SEARCH · Engineering Papers

Results for “Simplified Simulator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

All sources NASA NTRS DOE OSTI

NASA NTRS1994

Attitude stability of a spinning spacecraft during appendage deployment/retraction

The work presented is motivated by the need for a national satellite rescue policy, not the ad hoc policy now in place. In studying different approaches for a national policy, the issue of capture and stabilization of a tumbling spacecraft must be addressed. For a rescue mission involving a tumbling spacecraft, it may be advantageous to have a rescue vehicle which is compact and 'rigid' during the rendezvous/capture phase. After capture, passive stabilization techniques could be utilized as an efficient means of detumbling the resulting system (i.e., both the rescue vehicle and captures spacecraft). Since the rescue vehicle is initially compact and 'rigid,' significant passive stabilization through energy dissipation can only be achieved through the deployment of flexible appendages. Once stabilization is accomplished, retraction of the appendages before maneuvering the system to its final destination may also prove advantageous. It is therefore of paramount interest that we study the effect of appendage deployment/retraction on the attitude stability of a spacecraft. Particular interest should be paid to appendage retraction, since if this process is destabilizing, passive stabilization as proposed may not be useful. Over the past three decades, it has been an 'on-again-off-again affair' with the problem of spacecraft appendage deployment. In most instances, these studies have been numerical simulations of specific spacecraft configurations for which there were specific concerns. The primary focus of these studies was the behavior of the appendage during deployment; the effects of appendage retraction was considered only in one of these studies. What is missing in the literature is a thorough study of the effects of appendage deployment/retraction on the attitude stability of a spacecraft. This paper presents a rigorous analysis of the stability of a spinning spacecraft during the deployment or the retraction of an appendage. The analysis is simplified such that meaningful insights into the problem can be inferred; it is not overly simplified such that critical dynamical behavior is neglected. The system is analyzed assuming that the spacecraft hub is rigid. The appendage deployment mechanism is modeled as a point mass on a massless rod whose length undergoes prescribed changes. Simplified flexibility effects of the appendage are included. The system is examined for stability by linearizing the equations in terms of small deviations from steady, noninterfering coning motion. Routh's procedure for analyzing small deviations from steady motion in dynamical systems is utilized in the analysis. The system of equations are nondimensionalized to facilitate parametric studies. The results are presented in terms of a reduced number of nondimensional parameters so that some general conclusions may be drawn. Verification of the linear analysis is presented through numerical simulations of the complete nonlinear, nonautonomous, coupled equations.

Fitz-Coy, Norman↗

NASA NTRS2004

Aeroacoustic Analysis of a Simplified Landing Gear

A hybrid approach is used to investigate the noise generated by a simplified landing gear without small scale parts such as hydraulic lines and fasteners. The Ffowcs Williams and Hawkings equation is used to predict the noise at far-field observer locations from flow data provided by an unsteady computational fluid dynamics calculation. A simulation with 13 million grid points has been completed, and comparisons are made between calculations with different turbulence models. Results indicate that the turbulence model has a profound effect on the levels and character of the unsteadiness. Flow data on solid surfaces and a set of permeable surfaces surrounding the gear have been collected. Noise predictions using the porous surfaces appear to be contaminated by errors caused by large wake fluctuations passing through the surfaces. However, comparisons between predictions using the solid surfaces with the near-field CFD solution are in good agreement giving confidence in the far-field results.

Lockard, David P.↗

NASA NTRS2007

Slip Validation and Prediction for Mars Exploration Rovers

This paper presents a novel technique to validate and predict the rover slips on Martian surface for NASA's Mars Exploration Rovers. Different from the traditional approach, the proposed method uses the actual velocity profile of the wheels and the digital elevation map (DEM) from the stereo images of the terrain to formulate simplified equations of motion of the rovers. A weighted factor to the wheel-ground speed from the empirical data comprises the velocity equations of the simplified differential-algebraic system of the rover motion. Applying the discretization operator to these equations, the full kinematics state of the rover is then resolved by the configuration kinematics solution in the Robot Sequencing and Visualization Program (RSVP). This method produced accurate simulation of the rover movements compared with these of the earth testing vehicle. Using the telemetry from the onboard Visual Odometry, the simulated rover path also compares well with the actual track of the vehicle. Preliminary results indicated that the proposed computational method is very effective in planning the path of the rovers on the high-slope areas.

Mars Rovers↗

NASA NTRS1976

Noise measurements in a free-jet, flight simulation facility - Shear layer refraction and facility-to-flight corrections

The conversion of free-jet facility into equivalent flyover results is discussed. The essential problem is to 'calibrate out' the acoustic influence of the outer free-jet shear layer on the measurement, since this is absent in the flight case. Results are presented which illustrate the differences between current simplified models (vortex-sheet and geometric acoustics), and a more complete model based on the Lilley equation. Finally, the use of geometric acoustics for facility-to-flight data conversion is discussed.

Morfey, C. L.↗

NASA NTRS1994

Brief Communication: A Simplified Approach to Transient Convective Droplet Evaporation and Burning

Empirical correlations for evaporation rates from single fuel droplets have existed since the 1930s. These correlations, which will be referred to in this article as Froessling/Ranz-Marshall types of correlations, are appropriate to the special cases of steady-state evaporation in the absence of chemical reaction. In a previous article by the authors, the quasi-steady evaporation and burning processes associated with a fuel drop in a convective environment are examined through a droplet model based on the boundary layer approach. For droplet Reynolds numbers of practical interest, this model produces very reasonable steady state as well as quasi-time-dependent droplet simulations, requiring relatively short computational times and yielding good agreement with the above-mentioned empirical correlations. The steady-state case, however, is usually relevant to practical combustor situations only when the drop has reached a nearly uniform temperature since the heating process of the drop cannot be considered to be quasi-steady. In the present study, the transient heating process of the droplet interior during evaporation and/or burning is taken into account, and thus calculations pertaining to the entire life-time of the droplet are carried out. It is of particular interest here to obtain simplified correlations to describe the transient behavior of evaporating and burning droplets; these may be incorporated with greater ease into spray calculations. Accordingly, we have chosen to use stagnation conditions in the present model in a modification of the Froessling/Ranz-Marshall correlations. These modified correlations, incorporating an effective transfer number, produce a fairly accurate representation of droplet evaporation and burning, while requiring only one tenth the computational effort used in a full boundary layer solution.

Madooglu, K.↗

NASA NTRS1984

Externally driven magnetic reconnection

A model is presented in which externaly driven reconnection is simulated by solving the MHD equations in an initially plane current sheet. Magnetic reconnection in the earth's magnetotail is widely believed to be the direct cause of magnetospheric substorms. Both 2-D and 3-D versions of the model have been developed. It is postulated that connection in the tail is triggered by a local compression of the plasma sheet which results from an invasion of the solar wind into the magnetotail. Thus, the simulation is started by introducing flow from the lobes normal to the plasma sheet. When resistivity is generated in a local region of the neutral sheet, reconnection develops and magnetic energy is converted into plasma bulk flow. Although the driven reconnection model is highly simplified, it can aid in understanding many features of substorms in the tail; in particular, results show that rapid flows both earthward and tailward of the neutral line and the nightside substorm current system are natural consequences of driven magnetic reconnection.

Walker, R. J.↗

NASA NTRS1984

Concepts and algorithms for terminal-area traffic management

The nation's air-traffic-control system is the subject of an extensive modernization program, including the planned introduction of advanced automation techniques. This paper gives an overview of a concept for automating terminal-area traffic management. Four-dimensional (4D) guidance techniques, which play an essential role in the automated system, are reviewed. One technique, intended for on-board computer implementation, is based on application of optimal control theory. The second technique is a simplified approach to 4D guidance intended for ground computer implementation. It generates advisory messages to help the controller maintain scheduled landing times of aircraft not equipped with on-board 4D guidance systems. An operational system for the second technique, recently evaluated in a simulation, is also described.

Erzberger, H.↗

NASA NTRS1992

Mini-mast CSI testbed user's guide

The Mini-Mast testbed is a 20 m generic truss highly representative of future deployable trusses for space applications. It is fully instrumented for system identification and active vibrations control experiments and is used as a ground testbed at NASA-Langley. The facility has actuators and feedback sensors linked via fiber optic cables to the Advanced Real Time Simulation (ARTS) system, where user defined control laws are incorporated into generic controls software. The object of the facility is to conduct comprehensive active vibration control experiments on a dynamically realistic large space structure. A primary goal is to understand the practical effects of simplifying theoretical assumptions. This User's Guide describes the hardware and its primary components, the dynamic characteristics of the test article, the control law implementation process, and the necessary safeguards employed to protect the test article. Suggestions for a strawman controls experiment are also included.

Tanner, Sharon E.↗

NASA NTRS1984

Rapid torque-bounded line-of-sight pointing of SCOLE with a designer's choice of initial alignment

Researchers simplified the analytical expression of the line of sight (LOS) error, discovered and proved the independence of Euler angle Psi, calculated attitude angles corresponding to 0 degrees and 20 degrees LOS errors, determined choices of initial alignment, tailored the slew maneuvers for LOS pointing, simulated numerically the LOS pointing slew of the Spacecraft Control Laboratory Experiment (SCOLE), and evaluated the pointing performance.

Lin, Jiguan Gene↗

NASA NTRS1993

Erosive burning of solid propellants

Presented here is a review of the experimental and modeling work concerning erosive burning of solid propellants (augmentation of burning rate by flow of product gases across a burning surface). A brief introduction describes the motor design problems caused by this phenomenon, particularly for low port/throat area ratio motors and nozzleless motors. Various experimental techniques for measuring crossflow sensitivity of solid propellant burning rates are described, with the conclusion that accurate simulation of the flow, including upstream flow development, in actual motors is important since the degree of erosive burning depends not only on local mean crossflow velocity and propellant nature, but also upon this upstream development. In the modeling area, a brief review of simplified models and correlating equations is presented, followed by a description of more complex numerical analysis models. Both composite and double-base propellant models are reviewed. A second generation composite model is shown to give good agreement with data obtained in a series of tests in which composite propellant composition and heterogeneity (particle size distribution) were systematically varied. Finally, the use of numerical models for the development of erosive burning correlations is described, and a brief discussion of scaling is presented.

King, Merrill K.↗

NASA NTRS2002

Data Analysis for the SOLIS Vector Spectromagnetograph

The National Solar Observatory's SOLIS Vector Spectromagnetograph (VSM), which will produce three or more full-disk maps of the Sun's photospheric vector magnetic field every day for at least one solar magnetic cycle, is in the final stages of assembly. Initial observations, including cross-calibration with the current NASA/NSO spectromagnetograph (SPM) will soon be carried out at a test site in Tucson. This paper discusses data analysis techniques for reducing the raw data, calculation of line-of-sight magnetograms and both quick-look and high-precision inference of vector fields from Stokes spectral profiles. Existing SPM algorithms, suitably modified to accomodate the cameras, scanning pattern, and polarization calibration optics for the VSM, will be used to "clean" the raw data and to process line-of-sight, magnetograms. A recent. version of the High Altitude Observatory Milne-Eddington (HAO-ME) inversion code (Skumanich and Lites; 1987, 11)J 322, p. 473) will he used for high-precision vector fields since the algorithm has been extensively tested, is well understood, and is fast enough to complete data analysis within 24 hours of data acquisition. The simplified inversion algorithm of Auer, Heasley. arid House (1977, Sol. Phys. 55, p. 47) forms the initial guess for this version of the HAO-ME code and will be used for quick-look vector analysis of VSM data since its performance on simulated Stokes profiles is better than other candidate methods. Improvements (e.g., principal components analysis or neural networks) are under consideration and will be straightforward to implement. However, current resources are sufficient to store the original Stokes profiles only long enough for high-precision analysis. Retrospective reduction of Stokes data with improved methods will not be possible, and modifications will only be introduced when the advantages of doing so are compelling enough to justify discontinuity in the long-term data stream.

Jones, Harrison P.↗

NASA NTRS2004

An Overview of Recent Developments in Computational Aeroelasticity

The motivation for Computational Aeroelasticity (CA) and the elements of one type of the analysis or simulation process are briefly reviewed. The need for streamlining and improving the overall process to reduce elapsed time and improve overall accuracy is discussed. Further effort is needed to establish the credibility of the methodology, obtain experience, and to incorporate the experience base to simplify the method for future use. Experience with the application of a variety of Computational Aeroelasticity programs is summarized for the transonic flutter of two wings, the AGARD 445.6 wing and a typical business jet wing. There is a compelling need for a broad range of additional flutter test cases for further comparisons. Some existing data sets that may offer CA challenges are presented.

Bennett, Robert M.↗

NASA NTRS2006

Cassini-Huygens Aerodynamics with Comparison to Flight

An analysis has been performed on the aerodynamics of the Cassini spacecraft as it passed through the atmosphere of Titan with and without the Huygens probe attached. The free stream density of Titan s atmosphere was measured by two methods. However, these methods resulted in very different values of density, one result being 3-5 times higher than the other. In an attempt to understand the source of this discrepancy and verify the assumptions made by and the original engineering analysis performed by the Jet Propulsion Laboratory (JPL), free molecular and direct simulation Monte Carlo (DSMC) analyses were performed for two atmospheric passes. The drag coefficient was calculated using an area based on a Monte Carlo area determination program. Although the source of the discrepancy has not been determined, it has been confirmed that the original, simplified force-and-moment analysis performed by JPL produced results that were comparable to the high-fidelity DSMC analysis and that the source of the discrepancy lies elsewhere.

Liechty, Derek S.↗

NASA NTRS2012

Accuracy Assessments of Cloud Droplet Size Retrievals from Polarized Reflectance Measurements by the Research Scanning Polarimeter

We present an algorithm for the retrieval of cloud droplet size distribution parameters (effective radius and variance) from the Research Scanning Polarimeter (RSP) measurements. The RSP is an airborne prototype for the Aerosol Polarimetery Sensor (APS), which was on-board of the NASA Glory satellite. This instrument measures both polarized and total reflectance in 9 spectral channels with central wavelengths ranging from 410 to 2260 nm. The cloud droplet size retrievals use the polarized reflectance in the scattering angle range between 135deg and 165deg, where they exhibit the sharply defined structure known as the rain- or cloud-bow. The shape of the rainbow is determined mainly by the single scattering properties of cloud particles. This significantly simplifies both forward modeling and inversions, while also substantially reducing uncertainties caused by the aerosol loading and possible presence of undetected clouds nearby. In this study we present the accuracy evaluation of our algorithm based on the results of sensitivity tests performed using realistic simulated cloud radiation fields.

Rainbow↗

NASA NTRS2024

Simplified Meteorite Parent Body Alteration of Amino Acids By Hydrothermal Processes

Amino acids have been identified in extraterrestrial materials such as meteorites and returned samples from asteroids and comets. Some of these amino acids or their precursors may have formed on icy interstellar dust grains or at a later phase when these grains became incorporated into larger parent bodies. In this work, we simulated parent body aqueous alteration of the residues from irradiated interstellar ice analogs in the presence of relevant minerals (pulverized serpentinite and Allende meteorite). We tracked the change in amino acid abundances as a function of hydrothermal processing time and examined how these differed based on the presence of minerals. We find that the presence of minerals and their mineralogy can have a significant impact on the formation and destruction of amino acids during simulated aqueous alteration experiments.

Christopher K Materese↗

NASA NTRS1986

Numerical simulation of backward step and jet exhaust flows

Preparatory to a continuing study of efficient, high resolution flow structure capture on patched mesh systems, turbulent flowfield solutions for a tactical missile base flow problem are computed on two first level composite grids of differing topologies. One mesh is of the wraparound character and the other is a step mesh on the Cartesian topology. A simplified Baldwin-Lomax algebraic eddy viscosity model is applied in the wake region. Results for the two meshes are compared with each other and with other computations reported in the literature. The totality of results suggest both mesh topology and resolution are important factors in the accuracy of predictive results as well as turbulence modeling. Related to interests in high altitude laminar flows bluff bodies such as the AOTV, the paper also presents results from a solution from laminar flow over a backward facing step and makes comparison with the available classical experiment of Chapman, et al.

Lombard, C. K.↗

NASA NTRS1979

Nonlinear development of an electromagnetic filamentation instability

A simplified model of an electromagnetic filamentation instability that arises when two counterstreaming electron beams pass through a uniform ion background is treated by statistical mechanical techniques borrowed from fluid turbulence theory. Accumulation of magnetic energy at long wavelengths is predicted, as observed in the numerical simulations of Lee and Lampe.

Montgomery, D.↗

NASA NTRS1983

An inviscid three-dimensional analysis of the Space Shuttle main engine hot-gas manifold

A numerical study using an inviscid three-dimensional Lagrangian fluid dynamics code has been conducted as a part of an overall effort to understand the flow behavior in the SSME fuel side hot-gas manifold. The model simulates flow from the high-pressure fuel turbine exit through the transfer ducts, including the effects of swirl, inlet flow symmetry, and presence of straightening vanes and struts; a separate, more-detailed effort is in progress that includes viscosity and turbulence effects. The simplified model presented is divided into two parts, the first includes the 180-degree turnaround duct downstream of the turbine exit and the spherical fuel bowl section, while the second models the three transfer ducts. The two parts of the model are coupled together with the interface conditions being updated through iteration. Results indicate that a transverse pressure differential of 165 psi would be imposed on the turbine exit and that unstable flow separation occurs around the vanes, struts, and within the transfer ducts. The three transfer ducts show a mass flux split of approximately 41, 21, and 38 percent. Results to date are encouraging that certain flow characteristics can be usefuly represented using a relatively coarse grid inviscid code.

Liang, P. Y.↗