Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Produced Waters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Foot-scale Evaluation of CO2-Responsive Polymer and CO2 Binary Fluid as an Alternative Fracturing Fluid for Enhanced Geothermal Systems

A foot-scale high-temperature true-triaxial fracturing apparatus was used to conduct hydraulic fracture tests on rock samples. The fracturing tests used different fluids including water, CO2, CO2 with water, and CO2 with a 1% polyallylamine (PAA)/water solution. The tests were conducted with both constant pressure injection and constant flow rate injection modes. CO2-based fracturing fluids were found to produce higher breakdown pressures, high transient flow rates, and produce higher-conductivity fractures as compared to water-based fracturing fluids. Additionally, faster pressurization rates with CO2-based fracturing fluids (obtained when fracturing at constant flow rate mode) are found to be associated with higher fracture conductivities. When fracturing with CO2-based fluids in the presence of a PAA aqueous solution, for example if the rock is saturated with 1wt% PAA in water, the volume expansion caused by CO2-induced crosslinking of PAA leads to a faster pressure increase due to the associated volume expansion and increase in viscosity. It was also found that CO2 as a fracturing fluid injected in hot dry rock (HDR) attain the highest fracture conductivity only when injected at very high flow rates, followed very closely by the CO2/PAA fracturing fluid system that generates fractures with, on average, similarly high conductivity values though independently of injection flow rate and using 1/6 of the mass of CO2 as compared to CO2 in HDR. Breakdown pressures were also similar for CO2 stimulation in HDR and CO2/PAA fluid system under identical injection flow rates. Finally, the well-known low viscosity of CO2 phase prevents the efficient transport of proppants while the reacted CO2/PAA fluid system is known to form a high viscosity binary fracturing fluid system with the potential to carry proppant in addition of being a fine fracturing fluid.

Enhanced Geothermal Systems, polyallylamine, Co2-r↗
DOE OSTI2020

The Installation of Direct Water-Cooling Systems to Reduce Cooling Energy Requirements for High-Performance Computing Centers

A large cluster of High-Performance Computing (HPC) equipment at the Lawrence Livermore National Laboratory in California was retrofitted with an Asetek cooling system. The Asetek system is a hybrid scheme with water-cooled cold plates on high-heat-producing components in the information technology (IT) equipment, and with the remainder of the heat being removed by conventional air-cooling systems. In order to determine energy savings of the Asetek system, data were gathered and analyzed two ways: using top-down statistical models, and bottom-up engineering models. The cluster, “Cabernet”, rejected its heat into a facilities cooling water loop which in turn rejected the heat into the same chilled water system serving the computer-room air handlers (CRAHs) that provided the air-based cooling for the room. Because the “before” and “after” cases both reject their heat into the chilled water system, the only savings is due to reduction in CRAH fan power. The top-down analysis showed a 4% overall energy savings for the data center (power usage effectiveness (PUE) —the ratio of total data center energy to IT energy— dropped from 1.60 to 1.53, lower is better); the bottom-up analysis showed a 3% overall energy savings (PUE from 1.70 to 1.66) and an 11% savings for the Cabernet system by itself (partial PUE of 1.51). Greater savings, on the order of 15-20%, would be possible if the chilled water system was not used for rejecting the heat from the Asetek system. About 37% of the heat from the Cab system was rejected to the cooling water, lower than at other installations.

Earni, Shankar↗
DOE OSTI2022

Distributed Real-time Plume Monitoring for Deep Sea Mineral Extraction​

In the emerging industry of deep-sea mining for minerals and deposits (e.g. polymetallic nodules for nickel, cobalt, copper, and manganese), more data is required to understand the effects of sediment plume generation and predict the distribution of disturbed sediment. There are two main sources of plume generation, the first being at the active mining site where the “collector” directly removes the top layer of the sea floor. The other is the “midwater plume” consisting of unwanted sediment that was collected during extraction that is pumped back into the aphotic zone. The vast majority of plume generation is caused by the collector, causing detrimental and long-lasting impacts on seafloor ecosystems due to the lack of wave activity or strong currents at the sea floor. Therefore, it is crucial to invest in the infrastructure to support the study and constant monitoring over a large area of the sea floor where plume generation is present. Due to the limited number of usable channels and power requirements, current subsea wireless communications technologies are not well suited to instrumenting the large areas of the sea floor needed to monitor plume migration. The scope of this effort is to transition experimental demonstrations of high-bandwidth, full-duplex scalable underwater laser communications to the seafloor in an open ocean environment. Specifically tackling challenges associated with the dynamic nature of the subsea world, including but not limited to, deployment logistics, sustainability, and range. The goal is to enable the internet of underwater things for deep sea industries by broadening the capabilities of subsea communications. By using high-precision laser transmitters, many of the challenges current subsea optical systems face can be circumvented, such as power consumption, interference, and bandwidth limitations. This approach lends itself to wireless interlinking multi-node networks, in series or parallel, facilitating the implementation of a wide array of sensor types. This interlinking allows all the data gathered from the network to be processed through a single hardline uplink to the surface, lowering the complexity required for near real-time data processing. Additionally, the laser control systems produce metadata that can be used to help characterize the water column between the nodes. Combining data from various sensors such as turbidity, temperature, current velocity with metadata such as beam attenuation and deflection can produce a high-resolution model of sea floor conditions around an active mining zone. The resulting near real-time model can be used to optimize location and flow rate of the mining operation to minimize and quantify the environmental impact.

Mons, Ishan↗
DOE OSTI2020

Impacts of Aerosol and Environmental Conditions on Maritime and Continental Deep Convective Systems Using a Bin Microphysical Model

A series of model simulations were conducted to investigate the effects of cloud condensation nuclei (CCN) loading and convective available potential energy (CAPE) on tropical maritime and midlatitude continental deep convection. Dynamical downscaling from global aerosol reanalysis was used to represent aerosol fields for the two convective regimes. We describe a control run and multiple sensitivity experiments using a limited-area model, employing spectral-bin cloud microphysics. The CCN loading is perturbed between the target maritime and continental conditions, roughly 40–2,000 cm -3 at 850 hPa and 1% supersaturation. Surface precipitation rates monotonically increase with increasing CCN loading for both the maritime and continental situations, while these monotonic increases are disrupted in the simulations with reduced CAPE. The increase in precipitation is in the form of convective precipitation, at the expense of stratiform precipitation. CCN increases promote increases in supercooled cloud water, in agreement with previous modeling studies. However, in the simulations investigated herein, the changes in supercooled water have different impacts on the cloud microphysics in the maritime and continental simulations. Increased supercooled water contents lead to more hail and less graupel in the continental simulation. For the maritime simulation, enhanced supercooled cloud water contents promote an increase in graupel since little or no hail is produced. This distinction is due to the difference in relative magnitudes and peak altitudes of supercooled water and snow amounts, which is further attributable to moisture and dynamical differences in the two cases.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

The environmental footprint of data centers in the United States

Much of the world's data are stored, managed, and distributed by data centers. Data centers require a tremendous amount of energy to operate, accounting for around 1.8% of electricity use in the United States. Large amounts of water are also required to operate data centers, both directly for liquid cooling and indirectly to produce electricity. For the first time, we calculate spatially-detailed carbon and water footprints of data centers operating within the United States, which is home to around one-quarter of all data center servers globally. Our bottom-up approach reveals one-fifth of data center servers direct water footprint comes from moderately to highly water stressed watersheds, while nearly half of servers are fully or partially powered by power plants located within water stressed regions. Approximately 0.5% of total US greenhouse gas emissions are attributed to data centers. We investigate tradeoffs and synergies between data center's water and energy utilization by strategically locating data centers in areas of the country that will minimize one or more environmental footprints. Our study quantifies the environmental implications behind our data creation and storage and shows a path to decrease the environmental footprint of our increasing digital footprint.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Spatio–Temporal Machine Learning for Regional to Continental Scale Terrestrial Hydrology

Integrated hydrologic models can simulate coupled surface and subsurface processes but are computationally expensive to run at high resolutions over large domains. Here we develop a novel deep learning model to emulate subsurface flows simulated by the integrated ParFlow–CLM model across the contiguous US. We compare convolutional neural networks like ResNet and UNet run autoregressively against our novel architecture called the Forced SpatioTemporal RNN (FSTR). The FSTR model incorporates separate encoding of initial conditions, static parameters, and meteorological forcings, which are fused in a recurrent loop to produce spatiotemporal predictions of groundwater. We evaluate the model architectures on their ability to reproduce 4D pressure heads, water table depths, and surface soil moisture over the contiguous US at 1 km resolution and daily time steps over the course of a full water year. The FSTR model shows superior performance to the baseline models, producing stable simulations that capture both seasonal and event–scale dynamics across a wide array of hydroclimatic regimes. The emulators provide over 1,000× speedup compared to the original physical model, which will enable new capabilities like uncertainty quantification and data assimilation for integrated hydrologic modeling that were not previously possible. Our results demonstrate the promise of using specialized deep learning architectures like FSTR for emulating complex process–based models without sacrificing fidelity.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Hemicellulose and starch citrate chitosan foam adsorbents for removal of arsenic and other heavy metals from contaminated water

Arsenic and other heavy metal contaminants in water are a significant global health threat. In this study, low-cost, sulfur-free, sustainable, water-insoluble materials with heavy metal remediation properties were produced from renewable resources such as starch, xylan, citric acid, and chitosan. Synthesized starch citrate-chitosan (SCC) foam and xylan citrate-chitosan (XCC) foam were flexible, porous, and elastic. The foams’ arsenic uptake in water was significantly greater than five different commercial metal remediating agents. The mercury and lead uptakes with the synthesized foams were similar to the performance of a commercial sulfur-based product, SorbaTech 450 (ST450). However, the cadmium and selenium uptakes were comparatively lower. The complexation of arsenic with oxygen and nitrogen of the SCC foam was shown with time-of-flight secondary ion mass spectrometry (TOF-SIMS). The XCC foam was also shown to adsorb potassium iodide (KI) at a similar rate to sodium chloride. This may be used to remediate water contaminated with radioactive materials, such as iodine 131.

Materials Science↗
DOE OSTI2021

Formation of Aerosol Nanoparticles by Gas-Phase Hydrolysis Reaction of Uranium Hexafluoride

The aerosol physics of uranyl particle formation has been addressed in this research using advanced aerosol instrumentation and an aerosol dynamics model. Based on the research works, we conclude that the formation and growth of aerosol particles by gas-phase UF6 hydrolysis strongly depends on the availability of water molecules in our reactor conditions. The total number concentration of the UO 2 F 2 particulate material that could be produced in the hydrolysis reaction is also regulated primarily by the availability of water molecule concentration. The higher the water molecule concentration, the higher the number and the larger the size of UO 2 F 2 aerosol particles that could be produced in a reactor custom-built at ORNL. Although the aerosol reactor was enabling the study of particle formation kinetics, the instrumentation was still insufficient in characterizing the chemical composition of the produced particles as well as the time-dependent evolution of the particulate species. The temporal evolution could impact the eventual fate of the particles upon release to the environment (i.e., the physio-chemical transformation, transport, and removal). On uranyl particle formation kinetics, we found that the growth rates of aerosol particles appeared to approach a single number in the range of 0.05 ± 0.03 - 0.08 ± 0.04 nm/s, statistically, as the ω value becomes smaller than 1. The size of primary particles from the UF6 hydrolysis at water-deprived condition was estimated to be 3.6 ± 0.4 nm; the higher the availability of water molecules, the larger the primary particles. The ability to precisely control the availability of water molecules in the reaction could lead to the production of nearly monodispersed aerosol particles. In other words, the result suggests that one can precisely manipulate the size of UO 2 F 2 aerosol particles by controlling the water vapor availability and interaction of water molecules with U F6 in the reaction. This finding has significant implications in the engineering manufacturing of fuel powder materials and possibly to future development and deployment of an environmental sampling apparatus.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2022

Drivers of Future Physical Water Scarcity and Its Economic Impacts in Latin America and the Caribbean

Future water scarcity is a global concern with significant impacts on the energy, water, and land (EWL) sectors. Countries in Latin America and the Caribbean (LAC) are significant producers of agricultural goods consumed around the world, so disruptions resulting from land and water scarcity in LAC are a source of global supply chain risk. Understanding where water scarcity in LAC could occur and what could drive that scarcity to emerge is critical for strategic resource management and planning, both regionally and globally. Assessing future water scarcity impacts in LAC is challenging given the multisector dynamic interactions among the EWL sectors and the multiple uncertainties acting across different spatial scales. We use scenario discovery to explore the drivers of future water scarcity, considering assumptions related to climate, socioeconomics, and the EWL sectors. Understanding what factors drive uncertainty across outcomes can help stakeholders in targeting long-term solutions and future data collection efforts. To illuminate these dynamics, we use a database consisting of a large ensemble of scenarios representing diverse worlds simulated using the Global Change Analysis Model. We quantify future water scarcity and its economic impacts across the scenarios using three metrics: (1) physical water scarcity, (2) water price, and (3) crop profit. We find that physical water scarcity and water price are driven primarily by reservoir storage capacity assumptions, highlighting the importance of strategic water infrastructure development in maintaining future water availability and accessibility. Crop profit is driven by a combination of water supply and demand assumptions, which emphasizes the complex nature of EWL multisector dynamics. While most of LAC is poised to have abundant land and water resources available for development, water basins in Mexico and along the Pacific coast of South America experience high levels of severity and uncertainty across the future scenarios for at least one of the metrics. We find that the drivers of extreme scarcity vary spatially and across the metrics, further highlighting the heterogeneity of the region and the importance of considering multiple metrics to assess water scarcity vulnerability.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Vertical Structure of Clouds and Precipitation During Arctic Cold–Air Outbreaks and Warm–Air Intrusions: Observations From COMBLE

The Arctic is marked by deep intrusions of warm, moist air, alternating with outbreaks of cold air down to lower latitudes. The typical vertical structure of clouds and precipitation during these two synoptic weather extremes is examined at a coastal site at 69°N in Norway. The Norwegian Sea is a corridor for warm-air intrusions (WAIs) and frequently witnesses cold-air outbreaks (CAOs). This study uses data from profiling radar, lidar, and microwave radiometer, radiosondes and other probes that were collected during the CAOs in the Marine Boundary Layer Experiment (COMBLE) between 1 December 2019 and 31 May 2020. Marine CAOs are defined in terms of thermal instability relative to the sea surface temperature, and WAIs in terms of equivalent potential temperature stratification between the surface and 850 hPa. Cloud structures in CAOs are convective, driven by strong surface heat fluxes over a long fetch of open water, with cloud tops rarely exceeding 6 km above sea level. The mostly open-cellular convection produces intermittent moderately-heavy precipitation at the observational site, notwithstanding the low precipitable water vapor (PWV). In contrast, WAIs are marked by high values of PWV and integrated vapor transport. Here, WAI clouds are synoptically driven, stratiform, with cloud tops often exceeding 5 km, sometimes layered, and generally producing persistent precipitation that can be heavier than in CAOs.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Going around the Kok cycle of the water oxidation reaction with femtosecond X-ray crystallography

The water oxidation reaction in photosystem II (PS II) produces most of the molecular oxygen in the atmosphere, which sustains life on Earth, and in this process releases four electrons and four protons that drive the downstream process of CO 2 fixation in the photosynthetic apparatus. The catalytic center of PS II is an oxygen-bridged Mn 4 Ca complex (Mn 4 CaO 5 ) which is progressively oxidized upon the absorption of light by the chlorophyll of the PS II reaction center, and the accumulation of four oxidative equivalents in the catalytic center results in the oxidation of two waters to dioxygen in the last step. The recent emergence of X-ray free-electron lasers (XFELs) with intense femtosecond X-ray pulses has opened up opportunities to visualize this reaction in PS II as it proceeds through the catalytic cycle. In this review, we summarize our recent studies of the catalytic reaction in PS II by following the structural changes along the reaction pathway via room-temperature X-ray crystallography using XFELs. The evolution of the electron density changes at the Mn complex reveals notable structural changes, including the insertion of O X from a new water molecule, which disappears on completion of the reaction, implicating it in the O—O bond formation reaction. We were also able to follow the structural dynamics of the protein coordinating with the catalytic complex and of channels within the protein that are important for substrate and product transport, revealing well orchestrated conformational changes in response to the electronic changes at the Mn 4 Ca cluster.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Tritium diffusion and formation in the bulk and defective surface of γ-LiAlO2 pellets: First-principles investigation

In tritium-producing burnable absorber rods (TPBAR), γ-LiAlO2 is used in the form of an annular ceramic pellet enriched with the 6Li isotope. When irradiated in a pressurized water reactor (PWR), the <sup>6</sup>Li pellets absorb neutrons and produce tritium (<sup>3</sup>H) through <sup>6</sup>Li + n <sup>3</sup>H + α. The 3H chemically reacts with the metal getter where it is captured and leads to formation of a metal hydride. For TPBARs to enable effective tritium production in PWRs, we investigated the <sup>3</sup>H diffusion pathways in the bulk and surface of γ-LiAlO<sub>2</sub> with different concentrations of lithium defects. The calculated results for bulk and low-index surfaces, thermal conductivity, 3H activation energy barriers, and the 3H diffusion coefficients in γ-LiAlO<sub>2</sub> are in good agreement with the available experimental values. In the bulk, our results show that the smallest activation energy barrier is 0.63 eV for substitutional <sup>3</sup>H diffusion with a diffusion coefficient of 3.25x10<sup>-12</sup> m<sup>2</sup>/s. After <sup>3</sup>H diffused from bulk to the surface, it could form different species (such as <sup>3</sup>H<sub>2</sub>, <sup>3</sup>H<sub>2</sub>O, C<sup>3</sup>H<sub>4</sub>) depending on the surface structure, vacancy types and the impurity carbon. Our results indicate that the <sup>3</sup>H<sub>2</sub> is the main product from γ-LiAlO<sub>2</sub> pellets. As the number of V<sub>Li</sub> vacancies and <sup>3</sup>H atoms increases under irradiation (<sup>3</sup>H-rich condition), <sup>3</sup>H<sub>2</sub>O release could increase from the surface of γ-LiAlO<sub>2</sub> pellets.

Jia, Ting↗
DOE OSTI2023

Developing algae as a sustainable food source

Current agricultural and food production practices are facing extreme stress, posed by climate change and an ever-increasing human population. The pressure to feed nearly 8 billion people while maintaining a minimal impact on the environment has prompted a movement toward new, more sustainable food sources. For thousands of years, both the macro (seaweed and kelp) and micro (unicellular) forms of algae have been cultivated as a food source. Algae have evolved to be highly efficient at resource utilization and have proven to be a viable source of nutritious biomass that could address many of the current food production issues. Particularly for microalgae, studies of their large-scale growth and cultivation come from the biofuel industry; however, this knowledge can be reasonably translated into the production of algae-based food products. The ability of algae to sequester CO 2 lends to its sustainability by helping to reduce the carbon footprint of its production. Additionally, algae can be produced on non-arable land using non-potable water (including brackish or seawater), which allows them to complement rather than compete with traditional agriculture. Algae inherently have the desired qualities of a sustainable food source because they produce highly digestible proteins, lipids, and carbohydrates, and are rich in essential fatty acids, vitamins, and minerals. Although algae have yet to be fully domesticated as food sources, a variety of cultivation and breeding tools exist that can be built upon to allow for the increased productivity and enhanced nutritional and organoleptic qualities that will be required to bring algae to mainstream utilization. Here we will focus on microalgae and cyanobacteria to highlight the current advancements that will expand the variety of algae-based nutritional sources, as well as outline various challenges between current biomass production and large-scale economic algae production for the food market.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

WHONDRS Summer 2019 Sampling Campaign: Global River Corridor Sediment FTICR-MS, Dissolved Organic Carbon, Aerobic Respiration, Elemental Composition, Grain Size, Total Nitrogen and Organic Carbon Content, Bacterial Abundance, and Stable Isotopes (v10)

The WHONDRS Summer 2019 Sampling (S19S) Campaign collected samples in 97 globally distributed river corridor systems between July and September 2019. Surficial streambed sediments were collected at three locations within each site (upstream, midstream, and downstream). Surface water was collected at the downstream site. This dataset includes a portion of the data types produced from the sediment samples and does not include any results from the surface water. Surface water data can be found at https://data.ess-dive.lbl.gov/view/doi:10.15485/1603775. The S19S campaign was designed with the science community to ask questions associated with links among core/transient metabolomes, microbial metabolism, biogeochemical function, and physical properties of watershed and river corridor systems. This data package was originally published in December 2020. It was updated in April 2021 (v2; modified files), May 2022 (v3; new and modified files), November 2022 (v4; new and modified files), January 2023 (v5 and v6; new and modified files), February 2023 (v7; new and modified files), August 2023 (v8; new and modified files), July 2025 (v9; new and modified files), and June 2026 (v10; new and modified files). Version 10 includes major restructuring of the files and their formats. See the change history in the readme for details. In addition to a readme, this data package also includes a file-level metadata (FLMD) file that describes each file and a data dictionary (DD) that describes all column/row headers and variable definitions. This dataset contains (1) readme, (2) data dictionary, (3) file level metadata, (4) sampling protocol, (5) a data checks report, (6) field metadata, (7) international generic sample number (IGSN) mapping file, (8) joint genome institute (JGI) mapping file, (9) a folder of site photos, and (10) a folder of sample data. The sample data folder contains (1) dissolved organic carbon (DOC, measured as non-purgeable organic carbon, NPOC) and FTICR methods; (2) respiration rates and normalized respiration rates calculated from laboratory sediment incubations, (3) X-ray fluorescence (XRF) elemental composition, (4) grain size distribution from the < 2 millimeter fraction of sediment, (5) total organic carbon and total nitrogen content, (6) bacterial abundance flow cytometry data, (7) sediment stable isotopes (C and N), (8) laboratory methods, (9) water and sediment mass and volume used in incubations, (10) a folder with code, inputs, and plots for the respiration rates, (11) a folder containing XRF data, (12) a folder containing unaligned, peak-picked high resolution characterization of dissolved organic matter from sediment via 12 Tesla Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) through the Environmental Molecular Sciences Laboratory (EMSL; https://www.pnnl.gov/environmental-molecular-sciences-laboratory), (12) and a folder containing processed FTICR-MS data. All files are .msa, .txt, .spx, .xml, .csv, .pdf, .txt, .jpg, or .jpeg.

13C↗
DOE OSTI2025

A life cycle assessment of e-hydrogen production using proton-exchange membrane water electrolysis coupled with desalination in Saudi Arabia

Hydrogen, considered a crucial element in the transition towards a sustainable energy future, offers the potential to mitigate greenhouse gas (GHG) emissions and reduce reliance on fossil fuels. Here, this study explores the viability of hydrogen production using proton exchange membrane water electrolysis (PEMWE) as a key driver of decarbonization within the Vision 2030 framework in the Kingdom of Saudi Arabia. A first-of-a-kind life cycle assessment (LCA) of electrolytic hydrogen (e-hydrogen) production using PEMWE in the Kingdom is performed. As the hydrogen will be produced in a freshwater scarce region, the inclusion of water desalination processes adds an important dimension to the assessment, reflecting the local context and resource availability. Two main renewable energy scenarios are assessed: solar energy through photovoltaics (PV) and wind energy through onshore turbines. The global warming potential (GWP) results indicate a GHG emissions reduction of up to 95 % compared to the state-of-the-art steam methane reforming process if the electrolysis process is powered exclusively by renewable electricity. The scenarios powered by solar and wind energy result in 3.66 and 0.76 kg CO 2 eq/kg H 2 , respectively. The metal depletion is assessed to consider the requirement of rare materials, with a 7.19 × 10 −2 kg Cu eq/kg H 2 for the solar scenario and 2.82 × 10 −2 kg Cu eq/kg H 2 for the wind scenario. A contribution analysis reveals that the majority of emissions in both scenarios originate from the electricity used for electrolysis, with the electrolyser itself contributing minimally. The absolute impact of the water desalination process is the same in both scenarios; however, it appears more prominent in the wind-powered case due to the significantly lower overall emissions in that scenario. The findings underscore the importance of renewable energy integration and process optimization in minimizing environmental impacts and advancing the sustainability of e-hydrogen production.

08 HYDROGEN↗
DOE OSTI2024

An Examination of Water-Related Melt Processes in Arctic Snow on Tundra and Sea-Ice

From April through June in 2019 and 2022, we monitored snow melt at three sites near Utqiaġvik, Alaska. Along 200-m lines we measured snow depth, density, stratigraphy, snow-covered area, and spectral albedo. Site 1 (ARM) was sloped tundra drained by water tracks. Site 2 (BEO) was flat polygonal tundra. Site 3 (ICE) was on undeformed landfast sea ice. All three sites were within a 6 km radius. Despite similar pre-melt snow distributions and weather, the melt progression differed markedly between sites. In 2019, by mid-melt, there was 40% less snow-covered area at ARM versus ICE, and 34% less snow-covered area at ARM versus BEO. The 2022 melt started 2 weeks later than in 2019 and was rapid, so smaller differences in snow-covered areas developed. In both years meltout dates varied by up to 25 days between sites, and more than 20 days within sites, with melt rates at locations only meters apart differing by up to a factor of seven. This melt diachroneity led to highly heterogeneous meltout patterns at all three sites. Our measurements and observations indicate that, in addition to reductions in snow reflective properties and wind-driven heat advection, the fate of meltwater plays a key role in producing melt diachroneity. We identify seven snow-water mechanisms that can enhance or inhibit melt rates, all largely controlled by the local topography and the nature of the substrate. These mechanisms are important because the most rapid changes in albedo coincide with the peak of water-snow melt interactions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Performance and flexibility improvements of Staged Pressurized Oxy-Combustion

Staged Pressurized Oxy-Combustion (SPOC) is a low-carbon coal combustion power technology being developed by Washington University in St. Louis (WUSTL). Oxy-combustion plants enable straightforward capture of carbon dioxide (CO 2 ) by removing most of the nitrogen in the combustion air prior to use, thereby burning fuel in near-pure oxygen instead of air, producing a flue gas containing primarily CO 2 and water. CO 2 capture at amounts > 90% is possible, often using cryogenic air separation. Oxy-combustion typically relies on flue gas recycle (FGR) to reduce the peak temperature and radiation that would otherwise occur in a fuel/oxygen only flame. SPOC reduces the peak temperatures of combustion by utilizing two or more pressurized boiler modules connected in series to produce fuel staging; hence, only a portion of the fuel is combusted in any given furnace module. This means that the thermal energy released at each stage can be captured and removed from the gases prior to subsequent stages, when more fuel is introduced. This allows the SPOC process to operate with minimal FGR, avoiding the associated efficiency losses and additional costs. Also, the process operates at an elevated gas-side pressure, reducing boiler size, enhancing heat transfer to achieve a compact boiler configuration as compared to an atmospheric-pressure boiler design, and allowing for recovery of the latent heat of the water from the flue gas at a temperature useful to the steam cycle. The resultant net efficiency of the system is over 3 percentage points greater than traditional atmospheric-pressure oxy-combustion, and 7 percentage points greater than the post combustion variant, representing a step-change improvement over first-generation capture technologies. To further develop the concept, WUSTL and the Electric Power Research Institute, Inc., organized a project with American Air Liquide, Inc., Doosan Babcock Limited, and the U.S. Department of Energy to investigate a practicable and workable boiler design. The team has identified the potential for enhanced process flexibility for controlling power generation over a wider load range than is normally available to conventional coal-fired power plants due to the staged nature of the heat release. With increasing intermittent renewable generator contribution, on-demand generators need to be highly flexible to participate in the future energy market, requiring extensive operation at reduced load. Conventional coal-fired steam generators typically face challenges in maintaining temperature control of the reheat steam and main steam at reduced loads. This results in inefficient operation, both in terms of the boiler efficiency and steam turbine heat rate. The results of this project show the SPOC process is capable of exceptional turndown, both on a stage basis and with the ability to bypass entire stages. Oxygen-supply flexibility was also investigated, as this is also a key consideration for the overall flexibility of the SPOC process given the operating constraints of conventional air separation units. A boiler design concept assessment was conducted and was focused on delivering compact and constructible design. The assessment checked appropriate tube operating metal temperatures at full load and at lower operating loads, balanced against the needs of efficient coal combustion, and the resultant slagging and ash environments. Combustion testing in the 100-kWth pressurized combustion test rig at WUSTL was carried out to validate the combustion, heat flux profiles and burnout at multiple loads. Combustion parameters investigated were flame stability, fuel burnout, ash composition, radiative heat flux, and temperature profiles. The results of these tests formed the basis of a full-scale boiler design that will encompass improvements in both efficiency and flexibility over conventional oxy-combustion processes. The air separation unit flexibility was investigated, and associated cost implications were addressed. Detailed economic assessment results for a 550 MWe net power block are also provided, allowing for a comparison against the baseline NETL oxy-combustion and post combustion capture cases.

20 FOSSIL-FUELED POWER PLANTS↗