Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Effect of Ni Content on Double-Target Co-sputtered CrNiN Coatings

Double-target co-sputtered CrNiN coatings were deposited by DC-pulsed magnetron reactive sputtering. The nickel content increases from 0.7 to 5.0 at.% with the increased Ni target current from 0.10 to 0.40 A. The influence of Ni content on preferred orientation and properties of CrNiN coatings was investigated. The results show that the doped Ni enters CrN to form (Cr,Ni)N solid solution. CrNiN coatings are mainly composed of CrN phase and demonstrate CrN(111) preferred orientation. All the coatings present columnar growth pattern. And the less obvious the preferred orientation, the more intense competitive growth, the less sufficient the columnar growth, the finer the columnar crystal and the denser the microstructure. In spite of the most dense structure with finest grains, the hardness of CrNiN coating containing 0.7 at.% Ni is the lowest. The hardness is affected by multiple effects of preferred orientation, grain size, solid solution strengthening, morphology and stress, especially the intensity degree of preferred orientation.

36 MATERIALS SCIENCE↗

Effect of substrate tilt on sputter-deposited AuTa films

Gold-tantalum alloy films are of interest for biomedical and magnetically-assisted inertial confinement fusion applications. However, growth mechanisms of such Au-Ta alloy films are not well understood. Here, we systematically study the effect of substrate tilt on properties of films deposited by direct current magnetron sputtering from a AuTa alloy target. Experimental data is correlated with distributions of landing energies and incident angles of sputtered and backscattered species calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Results reveal that the deposition rate and film density monotonically decrease with increasing substrate tilt. Properties are similar for films with a tilt of 40° and below: films are amorphous, with an average compressive stress of 0.5 GPa, a density of 16 g/cm 3 , and electrical resistivity of 200 μΩ cm. The critical substrate tilt angle for the onset of porosity, a transition to a reduced stress state, and an increase in electrical resistivity lies between 40 and 60°. Based on Monte Carlo simulations, these changes in film properties are correlated with an increase in the average impact angle of the ballistic component of atomic flux. Implications of these results to deposition onto non-planar substrates are discussed.

36 MATERIALS SCIENCE↗

Effects of substrate bias and tilt on magnetron sputtered boron carbide films

Maintaining high density and good mechanical properties at oblique angles for magnetron sputtered amorphous boron carbide films remains a challenge. In this study, we investigate the effect of the substrate bias on density, residual stress, mechanical properties, and morphology of boron carbide films deposited via direct current magnetron sputtering with a full-face erosion magnetron source in a mixed Ar-Ne plasma. Results show that films deposited at oblique substrate tilt angles on substrates biased at -50 V possess significantly lower oxygen content, superior mechanical properties, and higher density compared to their electrically grounded counterparts. In conclusion, these enhancements observed at oblique angles, while promising, come at the cost of larger residual compressive stress and higher Ne incorporation in films.

Materials science↗

Magnetron sputtered nanostructured cadmium oxide films for ammonia sensing

Nanostructured cadmium oxide (CdO) films were deposited on to glass substrates by reactive dc magnetron sputtering technique. The depositions were carried out for different deposition times in order to obtain films with varying thicknesses. The CdO films were polycrystalline in nature with cubic structure showing preferred orientation in (1 1 1) direction as observed by X-ray diffraction (XRD). Field-emission scanning electron microscope (FE-SEM) micrographs showed uniform distribution of grains of 30–35 nm size and change in morphology from spherical to elliptical structures upon increasing the film thickness. The optical band gap value of the CdO films decreased from 2.67 to 2.36 eV with increase in the thickness. CdO films were deposited on to interdigitated electrodes to be employed as ammonia (NH{sub 3}) gas sensor. The fabricated CdO sensor with thickness of 294 nm has a capacity to detect NH{sub 3} as low as 50 ppm at a relatively low operating temperature of 150 °C with quick response and recovery time. - Highlights: • Nanostructured CdO films were deposited on to glass substrates using magnetron sputtering. • Deposition time was varied in order to obtain films with different thicknesses. • The CdO films were polycrystalline in nature with preferred orientation along (1 1 1) direction. • The optical bandgap values of the films decreased on increasing the thickness of the films. • CdO films with different thickness such as 122, 204, 294 nm was capable to detect NH{sub 3} down to 50 ppm at operating temperature of 150 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of hydrogen atmosphere on pulsed-DC sputtered nanocrystalline Si:H films

Highlights: ► Nanocrystalline silicon films were made by pulsed-DC magnetron sputtering. ► A threshold hydrogen concentration was required. ► High defect density due to ion bombardment and oxygen contamination caused low conductivity. -- Abstract: Hydrogenated nanocrystalline silicon (nc-Si:H) films were prepared by a pulsed-DC magnetron sputtering method under an atmosphere of hydrogen/argon mixture. The effects of hydrogen concentration on the structural and electrical properties of the films were systematically investigated using grazing incidence X-ray diffraction (GIXRD), Raman spectroscopy, and conductivity measurement. A threshold hydrogen concentration of about 70% was found necessary before any crystallinity was detectable. The deposition rate decreased monotonically with increasing hydrogen concentration, while the conductivity varied with crystallite size. The abnormally low conductivity level of these nc-Si:H films was due to the extraordinarily high defect density, which was attributed both to the enhanced ion bombardment from the pulsed-DC plasma and to the oxygen contamination from the target.

36 MATERIALS SCIENCE↗

High energy-storage performance of 0.9Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}-0.1PbTiO{sub 3} relaxor ferroelectric thin films prepared by RF magnetron sputtering

Highlights: • High-quality PMN-PT 90/10 RFE thin films were prepared by RF magnetron sputtering. • The maximum discharged density of 31.3 J/cm{sup 3} was obtained in the 750-nm-thick film. • PMN-PT RFE films might be a promising material for energy-storage application. - Abstract: 0.9Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}-0.1PbTiO{sub 3} (PMN-PT 90/10) relaxor ferroelectric thin films with different thicknesses were deposited on the LaNiO{sub 3}/Si (100) by the radio-frequency (RF) magnetron sputtering technique. The effects of thickness and deposition temperature on the microstructure, dielectric properties and the energy-storage performance of the thin films were investigated in detail. X-ray diffraction spectra indicated that the thin films had crystallized into a pure perovskite phase with a (100)-preferred orientation after annealed at 700 °C. Moreover, all the PMN-PT 90/10 thin films showed the uniform and crack-free surface microstructure. As a result, a larger recoverable energy density of 31.3 J/cm{sup 3} was achieved in the 750-nm-thick film under 2640 kV/cm at room temperature. Thus, PMN-PT 90/10 relaxor thin films are the promising candidate for energy-storage capacitor application.

36 MATERIALS SCIENCE↗

Improved stability of aluminum co-sputtered indium zinc oxide thin-film transistor

Highlights: • We fabricated AOS TFTs using Al co-sputtered IZO thin films as active layers. • Low Al ratio in IZO thin films suppresses carrier concentration and oxygen vacancies. • Addition of 0.62 wt.% Al into IZO could reduce the chance of creating trap states. • Fabricated Al-IZO TFT has improved bias stability under bias stress conditions. • Optical transmittance of Al-IZO film greater than 90% in visible light (400–800 nm). - Abstract: The electrical performance and bias stability of radio-frequency magnetron co-sputtered aluminum-indium-zinc oxide (Al-IZO) thin-film transistors (TFTs) were investigated, with respect to the atomic proportions of Al. Other parameters such as the indium-zinc oxide (IZO) target power, oxygen partial pressure, and initial and process pressures of the chamber were fixed. At a low Al atomic ratio (0.62 wt.%), the electrical performance and bias stability of the Al-IZO TFT were optimized because of the suppression of the generation of oxygen vacancies and the strong bond between Al and oxygen atoms (Al–O; 501.9 kJ/mol). Compared to pure IZO TFTs, the Al-IZO TFT exhibited a small shift in the threshold voltage under bias stress conditions. A higher threshold voltage of −2.24 V and an improved subthreshold swing of 1.35 V/dec were also observed. We demonstrated that the Al-IZO TFT could be a promising candidate for switching and driving operations in mass-produced display applications.

36 MATERIALS SCIENCE↗

Correlation Between Optical Properties And Chemical Composition Of Sputter-deposited Germanium Cxide (GeO x ) Films

Germanium oxide (GeO x ) films were grown on (1 0 0) Si substrates by reactive Direct-Current (DC) magnetron sputter-deposition using an elemental Ge target. The effects of oxygen gas fraction, Г = O 2 /(Ar + O 2 ), on the deposition rate, structure, chemical composition and optical properties of GeOx films have been investigated. The chemistry of the films exhibits an evolution from pure Ge to mixed Ge + GeO + GeO 2 and then finally to GeO 2 upon increasing Г from 0.00 to 1.00. Grazing incidence X-ray analysis indicates that the GeO x films grown were amorphous. The optical properties probed by spectroscopic ellipsometry indicate that the effect of Г is significant on the optical constants of the GeO x films. The measured index of refraction (n) at a wavelength (λ) of 550 nm is 4.67 for films grown without any oxygen, indicating behavior characteristic of semiconducting Ge. The transition from germanium to mixed Ge + GeO + GeO 2 composition is associated with a characteristic decrease in n (λ = 550 nm) to 2.62 and occurs at Г = 0.25. Finally n drops to 1.60 for Г = 0.50–1.00, where the films become GeO 2 . A detailed correlation between Г, n, k and stoichiometry in DC sputtered GeO x films is presented and discussed.

36 MATERIALS SCIENCE↗

Enthalpy of Formation for Cu–Zn–Sn–S (CZTS) Calculated from Surface Binding Energies Experimentally Measured by Ion Sputtering

Herein, we report an analytical procedure to calculate the enthalpy of formation for thin film multinary compounds from sputtering rates measured during ion bombardment. The method is based on Sigmunds sputtering theory and the BornHaber cycle. Using this procedure, an enthalpy of formation for a CZTS film of the composition Cu1.9Zn1.5Sn0.8S4 was measured as -930 +/- 98 kJ mol1. This value is much more negative than the sum of the enthalpies of formation for the constituent binary compounds, meaning the multinary formation reaction is predicted to be exothermic. The measured enthalpy of formation was used to estimate the temperature dependence of the Gibbs free energy of reaction, which appears consistent with many experimental reports in the CZTS processing literature.

Baryshev, Sergey V.↗

Integration of microplasma with transmission electron microscopy: Real-time observation of gold sputtering and island formation

An in situ platform for characterizing plasma-materials interactions at the nanoscale in the transmission electron microscope (TEM) has been demonstrated. Integrating a DC microplasma device, having plane-parallel electrodes with a 25 nm thick Au film on both the cathode and anode and operating in 760 Torr of Ar, within a TEM provides real-time observation of Au sputtering and island formation with a spatial resolution of , 100 nm. Analyses of TEM and atomic force microscopy images show the growth of Au islands to proceed by a Stranski-Krastanov process at a rate that varies linearly with the discharge power and is approximately a factor of 3 larger than the predictions of a DC plasma sputtering model. The experiments reported here extend in situ TEM diagnostics to plasma-solid and plasma-liquid interactions.

METAMATERIALS↗

First-principles calculations for understanding microstructures and mechanical properties of co-sputtered Al alloys

Recent experimental studies show that co-sputtering solutes with Al, together, can refine columnar grain size around few tens of nanometers and promote the formation and enhance the stability of planar defects such as stacking faults (SFs) and grain boundaries (GBs) in Al alloys. These crystal defects and fine columnar grains result in high strength, enhanced strain hardening and thermal stability of Al alloys. Using first-principles density-functional theory (DFT) calculations, we studied the role of eleven solutes in tailoring kinetics and energetics of adatoms and clusters on Al {111} surface, stable and unstable stacking fault energies, and kinetic energy barriers for the migration of defects. The calculations show that most solutes can effectively refine columnar grain size by decreasing the diffusivity of adatoms and surface clusters. These solutes do not necessarily decrease the stacking fault energy of Al alloys, but reduce the formation energy of faulted surface clusters and increase the energy barriers for the recovery of faulted surface clusters. Correspondingly, the formation of SFs is kinetically promoted during sputtering. Furthermore, solutes are segregated into the core of Shockley partial dislocations and play a pinning effect on SFs, SF arrays and twin boundaries, enhancing the thermal stability of these crystal defects. These findings provide insights into the design of high-strength Al alloys for high-temperature applications.

36 MATERIALS SCIENCE↗

Sputtered In2O3 and ITO Thin Films Containing Zirconium

Additions of Zr to In{sub 2}O{sub 3} (IO) and In{sub 2}O{sub 3}:SnO{sub 2} (ITO) sputtered thin films are studied. We find that Zr allows IO-based films to maintain optical transparency as oxygen partial pressure in the sputter ambient decreases, and it also maintains high carrier concentration as the oxygen partial pressure increases. Applying this guidance could indicate pathways to improve film properties in large-area deposition systems. We also find that for films deposited at optimum oxygen partial pressure, the optical transparency of the IO-based films improves as Zr is added, especially in the near-infrared spectral region. Analysis of these films using Drude theory approximations indicate that optical improvement is due to an increase in dielectric permittivity caused by Zr addition. We propose that controlling dielectric permittivity may be an important strategy in improving other transparent conducting oxides (TCOs), as well as indicative of an important pathway to developing new TCOs.

14 SOLAR ENERGY↗

Origin of stress in radio frequency magnetron sputtered zinc oxide thin films

Highly c-axis oriented ZnO thin films have been deposited on silicon substrates by planar rf magnetron sputtering under varying pressure (10-50 mTorr) and oxygen percentage (50-100%) in the reactive gas (Ar + O{sub 2}) mixture. The as-grown films were found to be stressed over a wide range from -1 x 10{sup 11} to -2 x 10{sup 8} dyne/cm{sup 2} that in turn depends strongly on the processing conditions, and the film becomes stress free at a unique combination of sputtering pressure and reactive gas composition. Raman spectroscopy and photoluminescence (PL) analyses identified the origin of stress as lattice distortion due to defects introduced in the ZnO thin film. FTIR study reveals that Zn-O bond becomes stronger with the increase in oxygen fraction in the reactive gas mixture. The lattice distortion or stress depends on the type of defects introduced during deposition. PL spectra show the formation of a shoulder in band emission with an increase in the processing pressure and are related to the presence of stress. The ratio of band emission to defect emission decreases with the increase in oxygen percentage from 50 to 100%. The studies show a correlation of stress with the structural, vibrational, and photoluminescence properties of the ZnO thin film. The systematic study of the stress will help in the fabrication of efficient devices based on ZnO film.

36 MATERIALS SCIENCE↗

Epitaxial high saturation magnetization FeN thin films on Fe(001) seeded GaAs(001) single crystal wafer using facing target sputterings

It was demonstrated that Fe-N martensite ({alpha}') films were grown epitaxially on Fe(001) seeded GaAs(001) single crystal wafer by using a facing target sputtering method. X-ray diffraction pattern implies an increasing c lattice constant as the N concentration increases in the films. Partially ordered Fe{sub 16}N{sub 2} films were synthesized after in situ post-annealing the as-sputtered samples with pure Fe{sub 8}N phase. Multiple characterization techniques including XRD, XRR, TEM, and AES were used to determine the sample structure. The saturation magnetization of films with pure Fe{sub 8}N phase measured by VSM was evaluated in the range of 2.0-2.2 T. The post annealed films show systematic and dramatic increase on the saturation magnetization, which possess an average value of 2.6 T. These observations support the existence of giant saturation magnetization in {alpha}''-Fe{sub 16}N{sub 2} phase that is consistent with a recent proposed cluster-atom model and the first principles calculation [N. Ji, X. Q. Liu, and J. P. Wang, New J. Phys. 12 063032 (2010)].

36 MATERIALS SCIENCE↗

Highly-enhanced reflow characteristics of sputter deposited Cu alloy thin films for large scale integrated interconnections

An attempt to improve the reflow characteristics of sputtered Cu films was made by alloying the Cu with various elements. We selected Y, Sb, Nd, Sm, Gd, Dy, In, Sn, Mg, and P for the alloys, and ''the elasto-plastic deformation behavior at high temperature'' and ''the filling level of Cu into via holes'' were estimated for Cu films containing each of these elements. From the results, it was found that adding a small amount of Sb or Dy to the sputtered Cu was remarkably effective in improve the reflow characteristics. The microstructure and imperfections in the Cu films before and after high-temperature high-pressure annealing were investigated by secondary ion micrographs and positron annihilation spectroscopy. The results imply that the embedding or deformation mechanism is different for the Cu-Sb alloy films compared to the Cu-Dy alloy films. We consider that the former is embedded by softening or deformation of the Cu matrix, which has a polycrystalline structure, and the latter is embedded by grain boundary sliding.

36 MATERIALS SCIENCE↗

Reactive sputter deposition of pyrite structure transition metal disulfide thin films: Microstructure, transport, and magnetism

Transition metal disulfides crystallizing in the pyrite structure (e.g., TMS{sub 2}, with TM = Fe, Co, Ni, and Cu) are a class of materials that display a remarkably diverse array of functional properties. These properties include highly spin-polarized ferromagnetism (in Co{sub 1-x}Fe{sub x}S{sub 2}), superconductivity (in CuS{sub 2}), an antiferromagnetic Mott insulating ground state (in NiS{sub 2}), and semiconduction with close to optimal parameters for solar absorber applications (in FeS{sub 2}). Exploitation of these properties in heterostructured devices requires the development of reliable and reproducible methods for the deposition of high quality pyrite structure thin films. In this manuscript, we report on the suitability of reactive sputter deposition from metallic targets in an Ar/H{sub 2}S environment as a method to achieve exactly this. Optimization of deposition temperature, Ar/H{sub 2}S pressure ratio, and total working gas pressure, assisted by plasma optical emission spectroscopy, reveals significant windows over which deposition of single-phase, polycrystalline, low roughness pyrite films can be achieved. This is illustrated for the test cases of the ferromagnetic metal CoS{sub 2} and the diamagnetic semiconductor FeS{sub 2}, for which detailed magnetic and transport characterization are provided. The results indicate significant improvements over alternative deposition techniques such as ex situ sulfidation of metal films, opening up exciting possibilities for all-sulfide heterostructured devices. In particular, in the FeS{sub 2} case it is suggested that fine-tuning of the sputtering conditions provides a potential means to manipulate doping levels and conduction mechanisms, critical issues in solar cell applications. Parenthetically, we note that conditions for synthesis of phase-pure monosulfides and thiospinels are also identified.

36 MATERIALS SCIENCE↗

Highly oriented {delta}-Bi{sub 2}O{sub 3} thin films stable at room temperature synthesized by reactive magnetron sputtering

We report the synthesis by reactive magnetron sputtering and structural characterization of highly (111)-oriented thin films of {delta}-Bi{sub 2}O{sub 3}. This phase is obtained at a substrate temperature of 150-200 Degree-Sign C in a narrow window of O{sub 2}/Ar ratio in the sputtering gas (18%-20%). Transmission electron microscopy and x-ray diffraction reveal a polycrystalline columnar structure with (111) texture. The films are stable from room temperature up to 250 Degree-Sign C in vacuum and 350 Degree-Sign C in ambient air.

36 MATERIALS SCIENCE↗