Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Particle dispersion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A Three–Dimensional Nanoscale View of Electrocatalyst Degradation in Hydrogen Fuel Cells

The loss of platinum (Pt) electrochemically active surface area (ECSA) is a critical degradation mode that often becomes a limiting factor for heavy-duty proton exchange membrane fuel cell vehicles. High surface area carbon supports have been shown to improve Pt dispersion and limit detrimental ionomer-electrocatalyst interactions due to their large interior pore volume. Here, in this work, using automated scanning transmission electron tomography, the degradation of nanoparticles located on the interior versus exterior surfaces of the carbon support is compared following a catalyst-specific accelerated stress test (AST) of 90,000 voltage cycles between 0.6 V to 0.95 V. The results reveal a notable increase in median particle size for both interior and exterior Pt catalyst particles, with a slightly higher increase in particle size distribution and loss of specific surface area for the particles located on the exterior carbon surface. The fraction of Pt nanoparticles that reside within the interior of the carbon support also increased following the AST test, accompanied by evidence of an increase in average carbon mesopore size. Here, the results shed light on the degradation mechanisms affecting electrochemical properties and the enhanced particle accessibility at lower relative humidity.

08 HYDROGEN↗
DOE OSTI2020

Engineering Atomically Dispersed FeN 4 Active Sites for CO 2 Electroreduction

Atomically dispersed FeN 4 active sites have exhibited exceptional catalytic activity and selectivity for the electrochemical CO 2 reduction reaction (CO2RR) to CO. However, the understanding behind the intrinsic and morphological factors contributing to the catalytic properties of FeN 4 sites is still lacking. By using a Fe-N-C model catalyst derived from the ZIF-8, we deconvoluted three key morphological and structural elements of FeN 4 sites, including particle sizes of catalysts, Fe content, and Fe-N bond structures. Furthermore, their respective impacts on the CO2RR were comprehensively elucidated. Engineering the particle size and Fe doping is critical to control extrinsic morphological factors of FeN 4 sites for optimal porosity, electrochemically active surface areas, and the graphitization of the carbon support. In contrast, the intrinsic activity of FeN 4 sites was only tunable by varying thermal activation temperatures during the formation of FeN 4 sites, which impacted the length of the Fe-N bonds and the local strains. The structural evolution of Fe-N bonds was examined at the atomic level. First-principles calculations further elucidated the origin of intrinsic activity improvement associated with the optimal local strain of the Fe-N bond.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Confocal Raman Microscopy Investigation of Phospholipid Monolayers Deposited on Nitrile-Modified Surfaces in Porous Silica Particles

Phospholipid bilayers deposited on a variety of surfaces offer models for investigation of the lipid membrane structure and supports for biocompatible sensors. Hybrid-supported phospholipid bilayers (HSLBs) are stable membrane models for these investigations, typically prepared by self-assembly of a lipid monolayer over an n-alkane-modified surface. HSLBs have been prepared on n-alkyl chain-modified silica and used for lipophilicity-based chromatographic separations. The structure of these hybrid bilayers differs from vesicle membranes where the lipid head group spacing is greater due to interdigitation of the lipid acyl chains with the underlying n-alkyl chains bound to the silica surface. This interdigitated structure exhibits a broader melting transition at a higher temperature due to strong interactions between the lipid acyl chains and the immobile n-alkyl chains bound to silica. In the present work, we seek to reduce the interactions between a lipid monolayer and its supporting substrate by self-assembly of 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DMPC) on porous silica functionalized with nitrile-terminated surface ligands. The frequency of Raman scattering of the surface -C≡N stretching mode at the lipid–nitrile interface is consistent with an n-alkane-like environment and insensitive to lipid head group charge, indicating that the lipid acyl chains are in contact with the surface nitrile groups. The head group area of this lipid monolayer was determined from the within-particle phospholipid concentration and silica specific surface area and found to be 54 ± 2 Å 2 , equivalent to the head group area of a DMPC vesicle bilayer. The structure of these nitrile-supported phospholipid monolayers was characterized below and above their melting transition by confocal Raman microscopy and found to be nearly identical to DMPC vesicle bilayers. Their narrow gel-to-fluid-phase melting transition is equivalent to dispersed DMPC vesicles, indicating that the acyl chain structure on the nitrile support mimics the outer leaflet structure of a vesicle membrane.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Designing Ceria/Alumina for Efficient Trapping of Platinum Single Atoms

Cerium oxide (ceria) has been shown to be very effective at trapping platinum atoms, due to formation of stable surface complexes at step edges, where coordinatively unsaturated cerium cations are present. But ceria loses its effectiveness when heated to high temperatures, due to loss of surface area and growth in particle size associated with sintering of the oxide. Being a rare-earth, and with limited supplies worldwide, it is important to develop methods to improve the effectiveness of ceria as a catalyst support. Here we explore the performance for trapping Pt atoms when the ceria is supported on a high surface area alumina carrier. This helps create a more sustainable catalyst formulation, especially if we can retain the high dispersion of Pt seen on ceria supports. For this work, we studied the atom trapping efficacy of ceria/alumina samples with increasing ceria content (8 wt% - 50%) and contrasted the behavior with pure ceria. Electron microscopy reveals that when dispersed on alumina, ceria is present in the form of crystalline nanoparticles as well as isolated cerium ions. These two forms of ceria differ markedly in their ability to trap Pt atoms. Atomically dispersed cerium is present in the form of Ce 3+ cations on alumina, however this form of ceria is not effective for trapping Pt atoms. Our results show that the atom trapped Pt resides primarily on crystalline ceria nanoparticles. CO oxidation was used as a probe reaction to evaluate the performance of these Pt AT /ceria-alumina catalysts. As a result, we conclude that over the range of ceria loadings we investigated, 50% ceria/alumina represents the optimal catalyst support for achieving high surface area and atom trapping efficiency while helping reduce the total ceria content in this catalyst system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Fundamental Study of Migration Behavior of Cesium under the Unsaturated Condition through One-dimensional Column Simulating Soil around the Disposal Site - 20262

Using a packed column simulating unsaturated soil around the disposal site, flow experiments of cesium ions were conducted in order to examine the difference of retardation effect between saturated and unsaturated conditions. The column was packed with silica sand particles of 350 μm in diameter. In this study, it was confirmed that the X-ray CT images of the column showed that the water saturation was mostly uniform within the column under unsaturated conditions. The values of water saturation in the flow experiments of Cs ions were in a range from 0.85 to 0.93. The retardation coefficients(Rd) were estimated by applying the one-dimensional advection-dispersion equation to the experimental results. The comparison of the Rd-values estimated experimentally and theoretically showed that the experimental value was estimated to be larger than the theoretical value. This means that the theoretical value evaluated through a conventional method would bring the conservative value as an apparent retardation coefficient, at least when the flow direction is from top to bottom as shown in this study. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Report Summarizing the Mechanical Properties of a Large ODS Ferritic Alloy Ingot by Forging at High Temperatures for Future Mother Tube Production

Oxide dispersion strengthened (ODS) ferritic alloys are considered the benchmark fuel cladding and core structural material in advanced nuclear energy reactors that require high-temperature strength and creep properties and resistance to radiation damage. The ODS ferritic alloys including 14YWT are produced by mechanical alloying (MA), which is time-consuming and is associated with high manufacturing costs that are not beneficial to being used in advanced nuclear energy reactors. This report summarizes the accomplishments in FY24 in the INM program for producing an ODS ferritic alloy by high-deformation, high-temperature processing of reactive and ferritic alloy powders for advanced reactor fuel cladding applications. Following four hot forging experiments, it was concluded that several significant challenges were encountered that were difficult to overcome. These challenges were related to using high annealing temperatures for pressure assisted sintering processes to produce dense microstructures, but the high annealing temperatures result in long range diffusion of Ti through the bcc Fe lattice and react with the YIG particles that are distributed on the prior surfaces of the ferritic alloy powders. In addition, it was determined that the high deformations induced by forging at high temperatures were not very effective for fracturing the reactive YIG particles into smaller particles and distributing them into the interior of the ferritic alloy powders. Spark plasma sintering was attempted for shortening the time at high temperatures, which led to full densification but the microstructure characterization results still showed that Ti atoms diffused over long distances in the bcc Fe lattice and reacted with the YIG particles. Finally, a short 30 minute high intensity ball milling experiment was conducted on blended 14WT and YIG powders for inducing severe deformations that caused the initially spherical powders of 14WT decorated with the YIG particles on the surfaces to transform to flakes and fracturing of YIG particles into smaller particles that were incorporated into the bcc Fe lattice. Two forgings were performed with the high intensity milled powders: first annealing for 20 minutes at 850ºC followed by forging and second annealing for 20 minutes at 1,100ºC followed by forging. At 850ºC, Ti atoms are effectively immobile, thus allowing for densification albeit incomplete. The deformation by forging after annealing for 20 minutes at 1,100ºC favored dynamic recrystallization processes that led to nano-size grains with very high stored energy due to high dislocation density. The corresponding VH data showed significant hardening that correlated with estimated strengthening of ~1650 MPa. This hybrid processing approach combining high intensity ball milling of powder with annealing and forging showed the most promise for producing an oxide dispersing strengthened ferritic alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Iridium Surface Oxide Affects the Nafion Interface in Proton-Exchange-Membrane Water Electrolysis

Proton-exchange-membrane water electrolyzer (PEMWE) catalyst layers consist of aggregates of catalyst particles (typically iridium) and ionomer (typically Nafion). Prior work suggests that the oxide form of Ir affects the kinetics of the oxygen-evolution reaction. However, because most catalyst-benchmarking studies are conducted ex situ in liquid electrolytes, it remains unclear how the ionomer is influenced by the catalyst oxide and affects overall cell performance. Using a suite of experimental techniques, we conduct fundamental investigations into model ink (catalyst and ionomer dispersed in solution) and thin-film systems to inform cell-level overpotential analysis as a function of three forms of Ir (metallic Ir m , oxyhydroxide IrOOH, and oxide IrO 2 ). Furthermore, nafion on Ir m has a high degree of phase separation and higher swelling, likely improving the ionic conductivity. Additionally, Nafion binds most strongly to IrOOH, likely yielding reduced kinetic overpotentials. These findings highlight the intricacies of the ionomer/Ir interface and provide insight into all catalyst-layer systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Extracting correlation effects from momentum-resolved electron energy loss spectroscopy: Synergistic origin of the dispersion kink in Bi 2.1 Sr 1.9 CaCu 2 O 8 + x

We employ momentum-resolved electron energy loss spectroscopy (M-EELS) on Bi 2.1 Sr 1.9 CaCu 2 O 8 + x to resolve the issue of the kink feature in the electron dispersion widely observed in the cuprates. To this end, we utilize the GW approximation to relate the density response function measured in M-EELS to the self-energy, isolating contributions from phonons, electrons, and the momentum dependence of the effective interaction to the decay rates. The phononic contributions, present in the M-EELS spectra due to electron-phonon coupling, lead to kink features in the corresponding single-particle spectra at energies between 40 and 80 meV, independent of the doping level. We find that a repulsive interaction constant in momentum space is able to yield the kink attributed to phonons in ARPES. Hence, our analysis of the M-EELS spectra points to local repulsive interactions as a factor that enhances the spectroscopic signatures of electron-phonon coupling in cuprates. We conclude that the strength of the kink feature in cuprates is determined by the combined action of electron-phonon coupling and electron-electron interactions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Dirty bomb source term characterization and downwind dispersion: Review of experimental evidence

Dirty bombs are considered one of the easiest forms of radiological terrorism, a form of terrorism based on the deliberate use of radiological material to cause adverse effects in a target population. One U.S. Government official has even described a dirty bomb attack as “all but inevitable”. While people in the vicinity of the blast may experience acute radiation effects, people downwind may unknowingly be contaminated by the radioactive airborne particulate and face increased long-term cancer risk. The likelihood of increased cancer risk depends on the radionuclide used and its specific activity, its aerosolization potential, the particle sizes generated in the blast, and where a person is with respect to the detonation. Different studies have reported that plausible radionuclides for dirty bomb include 60 Co, 90 Sr, 137 Cs, 192 Ir, 241 Am based on their availability in commercial sources as well as safeguards, the amount needed for adverse health effects, previous mishandling of radionuclides and malicious uses. In order to have increased long-term cancer risk, the radionuclide would have to deposit inside the body by entering the respiratory tract and then possibly migrate to other organs or bones (ground shine is not considered in this paper because areas affected by the event will likely become inaccessible). This implies that the particles will have to be smaller than 10 μm to be inhaled. Experiments involving the detonation of dirty bombs have shown that particles or droplets smaller than 10 μm are generated, independently from the initial radionuclide or its state (e.g., powder, solution). Atmospheric tests have shown that in unobstructed terrain, the radionuclide laden cloud can travel kilometers downwind even for relatively small amounts of explosives. Furthermore, buildings in the path of the cloud can change the dose rate. For instance, in one experiment with a single building, the dose rate was 1–2 orders of magnitude lower behind the obstacle compared to its front face. For people walking around, the amount of particulate deposited on them and inhaled will depend on their path relative to the cloud, resulting in the counterintuitive result that the closer people may actually not be the ones more at risk because they could simply miss the bulk of the cloud in their wandering. In summary, the long-term cancer risk for people caught in a dirty bomb cloud away from the detonation requires considering where and when the people are, which radionuclide was used, and the layout of the obstacles (e.g., buildings, vegetation) in the path of the cloud.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2021

Mixed matrix membranes for post-combustion carbon capture: From materials design to membrane engineering

Mixed matrix materials (MMMs) containing nanofillers dispersed in continuous polymer matrices have emerged as an exciting and versatile platform to develop membranes with superior CO 2 /N 2 separation performance for post-combustion carbon capture. Both polymers and nanofillers can be vertically designed and engineered to combine the advantages of excellent processability (derived from polymers) and strong size-sieving ability or/and significant permanent porosity (originated from nanofillers). However, the MMMs face major challenges, such as interfacial incompatibility, particle agglomeration, and poor thin-film formability. This report provides a comprehensive yet critical review of various polymers and nanofillers (such as metal-organic frameworks, covalent organic frameworks, and two-dimensional materials) with promising CO 2 /N 2 separation properties. We exhaustively describe strategies to improve interfacial compatibility, such as in situ syntheses of polymers and nanofillers and functionalization of both components to improve adhesion. Moreover, we highlight various approaches to engineer the MMMs into thin-film composite (TFC) membranes. The review reveals the structure/property relationship in these MMMs and outlines the challenges and opportunities to realize their potential for practical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Multimode theory of electron hole transverse instability

We present Vlasov–Poisson three-dimensional linear stability analysis of an initially planar electron hole structure, solving for the distribution function by integration along unperturbed orbits. The non-sinusoidal potential perturbation shape (parallel to $B$ ) is expanded in eigenfunctions of the adiabatic Poisson operator, generalizing the prior assumption of a rigid shift of the equilibrium. We show that the shiftmode is then modified by a second discrete mode plus an integral over a continuum of wave-like modes. A rigorous treatment shows that the continuum can be approximated effectively by a single mode that satisfies the external wave dispersion relation, thus making the perturbation a weighted sum of three modes. We find numerically the solution for the complex instability frequency, and the corresponding three mode amplitudes determining the perturbation eigenmode. This multimode analysis refines the accuracy of the prior single-mode results, giving slightly higher growth rates at most parameters, as expected from the extra mode shape freedom. Oscillating modes near stability boundaries have larger mode distortions which help explain particle-in-cell simulations that observe instability up to ${\sim }20$ % beyond the prior shiftmode thresholds, and narrowing of the perturbation. At high magnetic field, the multimode analysis predicts a reduction of the already small growth rate.

Physics↗
DOE OSTI2021

Toward Å-fs-meV Resolution in Electron Microscopy: Systematic Simulation of the Temporal Spread of Single-Electron Packets

Though efforts to improve the temporal resolution of transmission electron microscopes (TEMs) have waxed and waned for decades, with relatively recent advances routinely reaching sub-picosecond scales, fundamental and practical challenges have hindered the advance of combined Å-fs-meV resolutions, particularly for core-loss spectroscopy and real-space imaging. This is due in no small part to the complexity of the approach required to access timescales upon which electrons, atoms, molecules, and materials first begin to respond and transform – attoseconds to picoseconds. Here we present part of a larger effort devoted to systematically mapping the instrument parameter space of a TEM modified to reach ultrafast timescales. With General Particle Tracer, we studied the statistical temporal distributions of single-electron packets as a function of various fs pulsed-laser parameters and electron-gun configurations and fields for the exact architecture and dimensions of a Thermo Fisher Tecnai Femto ultrafast electron microscope. We focused on easily-adjustable parameters, such as laser pulse duration, laser spot size, photon energy, Wehnelt aperture diameter, and photocathode size. In addition to establishing trends and dispersion behaviors, we identify regimes within which packet duration can be 100s of fs and approach the 300-fs laser limit employed here. Overall, the results provide a detailed picture of the temporal behavior of single-electron packets in the Tecnai Femto gun region, forming the initial contribution of a larger effort.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Metal–support interactions in metal oxide-supported atomic, cluster, and nanoparticle catalysis

Supported metal catalysts are essential to a plethora of processes in the chemical industry. The overall performance of these catalysts depends strongly on the interaction of adsorbates at the atomic level, which can be manipulated and controlled by the different constituents of the active material (i.e., support and active metal). The description of catalyst activity and the relationship between active constituent and the support, or metal–support interactions (MSI), in heterogeneous (thermo)catalysts is a complex phenomenon with multivariate (dependent and independent) contributions that are difficult to disentangle, both experimentally and theoretically. So-called “strong metal–support interactions” have been reported for several decades and summarized in excellent review articles. However, in recent years, there has been a proliferation of new findings related to atomically dispersed metal sites, metal oxide defects, and, for example, the generation and evolution of MSI under reaction conditions, which has led to the designation of (sub)classifications of MSI deserving to be critically and systematically evaluated. These include dynamic restructuring under alternating redox and reaction conditions, adsorbate-induced MSI, and evidence of strong interactions in oxide-supported metal oxide catalysts. Here, we review recent literature on MSI in oxide-supported metal particles to provide an up-to-date understanding of the underlying physicochemical principles that dominate the observed effects in supported metal atomic, cluster, and nanoparticle catalysts. Critical evaluation of different subclassifications of MSI is provided, along with discussions on the formation mechanisms, theoretical and characterization advances, and tuning strategies to manipulate catalytic reaction performance. We also provide a perspective on the future of the field, and we discuss the analysis of different MSI effects on catalysis quantitatively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Phonons, Q-dependent Kondo spin fluctuations, and 4f phonon resonance in YbAl 3

4f intermediate valence (IV) compounds are canonical hosts of correlated electron physics and can contribute to our understanding of the larger class of correlated electron materials. In this work, we study the prototype IV compound YbAl 3 which exhibits a nonintegral valence with a moderately heavy fermion ground state and a large Kondo temperature (T K ~500–600K). To better characterize the correlated physics of YbAl 3 , we have measured the phonon and the magnetic excitation spectra on single crystals of this material by time-of-flight inelastic neutron scattering and inelastic x-ray scattering. We have also performed theoretical calculations of the phonon spectra. We present three findings of these measurements. First, we observe that the measured phonon spectra can be described adequately by a calculation based on standard DFT+U density functional theory. The calculated energies, however, are 10% too low compared to the measured energies. This discrepancy may reflect a hardening of the phonons due to dynamic 4f correlations. Second, the low-temperature spin fluctuations on the Kondo energy scale k B T K have a momentum (Q) dependence similar to that seen recently in the IV compound CePd 3 . For that system, the Q dependence has been attributed to particle-hole excitations in a coherent itinerant 4f correlated ground state. We suggest a similar origin for the momentum dependence seen in YbAl 3 . This Q dependence disappears as the temperature is raised towards room temperature and the 4f electron band states become increasingly incoherent. Such a coherent/incoherent crossover is expected to be generic for correlated electron systems. Third, a low-temperature magnetic peak observed in the neutron scattering near 30 meV shows dispersion identical to a particular optic-phonon branch. This 4f/phonon resonance disappears for T≥150K. The phonon spectrum appears to be unaffected by the resonance. We discuss several possibilities for the origin of this unusual excitation, which may be unique to YbAl 3 . We suggest that the excitation may arise from the large amplitude beating of the light Al atoms against the heavy Yb atoms, resulting in a dynamic 4f/3p hybridization.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Evaporation and propagation of liquid drop streams at vacuum pressures: Experiments and modeling

Evaporation of streams of liquid droplets in environments at vacuum pressures below the vapor pressure has not been widely studied. Here, experiments and simulations are reported that quantify the change in droplet diameter when a steady stream of ≈100 μm diameter drops is injected into a chamber initially evacuated to <10 –8 bar. In experiments, droplets fall through the center of a 0.8 m long liquid nitrogen cooled shroud, simulating infinity radiation and vapor mass flux boundary conditions. Furthermore, experimentally measured changes in drop diameters vary from ≈0 to 6 μm when the initial vapor pressure is increased from 10 –6 to 10 –3 bar by heating the liquid. Measured diameter changes are predicted by a model based on the Hertz-Knudsen equation. One uncertainty in the calculation is the “sticking coefficient” β. Assuming a constant β for all conditions studied here, predicted diameter changes best match measurements with β≈0.3. This value falls within the range of β reported in the literature for organic liquids. Finally, at the higher vapor pressure conditions considered here, the drop stream disperses transverse to the main flow direction. This spread is attributed to forces imparted by an absolute pressure gradient produced by the evaporating stream.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

USING ER@CEBAF TO SHOW THAT A MULTIPASS ERL CAN DRIVE AN XFEL

A multi-pass recirculating superconducting CW linac offers a cost effective path to a multi-user facility with unprecedented scientific and industrial reach over a wide range of disciplines. We propose such a facility as an option for a potential UK-XFEL. Energy Recovery enables multi-MHz FEL sources, for example, an X-ray FEL oscillator or regenerative amplifier FEL. Additionally, combining with external lasers and/or self-interaction would provide access to MeV and GeV gamma-rays via inverse Compton scattering at high average power for nuclear and particle physics applications. An opportunity exists to demonstrate the necessary point-to-parallel longitudinal matches to drive an XFEL and successfully energy recover at the upcoming 5-pass up, 5-pass down Energy Recovery experiment on CEBAF at JLab termed ER@CEBAF. We show candidate matches and simulations supporting the minimal necessary modifications to CEBAF this will require. This includes linearisation of the longitudinal phase space in the injector and a reduction in the dispersion of the arcs, both of which increase the energy acceptance of CEBAF. We expect to commence initial tests of these adaptations on CEBAF during 2021.

Perez-Segurana, G.↗