosecond X-ray detector based on ZnO single crystal semiconductor, which emerges as a promising compound-semiconductor radiation detection material for its high radiation tolerance and advanced large-size bulk crystal growth technique. The resistivity of the ZnO single crystal is as high as 10{sup 13} Ω cm due to the compensation of the donor defects (V{sub O}) and acceptor defects (V{sub Zn} and O{sub i}) after high temperature annealing in oxygen. The photoconductive X-ray detector was fabricated using the high resistivity ZnO single crystal. The rise time and fall time of the detector to a 10 ps pulse electron beam are 0.8 ns and 3.3 ns, respectively, indicating great potential for ultrafast X-ray detection applications.

36 MATERIALS SCIENCE↗

Heat capacity, resistivity, and angular dependent magnetization studies of single crystal Nd 1 + ϵ Fe 4 B 4 for ϵ ≈ 1 7

Advances in crystal growth have allowed for synthesis of large single crystals of Nd 1+ϵ Fe 4 B 4 , a well-known phase with a modulated structure. As a result we are able to report heat capacity and resistivity measurements on a single crystal Nd 1+ϵ Fe 4 B 4 sample with a distribution of ϵ that skews towards the solubility limit of Nd near ϵ ≈ 17. Heat capacity measurements show evidence of crystal field splitting at temperatures higher than the long-range ferromagnetic Curie temperature. Heat capacity, resistivity, and magnetization measurements all confirm a Curie temperature of 7 K which is lower than previously reported values in the Nd 1+ϵ Fe 4 B 4 system. Here, we also perform measurements of the angular dependence of the magnetization and discover behavior associated with the magnetic anisotropy that is inconsistent with the simple description previously proposed.

36 MATERIALS SCIENCE↗

Resolution of the discrepancy between the variation of the physical properties of Ce 1- x Yb x CoIn 5 single crystals and thin films with Yb composition

The extraordinary electronic phenomena including an Yb valence transition, a change in Fermi surface topology, and suppression of the heavy fermion quantum critical field at a nominal concentration x≈0.2 have been found in the Ce 1- x Yb x CoIn 5 system. These phenomena have no discernable effect on the unconventional superconductivity and normal-state non-Fermi liquid behaviour that occur over a broad range of x up to ~0.8. However, the variation of the coherence temperature T* and the superconducting critical temperature T c with nominal Yb concentration x for bulk single crystals is much weaker than that of thin films. To determine whether differences in the actual Yb concentration of bulk single crystals and thin film samples might be responsible for these discrepancies, we employed Vegard’s law and the spectroscopically determined values of the valences of Ce and Yb as a function of x to determine the actual composition x act of bulk single crystals. This analysis is supported by energy-dispersive X-ray spectroscopy, wavelength-dispersive X-ray spectroscopy, and transmission X-ray absorption edge spectroscopy measurements. The actual composition x act is found to be about one-third of the nominal concentration x up to x~0.5, and resolves the discrepancy between the variation of the physical properties of Ce 1- x Yb x CoIn 5 single crystals and thin films with Yb concentration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A low-temperature sample orienting device for single crystal spectroscopy at the SNS

A low temperature sample orientation device providing three axes of rotation has been successfully built and is in testing for use on several spectrometers at the spallation neutron source (SNS). Sample rotation about the vertical ({omega}) axis of nearly 360{sup o} and out of plane tilts ({phi} and {nu}) of from -3.4{sup o} to 4.4{sup o} and from -2.8{sup o} to 3.5{sup o}, respectively, are possible. An off-the-shelf closed cycle refrigerator (CCR) is mounted on a room temperature sealed rotary flange providing {omega} rotations of the sample. Out-of-plane tilts are made possible by piezoelectric actuated angular positioning devices mounted on the low temperature head of the CCR. Novel encoding devices based on magnetoresistive sensors have been developed to measure the tilt stage angles. This combination facilitates single crystal investigations from room temperature to 3.1 K. Commissioning experiments of the rotating CCR for both powder and single crystal samples have been performed on the ARCS spectrometer at the SNS. For the powder sample this device was used to continuously rotate the sample and thus average out any partial orientation of the powder. The powder rings observed in S(Q) are presented. For the single crystal sample, the rotation was used to probe different regions of momentum transfer (Q-space). Laue patterns obtained from a single crystal sample at two rotation angles are presented.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Operando single crystal neutron diffraction reveals insight into the field response mechanisms in the hydrogen-bonded KH 2 PO 4 ferroelectric

The mechanism that facilitates polarization reorientation in KH 2 PO 4 (KDP) was investigated using operando single-crystal neutron diffraction. Diffraction data were measured from a KDP single crystal during the application of alternating electric fields and were then binned into 40 increments to enable field-dependent single-crystal structure refinements. The field-dependent structures are compared with an as-grown crystal to determine how the lattice and atomic sites evolve in response to the applied electric fields. These analyses provide evidence that the reorientation of the macroscopic polarization is facilitated through a cooperative change in hydrogen bonding, which results in the reversal of the spontaneous dipole. In addition, a decrease in secondary extinction near the coercive field indicates that the inversion of the macroscopic polarization is achieved through the nucleation and subsequent growth of new domains.

36 MATERIALS SCIENCE↗

Bulk growth of <001> organic nonlinear optical (NLO) L-arginine 4-nitrophenolate 4-nitrophenol dihydrate (LAPP) single crystals by SR method

A transparent uniaxial L-arginine 4-nitrophenolate 4-nitrophenol dehydrate (LAPP) single crystal having dimension of 20 mm diameter and 45 mm length was grown by Sankaranarayanan-Ramasamy (SR) method with a growth rate of 1 mm per day. Using an identical solution the conventional crystal grown to a dimension of 8×5×5 mm{sup 3} was obtained over a period of 30 days. The crystal structure has been confirmed by single crystal X-ray diffraction measurement. The crystalline perfection of LAPP crystals grown by slow evaporation solution technique (SEST) and SR method were characterized using Vickers microhardness, UV-Vis NIR, chemical etching, dark and photo current measurements. The above study indicates that the crystal quality of the Sankaranarayanan-Ramasamy (SR) method grown LAPP is good compared to the conventional method grown crystal.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of loading orientations on the microstructure and property of Al−Cu single crystal during stress aging

The precipitation behavior and property of Al−Cu alloy during stress aging under various loading orientations were investigated using single crystals. The resulting microstructures and the strength property were examined by transmission electron microscope (TEM) and compression test, respectively, and the effect of the distribution of θ′-plates on strength property were discussed. The results show that the precipitation distribution of θ′ was significantly affected by the loading orientation during stress aging of Al−Cu single crystals. Loading along close to 〈011〉{sub Al} directions provided more uniform precipitation distribution of θ′ as compared to loading along close to 〈001〉{sub Al} directions, and therefore provided higher strengthening stress of the θ′-plates for the stress aging sample. The results suggested that regulating the distribution of θ′ and therefore improving strength property are possible via controlling the loading orientation during stress aging. - Highlights: • We studied the effect of loading directions on stress aging of Al−Cu single crystal. • Precipitation distribution of θ′ was noticeably affected by the loading direction. • Loading along close to 〈011〉{sub Al} directions reduced the stress-orienting effect. • The strength property is closely related to the precipitation distribution of θ′. • It is possible to regulate the distribution of θ′ and improve strength property.

36 MATERIALS SCIENCE↗