Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Milling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Protein Extraction, Precipitation, and Recovery from Chlorella sorokiniana Using Mechanochemical Methods

Protein extraction, precipitation, and recovery methods were evaluated by this study using a green alga—Chlorella sorokiniana. A mechanochemical cell disruption process was applied to facilitate protein extraction from microalgal biomass. Optimization of the mechanochemical process resulted in milling conditions that achieved a protein extraction of 52.7 ± 6.45%. The consequent acid precipitation method was optimized to recover 98.7% of proteins from the microalgal slurry. The measured protein content of the protein isolate was 41.4% w/w. These results indicate that the precipitation method is successful at recovering the extracted proteins in the algal slurry; however, the removal of non-protein solids during centrifugation and pH adjustment is not complete. The energy balance analysis elucidated that the energy demand of the protein extraction and recovery operation, at 0.83 MJ/kg dry algal biomass, is much lower than previous studies using high-pressure homogenization and membrane filtration. This study concludes that mechanochemical protein extraction and recovery is an effective, low-energy processing method, which could be used by algal biorefineries to prepare algal proteins for value-added chemical production as well as to make algal carbohydrates and lipids in the residual biomass more accessible for biofuel production.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Stability Evaluation for a Damped, Constrained-Motion Cutting Force Dynamometer

This paper describes the dynamic stability evaluation of a constrained-motion dynamometer (CMD) with passive damping. The CMD’s flexure-based design offers an alternative to traditional piezoelectric cutting force dynamometers, which can exhibit adverse effects of the complex structural dynamics on the measurement accuracy. In contrast, the CMD system’s structural dynamics are nominally single degree of freedom and are conveniently altered by material selection, flexure element geometry, and element arrangement. In this research, a passive damping approach is applied to increase the viscous damping ratio and, subsequently, the stability limit. Cutting tests were completed and the in situ CMD displacement and velocity signals were sampled at the spindle rotating frequency. The periodic sampling approach was used to determine if the milling response was synchronous with the spindle rotation (stable) or not (chatter) by constructing Poincaré maps for both experiment and prediction (time-domain simulation). It was found that the viscous damping coefficient was increased by 130% and the critical stability limit was increased from 4.3 mm (no damping) to 15.4 mm (with damping).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Abrasive Waterjet Machining

The abrasive waterjet machining process was introduced in the 1980s as a new cutting tool; the process has the ability to cut almost any material. Currently, the AWJ process is used in many world-class factories, producing parts for use in daily life. A description of this process and its influencing parameters are first presented in this paper, along with process models for the AWJ tool itself and also for the jet–material interaction. The AWJ material removal process occurs through the high-velocity impact of abrasive particles, whose tips micromachine the material at the microscopic scale, with no thermal or mechanical adverse effects. The macro-characteristics of the cut surface, such as its taper, trailback, and waviness, are discussed, along with methods of improving the geometrical accuracy of the cut parts using these attributes. For example, dynamic angular compensation is used to correct for the taper and undercut in shape cutting. The surface finish is controlled by the cutting speed, hydraulic, and abrasive parameters using software and process models built into the controllers of CNC machines. In addition to shape cutting, edge trimming is presented, with a focus on the carbon fiber composites used in aircraft and automotive structures, where special AWJ tools and manipulators are used. Examples of the precision cutting of microelectronic and solar cell parts are discussed to describe the special techniques that are used, such as machine vision and vacuum-assist, which have been found to be essential to the integrity and accuracy of cut parts. The use of the AWJ machining process was extended to other applications, such as drilling, boring, milling, turning, and surface modification, which are presented in this paper as actual industrial applications. To demonstrate the versatility of the AWJ machining process, the data in this paper were selected to cover a wide range of materials, such as metal, glass, composites, and ceramics, and also a wide range of thicknesses, from 1 mm to 600 mm. The trends of Industry 4.0 and 5.0, AI, and IoT are also presented.

36 MATERIALS SCIENCE↗
NASA NTRS1965

Manufacturing research in support of Saturn V

Manufacturing techniques for production of Saturn V components - high pressure liquid and pneumatic ducting systems, age forming, welding, tooling, chemical milling, and composites

SATURN V LAUNCH VEHICLE↗
NASA NTRS2002

On the measurement of stationary electric fields in air

Applications and measurement methods for field measurements are reviewed. Recent developments using optical technology are examined. The various methods are compared. It is concluded that the best general purpose instrument is the isolated cylindrical field mill, but MEMS technology could furnish better instruments in the future.

electric fields measurement field mill↗
NASA NTRS1995

(abstract) All Epitaxial Edge-geometry SNS Devices with Doped PBCO and YBCO Normal Layers

We will present our results on tapered-edge-geometry SNS weak link fabricated from c-axis oriented base-, counterelectrode and normal layers using a variety of processing conditions. To date, we have employed a variety of different normal materials (Co-doped YBCO, Y-doped PBCO, Ca-doped PBCO). We have been examining the junction fabrication process in detail and we will present our methods. In particular, we have been examining both epitaxial and non-epitaxial milling mask overlayers and we will present a comparison of both methods. These devices behave similar to the expectations of the resisively shunted junction model and conventional SNS proximity effect models but with some differences which will be discussed. We will present the detailed systematics of our junctions including device parameters versus temperature, rf and dc magnetic response for the various processing conditions.

epitaxial doped PBCO YBCO junction fabrication mil↗
DOE OSTI2021

FCIC DFO--Moisture Management and Optimization in Municipal Solid Waste Feedstock through Mechanical Processing

The project goal is to produce densified product, focusing on characteristics of bulk density, durability, and moisture content, to reduce the cost of preprocessing. The objective of the project is to efficiently manage and handle the properties of MSW feedstock through INL-developed fractional milling, high moisture pelleting, and low temperature drying preprocessing technologies .

09 BIOMASS FUELS↗
DOE OSTI2023

Particle Scale Impacts on Deconstruction Energy of Pine Residues

The goal of this Case Study was to quantify the impacts of variable moisture and ash on hammer mill throughput and energy consumption and on generation of fines that are not able to be fed to conversion, as compared to a status quo Base Case system. Also considered was convertible carbon content (minimum carbon specification) and maximum ash content and the delivered feedstock cost impacts of not being able to feed residue not meeting both specifications to the conversion reactor. Laboratory data on the impacts of input particle size and moisture content on the exit particle size were received from FCIC Subtask 5.2: Preprocessing, High Temperature Conversion Preprocessing from their single particle impact population balance modeling study (Tiasha Bhattacharjee, INL). Additional throughput and energy consumption data were obtained from FCIC Subtask 5.2 (Jordan Klinger, INL) for the same grinder with a 6 mm screen in place. These data were utilized to develop the necessary response surface equations to perform throughput analysis using discrete event simulation. Because the ash contents in the separated fines had not been analyzed in the laboratory at the time of the model runs, we chose to assume that the ash distributed proportionally with total mass into the overs and unders in the disk screen following grinding.

energy consumption↗
DOE OSTI2020

Development of an In-Situ Leaching Technology for Extracting Residual Uranium from Remediated Soil - 20099

Site-specific chemical solutions for extracting uranium were developed and evaluated for treating previously remediated soil at a former thorium mill tailings site, known as the Former Rare Earths Facility (REF), in West Chicago, Illinois. Prior remediation efforts had resulted in residual sand and gravel aggregate that met the soil cleanup standards. The target soil contains residual levels of uranium, which continues to leach into the site groundwater at levels exceeding groundwater protection standards (GWPS). A series of bench-scale tests were conducted to evaluate the efficacy and viability of in-situ leaching (ISL) technology to treat the target soil for the purposes of attaining uranium GWPS at the REF. Specific objectives of the bench-scale tests entailed identification and selection of optimal leaching, quantification of the extent and rate of uranium released as a function of chemical composition, chemical concentrations, chemical residence times, and obtaining critical data to estimate treatment costs. A combination of sodium bicarbonate and sodium carbonate reagent was the most effective leaching solution. In general, leaching solutions containing a higher concentration of sodium carbonate demonstrated superior uranium leaching capabilities. Removal of 50% of the uranium mass from the soil matrix was adequate for achieving compliance with the site-specific GWPS. After six to seven pore volume flushes (PVFs), the uranium leaching effectiveness of all leaching solutions was similar. The amount of initial uranium removed with each subsequent PVF was minimal, suggesting limited solubility of the remaining mass of uranium. The effects of leaching duration were significant and persisted through at least the first five consecutive PVFs. Leaching of uranium also resulted in leaching of several non-uranium constituents, many of which exceeded applicable National Pollutant Discharge Elimination System (NPDES) standards. Given historical operations and waste disposal practices at the site, leaching of non-uranium constituents was expected. Hydrochloric acid was used to stabilize treated soil. Savings of approximately $148 million in direct and indirect remediation costs are expected with an ISL alternative compared to the excavation and landfill disposal remediation option. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

In Situ Cyclized Polyacrylonitrile Coating: Key to Stabilizing Porous High-Entropy Oxide Anodes for High-Performance Lithium-Ion Batteries

High-entropy oxides (HEOs) composed of multiple metal elements have attracted great attention as anode materials for lithium-ion batteries (LIBs) due to the synergistic effects of various metal species. However, the practical applications of HEOs are still plagued by poor conductivity, unstable solid electrolyte interphase (SEI) and poor cycling stability. In this work, nanosized (FeCoNiCrMn) 3 O 4 HEO (NHEO) is prepared successfully by the NaCl-assisted mechanical ball-milling strategy. Novelly, polyacrylonitrile (PAN) is used as the binder and then in situ thermochemically cyclized to construct a cyclized PAN (cPAN) outer layer onto NHEO (NHEO-cPAN). The in situ formed cPAN coating not only improves the electrical conductivity, but also reinforces the structural and interfacial stability, and thereby, the resulted NHEO-cPAN electrode exhibits significantly enhanced rate and cyclic performance. Specifically, NHEO-PAN500 electrode delivers a high reversible capacity of 560 mAh g –1 at 5 A g –1 and a high-capacity retention of 83% over 800 cycles at 3 A g –1 . Furthermore, the structural evolution and electrochemical behavior of NHEO-PAN electrode during discharge/charge is systematically investigated by operando X-ray diffraction, in situ impedance spectroscopy and ex situ high-resolution transmission electron microscopy. Therefore, this work provides new insights into the engineering of electrode and interphase for high-performance HEO electrode materials, potentially enlightening the practical applications of HEO-based LIBs.

25 ENERGY STORAGE↗
DOE OSTI2021

New Insights into the High‐Performance Black Phosphorus Anode for Lithium‐Ion Batteries

Abstract Black phosphorus (BP) is a promising anode material in lithium‐ion batteries (LIBs) owing to its high electrical conductivity and capacity. However, the huge volume change of BP during cycling induces rapid capacity fading. In addition, the unclear electrochemical mechanism of BP hinders the development of rational designs and preparation of high‐performance BP‐based anodes. Here, a high‐performance nanostructured BP–graphite–carbon nanotubes composite (BP/G/CNTs) synthesized using ball‐milling method is reported. The BP/G/CNTs anode delivers a high initial capacity of 1375 mA h g −1 at 0.15 A g −1 and maintains 1031.7 mA h g −1 after 450 cycles. Excellent high‐rate performance is demonstrated with a capacity of 508.1 mA h g −1 after 3000 cycles at 2 A g −1 . Moreover, for the first time, direct evidence is provided experimentally to present the electrochemical mechanism of BP anodes with three‐step lithiation and delithiation using ex situ X‐ray diffraction (XRD), ex situ X‐ray absorption spectroscopy (XAS), ex situ X‐ray emission spectroscopy, operando XRD, and operando XAS, which reveal the formation of Li 3 P 7 , LiP, and Li 3 P. Furthermore, the study indicates an open‐circuit relaxation effect of the electrode with ex situ and operando XAS analyses.

Li, Minsi↗
DOE OSTI2026

New Directions in Focused Ion Beam Induced Deposition for the Nanoprinting of Functional 3D Heterostructures

The focused ion beam (FIB) microscope is well established as a high-resolution machining instrument capable of site-selectively removing material down to the nanoscale. Beyond subtractive processing, however, the FIB can also add material via a technique known as focused ion beam induced deposition (FIBID). Using FIBID, the FIB can thus be employed for the direct-write of complex nanostructures. This work explores new directions in three-dimensional FIBID nanoprinting, harnessing unique features of helium and neon FIBs. In particular, the superior spatial resolution of these novel FIBs is leveraged to fabricate precise multimaterial architectures, an isotope effect is used to create satellite deposits, and dose-controlled implantation of the gaseous ions is used to engineer internal voids. In the context of voids, the fabrication of hollow nanopillars by helium-FIBID due to concurrent milling (as shown previously by others) is revisited. Insight into the chemical and structural composition of the nanostructures is obtained using advanced electron microscopy, accurately revealing buried interfaces, crystallite distributions, chemical compositions, and material transformations. Next-generation devices and technologies that could be enabled by the novel heterostructures demonstrated here are discussed, setting the stage for the potential evolution of FIBID into a versatile platform for functional nanomaterials design and fabrication.

FIBID↗