Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLASTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1939

Tensile elastic properties of 18:8 chromium-nickel steel as affected by plastic deformation

The relationship between stress and strain, and between stress and permanent set, for 18:8 alloy as affected by prior plastic deformation is discussed. Hysteresis and creep and their effects on the stress-strain and stress-set curves are also considered, as well as the influence of duration of the rest interval after cold work and the influence of plastic deformation on proof stresses, on the modulus of elasticity at zero stress, and on the curvature of the stress-strain line. A constant (c sub 1) is suggested to represent the variation of the modulus of elasticity with stress.

Mcadam, D J↗
NASA NTRS1948

Determination of stresses in gas-turbine disks subjected to plastic flow and creep

A finite-difference method previously presented for computing elastic stresses in rotating disks is extended to include the computation of the disk stresses when plastic flow and creep are considered. A finite-difference method is employed to eliminate numerical integration and to permit nontechnical personnel to make the calculations with a minimum of engineering supervision. Illustrative examples are included to facilitate explanation of the procedure by carrying out the computations on a typical gas-turbine disk through a complete running cycle. The results of the numerical examples presented indicate that plastic flow markedly alters the elastic-stress distribution.

Millenson, M B↗
NASA NTRS1949

Plastic buckling of a rectangular plate under edge thrusts

The fundamental equations for the plastic buckling of a rectangular plate under edge thrusts are developed on the basis of a new set of stress-strain relations for the behavior of a metal in the plastic range. These relations are derived for buckling from a state of uniform compression. The fundamental equation for the buckling of a simply compressed plate together with typical boundary conditions is then developed and the results are applied to calculating the buckling loads of a thin strip, a simply supported plate, and a cruciform section. Comparisons with the theories of Timoshenko and Ilyushin are made. Finally, an energy method is given which can be used for finding approximate values of the critical load.

Handelman, G H↗
NASA NTRS1951

Analysis of plane-plastic stress problems with axial symmetry in strain-hardening range

A simple method is developed for solving plane-plastic-stress problems with axial symmetry in the strain-hardening range which is based on the deformation theory of plasticity employing the finite-strain concept. The equations defining the problems are first reduced to two simultaneous nonlinear differential equations involving two dependent variables: (a) the octahedral shear strain, and (b) a parameter indicating the ratio of principal stresses. By multiplying the load and dividing the radius by an arbitrary constant, it is possible to solve these problems without iteration for any value of the modified load. The constant is determined by the boundary condition. This method is applied to a circular membrane under pressure, a rotating disk without and with a central hole, and an infinite plate with a circular hole. Two materials, inconel x and 16-25-6, the octahedral shear stress-strain relations of which do not follow the power law, are used. Distributions of octahedral shear strain, as well as of principal stresses and strains, are obtained. These results are compared with the results of the same problems in the elastic range.

Wu, M H Lee↗
NASA NTRS1956

Plastic Deformation of Aluminum Single Crystals at Elevated Temperatures

This report describes the results of a comprehensive study of plastic deformation of aluminum single crystals over a wide range of temperatures. The results of constant-stress creep tests have been reported for the temperature range from 400 degrees to 900 degrees F. For these tests, a new capacitance-type extensometer was designed. This unit has a range of 0.30 inch over which the sensitivity is very nearly linear and can be varied from as low a sensitivity as is desired to a maximum of 20 microinches per millivolt with good stability. Experiments were carried out to investigate the effect of small amounts of prestraining, by two different methods, on the creep and tensile properties of these aluminum single crystals. From observations it has been concluded that plastic deformation takes place predominantly by slip which is accompanied by the mechanisms of kinking and polygonization.

Johnson, R D↗
NASA NTRS1993

Elastic plastic fracture mechanics methodology for surface cracks

The Elastic Plastic Fracture Mechanics (EPFM) Methodology has evolved significantly in the last several years. Nevertheless, some of these concepts need to be extended further before the whole methodology can be safely applied to structural parts. Specifically, there is a need to include the effect of constraint in the characterization of material resistance to crack growth and also to extend these methods to the case of 3D defects. As a consequence, this project was started as a 36 month research program with the general objective of developing an EPFM methodology to assess the structural reliability of pressure vessels and other parts of interest to NASA containing defects. This report covers a computer modelling algorithm used to simulate the growth of a semi-elliptical surface crack; the presentation of a finite element investigation that compared the theoretical (HRR) stress field to that produced by elastic and elastic-plastic models; and experimental efforts to characterize three dimensional aspects of fracture present in 'two dimensional', or planar configuration specimens.

Ernst, Hugo A.↗
NASA NTRS1994

Elastic plastic fracture mechanics methodology for surface cracks

The Elastic Plastic Fracture Mechanics Methodology has evolved significantly in the last several years. Nevertheless, some of these concepts need to be extended further before the whole methodology can be safely applied to structural parts. Specifically, there is a need to include the effect of constraint in the characterization of material resistance to crack growth and also to extend these methods to the case of 3D defects. As a consequence, this project was started as a 36 month research program with the general objective of developing an elastic plastic fracture mechanics methodology to assess the structural reliability of pressure vessels and other parts of interest to NASA which may contain flaws. The project is divided into three tasks that deal with (1) constraint and thickness effects, (2) three-dimensional cracks, and (3) the Leak-Before-Burst (LBB) criterion. This report period (March 1994 to August 1994) is a continuation of attempts to characterize three dimensional aspects of fracture present in 'two dimensional' or planar configuration specimens (Chapter Two), especially, the determination of, and use of, crack face separation data. Also, included, are a variety of fracture resistance testing results (J(m)R-curve format) and a discussion regarding two materials of NASA interest (6061-T651 Aluminum alloy and 1N718-STA1 nickel-base super alloy) involving a bases for like constraint in terms of ligament dimensions, and their comparison to the resulting J(m)R-curves (Chapter Two).

Ernst, Hugo A.↗
NASA NTRS1994

The load separation technique in the elastic-plastic fracture analysis of two- and three-dimensional geometries

Load separation is the representation of the load in the test records of geometries containing cracks as a multiplication of two separate functions: a crack geometry function and a material deformation function. Load separation is demonstrated in the test records of several two-dimensional geometries such as compact tension geometry, single edge notched bend geometry, and center cracked tension geometry and three-dimensional geometries such as semi-elliptical surface crack. The role of load separation in the evaluation of the fracture parameter J-integral and the associated factor eta for two-dimensional geometries is discussed. The paper also discusses the theoretical basis and the procedure for using load separation as a simplified yet accurate approach for plastic J evaluation in semi-elliptical surface crack which is a three-dimensional geometry. The experimental evaluation of J, and particularly J(sub pl), for three-dimensional geometries is very challenging. A few approaches have been developed in this regard and they are either complex or very approximate. The paper also presents the load separation as a mean to identify the blunting and crack growth regions in the experimental test records of precracked specimens. Finally, load separation as a methodology in elastic-plastic fracture mechanics is presented.

Sharobeam, Monir H.↗
NASA NTRS1995

JTEC monograph on biodegradable polymers and plastics in Japan: Research, development, and applications

A fact-finding team of American scientists and engineers visited Japan to assess the status of research and development and applications in biodegradable polymers. The visit was sponsored by the National Science Foundation and industry. In Japan, the team met with representatives of 31 universities, government ministries and institutes, companies, and associations. Japan's national program on biodegradable polymers and plastics evaluates new technologies, testing methods, and potential markets for biodegradables. The program is coordinated by the Biodegradable Plastics Society of Japan, which seeks to achieve world leadership in biodegradable polymer technology and identify commercial opportunities for exploiting this technology. The team saw no major new technology breakthroughs. Japanese scientists and engineers are focusing on natural polymers from renewable resources, synthetic polymers, and bacterially-produced polymers such as polyhydroxyalkanoates, poly(amino acids), and polysaccharides. The major polymers receiving attention are the Zeneca PHBV copolymers, Biopol(registered trademark), poly(lactic acid) from several sources, polycaprolactone, and the new synthetic polyester, Bionolle(registered trademark), from Showa High Polymer. In their present state of development, these polymers all have major deficiencies that inhibit their acceptance for large-scale applications.

Lenz, Robert W.↗
NASA NTRS1995

Automatic Inspection Of Heat Seals Between Plastic Sheets

Automatic inspection apparatus detects flaws in heat seals between films of polyethylene or other thermoplastic material. Heat-sealed strip in multilayer plastic sheet continuously moved lengthwise over illuminators. Variations in light transmitted through sheet interpreted to find flaws in heat seal. Site of flaw marked to facilitate subsequent manual inspection. Heat sealing used to join plastic films in manufacturing of variety of products, including inflatable toys and balloons carrying scientific instruments to high altitudes.

Rai, Kula R.↗
NASA NTRS1997

Parallel adaptive mesh refinement techniques for plasticity problems

The accurate modeling of the nonlinear properties of materials can be computationally expensive. Parallel computing offers an attractive way for solving such problems; however, the efficient use of these systems requires the vertical integration of a number of very different software components, we explore the solution of two- and three-dimensional, small-strain plasticity problems. We consider a finite-element formulation of the problem with adaptive refinement of an unstructured mesh to accurately model plastic transition zones. We present a framework for the parallel implementation of such complex algorithms. This framework, using libraries from the SUMAA3d project, allows a user to build a parallel finite-element application without writing any parallel code. To demonstrate the effectiveness of this approach on widely varying parallel architectures, we present experimental results from an IBM SP parallel computer and an ATM-connected network of Sun UltraSparc workstations. The results detail the parallel performance of the computational phases of the application during the process while the material is incrementally loaded.

Barry, W. J.↗
NASA NTRS1998

An Evaluation of the Plasticity-Induced Crack-Closure Concept and Measurement Methods

An assessment of the plasticity-induced crack-closure concept is made, in light of some of the questions that have been raised on the validity of the concept, and the assumptions that have been made concerning crack-dp damage below the crack-opening stress. The impact of using other crack-tip parameters, such as the cyclic crack-tip displacement, to model crack-growth rate behavior was studied. Crack-growth simulations, using a crack-closure model, showed a close relation between traditional Delta K eff, and the cyclic crack-tip displacement (Delta eff) for an aluminum alloy and a steel. Evaluations of the cyclic hysteresis energy demonstrated that the cyclic plastic damage below the crack-opening stress was negligible in the Paris crack-growth regime. Some of the standard and newly proposed remote measurement methods to determine the 'effective' crack-tip driving parameter were evaluated on middle-crack tension specimens. A potential source of the Kmax effect on crack-growth rates was studied on an aluminum alloy. Results showed that the ratio of Kmax to Kc had a strong effect on crack-growth rates at high stress ratios and at low stress ratios for very high stress levels. The crack-closure concept and the traditional crack-growth rate equations were able to correlate and predict crack-growth rates under these extreme conditions.

Newman, James C., Jr.↗
NASA NTRS1999

Crack Growth Prediction Methodology for Multi-Site Damage: Layered Analysis and Growth During Plasticity

A finite element program has been developed to perform quasi-static, elastic-plastic crack growth simulations. The model provides a general framework for mixed-mode I/II elastic-plastic fracture analysis using small strain assumptions and plane stress, plane strain, and axisymmetric finite elements. Cracks are modeled explicitly in the mesh. As the cracks propagate, automatic remeshing algorithms delete the mesh local to the crack tip, extend the crack, and build a new mesh around the new tip. State variable mapping algorithms transfer stresses and displacements from the old mesh to the new mesh. The von Mises material model is implemented in the context of a non-linear Newton solution scheme. The fracture criterion is the critical crack tip opening displacement, and crack direction is predicted by the maximum tensile stress criterion at the crack tip. The implementation can accommodate multiple curving and interacting cracks. An additional fracture algorithm based on nodal release can be used to simulate fracture along a horizontal plane of symmetry. A core of plane strain elements can be used with the nodal release algorithm to simulate the triaxial state of stress near the crack tip. Verification and validation studies compare analysis results with experimental data and published three-dimensional analysis results. Fracture predictions using nodal release for compact tension, middle-crack tension, and multi-site damage test specimens produced accurate results for residual strength and link-up loads. Curving crack predictions using remeshing/mapping were compared with experimental data for an Arcan mixed-mode specimen. Loading angles from 0 degrees to 90 degrees were analyzed. The maximum tensile stress criterion was able to predict the crack direction and path for all loading angles in which the material failed in tension. Residual strength was also accurately predicted for these cases.

James, Mark Anthony↗
NASA NTRS1994

Dynamic Load Balancing for Computational Plasticity on Parallel Computers

The simulation of the computational plasticity on a complex structure remains a formidable computational task, especially when a highly nonlinear, complex material model was used. It appears that the computational requirements for a such problem can only be satisfied by massively parallel architectures. In order to effectively harness the tremendous computational power provided by such architectures, it is imperative to investigate and to study the algorithmic and implementation issues pertaining to dynamic load balancing for computational plasticity on a highly parallel, distributed-memory, multiple-instruction, multiple-data computers. This paper will measure the effectiveness of the algorithms developed in handling the dynamic load balancing.

Pramono, Eddy↗
NASA NTRS1994

Mammalian Vestibular Macular Synaptic Plasticity: Results from SLS-2 Spaceflight

The effects of exposure to microgravity were studied in rat utricular maculas collected inflight (IF, day 13), post-flight on day of orbiter landing (day 14, R+O) and after 14 days (R+ML). Controls were collected at corresponding times. The objectives were 1) to learn whether hair cell ribbon synapses counts would be higher in tissues collected in space than in tissues collected postflight during or after readaptation to Earth's gravity; and 2) to compare results with those of SLS-1. Maculas were fixed by immersion, micro-dissected, dehydrated and prepared for ultrastructural study by usual methods. Synapses were counted in 100 serial sections 150 nm thick and were located to specific hair cells in montages of every 7th section. Counts were analyzed for statistical significance using analysis of variance. Results in maculas of IF dissected rats, one 13 day control (IFC), and one R + 0 rat have been analyzed. Study of an R+ML macula is nearly completed. For type I cells, IF mean is 2.3 +/-1.6; IFC mean is 1.6 +/-1.0; R+O mean is 2.3 +/- 1.6. For type II cells, IF mean is 11.4 +/- 17.1; IFC mean is 5.5 +/-3.5; R+O mean is 10.1 +/- 7.4. The difference between IF and IFC means for type I cells is statistically significant (p less than 0.0464). For type It cells, IF compared to IFC means, p less than 0.0003; and for IFC to R+O means, p less than 0.0139. Shifts toward spheres (p less than 0.0001) and pairs (p less than 0.0139) were significant in type II cells of IF rats. The results are largely replicating findings from SLS-1 and indicate that spaceflight affects synaptic number, form and distribution, particularly in type II hair cells. The increases in synaptic number and in sphere-like ribbons are interpreted to improve synaptic efficacy, to help return afferent discharges to a more normal state. Findings indicate that a great capacity for synaptic plasticity exists in mammalian gravity sensors, and that this plasticity is more dominant in the local circuitry. The local circuit includes type II cells and is interpreted to be responsible for shaping the final output of the system.

Ross, Muriel D.D.↗
NASA NTRS1996

Synaptic Plasticity In Mammalian Gravity Sensors: Preliminary Results From SLS-2

Sensory conflict is the prevalent theoretical explanation for space adaptation syndrome. This ultrastructural study tests the hypothesis that peripheral gravity sensors (maculae) play a role. Results were obtained from the medial part of utricular maculae of adult rats exposed to microgravity for 14 days, and from controls. Means and statistical significance of synapse counts were calculated using SUPERANOVA(Trademark) and Scheffe's procedure for post-hoc comparisons. Preliminary findings are from 2 sets of 100 serial sections for each dataset. Synapses were doubled numerically in type II hair cells of utricular maculae collected on day 13 inflight compared to controls (11.4 +/- 7.1 vs. 5.3 +/- 3.8; p < 0.0001). Flight mean synaptic number declined rapidly postflight and became comparable to means of controls. Synapses also increased numerically in type I cells inflight (2.4 +/- 1.6 vs. 1.7 +/- 1.0; p < 0.0341). Postflight there were no significant differences in counts. Results concerning shifts in ribbon type and distribution are also largely replicating previous findings from flight studies. Results indicate that mammalian maculae are adaptive endorgans that retain the property of synaptic plasticity into the adult stage. Macular plasticity has clinical implications for balance disorders of peripheral origin.

Ross, M. D.↗
NASA NTRS2003

Ribbon Synaptic Plasticity in Gravity Sensors of Rats Flown on Neurolab

Previous spaceflight experiments (Space Life Sciences-1 and -2 (SLS-1 and SLS-2)) first demonstrated the extraordinary ability of gravity sensor hair cells to change the number, kind, and distribution of connections (synapses) they make to other cells while in weightlessness. The number of synapses in hair cells in one part of the inner ear (the utricle) was markedly elevated on flight day 13 (FD13) of SLS-2. Unanswered questions, however, were whether these increases in synapses occur rapidly and whether they remain stable in weightlessness. The answers have implications for long-duration human space travel. If gravity sensors can adapt quickly, crews may be able to move easily between different gravity levels, since the sensors will adapt rapidly to weightlessness on the spacecraft and then back to Earth's gravity when the mission ends. This ability to adapt is also important for recovery from balance disorders. To further our understanding of this adaptive potential (a property called neuronal synaptic plasticity), the present Neurolab research was undertaken. Our experiment examined whether: (a) increases in synapses would remain stable throughout the flight, (b) changes in the number of synapses were uniform across different portions of the gravity sensors (the utricle and saccule), and (c) synaptic changes were similar for the different types of hair cells (Type I and Type II). Utricular and saccular maculae (the gravity-sensing portions of the inner ear) were collected in flight from rats on FD2 and FD14. Samples were also collected from control rats on the ground. Tissues were prepared for ultrastructural study. Hair cells and their ribbon synapses were examined in a transmission electron microscope. Synapses were counted in all hair cells in 50 consecutive sections that crossed the striolar zone. Results indicate that utricular hair cell synapses initially increased significantly in number in both types of hair cells by FD2. Counts declined by FD14, but the mean number of synapses in utricular Type II cells remained significantly higher than in the ground control rats. For saccular samples, synaptic number in Type I and Type II cells declined on FD2, but returned to near-baseline values by FD14. These findings indicate that: (a) synaptic plasticity occurs rapidly in weightlessness, and (b) synaptic changes are not identical for the two types of hair cells or for the two maculae.

Ross, Muriel D.↗
NASA NTRS2000

Plasticity and Kinky Chemistry of Carbon Nanotubes

Since their discovery in 1991, carbon nanotubes have been the subject of intense research interest based on early predictions of their unique mechanical, electronic, and chemical properties. Materials with the predicted unique properties of carbon nanotubes are of great interest for use in future generations of aerospace vehicles. For their structural properties, carbon nanotubes could be used as reinforcing fibers in ultralight multifunctional composites. For their electronic properties, carbon nanotubes offer the potential of very high-speed, low-power computing elements, high-density data storage, and unique sensors. In a continuing effort to model and predict the properties of carbon nanotubes, Ames accomplished three significant results during FY99. First, accurate values of the nanomechanics and plasticity of carbon nanotubes based on quantum molecular dynamics simulations were computed. Second, the concept of mechanical deformation catalyzed-kinky-chemistry as a means to control local chemistry of nanotubes was discovered. Third, the ease of nano-indentation of silicon surfaces with carbon nanotubes was established. The elastic response and plastic failure mechanisms of single-wall nanotubes were investigated by means of quantum molecular dynamics simulations.

Srivastava, Deepak↗