Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Normal modes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Intelligent (Autonomous) Power Controller Development for Human Deep Space Exploration

As NASAs Evolvable Mars Campaign and other exploration initiatives continue to mature they have identified the need for more autonomous operations of the power system. For current human space operations such as the International Space Station, the paradigm is to perform the planning, operation and fault diagnosis from the ground. However, the dual problems of communication lag as well as limited communication bandwidth beyond GEO synchronous orbit, underscore the need to change the operation methodology for human operation in deep space. To address this need, for the past several years the Glenn Research Center has had an effort to develop an autonomous power controller for human deep space vehicles. This presentation discusses the present roadmap for deep space exploration along with a description of conceptual power system architecture for exploration modules. It then contrasts the present ground centric control and management architecture with limited autonomy on-board the spacecraft with an advanced autonomous power control system that features ground based monitoring with a spacecraft mission manager with autonomous control of all core systems, including power. It then presents a functional breakdown of the autonomous power control system and examines its operation in both normal and fault modes. Finally, it discusses progress made in the development of a real-time power system model and how it is being used to evaluate the performance of the controller and well as using it for verification of the overall operation.

Power Systems↗
NASA NTRS2018

Low-Noise Operating Mode for Propeller-Driven Electric Airplanes

Mechanical shaft power and shaft speed of reciprocating internal combustion engines are closely coupled. Maximum rated shaft power is typically produced at or near peak shaft speed. If a general aviation airplane equipped with a reciprocating engine and a variable-pitch propeller attempts a low-noise takeoff by reducing propeller tip speed, propeller power and thrust are reduced. Such takeoffs are not tolerated due to punishing performance effects, such as increased field lengths and poor climb rates. Certain electric motors, however, are able to deliver maximum shaft power over a wide range of shaft speed. Electric or hybrid-electric propeller-driven airplanes should be able to exploit this behavior. At low shaft speeds, high shaft power levels and high blade pitch angles could be combined to recover much of the thrust that would otherwise be lost. This could enable a low-noise operating mode for propellers normally designed for performance rather than for noise. The subject of this paper is an analytical investigation into low-noise takeoffs and steady overflights of a notional general aviation airplane equipped with a propeller driven by an electric motor.

Berton, Jeffrey J.↗
NASA NTRS1999

East Asian Summer Monsoon Rainfall: A Historical Perspective of the 1998 Flood over Yangtze River

One of the main factors that might have caused the disastrous flood in China during 1998 summer is long-term variations that include a trend indicating increasing monsoon rainfall over the Yangtze River Valley. China's 160-station monthly rainfall anomaly for the summers of 1955-98 is analyzed for exploring such long-term variations. Singular value decomposition (SVD) between the summer rainfall and the global sea surface temperature (SST) anomalies reveals that the rainfall over Yangtze River Valley is closely related to global and regional SST variabilities at both interannual and interdecadal timescales. SVD1 mode links the above normal rainfall condition in central China to an El Nino-like SSTA distribution, varying on interannual timescale modified by a trend during the period. SVD3 mode links positive rainfall anomaly in Yangtze River Valley to the warm SST anomaly in the subtropical western Pacific, varying on interannual timescales modified by interdecadal timescales. This link tends to be stronger when the Nino3 area becomes colder and the western subtropical Pacific becomes warmer. The 1998 summer is a transition season when the 1997/98 El Nino event was in its decaying phase, and the SST in the Nino3 area emerged below normal anomaly while the subtropical western Pacific SST above normal. Thus, the first and third SVD modes become dominant in 1998 summer, favoring more Asian summer monsoon rainfall over the Yangtze River Valley.

Weng, H.-Y.↗
NASA NTRS1988

Microstructural effects on fracture toughness of polycrystalline ceramics in combined mode I and mode II loading

Fracture toughness of polycrystalline alumina and ceria partially-stabilized tetragonal zirconia (CeO2-TZP) ceramics were assessed in combined mode I and mode II loading using precracked disk specimens in diametral compression. Stress states ranging from pure mode I, combined mode I and mode II, and pure mode II were obtained by aligning the center crack at specific angles relative to the loading diameter. The resulting mixed-mode fracture toughness envelope showed significant deviation to higher fracture toughness in mode II relative to the predictions of the linear elastic fracture mechanics theory. Critical comparison with corresponding results on soda-lime glass and fracture surface observations showed that crack surface resistance arising from grain interlocking and abrasion was the main source of the increased fracture toughness in mode II loading of the polycrystalline ceramics. The normalized fracture toughness for pure mode II loading, (KII/KIc), increased with increasing grain size for the CeO2-TZP ceramics. Quantitative fractography confirmed an increased percentage of transgranular fracture of the grains in mode II loading.

Singh, D.↗
NASA NTRS2011

Advanced Electrocardiography Can Identify Occult Cardiomyopathy in Doberman Pinschers

Recently, multiple advanced resting electrocardiographic (A-ECG) techniques have improved the diagnostic value of short-duration ECG in detection of dilated cardiomyopathy (DCM) in humans. This study investigated whether 12-lead A-ECG recordings could accurately identify the occult phase of DCM in dogs. Short-duration (3-5 min) high-fidelity 12-lead ECG recordings were obtained from 31 privately-owned, clinically healthy Doberman Pinschers (5.4 +/- 1.7 years, 11/20 males/females). Dogs were divided into 2 groups: 1) 19 healthy dogs with normal echocardiographic M-mode measurements: left ventricular internal diameter in diastole (LVIDd . 47mm) and in systole (LVIDs . 38mm) and normal 24-hour ECG recordings (<50 ventricular premature complexes, VPCs); and 2) 12 dogs with occult DCM: 11/12 dogs had increased M-mode measurements (LVIDd . 49mm and/or LVIDs . 40mm) and 5/11 dogs had also >100 VPCs/24h; 1/12 dogs had only abnormal 24-hour ECG recordings (>100 VPCs/24h). ECG recordings were evaluated via custom software programs to calculate multiple parameters of high-frequency (HF) QRS ECG, heart rate variability, QT variability, waveform complexity and 3-D ECG. Student's t-tests determined 19 ECG parameters that were significantly different (P < 0.05) between groups. Principal component factor analysis identified a 5-factor model with 81.4% explained variance. QRS dipolar and non-dipolar voltages, Cornell voltage criteria and QRS waveform residuum were increased significantly (P < 0.05), whereas mean HF QRS amplitude was decreased significantly (P < 0.05) in dogs with occult DCM. For the 5 selected parameters the prediction of occult DCM was performed using a binary logistic regression model with Chi-square tested significance (P < 0.01). ROC analyses showed that the five selected ECG parameters could identify occult ECG with sensitivity 89% and specificity 83%. Results suggest that 12-lead A-ECG might improve diagnostic value of short-duration ECG in earlier detection of canine DCM as five selected ECG parameters can with reasonable accuracy identify occult DCM in Doberman Pinschers. Future extensive clinical studies need to clarify if 12-lead A-ECG could be useful as an additional screening test for canine DCM.

Spiljak, M.↗
NASA NTRS1993

System for determining the angle of impact of an object on a structure

A method for determining the angle of impact of an object on a thin-walled structure which determines the angle of impact through analysis of the acoustic waves which result when an object impacts a structure is presented. Transducers are placed on and in the surface of the structure which sense the wave caused in the structure by impact. The waves are recorded and saved for analysis. For source motion normal to the surface, the antisymmetric mode has a large amplitude while that of the symmetric mode is very small. As the source angle increases with respect to the surface normal, the symmetric mode amplitude increases while the antisymmetric mode amplitude decreases. Thus, the angle of impact is determined by measuring the relative amplitudes of these two lowest order modes.

Prosser, William H.↗
NASA NTRS2011

Space Environments Testbed

The Space Environments Testbed (SET) is a flight controller data system for the Common Carrier Assembly. The SET-1 flight software provides the command, telemetry, and experiment control to ground operators for the SET-1 mission. Modes of operation (see dia gram) include: a) Boot Mode that is initiated at application of power to the processor card, and runs memory diagnostics. It may be entered via ground command or autonomously based upon fault detection. b) Maintenance Mode that allows for limited carrier health monitoring, including power telemetry monitoring on a non-interference basis. c) Safe Mode is a predefined, minimum power safehold configuration with power to experiments removed and carrier functionality minimized. It is used to troubleshoot problems that occur during flight. d) Operations Mode is used for normal experiment carrier operations. It may be entered only via ground command from Safe Mode.

Leucht, David K.↗
NASA NTRS1995

Rectangular Waveguides with Two Conventional and Two Superconducting Walls

The propagation properties of transverse electric TE(sup pm) modes and their dispersion relations in rectangular waveguides with two conventional and two superconducting walls, derived by using the Meissner boundary conditions on the superconducting walls, are presented. In addition to recovering some previously known results, some novel results have been obtained: the cut-off wavelength of the dominant TE(sup 10) mode is greater than that of the conventional TE(sub 10) mode, and the tangential electric field and normal magnetic field for the dominant mode TE(sup 10) exist on the superconducting surfaces. Expressions for electromagnetic components, surface currents, attenuation coefficient, maximum transmitted power, dispersion and wave impedance are also presented.

Yalamanchili, Raj↗
NASA NTRS1979

Experimental investigation of dynamic characteristics of turbine generators and low-tuned foundations

Turbine generator (T-G) units with low tuned concrete foundations were investigated experimentally during both startup and normal operating conditions. The dynamic response of the turbine generators and their foundation systems were characterized by resonance curves obtained during the startup transient and by vibration mode shapes at the normal operating condition. No severe resonance at the fundamental frequencies of the system was observed. The deflection or displacement of the foundation pedestal does not lead to unacceptable T-G vibration. The experimental results are compared and discussed with some previous theoretical studies.

Ying, S. P.↗
NASA NTRS2001

Secondary metabolism in simulated microgravity

We have studied microbial secondary metabolism in a simulated microgravity (SMG) environment provided by NASA rotating-wall bioreactors (RWBs). These reactors were designed to simulate some aspects of actual microgravity that occur in space. Growth and product formation were observed in SMG in all cases studied, i.e., Bacillus brevis produced gramicidin S (GS), Streptomyces clavuligerus made beta-lactam antibiotics, Streptomyces hygroscopicus produced rapamycin, and Escherichia coli produced microcin B17 (MccB17). Of these processes, only GS production was unaffected by SMG; production of the other three products was inhibited. This was determined by comparison with performance in an RWB positioned in a different mode to provide a normal gravity (NG) environment. Carbon source repression by glycerol of the GS process, as observed in shaken flasks, was not observed in the RWBs, whether operated in the SMG or NG mode. The same phenomenon occurred in the case of MccB17 production, with respect to glucose repression. Thus, the negative effects of carbon source on GS and beta-lactam formation are presumably dependent on shear, turbulence, and/or vessel geometry, but not on gravity. Stimulatory effects of phosphate and the precursor L-lysine on beta-lactam antibiotic production, as observed in flasks, also occurred in SMG. An almost complete shift in the localization of produced MccB17 from cells to extracellular medium was observed when E. coli was grown in the RWB under SMG or NG. If a plastic bead was placed in the RWB, accumulation became cellular, as it is in shaken flasks, indicating that sheer stress favors a cellular location. In the case of rapamycin, the same type of shift was observed, but it was less dramatic, i.e., growth in the RWB under SMG shifted the distribution of produced rapamycin from 2/3 cellular:1/3 extracellular to 1/3 cellular:2/3 extracellular. Stress has been shown to induce or promote secondary metabolism in a number of other microbial systems. RWBs provide a low stress SMG environment, which, however, supports only poor production of MccB17, as compared to production in shaken flasks. We wondered whether the poor production in RWBs under SMG is due to the low level of stress, and whether increasing stress in the RWBs would raise the amount of MccB17 formed. We found that increasing shear stress by adding a single Teflon bead to the RWB improved MccB17 production. Although shear stress seems to have a marked positive effect on MccB17 production in SMG, addition of various concentrations of ethanol to RWBs (or to shaken flasks) failed to increase MccB17 production. Ethanol stress merely decreased production and, at higher concentrations, inhibited growth. Interestingly, cells growing in the RWB were much more resistant to the growth- and production-inhibitory effects of ethanol than cells growing in shaken flasks. With respect to S. hygroscopicus, addition of Teflon beads to the RWB reversed the inhibition of growth, but rapamycin production was still markedly inhibited, and the distribution did not revert back to a preferential cellular site.

NASA Discipline Cell Biology↗
NASA NTRS1989

Aircraft modal supression system: Existing design approach and its shortcomings

The bending of flexible body aircraft may degrade the ride coMfort of passengers. This is especially noticeable towards the aft end of the aircraft (due to the relatively large tail surfaces) which may easily be excited when flying through turbulence. In addition, some aircraft may experience a front body bending mode which can be annoying to the cabin crew and first class passengers. Normally, this dominant body bending mode falls between 1 to 5 Hz. This range is easily perceived by the human body. Also, in some situations, the rigid body control law may be out of phase with the mode and aggravate the vibration. Hence, an active modal suppression system is desirable for improving the ride quality of the airplane. The size of the mathematical model, which has both the airplane rigid body and flexible characteristics, could easily exceed 100 states. The computational burden and fidelity of this large structural model is addressed.

Ho, J. K.↗
NASA NTRS1972

Mechanical systems readiness assessment and performance monitoring study

The problem of mechanical devices which lack the real-time readiness assessment and performance monitoring capability required for future space missions is studied. The results of a test program to establish the feasibility of implementing structure borne acoustics, a nondestructive test technique, are described. The program included the monitoring of operational acoustic signatures of five separate mechanical components, each possessing distinct sound characteristics. Acoustic signatures were established for normal operation of each component. Critical failure modes were then inserted into the test components, and faulted acoustic signatures obtained. Predominant features of the sound signature were related back to operational events occurring within the components both for normal and failure mode operations. All of these steps can be automated. The structure borne acoustics technique lends itself to reducing checkout time, simplifying maintenance procedures, and reducing manual involvement in the checkout, operation, maintenance, and fault diagnosis of mechanical systems.

Source record↗
NASA NTRS1977

Characterization of crack growth under combined loading

Room-temperature static and cyclic tests were made on 21 aluminum plates in the shape of a 91.4x91.4-cm Maltese cross with 45 deg flaws to develop crack growth and fracture toughness data under mixed-mode conditions. During cyclic testing, it was impossible to maintain a high proportion of shear-mode deformation on the crack tips. Cracks either branched or turned. Under static loading, cracks remained straight if shear stress intensity exceeded normal stress intensity. Mixed-mode crack growth rate data compared reasonably well with published single-mode data, and measured crack displacements agreed with the straight and branched crack analyses. Values of critical strain energy release rate at fracture for pure shear were approximately 50% higher than for pure normal opening, and there was a large reduction in normal stress intensity at fracture in the presence of high shear stress intensity. Net section stresses were well into the inelastic range when fracture occurred under high shear on the cracks.

Feldman, A.↗
NASA NTRS1974

Self-teaching digital-computer program for fail-operational control of a turbojet engine in a sea-level test stand

The design and evaluation are described of a digital turbojet engine control which is capable of sensing catastrophic failures in either the engine rotor speed or the compressor discharge static-pressure signal and is capable of switching control modes to maintain near normal operation. The control program was developed for and tested on a turbojet engine located in a sea-level test stand. The control program is also capable of acquiring all the data that are necessary for the fail-operational control to function.

Wallhagen, R. E.↗
NASA NTRS1974

Mixed mode stress intensity factors for semielliptical surface cracks

The three-dimensional equations of elasticity are solved for a flat elliptical crack which has nonuniform shear stresses applied to its surfaces. An alternating method is used to determine the mode two and mode three stress intensity factors for a semielliptical surface crack in the surface of a finite thickness solid. These stress intensity factors are presented as a function of position along the crack border for a number of crack shapes and crack depths. This same technique is followed to determine the mode one stress intensity factors for the semielliptical surface crack which has normal loading applied to its surface. Mode one stress intensity factors are presented and compared with the results obtained from previous work.

Smith, F. W.↗
NASA NTRS1983

Large-amplitude hydromagnetic waves in collisionless relativistic plasma - Exact solution for the fast-mode magnetoacoustic wave

An exact nonlinear solution is found to the relativistic kinetic and electrodynamic equations (in their hydromagnetic limit) that describes the large-amplitude fast-mode magnetoacoustic wave propagating normal to the magnetic field in a collisionless, previously uniform plasma. It is pointed out that a wave of this kind will be generated by transverse compression of any collisionless plasma. The solution is in essence independent of the detailed form of the particle momentum distribution functions. The solution is obtained, in part, through the method of characteristics; the wave exhibits the familiar properties of steepening and shock formation. A detailed analysis is given of the ultrarelativistic limit of this wave.

Barnes, A.↗