Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STAINLESS STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Design of an additively manufactured functionally graded material of 316 stainless steel and Ti-6Al-4V with Ni-20Cr, Cr, and V intermediate compositions

This study presents a method for designing a computationally informed gradient pathway to fabricate a functionally graded material (FGM) with terminal alloys of 316 stainless steel (SS316) and Ti-6Al-4V via directed energy deposition additive manufacturing with powder feedstock. In this work, the grading is accomplished through the introduction of intermediate elements and alloys (Ni-20Cr, Cr, and V) to avoid the brittle Fe-Ti intermetallic phases that form in the direct liquid phase joining of Ti-alloys and stainless steels. Using a combination of equilibrium calculations and Scheil-Gulliver simulations, a compositional pathway was designed to avoid deleterious phases. FGM samples were fabricated and experimentally characterized to determine the viability of the pathway. A change in phases from fcc to bcc was predicted to occur within the Ni-20Cr/Cr gradient region, and this was validated through experimental characterization. No detrimental phases (intermetallic, Laves, or σ phases) formed along the gradient path, demonstrating a successful computationally-informed design and fabrication of an FGM from SS316 to Ti-6Al-4V.

36 MATERIALS SCIENCE↗

Complexity of segregation behavior at localized deformation sites formed while in service in a 316 stainless steel baffle-former bolt

Here, post-irradiation evaluation was performed on a 316 stainless steel baffle former bolt harvested after 40 years of service in a pressurized water reactor. Microstructure analysis revealed the presence of defect-free dislocation channels and strain-induced twins, indicative of loading at a stress level close to yield stress at least once while in service. Primary radiation-induced Ni/Si precipitates were destroyed during channel and twin formation, and secondary, significantly coarser Ni/Si precipitates formed along newly formed Σ3 boundaries during the continued irradiation. Additionally, an elevated phosphorus level was observed inside the strain-induced twin. Complex chemistry inside the strain-induced feature may overlap with dislocation pileups and impact localized corrosion, material long-term performance, and safety.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Contribution of intragranular misorientations to the cold rolling textures of ferritic stainless steels

A combined experimental and simulation study of intragranular misorientation and texture development in ferritic stainless steels is presented herein. Cold rolling was performed on materials having different grain shapes to reveal variations of misorientations and texture with variations in microstructure. The experimental results were compared with predictions of the Visco-Plastic Self-Consistent (VPSC) model and the recently developed Grain-Fragmentation Visco-Plastic Self-Consistent (GF-VPSC) model. It is shown that the GF-VPSC model, incorporating the development of intragranular misorientations, provides a much better prediction of the texture strength compared to the standard VPSC model. The predictions of intragranular misorientation are also in good agreement with experimental measurements. Both experiments and simulations point to the importance of anisotropy of intragranular misorientation distributions in determining texture development and, importantly, texture strength.

36 MATERIALS SCIENCE↗

Sigma phase evolution and nucleation mechanisms revealed by atom probe tomography in a 347H stainless steel

The size evolution and phase composition of sigma phases were investigated for a 347H stainless steel subject to isothermal aging at 750 °C for up to 10,000 h. Scanning electron microscopy reveals that sigma phases are present before 336 h aging and they continue to grow for all aging times studied. Atom probe tomography shows little variation in the sigma phase composition with aging time up to 10,000 h, and only the C content decreases with aging time. The comparison of C concentration suggests that the sigma phase does not nucleate within the C-depleted matrix or precipitate free grain boundaries, leaving dissolving metastable M 23 C 6 as the only possible nucleation site. Based on the experimental results and thermodynamic simulations, the desirable Nb concentration is discussed to reduce the kinetics of sigma phase growth, and possible design directions are suggested to improve 347H.

36 MATERIALS SCIENCE↗

Aging effects on the mechanical properties of alumina-forming austenitic stainless steels

Isothermal aging and tensile evaluation were conducted for recently developed alumina-forming austenitic stainless steels (AFAs). Microstructural observation reveals that NiAl-type B2 and Fe{sub 2}(Mo,Nb)-type Laves phase precipitates form as dominant second phases in the austenitic matrix during aging at 750 C. At room temperature these precipitates increase the strength but decrease the ductility of the AFA alloys. However, when tested at 750 C, the AFA alloys did not show strong precipitation hardening by these phases, moreover, the elongation to fracture was not affected by aging. Fracture surface and cross-sectional microstructure analysis after tensile testing suggests that the difference of mechanical behaviors between room temperature and 750 C results from the ductile-brittle transition of the B2 precipitates. At room temperature, B2 precipitates are strong but brittle, whereas they become weak but ductile above the ductile-brittle transition temperature (DBTT).

36 MATERIALS SCIENCE↗

Multiscale mechanical fatigue damage of stainless steel investigated by neutron diffraction and X-ray microdiffraction

Mechanical fatigue behavior of AL6XN stainless steel as a typical type of planar slip alloy was investigated by in situ neutron diffraction and synchrotron-based X-ray microdiffraction methods. Under cyclic loading at a high strain amplitude (+/- 0.8%), the fatigue damage originated mainly from the accumulation of statistical stored dislocations, as clearly evidenced from a continuous increase in diffraction peak width with increasing the number of load cycles. However, under cyclic loading at a low strain amplitude (+/- 0.3%), the density of statistical stored dislocations became saturated just after a hundred loading cycles and the fatigue damage was mainly dominated by the accumulation of persistent [Alders bands (PLBs) and the complex interactions among various PLBs as evidenced through X-ray microdiffraction measurements. It was further found that there exists obvious grain-orientation-dependent local damage in the low-strain-amplitude fatigued sample. In particular, fatigued grains orientated with [001] paralleling the loading direction are subjected to compressive stress and contain a large number of broad PLBs in boundaries arraying the edge dislocation pile-ups, which generate a large stress gradient leading to local plastic instability. As a result, the highly localized stress field at PLBs in the cyclically-deformed sample at a low strain amplitude may explain the obvious cyclic stress softening.

36 MATERIALS SCIENCE↗

Influence of post deposition annealing on the microstructural evolution and tensile behavior of austenitic stainless-steel alloy 709 made by laser powder bed fusion

Structural materials used in the next generation nuclear reactors or other advanced energy systems are often required to withstand higher operating temperatures for a longer service life. Alloy 709 (A709), a Nb-containing and N-stabilized Fe-25Ni-20Cr austenitic stainless steel, has been recommended for high-temperature reactor constructions due to the better performance over the baseline Type 316H stainless steel. Here, in the current manuscript, for the first time, the microstructure evolution and tensile behavior of an A709 made by laser powder bed fusion (LPBF) is discussed. The as deposited and heat treated LPBF alloys are compared with a reference wrought alloy. Owing to the chemical segregation and a higher number of dislocations, the LPBF materials show a significantly higher density of precipitates formed during high temperature treatments when compared to the wrought samples. This is reflected when looking at the tensile properties, both at room and elevated temperatures, where LPBF samples show higher strengths compared to wrought materials.

36 MATERIALS SCIENCE↗

Microstructure of In-Core Molten Salt Corrosion Hastelloy N{sup R} and 316 Stainless Steel

Since 2011, many materials have been discussed for potential application in Fluoride salt-cooled High-temperature nuclear Reactors (FHRs), which are emerging as leading reactor concept for the next generation of nuclear reactors thanks to the benefits of a high degree of passive safety, high thermal efficiency, and low spent fuel volume. Among these discussed materials, Hastelloy N{sup R} and 316L stainless steel have been selected as the most likely candidate alloys for FHRs. To provide direct experience in integrating a real system using molten FLiBe salt for reactor operation, these two candidate alloys were experimentally tested in Li-7 enriched Li{sub 2}BeF{sub 4} (FLiBe) molten salt in the core of MIT Research Reactor (MITR) at 700 deg. C for 1000 hours. After in-core corrosion testing, some basic post-irradiation examinations (PIE) including weight change per unit area and surface profile as well as surface morphology were conducted in the MIT Nuclear Reactor Laboratory (NRL) and compared with out-of-reactor corrosion samples. The deep understanding of these alloys in high-temperature molten salt with strong neutron irradiation requires further microstructural analysis such as electron microscopy and energy dispersive spectroscopy on the surface and cross-section of the in-core corrosion tested samples. The challenge in the microstructural analysis is due to the high radioactivity from the gamma emitting isotopes formed in alloys during neutron irradiation. Additionally, the facilities that are authorized for radioactive materials are very limited on campus. In this study, the microstructure of the in-core corrosion tested Hastelloy N{sup R} and 316L stainless steel specimen was analyzed by using the facilities at the Center for Advanced Energy Studies (CAES) at Idaho National Laboratory (INL) through the Nuclear Science User Facilities (NSUF) Rapid Turnaround Experiment (RTE) program.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effect of Boron Content on Hot Ductility and Hot Cracking Susceptibility in 316L Austenitic Stainless Steel for Welding Components

Liquation cracking may occur in the heat-affected zone during welding. Two factors influence this phenomenon: the tensile stresses generated during welding and the potential loss of ductility due to the presence of a liquid film at grain boundaries depending on their chemical composition. Gleeble hot ductility tests have been used to study the combined effect of boron content and holding time on ductility drop in the liquation temperature range of a 316L type austenitic stainless steel. It is shown that high boron contents and short holding times promote the loss of ductility in this temperature range. Secondary ion mass spectrometry has been used to correlate mechanical results to boron distribution either at grain boundaries or in the bulk. Other welding tests have been performed to confirm the influence of boron content on hot cracking sensitivity of AISI 316L stainless steels. Results indicate that cracks appear on all specimens but at different strain levels. The higher the boron content is, the more the specimen exhibits tendency to hot cracking.

36 MATERIALS SCIENCE↗

Quantitative Nanoscale 3D Imaging of Intergranular Corrosion of 304 Stainless Steel Using Hard X-Ray Nanoprobe

Multi-modal imaging, which visualizes changes in the structure and chemistry of the same region of interest in materials by combining various techniques, is becoming attractive to material scientists. Here, we describe a multi-modal approach to investigate intergranular (IG) corrosion of sensitized stainless steels using synchrotron-based nanoscale X-ray imaging with sensitivity to microstructure and chemical composition. Three-dimensional tomography of 304 stainless steel samples deteriorated by IG corrosion, was carried out using X-ray fluorescence and differential phase contrast imaging. These findings were further supported with surface imaging and chemical analysis using scanning electron microscopy and energy dispersive X-ray spectroscopy. The combined quantitative structural and chemical analysis indicates that chromium segregates along grain boundaries, cracking is due to IG corrosion, and Cr-enrichment occurs on the cracked surfaces. Such quantitative 3D imaging of Cr 23 C 6 nucleation at grain boundaries and Cr enriched oxides at cracked surfaces is a powerful tool to correlate IG corrosion mechanisms at nanoscale with buried grain boundary structure and alloy composition. Such understanding of IG corrosion mechanisms is critical for both the development of predictive multiscale corrosion models, and the engineering of corrosion resistant materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis of Pitting Corrosion on Wrought and Additively Manufactured 316L Stainless Steel in Atmospheric Environments

Additive manufacturing of metal components enables rapid fabrication of complex geometries. However, metal additive manufacturing also introduces new morphological and microstructural characteristics which might be detrimental to component performance. Here we report the pitting corrosion properties of wrought and additively manufactured 316L stainless steel after atmospheric exposure to coastal environments and laboratory-created environments. Qualitative visualization in combination with quantitative analysis of resulting pits provided an in-depth understanding of pitting differences between wrought and additively manufactured 316L stainless steel and between coastal and laboratory-based exposure. Optical and scanning electron microscopy were utilized for visualization, while white light interferometry measured pits across approximately 5mm x 5mm areas on each sample. Post-processing of the interferometry data enables quantification of pitting attack for each sample in terms of both pit depth and pit volume. The pitting analysis introduced herein offers a new technique to compare pitting attack between different manufacturing processes and materials.

36 MATERIALS SCIENCE↗

Effect of Cobalt on the Microstructure and Corrosion Behavior of Martensitic Age-Hardened Stainless Steel

To evaluate the influence of cobalt on the microstructure and pitting behavior of martensitic age-hardened stainless steel (MASS), the microstructures and electrochemical behaviors were characterized by optical microscopy, scanning electron microscopy, transmission electron microscopy, x-ray photoelectron spectroscopy, potentiodynamic curve, electrochemical impedance spectroscopy, and Mott–Schottky analysis. Results indicated that adding cobalt reduced the grain size of the original austenite, refined the lath martensite, inhibited the precipitation of Cu-rich phases, and increased the content of reversed austenite. Compared with the cobalt-free steel, the cobalt-containing steel has a higher pitting potential, lower corrosion current density, and higher pitting resistance. The primary components of the passive film grown on the cobalt-free steel included (Cr, Fe) oxides, such as Cr{sub 2}O{sub 3}, Cr(OH){sub 3}, FeOOH, and Fe{sub 2}O{sub 3}. The cobalt-containing steel included the aforementioned components as well as Co, which was attributed to the formation of the passive film in the forms of CoFe{sub 2}O{sub 4}, Co(OH){sub 2}, and CoO. In addition, the synergy of the refined lath martensite and the precipitation of the Cu-rich phase induced an increase in corrosion resistance in MASS containing cobalt.

36 MATERIALS SCIENCE↗

Effect of Zener–Holloman Parameter on the Prior Austenite Grain size in a 12Cr-10Ni Precipitation-Hardenable Stainless Steel

Hot isothermal plane strain compression (PSC) tests were carried out on a 12Cr-10Ni martensitic precipitation-hardenable (PH) stainless steel, in the temperature range of 750-1050 °C, to study microstructural evolution during large strain deformation. The nature of stress–strain curves varies with Zener–Holloman parameter (Z) with specimens deformed at high Z showing steady-state behavior and those deformed at lower Z showing flow softening. Prior austenite grain size (PAGS), d, exhibited a strong correlation to Z showing a bilinear behavior represented as: d = (1803.9)Z{sup −0.094} for high Z deformation and d = (1456.2)Z{sup −0.058} for low Z deformation. Based on the above study, it is recommended to thermomechanically process 12Cr-10Ni steel at Z ≥ 10{sup 22} for obtaining products with good strength–toughness balance.

36 MATERIALS SCIENCE↗

Anisotropic spall failure of additively manufactured 316L stainless steel

The dynamic high strain rate tensile (spall) failure of additively manufactured (AM) materials is an area of great interest but much less understood than material failure under other loading regimes. The research presented here examines the effects of microstructure anisotropy in 316L stainless steel fabricated by laser powder bed fusion (LPBF) on its spall failure and properties. In this work, plate-on-plate impact experiments were performed using an 80-mm gas gun to investigate the spall behavior of AM fabricated sample discs with impact along the perpendicular and parallel orientations relative to build directions. Experiments were also performed on wrought 316L stainless steel as baseline material with uniform equiaxed grain microstructure for comparison with the AM material of same composition. The spall experiments involved free-surface velocity profiles measured using Photon Doppler Velocimetry (PDV) to capture the spall pull-back signals, combined with post-mortem analysis of the microstructure of soft-recovered impacted samples. In the case of AM samples, spall failure initiated preferentially at melt pool boundaries in both impact directions. The spall plane location and spall strength, however, were both heavily influenced by the orientation of the impact direction relative to the build direction in the AM samples. The spall behavior is also observed to be more complex in the samples impacted perpendicular to the build (through-thickness) direction, due in large part to the orientation of the microstructural features such as melt pool boundaries, laser scan tracks, and general grain morphology.

36 MATERIALS SCIENCE↗

Influence of injected interstitials on the void swelling in two structural variants of 304L stainless steel induced by self-ion irradiation at 500 °C

The two variants of AISI 304L stainless steel (SS) with different grain size distributions were ion irradiated at 500 °C to a peak dose of ~60 dpa. In the coarse-grained annealed variant, a peak swelling of ~12% was observed closer to the specimen surface rather than at the depth of peak displacement damage. The forward shift in depth between peak swelling and peak dose is proposed to be a consequence of suppression of void nucleation by injected interstitials. The swelling behavior in the front portion of the ion range mirrors that of neutron-induced swelling in this steel, exhibiting significant curvature with increasing dose as the swelling rate approaches the terminal swelling rate of 1%/dpa. Furthermore, an ultrafine grain variant of this steel produced by severely plastic deformation exhibits a similar suppression of void nucleation in the injected interstitial region, but also shows a significantly extended transient regime, not reaching the terminal swelling rate by 60 dpa.

304 stainless steel↗