Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SiC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Neutron and Proton Radiation Damage and Isothermal Annealing of Irradiated SiC Schottky Power Diodes

NASA is exploring the potential use of nuclear reactors as power sources for future missions. These missions will require semiconductor switches to be placed in close vicinity to the reactor, in the midst of a high neutron and gamma radiation field. Cree SiC Schottky diodes, part number CSD10120A, rated at 10 A and 1200 V, were chosen as the test articles for this radiation-hardness study, since SiC is a wide bandgap semiconductor that has exhibited tolerance for such high radiation environments. As an extension of previous work regarding the degradation of SiC Schottky diodes in the presence of a neutron and gamma radiation field, isothermal annealing experiments were performed on these diodes after they were irradiated in The Ohio State University Research Reactor (OSURR). The experimental results demonstrate that even at an anneal temperature of only 175 C, a noticeable improvement in the electrical performance of the diodes, in the form of decreased series resistance, may be readily observed from I-V curve measurements. Also, since electrical components used for space applications will also be exposed to charged particle radiation from space, such as high energy protons in the Van Allen Radiation Belts surrounding earth, it is important that, in studying the effects of radiation-induced displacement damage, the effects of both neutron and charged particle radiation are considered. Therefore, the data obtained from this study were compared with the data obtained from previous 203 MeV proton irradiations, for which the same diode model was tested. To develop neutron-proton equivalencies which are relevant to the radiation electronics hardening community and the materials science community, comparisons of the degradation of the diodes for proton and neutron irradiation are made in two ways 1) on the basis of displacement damage dose, D{sub d} for protons and neutrons; and 2) on the basis of initially induced vacancies per atom (at a temperature of 0 K)(IIVPA0) for protons and Displacements per Atom (DPA) for neutrons. The equivalencies are especially good when the comparisons are made on the basis of IIVPA0, and DPA.

36 MATERIALS SCIENCE↗

Morphology of graphene on SiC(0001) surfaces.

Graphene is formed on SiC(000{bar 1}) surfaces (the so-called C-face of the crystal) by annealing in vacuum, with the resulting films characterized by atomic force microscopy, Auger electron spectroscopy, scanning Auger microscopy, and Raman spectroscopy. Morphology of these films is compared with the graphene films grown on SiC(0001) surfaces (the Si-face). Graphene forms a terraced morphology on the C-face, whereas it forms with a flatter morphology on the Si-face. It is argued that this difference occurs because of differing interface structures in the two cases. For certain SiC wafers, nanocrystalline graphite is found to form on top of the graphene.

36 MATERIALS SCIENCE↗

Direct measurement of local volume change in ion-irradiated and annealed SiC

Depth profiles of local volume expansions are precisely measured in 6H-SiC after irradiation at 150 K with 2 MeV Pt ions and following annealing at 770 K using transmission electron microscopy equipped with electron energy loss spectroscopy. It is found that the depth profile of local volume expansion from the as-implanted sample matches well with the depth profile of irradiation-induced local disorder measured by Rutherford backscattering spectrometry. Further, the local volume expansion increases linearly with local dose up to ~10%. By systematically comparing the depth profiles of local volume expansion and local relative disorder, it is revealed that the atomic volume of amorphous SiC continues to increase until it saturates at ~15% due to the increased chemical short-range disorder. This is believed to be one of the reasons for significant scatter in values of volume expansion previously reported for the irradiation-induced amorphous state of SiC.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Synthesis and properties of porous SiC ceramics

Porous silicon carbide (SiC) ceramics are produced using carbon matrices derived from natural wood. Such material is especially promising as it is environmentally friendly with attractive physical properties, including a high level of biocompatibility, chemical inertness, and mechanical strength. We have developed a forced impregnation process with further synthesis of SiC using natural wood as well as a variety of industrial carbon materials and compared the properties of these ceramics. The structure and composition of the materials obtained were investigated by Raman scattering spectroscopy. The hardness of the samples was estimated using the Vickers technique. It was shown that the phase composition and mechanical properties of synthesized SiC ceramics can be effectively controlled by the initial Si contents and temperature of the synthesis process. A large variety of options are demonstrated for materials development taking into account an optimal porosity selection for various practical applications.

36 MATERIALS SCIENCE↗

Monte Carlo Simulation of Electron Transport in 4H- and 6H-SiC

The Monte Carlo (MC) simulation of electron transport properties at high electric field region in 4H- and 6H-SiC are presented. This MC model includes two non-parabolic conduction bands. Based on the material parameters, the electron scattering rates included polar optical phonon scattering, optical phonon scattering and acoustic phonon scattering are evaluated. The electron drift velocity, energy and free flight time are simulated as a function of applied electric field at an impurity concentration of 1x10{sup 18} cm{sup 3} in room temperature. The simulated drift velocity with electric field dependencies is in a good agreement with experimental results found in literature. The saturation velocities for both polytypes are close, but the scattering rates are much more pronounced for 6H-SiC. Our simulation model clearly shows complete electron transport properties in 4H- and 6H-SiC.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Graphene growth by molecular beam epitaxy on the carbon-face of SiC

Graphene layers have been grown by molecular beam epitaxy (MBE) on the (0001) C-face of SiC and have been characterized by atomic force microscopy, low energy electron diffraction (LEED), and UV photoelectron spectroscopy. Contrary to the graphitization process, the step-terrace structure of SiC is fully preserved during the MBE growth. LEED patterns show multiple orientation domains which are characteristic of graphene on SiC (0001), indicating non-Bernal rotated graphene planes. Well-defined Dirac cones, typical of single-layer graphene, have been observed in the valence band for few graphene layers by synchrotron spectroscopy, confirming the electronic decoupling of graphene layers.

36 MATERIALS SCIENCE↗

Passivation effects of fluorine and hydrogen at the SiC–SiO 2 interface

High concentrations of defects at the SiC–SiO 2 interface greatly reduce the efficiency of the SiC-based microelectronics. Investigations of the defect passivation are thus of great importance. Here, we report first-principles density-functional-theory calculations for the effects of fluorine and hydrogen in passivating the defects at the SiC–SiO 2 interface. The calculations show that the isolated point defects involving excessive carbon atoms can be passivated by atomic fluorine and hydrogen, separately or combined. The results further suggest that molecular fluorine may be more effective for the passivation of the interface defects than molecular hydrogen and hydrogen fluoride.

74 ATOMIC AND MOLECULAR PHYSICS↗

Development of Medium Current Ion Implanter ''IMPHEAT'' for SiC

High productivity medium current ion implanter 'IMPHEAT' was developed for a commercial silicon carbide (SiC) device production. The beamline concept of IMPHEAT is the same as Nissin's ion implanter EXCEED 9600A for silicon device manufacturing. To meet the implantation process for SiC device fabrication, a new type ion source that can produce aluminum (Al) ion beam and a high temperature platen have been developed and installed. The maximum beam currents are 1 mA of Al{sup +}, 400 e{mu}A of Al{sup 2+} and 10 e{mu}A of Al{sup 3+}, and the time variation for these beam currents is less than {+-}10% per hour. The high-temperature platen can handle from 2 to 6 inch wafers. The wafer temperature reaches 600 deg. C for a 6 inch wafer and 500 deg. C for smaller size wafers by using the wafer holder. We have carried out the qualification test and the performance was confirmed as enough for commercial production of SiC devices.

43 PARTICLE ACCELERATORS↗

Graphene Formation on Step-free 4H-SiC(0001)

Step-free SiC was thermally decomposed in vacuum to better understand graphene formation in the absence of step fronts. Atomic force microscopy revealed graphene nucleating at surface pits that preferentially form along SiC{l_brace}1{bar 1}00{r_brace} planes. The density of these pits is 1 x 10{sup 8} cm{sup -2}, which is three orders of magnitude greater than the measured density of SiC threading dislocations. Additionally, Raman spectroscopy demonstrated that graphene on step-free regions have a redshifted 2D peak position and a smaller peak width than does graphene grown on stepped regions. This difference is attributed to film thickness, which is confirmed by cross-sectional transmission electron microscopy. Stepped regions have a graphitic film nearly 2 nm thick as compared to less than 0.7 nm for step-free regions.

36 MATERIALS SCIENCE↗

Studying the sintering behavior of BeO{sub x}-SiC{sub 1-x} Composite ceramic Material

The sintering behavior for BeO-SiC compacts composite ceramic at different sintering temperatures in air were conducted, resulting data indicated that the percentage of SiC (Wt% 5) sintered at 800 C deg. lead to higher sintering density of (1.80 gm/cm3). The x-ray diffraction pattern analysis indicated nothing change concerning the crystal structure. Microstructure development has been studied as a function SiC content. Silicon carbide found to be suppressed the sinter ability of the matrix BeO powder.

36 MATERIALS SCIENCE↗

Interfacial study and energy-band alignment of annealed Al{sub 2}O{sub 3} films prepared by atomic layer deposition on 4H-SiC

Al{sub 2}O{sub 3} films were prepared by atomic layer deposition using trimethylaluminum and H{sub 2}O at 250 Degree-Sign C on 4H-SiC substrates and annealed at 1000 Degree-Sign C in N{sub 2}. The as-deposited and annealed Al{sub 2}O{sub 3} films were measured and analyzed near the Al{sub 2}O{sub 3}/SiC interfaces by using an X-ray photoelectron spectroscopy (XPS) with etching processing. The XPS results showed that as-deposited Al{sub 2}O{sub 3} films were O-rich and converted to anhydride Al{sub 2}O{sub 3} films after annealed at 1000 Degree-Sign C in N{sub 2}. Si suboxides were found both at as-deposited and annealed Al{sub 2}O{sub 3}/SiC interfaces. Energy band shift between Al{sub 2}O{sub 3} and 4H-SiC was found after annealing. The conduction band offsets of as-grown and annealed Al{sub 2}O{sub 3}/SiC were 1.90 and 1.53 eV, respectively. These results demonstrated that Al{sub 2}O{sub 3} can be a good candidate to be applied in SiC metal-oxide-semiconductor devices.

36 MATERIALS SCIENCE↗

Sputtering of Si, SiC, InAs, InP, Ge, GaAs, GaSb, and GaN by electrosprayed nanodroplets

This article presents a characterization of the damage caused by energetic beams of electrosprayed nanodroplets striking the surfaces of single-crystal semiconductors including Si, SiC, InAs, InP, Ge, GaAs, GaSb, and GaN. The sputtering yield (number of atoms ejected per projectile's molecule), sputtering rate, and surface roughness are measured as functions of the beam acceleration potential. The maximum values of the sputtering yields range between 1.9 and 2.2 for the technological important but difficult to etch SiC and GaN respectively, and 4.5 for Ge. The maximum sputtering rates for the non-optimized beam flux conditions used in our experiments vary between 409 nm/min for SiC and 2381 nm/min for GaSb. The maximum sputtering rate for GaN is 630 nm/min. Surface roughness increases modestly with acceleration voltage, staying within 2 nm and 20 nm for all beamlet acceleration potentials and materials except Si. At intermediate acceleration potentials, the surface of Si is formed by craters orders of magnitude larger than the projectiles, yielding surface roughness in excess of 60 nm. The effect of projectile dose is studied in the case of Si. This parameter is correlated with the formation of the large craters typical of Si, which suggests that the accumulation of damage following consecutive impacts plays an important role in the interaction between beamlet and target.

36 MATERIALS SCIENCE↗

Synthesis of SiO{sub 2}/β-SiC/graphite hybrid composite by low temperature hot filament chemical vapor deposition

β-SiC thin films were synthesized directly on graphite by hot filament chemical vapor deposition at low temperature. SiH{sub 4} diluted in hydrogen was employed as the silicon source, while graphite was functioned as both substrate and carbon source for the as-grown β-SiC films. X-ray diffraction and Fourier transform infrared analysis indicate that SiO{sub 2}/β-SiC/graphite hybrid composite was formed after post annealing treatment, and its crystalline quality can be remarkably improved under optimized annealing conditions. The possible growth mechanism was proposed based on in situ etching of graphite by reactive hydrogen radicals at the atomic level.

36 MATERIALS SCIENCE↗

Wannier-Stark localization and terahertz electroluminescence of natural SiC superlattice

We report on efficient terahertz electroluminescence in the region of 1.5-2 THz from high electric field biased 6H-SiC n{sup +}−n{sup −}−n{sup +} structures with a natural superlattice at 7 K. The properties of the terahertz emission allow it to be attributed to spontaneous radiation resulting from electron Bloch oscillations in SiC natural superlattice. The use of the unique object, namely, natural superlattice of SiC allowed us to demonstrate a whole series of remarkable effects of Wannier-Stark localization and to get the intensive terahertz emission under steady-state electrical excitation of Bloch oscillations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural and magnetic properties of irradiated SiC

We present a comprehensive structural characterization of ferromagnetic SiC single crystals induced by Ne ion irradiation. The ferromagnetism has been confirmed by electron spin resonance, and possible transition metal impurities can be excluded to be the origin of the observed ferromagnetism. Using X-ray diffraction and Rutherford backscattering/channeling spectroscopy, we estimate the damage to the crystallinity of SiC, which mutually influences the ferromagnetism in SiC.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ab initio prediction of SiC nanotubes with negative strain energy

Single-layer SiC nanotubes (SiCNTs) are known to be metastable structures that is why only nanotubular fibers or polygrained nanotubes have been obtained experimentally. In this study, we report on how hydrogen helps to overcome the metastability of SiCNTs. Starting from SiC graphitic sheets, we analyzed the impact of either partial or full hydrogenation on the electronic properties and structural stability of SiCNTs. It is shown that, in general, hydrogenation widens the band gap of both SiC graphitic sheets and nanotubes and, irrespective of the difference in chirality and diameter, leads to the formation of energetically stable SiCNTs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural defects in epitaxial graphene layers synthesized on C-terminated 4H-SiC (0001{sup ¯}) surface—Transmission electron microscopy and density functional theory studies

The principal structural defects in graphene multilayers synthesized on the carbon-terminated face of a 4H-SiC (0001{sup ¯}) substrate were investigated using the high-resolution transmission electron microscopy. The analyzed systems include a wide variety of defected structures such as edge dislocations, rotational multilayers, and grain boundaries. It was shown that graphene layers are composed of grains of the size of several nanometres or larger; they differ in a relative rotation by large angles, close to 30°. The structure of graphene multilayers results from the synthesis on a SiC (0001{sup ¯}) surface, which proceeds via intensive nucleation of new graphene layers that coalesce under various angles creating an immense orientational disorder. Structural defects are associated with a built-in strain resulting from a lattice mismatch between the SiC substrate and the graphene layers. The density functional theory data show that the high-angular disorder of AB stacked bi-layers is not restoring the hexagonal symmetry of the lattice.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electrical and optical properties of stacking faults introduced by plastic deformation in 4H-SiC

The electrical and optical properties of stacking faults (SFs) introduced by plastic deformation in 4H-SiC were studied by Electron Beam Induced Current (EBIC) and cathodoluminescence (CL) methods. Partial dislocations and stacking faults in the (0001) glide planes perpendicular to the surface were introduced in n-type 4H-SiC under a well-controlled state of stress by cantilever bending at 550°C. CL measurements allow determining the multiplicity of the SFs (single or double). It is observed that the overwhelming majority of stacking faults are double Shockley type SFs (CL emission at 504 nm) that correlates well with previously published high resolution transmission electron microscopy (HRTEM) investigations. However, single Shockley type SFs (CL emission at 422 nm) of much smaller lengths are also observed in some areas near the scratched region from where the defects are nucleated. This suggests that the velocity of partial dislocation pairs under a given applied stress could be higher than that of single partial dislocations. It is also shown that in the EBIC mode, SFs produce a strong bright contrast, which can be explained by considering the SFs in 4H-SiC to be quantum wells of II type.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗