Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material design and testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Thermal Testing of the Heatshield for Extreme Entry Environment Technology (HEEET) TPS

The testing of a thermal protection system (TPS) in multiple arc jets and laser facilities is critical not only to determine the ability of a material to withstand the harsh aerothermal environments but is also required to collect relevant data that allows construction of a thermal response model of the TPS for flight design. The present talk provides an overview of recent arcjet testing of the HEEET material, one of the families of materials from the 3D Woven TPS program, being developed under NASAs Heatshield for Extreme Entry Environment Technology (HEEET) project.

Gasch, M,↗
NASA NTRS1979

Development of procedures for calculating stiffness and damping of elastomers in engineering applications. Part 5: Elastomer performance limits and the design and test of an elastomer damper

Tests were performed on elastomer specimens of the material polybutadiene to determine the performance limitations imposed by strain, temperature, and frequency. Three specimens were tested: a shear specimen, a compression specimen, and a second compression specimen in which thermocouples were embedded in the elastomer buttons. Stiffness and damping were determined from all tests, and internal temperatures were recorded for the instrumented compression specimen. Measured results are presented together with comparisons between predictions of a thermo-viscoelastic analysis and the measured results. Dampers of polybutadiene and Viton were designed, built, and tested. Vibration measurements were made and sensitivity of vibration to change in unbalance was also determined. Values for log decrement were extracted from the synchronous response curves. Comparisons were made between measured sensitivity to unbalance and log decrement and predicted values for these quantities.

Tecza, J. A.↗
DOE OSTI2024

The Digital Engineering Vision for DOME: Facilitating Design, Deployment, and Operations [Poster]

DOME is a planned microreactor test facility at INL’s Materials and Fuels Complex. It is a complex system with several interdependent sub-systems such as the reactor (up to 20 MWth), radioactive confinement, temperature and pressure regulation system, ventilation system, etc. The engineering design process for such a system traditionally involves several documents from various sources and the system information is scattered across these documents. Digital engineering represents a paradigm shift through which systems are designed using digital models and integrated data. The digital engineering vision for DOME utilizes a model-based systems engineering (MBSE) approach. The system architecture, physical components, control logic, and verification experiments are all designed using MathWorks MATLAB and Simulink. This hierarchical model can combine data from multiple sources at various levels of abstraction. It can be used to simulate the facility’s operations and to test the system using different sets of parameters. Its capabilities can be expanded by interfacing it with high-fidelity multi-physics models, risk analysis tools, etc. The same model can evolve into a digital twin that can monitor operations and conduct predictive analysis using real-time sensor data from the facility. The eventual goal of this effort is to transform the end-to-end engineering of nuclear facilities in every phase of their lifecycle, including design, deployment, and operations.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1978

Modified Composite Materials Workshop

The reduction or elimination of the hazard which results from accidental release of graphite fibers from composite materials was studied at a workshop. At the workshop, groups were organized to consider six topics: epoxy modifications, epoxy replacement, fiber modifications, fiber coatings and new fibers, hybrids, and fiber release testing. Because of the time required to develop a new material and acquire a design data base, most of the workers concluded that a modified composite material would require about four to five years of development and testing before it could be applied to aircraft structures. The hybrid working group considered that some hybrid composites which reduce the risk of accidental fiber release might be put into service over the near term. The fiber release testing working group recommended a coordinated effort to define a suitable laboratory test.

Dicus, D. L.↗
NASA NTRS1988

Roller drive materials performance

Roller traction performance basics, a test program to measure performance, and the need for and typical use of the information are outlined. A test rig was designed and fabricated to develop this information. Parametric conditions and specimen materials were chosen so that the resulting data will be valuable to the design and development of advanced, roller-driven space mechanisms, from precision positioning devices to telerobot joints.

Rohn, Douglas A.↗
NASA NTRS2026

Polymer Composite Material Testing for a Cryotank Application

Composite cryotanks will play a key role in enabling the next generation of efficient aircraft. Carbon fiber reinforced polymer (CFRP) composites have the benefits of reduced weight and potentially higher structural strength compared to traditional metallic fuel tanks. A material screening study was conducted to inform material selection for liquid hydrogen (LH2) fuel storage. Three composite materials were considered because of their aerospace grade toughness, strength, and existing data to compare against. These materials were a thermoplastic low-melt polyaryletherketone (LM-PAEK)/carbon fiber (CF), thermoset/CF, and hybrid thermoset/thermoplastic polyurethane (TPU) veil/CF composite. Mechanical screening tests included tension, compression, in-plane shear (IPS), and tensile-tensile fatigue (TTF). Each material was tested at both a baseline (no liquid nitrogen/LN2 cycling) and 100 LN2-cycled conditions to determine the knockdown factor, if any, of each material when exposed to environmental loading effects in a cryotank. Results show minimal effects of the LN2-cycling compared against baseline values. The three materials behaved similarly in tension; however, the thermoplastic/CF had the highest IPS toughness. The hybrid thermoset/TPU/CF composite had the lowest IPS strength, compressive strength, and toughness. LN2-cycling had minimal effects on tensile-tensile fatigue performance of the thermoplastic/CF material. Mechanical data was captured to guide material down selection for future commercially viable hydrogen aircraft design. In its current state, there does not exist a consolidated, publicly available database for CFRP composite material performance data at cryogenic temperatures. The next step in this work is to test the thermoplastic and thermoset CFRP composites, as well as the neat resins, at LH2 relevant temperature (20 K) to capture this crucial material property data. These results are essential to inform cryotank design and modeling efforts. The process to start this next round of testing has begun. Planned mechanical tests include toughness (single-edge notched beam), tension (unidirectional and quasi-isotropic), thermal expansion, and thermal conductivity. Some tests will also be conducted at an intermediate temperature of 111 K relevant to liquid natural gas (LNG), another attractive fuel choice. The ultimate goal is to manufacture a sub-scale cryotank part that can pass relevant burst, fatigue, permeation, and thermal cycling tests. This work is a part of NASA’s Commercially viable Hydrogen Aircraft for Robust Growth in Efficiency (CHARGE) Project under the larger NASA Subsonic Vehicle Technologies and Tools (SVTT) Project.

composites↗
NASA NTRS1999

Advanced High Temperature Polymer Matrix Composites for Gas Turbine Engines Program Expansion

This document, submitted by AlliedSignal Engines (AE), a division of AlliedSignal Aerospace Company, presents the program final report for the Advanced High Temperature Polymer Matrix Composites for Gas Turbine Engines Program Expansion in compliance with data requirements in the statement of work, Contract No. NAS3-97003. This document includes: 1 -Technical Summary: a) Component Design, b) Manufacturing Process Selection, c) Vendor Selection, and d) Testing Validation: 2-Program Conclusion and Perspective. Also, see the Appendix at the back of this report. This report covers the program accomplishments from December 1, 1996, to August 24, 1998. The Advanced High Temperature PMC's for Gas Turbine Engines Program Expansion was a one year long, five task technical effort aimed at designing, fabricating and testing a turbine engine component using NASA's high temperature resin system AMB-21. The fiber material chosen was graphite T650-35, 3K, 8HS with UC-309 sizing. The first four tasks included component design and manufacturing, process selection, vendor selection, component fabrication and validation testing. The final task involved monthly financial and technical reports.

Hanley, David↗
NASA NTRS1975

Performance of solar shields

The loss of the micrometeoroid shield from the Orbital Workshop section of Skylab I, about 63 seconds after lift-off, proved to be the harbinger of a prodigious effort to quickly develop a workable substitute for the carefully tailored passive portion of the thermal-control system. The paper describes the intensive ten-day around-the-clock effort in which numerous potential thermal-shield materials were assessed, and during which period ten specific shield designs were developed and carried through various stages of development and test. Thermal-shield materials data are discussed, including optical, strength, fatigue, outgassing, tackiness, ultraviolet radiation, and material 'memory' properties.

Schwinghamer, R. J.↗
NASA NTRS1985

Design and construction of models for the National Transonic Facility, part 1

The design and construction of models for the National Transonic Facility (NTF) has resulted in significant technology developments in many areas. This lecture covers the development of design criteria and major research and development work that has contributed to the successful design and fabrication models for testing at full scale Reynolds number the NTF. Emphasis is placed on the materials aspect of the design and fabrication proces, including metallic materials, mechanical properties characterization, new steel alloy development, fracture toughness enhancement, and identification of fillers and solders suitable for use in cryogenic models. Quantitative data are provided which will be of value to the potential user of NTF or for application to the design and fabrication of model systems for other cryogenic wind tunnels.

Young, C. P., Jr.↗
NASA NTRS2001

Safer Aviation Materials Tested

A series of thermally stable polymer samples were tested. These materials are called low heat release materials and are designed for aircraft interior decorative materials. The materials are designed to give off a minimum amount of noxious gases when heated, which increases the possibility that people can escape from a burning aircraft. New cabin materials have suitably low heat release so that fire does not spread, toxic chemicals are not given off, and the fire-emergency escape time for crew and passengers is lengthened. These low heat-release materials have a variety of advantages and applications: interiors for ground-based facilities, interiors of space vehicles, and many commercial fire-protection environments. A microscale combustion calorimeter at the Federal Aviation Administration's (FAA) Technical Center tested NASA Langley Research Center materials samples. The calorimeter is shown. A sharp, quantitative, and reproducible heat-release-rate peak is obtained in the microscale heat-release-rate test. The newly tested NASA materials significantly reduced the heat release capacity and total heat release. The thermal stability and flammability behavior of the samples was very good. The new materials demonstrated a factor of 4 reduction in total heat release over ULTEM (a currently used material). This information is provided in the following barchart. In other tests, the materials showed greater than a factor 9 reduction in heat-release capacity over ULTEM. The newly tested materials were developed for low dielectric constant, low color, and good solubility. A scale up of the material samples is needed to determine the repeatability of the performance in larger samples. Larger panels composed of the best candidate materials will be tested in a larger scale FAA Technical Center fire facility. The NASA Glenn Research Center, Langley (Jeff Hinkley), and the FAA Technical Center (Richard Lyon) cooperatively tested these materials for the Accident Mitigation aspects of Fire Prevention under NASA's Aviation Safety Program.

Palaszewski, Bryan A.↗
NASA NTRS1976

Advanced Composites: Mechanical Properties and Hardware Programs for Selected Resin Matrix Materials

This design note presents typical mechanical properties tabulated from industrial and governmental agencies' test programs. All data are correlated to specific products and all of the best known products are presented. The data include six epoxies, eight polyimides and one polyquinoxaline matrix material. Bron and graphite are the fiber reinforcements. Included are forty-two summaries of advanced (resin matrix) composite programs in existence in the United States. It is concluded that the selection of appropriate matrices, the geometric manner in which the fibers are incorporated in the matrix and the durability of the bond between fiber and matrix establish the end properties of the composite material and the performance of the fabricated structure.

Welhart, E. K.↗
NASA NTRS1974

Design, fabrication, and test of lightweight shell structure

A cylindrical shell skirt structure was subjected to a design and analysis study using a wide variety of structural materials and concepts. The design loading, axial compression, and torsion is representative of that expected on a typical space tug skirt section. Structural concepts evaluated included honeycomb sandwich, truss, isogrid, and skin/stringer/frame. The materials considered included a wide variety of structural metals as well as glass, graphite, and boron-reinforced composites. Honeycomb sandwich with aluminum faceskins, honeycomb sandwich with graphite/epoxy faceskins, and aluminum truss with fiberglass meteoroid protection layers were the designs selected for further evaluation. Procurement of materials required for fabrication is reported and the structural test plan and fabrication drawings are included. Construction of the graphite/epoxy faceskins, chem mill of the aluminum faceskins, chem mill of aluminum truss components, and fabrication of the graphite/epoxy honeycomb sandwich development panel is also reported.

Source record↗
NASA NTRS2004

Goals and Progress for Mil Handbook 17, Vol. 5 on Ceramic Matrix Composites: Testing and Characterization

The initial edition of the Mil Handbook 17, Vol. 5 on ceramic matrix composites (CMCs) was recently published. Part C of this CMC volume describes procedures for characterization of the thermal, physical, and mechanical properties of CMCs and subsequent data analysis procedures. As is the case for entire CMC volume, this chapter is a "work in progress" with sections on recommended test plans and matrices, data reduction, and test methods. This presentation will describe the current status in development of this section of the CMC volume and will highlight examples of critical issues that will be addressed in this volume. CMC systems are a different class of material than metals or polymer matrix composite with different mechanical response and failure modes, design rules, test methods, and characterization techniques. The CMC test protocols need to include guidance on how to generate enough reliable data in order to estimate, with reasonable confidence, the lower bounds of performance properties, such as strength and life. Strength data sets on two material systems, C/SiC and Nicalon/SiNC, and a creep rupture data set on C/SiC, will be presented to highlight this issue. The structural properties of CMC parts can sometimes be significantly different than those obtained from flat panels because of changes in fiber architecture often required to make shapes and spatial and lot-to-lot variations in processing conditions. To illustrate an example, the hoop tensile properties of SiC/SiC cylinders will be compared to properties obtained from flat panels fabricated from the same composites. These CMC testing-design issues are being defined and documented in the Mil Handbook 17 CMC volume.

Verrilli, Michael J.↗
NASA NTRS1986

Experimental evaluation of candidate carbon-carbon materials for OTV engine nozzle extensions

Advanced carbon-carbon nozzle materials can reduce the weight and improve the efficiency of the proposed reusable Orbit Transfer Vehicle (OTV) liquid rocket engine. Experimental evaluations of eight carbon-carbon materials in an O2/H2 rocket nozzle environment have been performed. The hot fire testing will support the choice of the materials for the OTV nozzle design. The OTV nozzle requirements and operating environment are defined. The rocket device used to simulate the OTV hot-fire nozzle environment for material specimen evaluation is described. The results of hot-fire testing for eight carbon-carbon materials are discussed. Results for coated and uncoated materials, evaluated in side-by-side testing, are compared. Plans for further testing of the leading materials are described.

Suhoza, J. P.↗
DOE OSTI2023

A cryogenically cooled 200 kV DC photoemission electron gun for ultralow emittance photocathodes

Novel photocathode materials like ordered surfaces of single crystal metals, epitaxially grown high quantum efficiency thin films, and topologically non-trivial materials with dirac cones show great promise for generating brighter electron beams for various accelerator and ultrafast electron scattering applications. Despite several materials being identified as brighter photocathodes, none of them have been tested in electron guns to extract electron beams due to technical and logistical challenges. In this paper, we present the design and commissioning of a cryocooled 200 kV DC electron gun that is capable of testing a wide variety of novel photocathode materials over a broad range of temperatures from 298 to 35 K for bright electron beam generation. This gun is designed to enable easy transfer of the photocathode to various standard ultra-high-vacuum surface diagnostics and preparation techniques, allowing a full characterization of the dependence of beam brightness on the photocathode material and surface properties. We demonstrate the development of such a high-voltage, high-gradient gun using materials and equipment that are easily available in any standard university lab, making the development of such 200 kV electron guns more accessible.

Instruments & Instrumentation↗
NASA NTRS2004

Suggested Procedures for Installing Strain Gauges on Langley Research Center Wind Tunnel Balances, Custom Force Measuring Transducers, Metallic and Composite Structural Test Articles

The character of force and strain measurement testing at LaRC is such that the types of strain gauge installations, the materials upon which the strain gauges are applied, and the test environments encountered, require many varied approaches. In 1997, a NASA Technical Memorandum (NASA TM 110327) was generated to provide the strain gauge application specialist with a listing of recommended procedures for strain gauging various transducers and test articles at LaRC. The technical memorandum offered here is an effort to keep the strain gauge user informed of new technological enhancements in strain-gauging methodology while preserving the strain-gauging guidelines set forth in the 1997 TM. This document provides detailed recommendations for strain gauging LaRC-designed balances and custom transducers, composite materials, cryogenic and high-temperature test articles, and selected non-typical or unique materials or test conditions. Additionally, one section offers details for installing Bragg-Grating type fiber-optic strain sensors for non-typical test scenarios.

Moore, Thomas C., Sr.↗
NASA NTRS2001

Thermal Design, Analysis, and Testing of the Quench Module Insert Bread Board

The science requirements for materials processing is to provide the desired PI requirements of thermal gradient, solid/liquid interface front velocity for a given processing temperature desired by the PI. Processing is performed by translating the furnace with the sample in a stationary position to minimize any disturbances to the solid/liquid interface front during steady state processing. Typical sample materials for this metals and alloys furnace are lead-tin alloys, lead-antimony alloys, and aluminum alloys. Samples must be safe to process and therefore typically are contained with hermetically sealed cartridge tubes (gas tight) with inner ceramic liners (liquid tight) to prevent contamination and/or reaction of the sample material with the cartridge tube.

Breeding Shawn↗
DOE OSTI2022

Machine Intelligence-Centered System for Automated Characterization of Functional Materials and Interfaces

Classic design of experiment relies on a time-intensive workflow that requires planning, data interpretation, and hypothesis building by experienced researchers. Here, in this paper, we describe an integrated, machine-intelligent experimental system which enables simultaneous dynamic tests of electrical, optical, gravimetric, and viscoelastic properties of materials under a programmable dynamic environment. Specially designed software controls the experiment and performs on-the-fly extensive data analysis and dynamic modeling, real-time iterative feedback for dynamic control of experimental conditions, and rapid visualization of experimental results. The system operates with minimal human intervention and enables time-efficient characterization of complex dynamic multifunctional environmental responses of materials with simultaneous data processing and analytics. The system provides a viable platform for artificial intelligence (AI)-centered material characterization, which, when coupled with an AI-controlled synthesis system, could lead to accelerated discovery of multifunctional materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗