Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SINTERED MATERIALS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Direct methanol feed fuel cell with reduced catalyst loading

Improvements to direct feed methanol fuel cells include new protocols for component formation. Catalyst-water repellent material is applied in formation of electrodes and sintered before application of ionomer. A membrane used in formation of an electrode assembly is specially pre-treated to improve bonding between catalyst and membrane. The improved electrode and the pre-treated membrane are assembled into a membrane electrode assembly.

Kindler, Andrew↗

Aerodynamic Performance and Acoustic Impacts of Varying Tip Speeds and Tripping Conditions on Small Rotors in an Anechoic Hover Chamber

Performance and acoustic measurements were taken in a hover chamber for various optimum hovering rotors (OPT2) and a commercial-off-the-shelf (COTS) rotor. A total of 10 rotors are included in this report, all of which have two blades and a tip radius of 0.1905 m (7.5 in.). For the OPT2, results for three additive manufacturing methods of fabrication are presented: stereolithography(SLA) using Accura Xtreme, SLA using FormLabs 10K resin, and selective laser sintering (SLS) using mineral-filled PA12 nylon material. All but one set of rotors were designed with a trailing edge bluntness that is 3% of the chord length, and one set was designed with a bluntness that is 1% of the chord length. Spanwise boundary layer trips were applied to the SLA, FormLabs and COTS rotors. Performance comparisons between untripped and tripped configurations demonstrate the impact of boundary layer state on rotor efficiency. Acoustic results, including periodic and broadband noise components, are presented. The effects of tripping these rotors near the leading edge are also presented. For some of the rotors, acoustic spectra of tip speed sweeps are presented to show how the frequency content changes with tip speed. Amplitude and frequency scaling methods are used to collapse broadband spectra at various tip speeds towards a unified curve. These findings contribute to the understanding of small rotor aeroacoustics and provide valuable datasets for computational model validation in urban air mobility applications.

eVTOL↗

Joining mechanism with stem tension and interlocked compression ring

A stem (34) extends from a second part (30) through a hole (28) in a first part (22). A groove (38) around the stem provides a non-threaded contact surface (42) for a ring element (44) around the stem. The ring element exerts an inward force against the non-threaded contact surface at an angle that creates axial tension (T) in the stem, pulling the second part against the first part. The ring element is formed of a material that shrinks relative to the stem by sintering. The ring element may include a split collet (44C) that fits partly into the groove, and a compression ring (44E) around the collet. The non-threaded contact surface and a mating distal surface (48) of the ring element may have conic geometries (64). After shrinkage, the ring element is locked onto the stem.

42 ENGINEERING↗

Wear-resistant boride composites with high percentage of reinforcement phase

A highly wear resistant sintered, hot pressed, or otherwise compacted ceramic composite material is described, consisting of two discrete phases of the form Al.sub.xMg.sub.yB.sub.14 where x and y .ltoreq.1 or like hard, orthorhombic compounds, and TiB.sub.2 or like Group IVB transition metal di-borides, and with an unexpectedly high content of transition metal di-boride in the range from 40 to 90 percent (28 to 85 volume percent).

Cook, Bruce Allan↗

Electrocatalyst comprising a crumpled transition metal dichalcogenide support loaded with monodispersed metal nanoparticles

An electrocatalyst comprises a crumpled transition metal dichalcogenide support loaded with catalytic metal nanoparticles through spontaneous reduction reactions. The support can be prepared by hydrothermal conversion of 2D nanosheets to 3D hierarchically crumpled sheets. As an example, using crumpled MoS 2 as a support, highly tunable Ru loadings were obtained using the electrostatic interaction between MoS 2 and RuCl 3 in solution. Control over Ru loading was leveraged to produce Ru—MoS 2 electrocatalysts that demonstrate different nitrogen reduction reaction activities, and which show varying resistance to electrochemical sintering and deactivation. Further, these high surface area materials can be utilized for many applications, including electrocatalysts, supercapacitors, and batteries.

Percival, Stephen↗

Physical and Biological Properties of Cobalt- and Copper-Doped Calcium Phosphates as Bone Substitute Materials

Arthritis, osteoporosis, and other bone diseases and defects are common medical issues worldwide. By utilizing ceramic biomaterials as bone substitutes to treat these diseases, bone regeneration can be promoted and toxicity from the substitute material can be limited. Calcium phosphate (CaP) ceramics have become popular as bone substitutes due to their biocompatibility and similarity in composition to natural bone. The purpose of this research was to investigate the physical properties and biological responses of CaP-based bone substitutes, doped with metal ions. Some metal ions are present in natural bone in small amounts, and recent studies show they affect the biological responses of CaPs significantly. Dopants such as magnesium (Mg), strontium (Sr), silicon (Si) and iron (Fe) alter the phase composition, mechanical properties, osteogenesis and angiogenesis properties of CaPs, depending on their concentration and method of addition. In the present study, the effects of cobalt (Co) and copper (Cu) on the physical and biological properties of two main CaP materials, brushite cement (BrC) and tricalcium phosphate (TCP), have been investigated. Different concentrations of dopants in forms of oxide and/or chloride were selected and their effect on phase composition, sintering behavior, density, setting time, compressive strength and in vitro interaction with osteosarcoma and osteoblast cells were studied. Different techniques of sample preparation, challenges during cement preparation and compact sample pressing, sintering, and methods of dopant addition are discussed. The presence of Cu in tricalcium phosphate was found to increase thermal stability of the material and decrease the impact of sintering temperature on porosity. In addition, Cu caused a reduction in expression of inflammatory gene markers by human osteoblast cells and an increased expression at early time points due of osteoinductive markers.The addition of Cu and Co to brushite cement caused an increase in thermal stability of the material, and the addition of Cu caused significant increase in setting time. Small dopant amounts of Co caused decrease in setting time, but higher amounts caused an increase. In addition, Cu dopant in small amounts resulted in an increase of compressive strength. Both Cu and Co led to a decrease in expression of inflammatory gene markers by osteoblast and osteosarcoma cells respectively, and Cu also caused an increase in osteoinductive marker expression. Thus, these results indicate that Cu and Co have a positive impact on the physical, mechanical and biological properties of calcium phosphate biomaterials.

Cummings, Haley V.↗

Structural, spectroscopic and dielectric investigations on Ba{sub 8}Zn(Nb{sub 6-x}Sb{sub x})O{sub 24} microwave ceramics

Ba{sub 8}Zn(Nb{sub 6-x}Sb{sub x})O{sub 24} (x = 0, 0.3, 0.6, 0.9, 1.2, 1.5, 1.8 and 2.4) ceramics were prepared through the conventional solid-state route. The materials were calcined at 1250 {sup o}C and sintered in the range 1400-1425 {sup o}C. The structure of the system was analyzed by X-ray diffraction, Fourier transform infrared and Raman spectroscopic methods. The theoretical and experimental densities were calculated. The microstructure of the sintered pellets was analyzed using scanning electron microscopy. The low frequency dielectric properties were studied in the frequency range 50 Hz-2 MHz. The dielectric constant ({epsilon}{sub r}), temperature coefficient of resonant frequency ({tau}{sub f}) and the unloaded quality factor (Q{sub u}) are measured in the microwave frequency region using cavity resonator method. The {tau}{sub f} values of the samples reduced considerably with the increase in Sb concentration. The materials have intense emission lines in the visible region. The compositions have good microwave dielectric properties and photoluminescence and hence are suitable for dielectric resonator and ceramic laser applications.

36 MATERIALS SCIENCE↗

Synthesis and characterization of noble metal borides: RuB{sub x}(x > 1)

Highlights: • Hexagonal RuB{sub 1.1} were synthesized using ruthenium and boron powders as raw materials during ball milling process. • Orthorhombic RuB{sub 2} were synthesized under high pressure (5 GPa) and high temperature (1000 °C) conditions. • Hexagonal Ru{sub 2}B{sub 3} have been synthesized under 5 GPa and 1200 °C. - Abstract: Noble metal borides RuB{sub 1.1}, RuB{sub 2} and Ru{sub 2}B{sub 3} have been synthesized by mechanical alloying and high pressure sintering methods using ruthenium (Ru) and boron (B) powders as raw materials. The crystal structures of borides were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results shown that only RuB{sub 1.1} with hexagonal crystal structure was synthesized during the ball milling process, the orthorhombic RuB{sub 2} was synthesized under high pressure (5 GPa) and high temperature (1000 °C) conditions, while the hexagonal Ru{sub 2}B{sub 3} can be synthesized under 5 GPa and 1200 °C. The mechanism of synthesis for the ruthenium borides (RuB{sub x}) are discussed in details.

36 MATERIALS SCIENCE↗

Effect of sintering on electrical properties of yttrium doped Li-based NASICON compounds

Electrical properties of Lithium based Li{sub 1.3}Al{sub 0.3-x}Y{sub x}Ti{sub 1.7}(PO{sub 4}){sub 3} (LAYTP) system was prepared using solid state reaction route. The samples were subjected to differing duration of sintering. X-ray diffraction was used to investigate the microstructure while density measurement was performed to determine the effect of sintering on the density of the prepared samples. Electrical properties of the material were studied using impedance spectroscopy, in frequency range 20 MHz to 1 Hz and in temperature range 303 K to 423 K. It was found that sample with least amount of yttrium and which was sintered for least duration had superior conductivity over other samples. It was also found that grain boundary conductivity improved marginally for sample with higher proportion of yttrium heat treated for longer duration.

36 MATERIALS SCIENCE↗

All solid thick oxide cathodes based on low temperature sintering for high energy solid batteries

Solid-state batteries (SSBs) could significantly improve the safety and energy density over conventional liquid cells. One key enabling technology is the use of solid electrolytes. NASICON-type Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP) is a very attractive solid-state electrolyte for the cathode side due to its high oxidation potential and high ionic conductivity. The usage, however, is limited by its large interfacial resistance against most of the cathode materials as well as the thermodynamic instability during high temperature sintering needed to achieve high mass density. Here we construct thin, percolative, and mixed conductive interphases through in situ low-melting-point liquid sintering. These mixed conductive interphases drastically improve the kinetics, leading to high-loading solid LATP/LiCoO 2 cathodes achieving capacity loading of up to ~6 mA h cm –2 . The technique is also applicable to Ni-rich cathode materials, achieving up to ~10 mAh cm –2 , which can lead to more than 400 W h kg –1 cells in SSBs. Furthermore, our composite cathodes show a ten-times and three-times area capacity improvement over the state-of-the-art cathodes using oxide and sulfide SSEs, respectively.

25 ENERGY STORAGE↗

Exothermic low temperature sintering of Cu nanoparticles

Sintering of the Cu nanoparticle at low temperatures resulted in exothermic behavior after its initiation. The calorimetry study of the heating of a 20 nm copper nanoparticles agglomerate revealed the evolution of 41.17 J/g of heat between 170 °C and 270 °C. High resolution transmission electron microscopy (HRTEM) images indicated that the heat generation was accompanied by sintering. The surface energy of the 20 nm copper nanoparticles was estimated to be 1.23 × 10{sup 3} erg/cm{sup 2} based on the heat released during sintering. The in situ high resolution transmission electron microscope (HRTEM) investigation showed that vigorous sintering occurred between 217 and 234 °C, which took place through the dislocation sintering mechanism. - Highlights: • Calorimetry showed exothermic behavior during heating of Cu nanoparticles between 170 and 270 °C. • Heat released due to the sintering of Cu nanoparticles was demonstrated by HRTEM. • Surface energy of 20 nm copper nanoparticles was estimated to be 1.23 × 10{sup 3} erg/cm{sup 2} during sintering. • Growth in crystallite sizes during sintering is disclosed by X-ray diffraction. • In situ HRTEM heating study showed occurrence of sintering through dislocation mechanism.

36 MATERIALS SCIENCE↗

Effect of sintering in ball-milled K{sub 2}Bi{sub 8}Se{sub 13} thermoelectric nano-composites

K{sub 2}Bi{sub 8}Se{sub 13} has many attractive features for thermoelectric applications. Recently, K{sub 2}Bi{sub 8}Se{sub 13}-based nanocomposite materials, consisting of nano-crystalline, micro-crystalline and amorphous phases, have been fabricated based on powder technology techniques. The Seebeck coefficient has been enhanced while the thermal conductivity has been decreased presenting, thus, interesting behavior. The behavior of the materials under heat treatment conditions is now of interest, as the application of sintering process is necessary for the development of thermoelectric modules. In this work, the crystallization of the K{sub 2}Bi{sub 8}Se{sub 13}-based nano-composites is studied using Differential Scanning Calorimetry. The results show that crystallization follows a multiple-step process with different activation energies. The thermoelectric properties are also discussed in the range that crystallization occurs. - Graphical Abstract: {beta}-K{sub 2}Bi{sub 8}Se{sub 13}-based nanocomposites follow a multiple-step crystallization process. Highlights: Black-Right-Pointing-Pointer K{sub 2}Bi{sub 8}Se{sub 13}-based composites consisting of nanocrystalline and amorphous phases. Black-Right-Pointing-Pointer Sintering results multiple-step crystallization with variable activation energies. Black-Right-Pointing-Pointer Thermoelectric properties follow a step-like behavior during sintering. Black-Right-Pointing-Pointer Properties are attributed to the strain relaxation, nucleation and grain growth.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrical conductivity of Sr{sub 2−x}VMoO{sub 6−y} (x = 0.0, 0.1, 0.2) double perovskites

Electrical conductivity of Sr{sub 2-x}VMoO{sub 6-y} (x = 0.0, 0.1, 0.2) double perovskites has been investigated in a reducing atmosphere at temperatures up to 800 °C. This material has a key application in solid oxide fuel cell anodes as a mixed ion and electron conductor. A solid state synthesis technique was used to fabricate materials and crystal structure was verified through x-ray diffraction. Subsequent to conventional sintering in a reducing environment, elemental valence states were indentified through x-ray photoemission spectroscopy on the double perovskite material before and after annealing in a hydrogen environment. Samples exhibited metallic like conduction with electrical conductivities of 1250 S/cm (Sr{sub 2}VMoO{sub 6-y′}), 2530 S/cm (Sr{sub 1.8}VMoO{sub 6-y″}), and 3610 S/cm (Sr{sub 1.9}VMoO{sub 6-y‴}) at 800 °C in 5% H{sub 2}/95% N{sub 2}, with a substantial increase in conductivity upon cooling to room temperature. Room temperature electrical conductivity values for Sr{sub 1.9}VMoO{sub 6-y‴} make it a candidate as the highest electrically conductive oxide known. Highly insulating secondary surface phases, Sr{sub 3}V{sub 2}O{sub 8}, and SrMoO{sub 4}, begin to reduce at 400 °C in a hydrogen environment, as confirmed by X-ray photoemission and thermal gravimetric analysis. This reduction, from V{sup 5+} and Mo{sup 6+} to lower valence states, leads to a large increase in sample electrical conductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Revealing multiscale competing processes in the solid-state synthesis of single-crystalline layered oxide positive electrodes

Solid-state synthesis involves a web of coupled chemical reactions and physical changes that unfold across multiple scales. Efforts to fine-tune its parameters have historically followed heuristic, trial-driven workflows that demand significant time and resources. In this study, we aimed to open this black box by employing multiscale in situ synchrotron imaging and diffraction. Using LiNi 0.5 Mn 0.3 Co 0.2 O 2 battery positive electrode material as a model system and Ba-based sintering aids, we reveal dopant segregation, intergranular mass transport, and porosity evolution as key drivers of single-crystalline particle formation. Notably, we uncovered a dynamic competition between particle-level grain coalescence and atomic-scale cation disordering, both of which are thermally activated yet have opposing impacts on battery performance. These findings highlight the coupled, multiscale nature of structure development and offer a mechanistic basis for optimizing the solid-state synthesis process. This framework provides a path toward more controlled, efficient, and scalable production of high-performance battery positive electrode materials.

36 MATERIALS SCIENCE↗

Improved thermal stability of oxide-supported naked gold nanoparticles by ligand-assisted pinning

We report a method to improve the thermal stability, up to 900 C, of bare-metal (naked) gold nanoparticles supported on top of SiO{sub 2} and SrTiO{sub 3} substrates via ligand-assisted pinning. This approach leads to monodisperse naked gold nanoparticles without significant sintering after thermal annealing in air at 900 C. The ligand-assisted pinning mechanism is described.

36 MATERIALS SCIENCE↗

Development of New Rocket Engine Liner Materials Based on Copper Alloys with Diamond Particle Additions

Novel copper-diamond materials containing particulate dispersions of diamond within a copper alloy matrix have been produced as next-generation rocket engine combustion chamber liner materials. These Copper-Diamond composite materials have significantly higher thermal conductivity than conventional liner materials and have the potential to increase the engine performance significantly. Liner fabrication techniques include hot pressing and spark plasma sintering, which are capable of scale up to full-size production parts. The materials have been evaluated for thermal cycling resistance and ease of manufacturing. The results indicate great promise of these materials and associated economics to replace state-of-the-art combustion chamber liner materials such as GRCop-84 and NARloy-Z. Novel combustion chamber fabrication processes are discussed, including cladding the liner with jacket materials.

Bhat, Biliyar N.↗

Synthesis and characterization of composite MgFe{sub 2}O{sub 4}-BaTiO{sub 3} multiferroic system

Multiferroic ceramics with the general formula (x)MgFe{sub 2}O{sub 4}-(1-x)BaTiO{sub 3} (x=0.4, 0.5, and 0.6) were synthesized by solid-state sintering process. From the x-ray diffraction analysis, it was observed that almost no chemical reaction occurs between the ferrite and the ferroelectric materials used to form the diphase composite systems. No impure phase was observed in all the sintered composite systems. Leakage current density, ferroelectric properties and dielectric properties were found to improve with the addition of the ferroelectric phase. For the composite with the least amount of ferrite, the values of remnant polarization (2P{sub r}) before and after dc magnetic poling at 7 kOe for 1 h were found to be 1.35 and 2.12 {mu}C/cm{sup 2}, respectively. This showed marked improvement as high as 57% and confirmed the coupling of the electrical dipoles with the magnetic field applied. All the studied composite systems proved to be multiferroic in nature. The highest magnetoelectric coupling coefficient of 50.2 mV/cm Oe was measured at dc magnetic field of 10 kOe along with ac frequency of 50 Hz at room temperature for the 0.6MgFe{sub 2}O{sub 4}-0.4BaTiO{sub 3} composite system. Magnetoelectric effect at resonance frequency increases by a factor of 80 compared to the other frequencies for such composite systems.

36 MATERIALS SCIENCE↗