Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Rolling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

The mechanical behavior of cross-rolled beryllium sheet

In response to the failure of a conical section of the Insat C satellite during certification testing, the use of beryllium for payload structures, particularly in sheet product form, is being reevaluated. A test program was initiated to study the tensile, shear, and out-of-plane failure modes of beryllium cross-rolled sheet and to apply data to the development of an appropriate failure criterion. Tensile test results indicated that sanding the surface of beryllium sheet has no significant effect on yield strength but can produce a profound reduction in ultimate strength and results obtained by finite element analysis. Critical examination of these test results may contribute to the modification of a JSC policy for the use of beryllium in orbiter and payload structures.

Henkener, J. A.↗
NASA NTRS1933

Rolling, yawing, and hinge moments produced by rectangular ailerons

Ailerons described in references 1, 2, and 3, are summarized in the form of empirical equations which relate the aileron dimensions and displacements to the rolling, yawing, and hinge moments for pitch angles of 0 and 12 degrees, corresponding to angles of attack of the wings of 4 and 16 degrees, respectively.

Heald, R H↗
NASA NTRS1952

Investigation of the Influence of Fuselage and Tail Surfaces on Low-speed Static Stability and Rolling Characteristics of a Swept-wing Model

Results are presented of a wind-tunnel investigation to determine influence of the fuselage and tail on static stability and rotary derivatives in roll of a model having 45 degrees sweptback wing and tail surfaces. The wing alone and the model without the horizontal tail showed marginal longitudinal stability near maximum lift. The longitudinal stability of the complete model was satisfactory. The vertical tail produced larger increments of rate of change of lateral-force and yawing-moment coefficients with wing-tip helix angle than the fuselage or the horizontal tail.

TAIL-WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1948

Free-flight Investigation at Transonic and Supersonic Speeds of the Rolling Effectiveness of a 42.7 Degree Sweptback Wing Having Partial-span Ailerons

An investigation of the rolling effectiveness at transonic and supersonic speeds of partial-span ailerons on a 42.7 degree sweptback wing having symmetrical circular-arc airfoil sections of 10-percent thickness ratio normal to the wing quarter-chord line has been made by means of rocket-propelled test vehicles. The results are compared with results of a supersonic wind-tunnel test at Mach number 1.9.

CONTROLS, LATERAL↗
NASA NTRS1950

Altitude-chamber Performance of British Roll-royce Nene II Engine IV : Effect of Operational Variables on Temperature Distribution at Combustion-chamber Outlets

Temperature surveys were made at the combustion-chamber outlets of a British Rolls-Royce Nene II engine. The highest mean nozzle-vane and mean gas temperatures were found to occur at a radius approximately 75% of the nozzle-vane length from the inner ring of the nozzle-vane assembly. Variations in engine speed, jet-nozzle area, simulated altitude, and simulated flight speed altered the temperature level but did not materially affect the pattern of radial temperature distribution.

COMBUSTION - TURBINE ENGINES↗
NASA NTRS1950

Altitude-chamber performance of British Rolls-Royce Nene II engine III : 18.00-inch-diameter jet nozzle

An altitude-chamber investigation of British Rolls-Royce Nene II turbojet engine was conducted over range of altitudes from sea level to 65,000 feet and ram pressure ratios from 1.10 to 3.50, using an 18.00-inch-diameter jet nozzle. The 18.00-inch-diameter jet nozzle gave slightly lower values of net-thrust specific fuel consumption than either the 18.41- or the standard 18.75-inch-diameter jet nozzles at high flight speeds. At low flight speeds, the 18.41-inch-diameter jet nozzle gave the lowest value of net-thrust specific fuel consumption.

ENGINES, TURBOJET↗
NASA NTRS1918

The Variation of Yawing Moment Due to Rolling

The aerodynamical constants of an airplane necessary for the discussion of stability are partly observed and partly calculated. Among the calculated coefficients is n(p), which is the variation of yawing moment due to rolling. (author)

Wilson, Edwin Bidwell↗
NASA NTRS1924

The Measurement of the Damping in Roll on a Jn4h in Flight

This investigation was carried out by the National Advisory Committee for Aeronautics for the purpose of measuring the value of L sub P in flight. The method consisted in flying with heavy weights on each wing tip, suddenly releasing one of them, and allowing the airplane to roll up to 90 degrees with controls held in neutral while a record was being taken of the airspeed, and angular velocity about the X axis. The results are of interest as they show that the damping found in the wind tunnel by the method of small oscillations is in general 40 per cent higher than the damping in flight. At 50 M. P. H. The flight curve of L sub P has a high peak, which is not indicated in the model results. It is also shown that at this speed the lateral maneuverability is low.

Norton, F H↗
NASA NTRS1925

Some problems on the lift and rolling moment of airplane wings

This report deals with the application of the airfoil and twisted wing theory to the calculation of the lift and rolling moment of airplane wings. Most of the results arrived at are strictly true only for wings of elliptic plan form. The investigation aims to give some indications of the accuracy with which the results can be applied to the wing forms in actual use.

Scarborough, James B↗
NASA NTRS1950

The effect of torsional flexibility on the rolling characteristics at supersonic speeds of tapered unswept wings

An analysis is presented of the effect of torsional flexibility on the rolling characteristics at supersonic speeds of tapered unswept wings with partial-span constant-percent-chord ailerons extending inboard from the wing tip. The geometric variables considered are aspect ratio, taper ratio, aileron span, and aileron chord. The shape of the wing-torsional-stiffness curve is assumed and the twisting moment is considered to result solely from the pressure distribution caused by aileron deflection, so that the necessity of using a successive-approximation method is avoided. Because of the complexity of the equations resulting from the analysis, numerical calculations from the equations are presented in a series of figures. A computational form is provided to be used in conjunction with these figures so that calculations can be made without reference to the analysis.

Tucker, Warren A↗
NASA NTRS1952

Investigation of Wear and Friction Properties Under Sliding Conditions of Some Materials Suitable for Cages of Rolling-Contact Bearings

An investigation of wear and friction properties of a number of materials sliding against SAE 52100 steel was conducted. These materials included brass, bronze, beryllium copper, monel, nichrome v, 24s-t aluminum, nodular iron, and gray cast iron. The metals investigated may be useful as possible cage (separator or retainer) materials for rolling-contact bearings of high-speed turbine engines. The ability of materials to form surface films that prevent welding is a most important factor in both dry friction and boundary lubrication. On the basis of wear and resistance to welding only, the cast irons were the most promising materials investigated; they showed the least wear and the least tendency to surface failure when run dry, and when boundary lubricated they showed the highest load capacity. On the basis of mechanical properties, nodular iron is superior to gray cast iron. Bronze had the lowest friction coefficient under dry sliding conditions. The results with brass, beryllium copper, and aluminum were poor and these materials do not appear, with regard to friction and wear, to be suitable for cages.

Johnson, Robert L↗
NASA NTRS1957

Linearized Lifting-Surface and Lifting-line Evaluations of Sidewash Behind Rolling Triangular Wings at Supersonic Speeds

The lifting-surface sidewash behind rolling triangular wings has been derived for a range of supersonic Mach numbers for which the wing leading edges remain swept behind the mark cone emanating from the wing apex. Variations of the sidewash with longitudinal distance in the vertical plane of symmetry are presented in graphical form. An approximate expression for the sidewash has been developed by means of an approach using a horseshoe-vortex approximate-lifting-line theory. By use of this approximate expression, sidewash may be computed for wings of arbitrary plan form and span loading. A comparison of the sidewash computed by lifting-surface and lifting-line expressions for the triangular wing showed good agreement except in the vicinity of the trailing edge when the leading edge approached the sonic condition. An illustrative calculation has been made of the force induced by the wing sidewash on a vertical tail located in various longitudinal positions.

Bobbitt, Percy J↗
NASA NTRS1958

A simplified method for approximating the transient motion in angles of attack and sideslip during a constant rolling maneuver

The transient motion in angles of attack and sideslip during a constant rolling maneuver has been analyzed. Simplified expressions are presented for the determination of the pertinent modes of motion as well as the modal coefficient corresponding to each mode. Calculations made with and without the derivatives for side force due to sideslip and lift-curve slope indicate that although these derivatives increase the total damping of the system they do not markedly affect the transient motion.

Sternfield, Leonard↗