Scale modeling considerations for thermal control coatings
Spacecraft thermal control coatings scale models, discussing temperature errors due to energy transport along surfaces
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Spacecraft thermal control coatings scale models, discussing temperature errors due to energy transport along surfaces
Developers of robotic scientific and commercial spacecraft are trending towards use of onboard autonomous capabilities for responding quickly to dynamic environments and rapidly changing situations. These capabilities need to know the state of the spacecraft’s health. Model-based fault diagnosis (MBFD) is an approach to estimating health by continuously verifying accurate behavior and diagnosing off-nominal behavior. Proper functioning of MBFD depends on 1) the quality of the diagnostic system model that is analyzed and compared to commands and onboard measurements to estimate a system’s health state, and 2) the correct functionality of the diagnosis engine interrogating the model and comparing its analyses to observed system behavior. Our goal is to develop Verification and Validation (V&V) techniques for MBFD to provide future missions sufficient confidence in its functionality and performance to deploy it on the systems they develop. Our work has been focused on infusing the techniques we developed earlier to an operational mission. First, we are constructing diagnostic models of a spacecraft attitude control system and updating our diagnostic engine so they can be demonstrated aboard the Arcsecond Space Telescope Enabling Research in Astrophysics (ASTERIA) mission, an operational spacecraft for which experiments in autonomy are being planned and executed, using the V&V techniques we have previously developed to assure they are both correct and complete. Since it is nearing the end of its life, ASTERIA provides a unique opportunity to demonstrate MBFD since the monitored components are expected to fail. Our demonstration will give system developers additional confidence to make timely, informed MBFD deployment decisions. Second, we will be completing performance assessments of the diagnostic engine/diagnostic model ensemble both on the flight system and ground-based testbeds to gain confidence in MBFD’s ability to run successfully in a spacecraft’s resource-constrained environment without adversely affecting other on-board activities. Finally, we are capturing our experience in preparing this demonstration in a set of checklists and guidance documents. Current practice includes high-level institutional guidance documents and standards, but at a high level of abstraction that does not necessarily address specific MBFD concerns. The purpose of the new checklists is to provide future mission developers clear, unambiguous, procedure-oriented guidance on assuring MBFD. This paper describes our work in these areas. For the first area, we describe the diagnostic models and updated diagnostic engine that will be used for the on-board demonstration. We describe how the V&V techniques we developed earlier are used to assure model and engine correctness and completeness. For the second area, we identify the performance measurement and assessment techniques used to characterize the diagnostic engine and diagnostic models, and discuss the effect of measured performance on overall mission operation. Finally, we present the checklist and guidance documents and describe how they meet the goals of providing system developers with clear, unambiguous, procedure-oriented guidance on MBFD assurance. We show how the techniques we have developed map into those artifacts.
Events which meet certain criteria from star-tracker images on board the Juno spacecraft have been proposed to be due to interplanetary dust particle impacts on its solar arrays. These events have been suggested to be caused by particles with diameters larger than 10 μm. Here, we compare the reported event rates to expected dust-impact rates using dynamical meteoroid models for the four most abundant meteoroid/dust populations in the inner solar system. We find that the dust-impact rates predicted by dynamical meteoroid models are not compatible with either the Juno observations in terms of the number of star-tracker events per day, or with the variations of dust flux on Juno's solar panels with time and position in the solar system. For example, the rate of star-tracker events on Juno's antisunward surfaces is the largest during a period in which Juno is expected to experience the peak impact fluxes on the opposite, sunward hemisphere. We also investigate the hypothesis of dust leaving the Martian Hill sphere originating either from the surface of Mars itself or from one of its moons. We do not find such a hypothetical source to be able to reproduce the star-tracker event-rate variations observed by Juno. We conclude that the star-tracker events observed by Juno are unlikely to be the result of instantaneous impacts from the zodiacal cloud.
The GRAIL spacecraft, Ebb and Flow (aka GRAIL-A and GRAIL-B), completed their prime mission in June and extended mission in December 2012. The excellent performance of the propulsion and attitude control subsystems contributed significantly to the mission's success. In order to better understand this performance, the Navigation Team has analyzed and refined the execution-error models for delta-v maneuvers. There were enough maneuvers in the prime mission to form the basis of a model update that was used in the extended mission. This paper documents the evolution of the execution-error models along with the analysis and software used.
Details of the Manned Maneuvering Unit (MMU) and its use is discussed. MMU simulations in the Space Operations Simulator (SOS) use two major devices. The first is a six-degree-of-freedom moving base carriage that allows the trainee freedom to fly the MMU in a large room and to match rates and dock with full scale targets. The second device is a large screen television display that provides the trainee with accurate views of tumbling targets from any point in a surrounding sphere up to 300 meters (1000 feet) in diameter. Astronauts used the SOS to train for the Solar Max repair mission and are now using it to train for a mission to recover the Palapa-B communications satellite. Subjective comparisons by astronauts of an orbit MMU performance to simulated MMU performance in the SOS indicate that the simulations are very realistic. Data from the Solar Max mission have resulted in two software upgrades that increase SOS fidelity for the next MMU mission: a model of contact dynamics between the MMU and a target spacecraft, and a model of MMU plume impingement forces during docking.
Two approaches to design a tri-band reflector antenna for the Advanced TDRSS are examined. Two reflector antenna configurations utilizing frequency selective surfaces for operation in three frequency bands, S, Ku, and Ka, are proposed. Far-field patterns and the antenna feed losses were computed for each configuration. An offset-fed single reflector antenna configuration was adapted for conceptual spacecraft design. CADAM drawings were completed and a 1/13th scale model of the spacecraft was constructed.
Determining the material type of objects in space is conducted using laboratory spectral reflectance measurements from common spacecraft materials and comparing the results to remote spectra. This past year, two different ground-truth studies commenced. The first, FORMOSAT III, is a Taiwanese set of six satellites to be launched in March 2006. The second is ANDE (Atmospheric Neutral Density Experiment), a Naval Research Laboratory set of two satellites set to launch from the Space Shuttle in November 2006. Laboratory spectra were obtained of the spacecraft and a model of the anticipated spectra response was created for each set of satellites. The model takes into account phase angle and orientation of the spacecraft relative to the observer. Once launched, the spacecraft are observed once a month to determine the space aging effects of materials as deduced from the remote spectra. Preliminary results will be shown of the FORMOSAT III comparison with laboratory data and remote data while results from only the laboratory data will be shown for the ANDE spacecraft.
The contents include: 1) Mission Accomplished; 2) Resource Report: Marshall Space Flight Center; 3) NASA 1995 Software of the Year Award; 4) Microbolometers Based on Epitaxial YBa2Cu3O(sub 7-x) Thin Films; 5) Garnet Random-Access Memory; 6) Fabrication of SNS Weak Links on SOS Substrates; 7) High-Voltage MOSFET Switching Circuit; 8) Asymmetric Switching for a PWM H-Bridge Power Circuit; 9) Better Ohmic Contacts for InP Semiconductor Devices; 10) Low-Bandgap Thermovoltaic Materials and Devices; 11) Digital Frequency-Differencing Circuit; 12) Imaging Magnetometer; 13) Computer-Assisted Monitoring of a Complex System; 14) Buffered Telemetry Demodulator; 15) Compact Multifunction Inspection Head; 16) Optical Detection of Fractures in Ceramic Diaphragms; 17) Eddy-Current Detection of Cracks in Reinforced Carbon/Carbon; 18) Apparent Thermal Conductivity of Multilayer Insulation; 19) Optimizing Misch-Metal Compositions in Metal Hydride Anodes; 20) Device for Sampling Surface Contamination; 21) Probabilistic Failure Assessment for Fatigue; 22) Probabilistic Fatigue and Flaw-Propagation Analysis; 23) Windows Program for Driving the TDU-850 Printer; 24) Subband/Transform MATLAB Functions for Processing Images; 25) Computing Equilibrium Chemical Compositions; 26) Program Processes Thermocouple Readings; 27) ICAN-Second-Generation Integrated Composite Analyzer; 28) Integrated Composite Analyzer with Damping Capabilities; 29) Computing Efficiency of Transfer of Microwave Power; 30) Program Calculates Power Demands of Electronic Designs; 31) Cost-Estimation Program; 32) Program Estimates Areas Required by Electronic Designs; 33) Program to Balance Mapped Turbopump Assemblies; 34) BiblioTech; 35) Controlling Mirror Tilt With a Bimorph Actuator; 36) Burst-Disk Device Simulates Effect of Pyrotechnic Device; 37) Bearing-Mounting Concept Accommodates Thermal Expansion; 38) Parallel-Plate Acoustic Absorbers for Hot Environments; 39) Adjustable-Length Strut Withstands Large Cyclic Loads; 40) Tool Indicates Contact Angles in Bearing Raceways; 41) Gravity Slides With Magnetic Braking; 42) High-Torque, Lightweight, Pneumatically Driven Wrench for Small Spaces; 43) Device for Testing Compatibility of an O-Ring; 44) Magnetic Heat Pump Containing Flow Diverters; 45) Variable-Tilt Helicopter Rotor Mast; 46) "Beach-Ball" Robotic Rovers; 47) Apparatus Would Measure Temperatures of Ball Bearings; 48) Flexible Borescope for Inspecting Ducts; 49) Texturing Copper To Reduce Secondary Emission of Electrons; 50) Automated Laser Cutting in Three Dimensions; 51) Algorithm Helps Monitor Engine Operation; 52) Flexible Revision of Data-Processing Communications; 53) Software for Managing the Use of Land; 54) Thermal Strap Increases Cryocooling Efficiency; 55) Reversible Nut With Engagement Indication; 56) Control Algorithms for Kinematically Redundant Manipulators; 57) Computed Hydrogen-Flow Splits in a Rocket Engine; 58) Pressure and Thermal Modeling of Rocket Launches; 59) Field of View of a Spacecraft Antenna: Analysis and Software; 60) Digital Controller for Laser-Beam-Steering Subsystem; 61) More About Beam-Steering Subsystem for Laser Communication; 62) Digital Controller for Laser-Beam-Steering Subsystem: Part 2; 63) Interface Circuit Board for Space-Shuttle Communications; 64) Automated Planning of Spacecraft Telecommunications; 65) Artifacts of Spectral Analysis of Instrument Readings; 66) Neural-Network Controller for Vibration Suppression; 67) Adaptive Finite-Element Computation in Fracture Mechanics; 68) Attitude Control for the Cassini Spacecraft; 69) Analytical Model for Fluid Dynamics in a Microgravity Environment; 70) Study of Rocket-Engine Joints Bonded by NVCU/NARloy-Z; 71) Improved Silicon Nitride for Advanced Heat Engines; 72) Parameters for Welding Aluminum/Lithium Alloys; 73) Lightweight Composite Intertank Structure; 74) Foil Patches Seal Small Vacuum Leaks; 75) Data Base on Cables and Connectors; 76) Effect of Clock Mode on Radiation Hardnessf an ADC; and 77) Fault-Tolerant Control for a Robotic Inspection System.
Mechanical models are commonly used in Guidance, Navigation and Controls (GN&C) system-level models to represent propellant slosh forces on launch vehicles and spacecraft. The slosh model parameters are typically predicted using semi-empirical analytical methods that are based on experimental data for high liquid-to-gas density ratios (such as water and air at standard sea level conditions). Model parameter calculations typically neglect any contribution to slosh dynamics from the gas phase. However, some cryogenic propellant systems operate in conditions where the density ratio can be orders of magnitude smaller. Analytical and computational modeling was used in this effort to investigate the effects of liquid-to-gas density ratio on slosh dynamics. No experimental data nor previous studies are available at this time that quantify the effect of liquid-to-gas density ratio on slosh dynamics. However, in a recent CFD study, results showed that density ratio can have a significant effect on slosh model parameters. In this study, a dual pendulum slosh model was created that distinctly represents both liquid and gas phase dynamics. Solution of the model, which invokes the Euler-Lagrange equations of motion, demonstrates that slosh frequency is a combination of liquid slosh frequency and gas phase slosh frequency. Additionally, it shows that slosh mass is reduced due to the opposing motion of the gas phase with respect to that of the liquid phase. The slosh model parameter trends were verified using Computational Fluid Dynamics (CFD) analysis results for various liquid-to-gas density ratios, tanks, and fill levels.
A one-directional dynamic model of a Stewart Platform was developed to assist NASA in analyzing the dynamic response in spacecraft docking operations. A simplified mechanical drawing was created, capturing the physical structure's main features. A simplified schematic diagram was developed in a lumped mass model from the mechanical drawing. Three differential equations were derived according to the schematic diagram. A Simulink diagram was created using MATLAB to represent the three equations. System parameters, including spring constants and masses, are derived in detail from the physical system. The model can be used for further analysis via computer simulation in predicting dynamic response in its main docking direction, i.e., up-and-down motion.
A 2.5D numerical plasma model of the interaction of the solar wind (SW) with the Solar Probe Plus spacecraft (SPPSC) is presented. These results should be interpreted as a basic plasma model derived from the SW-interaction with the spacecraft (SC), which could have consequences for both plasma wave and electron plasma measurements on board the SC in the inner heliosphere. Compression waves and electric field jumps with amplitudes of about 1.5 V/m and (12-18) V/m were also observed. A strong polarization electric field was also observed in the wing of the plasma wake. However, 2.5D hybrid modeling did not show excitation of whistler/Alfven waves in the upstream connected with the bidirectional current closure that was observed in short-time 3D modeling SPPSC and near a tether in the ionosphere. The observed strong electromagnetic perturbations may be a crucial point in the electromagnetic measurements planned for the future Solar Probe Plus (SPP) mission. The results of modeling electromagnetic field perturbations in the SW due to shot noise in absence of SPPSC are also discussed.
Our report devotes a 3D numerical hybrid model of the interaction of the solar wind with the Solar Probe spacecraft. The SPP model includes 3 main parts, namely, a non-conducting heat shield, a support system, and cylindrical section or spacecraft bus that contains the particle analysis devices and antenna. One observes an excitation of the low frequency Alfven and whistler type wave directed by the magnetic field with an amplitude of about (0.06-0.6) V/m. The compression waves and the jumps in an electric field with an amplitude of about (0.15-0.7) V/m were also observed. The wave amplitudes are comparable to or greater than previously estimated max wave amplitudes that SPP is expected to measure. The results of our hybrid simulation will be useful for understanding the plasma environment near the SPP spacecraft at the distance 4.5 Rs. Future simulation will take into account the charging of the spacecraft, the charge separation effects, an outgassing from heat shield, a photoionization and an electron impact ionization effects near the spacecraft.
Future spacecraft are being conceived that are highly flexible and of extreme size. The two features of flexibility and size pose new problems in control system design. Since large scale structures are not testable in ground based facilities, the decision on component placement must be made prior to full-scale tests on the spacecraft. Control law research is directed at solving problems of inadequate modelling knowledge prior to operation required to achieve peak performance. Another crucial problem addressed is accommodating failures in systems with smart components that are physically distributed on highly flexible structures. Parameter adaptive control is a method of promise that provides on-orbit tuning of the control system to improve performance by upgrading the mathematical model of the spacecraft during operation. Two specific questions are answered in this work. They are: What limits does on-line parameter identification with realistic sensors and actuators place on the ultimate achievable performance of a system in the highly flexible environment? Also, how well must the mathematical model used in on-board analytic redundancy be known and what are the reasonable expectations for advanced redundancy management schemes in the highly flexible and distributed component environment?
The NASA Orbital Debris Program Office (ODPO) studies all aspects of spacecraft end-of-life and orbital debris measurement, modeling, and mitigation. The reentry safety group within the ODPO uses the Object Reentry Survival Analysis Tool (ORSAT) to calculate the casualty risk due to reentry of spacecraft and other types of orbital debris. ORSAT models spacecraft as a collection of fragments that break apart from the parent object at a pre-defined “breakup altitude.” It then calculates the trajectory and aero-heating of these fragments to determine which fragments are completely destroyed and which survive to the ground and pose a risk to human population. Because of the historically high computational cost of these calculations, many simplifying assumptions have been made in the traditional calculation and analysis process used by the ODPO, some of which have been shown by recent research by the ODPO and others to be incorrect. Improvements to the ORSAT code and advancements in computer technology have vastly decreased the program’s processing time, and have allowed the ODPO to develop a capability for large-scale parametric studies and Monte Carlo reentry simulations that can aid in both the initial spacecraft design and provide more detailed and accurate risk analysis to spacecraft operators.
Calculated results based on two chromospheric flare models F1 and F2 of Machado, et al., (1980) are presented. Two additional models are included: F1*, which has enhanced temperatures relative to the weak-flare model F1 in the upper photosphere and low chromosphere, and F3 which has enhanced temperatures relative to the strong flare model F2 in the upper chromosphere. Each model is specified by means of a given variation of the temperature as a function of column mass. The corresponding variation of particle density and the geometrical height scale are determined by assuming hydrostatic equilibrium. The coupled equations of statistical equilibrium is solved as is radiative transfer for H, H-, He I-II, C I-IV, Si I-II, Mg I-II, Fe, Al, O I-II, Na, and Ca II. The overall absorption and emission of radiation by lines throughout the spectrum is determined by means of a reduced set of opacities sampled from a compilation of over 10 to the 7th power individual lines. That the white flight flare continuum may arise by extreme chromospheric overheating as well as by an enhancement of the minimum temperature region is also shown. The radiative cooling rate calculations for our brightest flare model suggest that chromospheric overheating provides enhanced radiation that could cause significant heating deep in the flare atmosphere.
The modeling and simulation of large dc spacecraft power systems necessitates considering the spacecraft power system as an interconnection of modular components. This paper presents a state-variable-based approach for dc spacecraft power system modeling and simulation. Each modular component is treated as a two-port network, and a state model is written with the port voltages as the inputs. The state model of a component is solved independently of the other components using its state transition matrix. The state variables of each component are updated assuming that the inputs are constant. Network analysis principles are then utilized to calculate the component inputs.
NASA has recently made the geometry and solid model for a spacecraft cabin ventilation fan prototype available to the public via electronic file downloads from the NASA Technical Report Server. This fan can be used for research and development by many organizations. The fan is 3.5 inches in diameter, 9 inches long, and weighed 3.6 lb. The NASA Quiet Space Fan was designed to make 3.64 inches of water pressure rise at 150.3 cfm of airflow at 12,000 rpm at standard air conditions of 70ºF and 14.7 psia. The performance of the metal version of the fan was measured to be 3.48 inches of water at 150.6 cfm at design speed. A low-noise blade-vane count was chosen to try to reduce tone noise generated by this fan by cutting off the first three blade passing frequency tones. In-duct microphone array measurements indicated that the most evident tones occur for frequencies of 1800 Hz (1 BPF) and 7200 Hz (4 BPF). Using reverberant room standard testing methods, the A-weighted sound power level for the fan operating at design point conditions was measured to be 71 dBA. This report describes the current set of publicly available information for this fan. The fan was designed, optimized, and tested with tools and techniques that NASA has traditionally used for turbofan engine research. This is one way that technology developed for aerospace applications can be used more broadly, since quiet and efficient fans are needed for many ventilation systems on spacecraft, aircraft, watercraft, land vehicles, and buildings.
NASA has recently made the geometry and solid model for a spacecraft cabin ventilation fan prototype available to the public via electronic file downloads from the NASA Technical Reports Server. This fan can be used for research and development by many organizations. The NASA Quiet Space Fan is 8.89 cm (3.50 in) in diameter, 22.9 cm (9.00 in) long, and the metal fan weighs 1.63 kg (3.6 lbm). The fan was designed to generate a system total pressure rise of 906 Pa (3.64 inches of water) at 0.709 m3/s (150.3 cfm) of airflow at 12,000 rpm (at 21.1ºC (70ºF) and 14.7 psia). Performance measured using standardized techniques showed good agreement with design and predicted values. A low-noise blade-vane count was chosen to reduce tonal noise generated by rotor-stator interaction for the first three blade passing frequency harmonics. In-duct microphone array measurements indicated that the most evident tones occur at frequencies of 1,800 Hz (1 BPF) and 7,200 Hz (4 BPF). Using reverberant room standard testing methods, the A-weighted sound power level for the fan operating at design point conditions was measured to be 71 dBA. This report describes the current set of publicly available information for this fan. The fan was designed, optimized, and tested with tools and techniques that NASA has traditionally used for turbofan engine research. This demonstrates that technology developed for aerospace applications can be used more broadly, since quiet and efficient fans are needed for many ventilation systems in spacecraft, aircraft, watercraft, land vehicles, and buildings.