Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Mask”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Evaluation of the cosmic-ray induced background in coded aperture high energy gamma-ray telescopes

While the application of coded-aperture techniques to high-energy gamma-ray astronomy offers potential arc-second angular resolution, concerns were raised about the level of secondary radiation produced in a thick high-z mask. A series of Monte-Carlo calculations are conducted to evaluate and quantify the cosmic-ray induced neutral particle background produced in a coded-aperture mask. It is shown that this component may be neglected, being at least a factor of 50 lower in intensity than the cosmic diffuse gamma-rays.

Owens, Alan↗
NASA NTRS1992

Technologies for automating rotorcraft nap-of-the-earth flight

This paper discusses the technologies required for automating rotorcraft nap-of-the-earth flight, where the use of natural obstacles for masking from the enemy is intentional and the danger of undesirable obstacles such as enemy traps is real. Specifically, the automatic guidance structure is modeled by three decision-making levels: the far-field mission planning and the mid-field terrain-masking trajectory shaping are both driven by prestored terrain data, whereas the nearfield obstacle detection/avoidance is driven by real-time on-board sensor data. This paper summarizes the far-field and mid-field accomplishments, and reports on the status of the more-recent efforts in obstacle detection and avoidance development. Obstacle detection is based primarily on passive imaging sensors for the desirable properties of covertness and wide field of view, although active sensors are included in the structure to provide the much needed high resolution for thin-wire detection.

Cheng, Victor H. L.↗
NASA NTRS1992

A comparison of three SAR interference filters

Three interference filters are discussed and their ability to remove the interference while leaving target signal data is quantified. The filters are adaptive frequency-domain spike filtering; adaptive frequency-domain interference determination and masking; and interference-target correlation masking. Using Jet Propulsion Laboratory Airborne Synthetic Aperture Radar (JPL AIRSAR) data, the algorithms are applied to three data sets. The resultant compressed Stokes matrix data are compared with the normally processed interference-free image in a quantitative sense. The algorithms are evaluated by measuring the polarization signature, SNR, equivalent number of looks, and impulse response of the processed images.

Chapman, B.↗
NASA NTRS1977

Voice integrated systems

The program at Naval Air Development Center was initiated to determine the desirability of interactive voice systems for use in airborne weapon systems crew stations. A voice recognition and synthesis system (VRAS) was developed and incorporated into a human centrifuge. The speech recognition aspect of VRAS was developed using a voice command system (VCS) developed by Scope Electronics. The speech synthesis capability was supplied by a Votrax, VS-5, speech synthesis unit built by Vocal Interface. The effects of simulated flight on automatic speech recognition were determined by repeated trials in the VRAS-equipped centrifuge. The relationship of vibration, G, O2 mask, mission duration, and cockpit temperature and voice quality was determined. The results showed that: (1) voice quality degrades after 0.5 hours with an O2 mask; (2) voice quality degrades under high vibration; and (3) voice quality degrades under high levels of G. The voice quality studies are summarized. These results were obtained with a baseline of 80 percent recognition accuracy with VCS.

Curran, P. Mike↗
NASA NTRS1993

A cost-effective methodology for the design of massively-parallel VLSI functional units

In this paper we propose a generalized methodology for the design of cost-effective massively-parallel VLSI Functional Units. This methodology is based on a technique of generating and reducing a massive bit-array on the mask-programmable PAcube VLSI array. This methodology unifies (maintains identical data flow and control) the execution of complex arithmetic functions on PAcube arrays. It is highly regular, expandable and uniform with respect to problem-size and wordlength, thereby reducing the communication complexity. The memory-functional unit interface is regular and expandable. Using this technique functional units of dedicated processors can be mask-programmed on the naked PAcube arrays, reducing the turn-around time. The production cost of such dedicated processors can be drastically reduced since the naked PAcube arrays can be mass-produced. Analysis of the the performance of functional units designed by our method yields promising results.

Venkateswaran, N.↗
NASA NTRS1993

DCT quantization matrices visually optimized for individual images

This presentation describes how a vision model incorporating contrast sensitivity, contrast masking, and light adaptation is used to design visually optimal quantization matrices for Discrete Cosine Transform image compression. The Discrete Cosine Transform (DCT) underlies several image compression standards (JPEG, MPEG, H.261). The DCT is applied to 8x8 pixel blocks, and the resulting coefficients are quantized by division and rounding. The 8x8 'quantization matrix' of divisors determines the visual quality of the reconstructed image; the design of this matrix is left to the user. Since each DCT coefficient corresponds to a particular spatial frequency in a particular image region, each quantization error consists of a local increment or decrement in a particular frequency. After adjustments for contrast sensitivity, local light adaptation, and local contrast masking, this coefficient error can be converted to a just-noticeable-difference (jnd). The jnd's for different frequencies and image blocks can be pooled to yield a global perceptual error metric. With this metric, we can compute for each image the quantization matrix that minimizes the bit-rate for a given perceptual error, or perceptual error for a given bit-rate. Implementation of this system demonstrates its advantages over existing techniques. A unique feature of this scheme is that the quantization matrix is optimized for each individual image. This is compatible with the JPEG standard, which requires transmission of the quantization matrix.

Watson, Andrew B.↗
NASA NTRS1995

Etching Semiconductors With Beams Of Reactive Atoms

Method of etching semiconductors with energetic beams of electrically neutral, but chemically reactive, species undergoing development. Enables etching of straight walls into semiconductor substrates at edges of masks without damage to underlying semiconductor material. In addition to elimination of charge damage, technique reduces substrate bombardment damage because translational energy of neutral species in range 2-12 eV, below damage threshold of many semiconductor materials. Furthermore, low-energy neutrals cause no mask erosion allowing for etching features with very high aspect ratios.

Minton, Timothy K.↗
NASA NTRS1991

A Scheduling Algorithm for Replicated Real-Time Tasks

We present an algorithm for scheduling real-time periodic tasks on a multiprocessor system under fault-tolerant requirement. Our approach incorporates both the redundancy and masking technique and the imprecise computation model. Since the tasks in hard real-time systems have stringent timing constraints, the redundancy and masking technique are more appropriate than the rollback techniques which usually require extra time for error recovery. The imprecise computation model provides flexible functionality by trading off the quality of the result produced by a task with the amount of processing time required to produce it. It therefore permits the performance of a real-time system to degrade gracefully. We evaluate the algorithm by stochastic analysis and Monte Carlo simulations. The results show that the algorithm is resilient under hardware failures.

Yu, Albert C.↗
NASA NTRS1997

Optical Verification Laboratory Demonstration System for High Security Identification Cards

Document fraud including unauthorized duplication of identification cards and credit cards is a serious problem facing the government, banks, businesses, and consumers. In addition, counterfeit products such as computer chips, and compact discs, are arriving on our shores in great numbers. With the rapid advances in computers, CCD technology, image processing hardware and software, printers, scanners, and copiers, it is becoming increasingly easy to reproduce pictures, logos, symbols, paper currency, or patterns. These problems have stimulated an interest in research, development and publications in security technology. Some ID cards, credit cards and passports currently use holograms as a security measure to thwart copying. The holograms are inspected by the human eye. In theory, the hologram cannot be reproduced by an unauthorized person using commercially-available optical components; in practice, however, technology has advanced to the point where the holographic image can be acquired from a credit card-photographed or captured with by a CCD camera-and a new hologram synthesized using commercially-available optical components or hologram-producing equipment. Therefore, a pattern that can be read by a conventional light source and a CCD camera can be reproduced. An optical security and anti-copying device that provides significant security improvements over existing security technology was demonstrated. The system can be applied for security verification of credit cards, passports, and other IDs so that they cannot easily be reproduced. We have used a new scheme of complex phase/amplitude patterns that cannot be seen and cannot be copied by an intensity-sensitive detector such as a CCD camera. A random phase mask is bonded to a primary identification pattern which could also be phase encoded. The pattern could be a fingerprint, a picture of a face, or a signature. The proposed optical processing device is designed to identify both the random phase mask and the primary pattern [1-3]. We have demonstrated experimentally an optical processor for security verification of objects, products, and persons. This demonstration is very important to encourage industries to consider the proposed system for research and development.

Javidi, Bahram↗
NASA NTRS1999

Effects of Inboard Horizontal Field of View Display Limitations on Pilot Path Control During Total In-Flight Simulator (TIFS) Flight Test

A flight test was conducted aboard Calspan's Total In-Flight Simulator (TIFS) aircraft by researchers within the External Visibility System (XVS) element of the High-Speed Research program. The purpose was to investigate the effects of inboard horizontal field of view (FOV) display limitations on pilot path control and to learn about the TIFS capabilities and limitations for possible use in future XVS flight tests. The TIFS cockpit windows were masked to represent the front XVS display area and the High-Speed Civil Transport side windows, as viewed by the pilot. Masking limited the forward FOV to 40 deg. horizontal and 50 deg. vertical for the basic flight condition, With an increase of 10 deg. horizontal in the inboard direction for the increased FOV flight condition. Two right-hand approach tasks (base-downwind-final) with a left crosswind on final were performed by three pilots using visual flight rules at Niagara Falls Airport. Each of the two tasks had three replicates for both horizontal FOV conditions, resulting in twelve approaches per test subject. Limited objective data showed that an increase of inboard FOV had no effect (deficiences in objective data measurement capabilities were noted). However, subjective results showed that a 50 deg. FOV was preferred over the 40 deg. FOV.

Kramer, Lynda J.↗
NASA NTRS1992

Black Carbon (Soot) Aerosol in the Lower Stratosphere and Upper Troposphere

We have used two approaches to measure BCA in the stratosphere. The first method consists of collecting aerosols by impaction on quartz rods, upon which are mounted strips of polystyrene filter material. Each 25 mm by 0.5 mm filter strip is alternately masked and exposed in 5 mm long sections. After sampling, the optical density of the exposed sections is measured and compared with the optical density of the masked (unexposed) sections. The filter strip is a Lambertian collector, the scattering property of which is not affected by the deposition of liquid sulfuric acid droplets which dominate the stratospheric aerosol. Hence, all attenuation greater in the exposed than in the non-exposed sections is due to absorption by BCA or rare opaque materials such as meteoritic iron. In a second approach we expose carbon-coated gold or palladium wires to air outside the aircraft boundary layer [Farlow et al., 1979; Pueschel et al., 1989]. With a field emission scanning electron microscope we are able to characterize BCA particles in addition to the dominant sulfuric acid droplets. Typically, soot is comprised of 20 nm diameter spheres linked together as branching chains or loosely packed aggregates (Figure 1a). The microscope has a lateral image resolution of 1.5 nm and can clearly resolve individual spheres making up BCA aggregates. Their morphology is uniquely different from that of the liquid sulfuric acid-water aerosol (Figure 1b). We approximate the size of each BCA particle by that of a sphere of equivalent volume and fit a lognormal size distribution to both the BCA and H2SO4/H2O aerosols. Both sampler types have been mounted on NASA's ER-2 high-altitude research aircraft (altitude ceiling of 70,000 feet), and on NASA's DC-8 (40,000 feet ceiling) aircraft to sample aerosols from a significant portion of the atmosphere.

Pueschel, R. F.↗
NASA NTRS2000

Early Results from the MODIS Atmosphere Cloud Algorithms

The Moderate Resolution Imaging Spectroradiometer (MODIS) is one of five instruments aboard the Terra Earth Observing System platform launched in December 1999. With 36 spectral bands from the visible through the infrared, and spatial resolution from 250m to 1km, the instrument provides an unprecedented opportunity for global cloud studies. A comprehensive set of remote sensing algorithms for cloud masking and retrieval of cloud physical and optical properties have been developed by members of the MODIS atmosphere team. The archived products from these algorithms have applications in climate change studies, climate modeling, numerical weather prediction, as well as fundamental atmospheric research. In addition to an extensive cloud mask, products include cloud top physical parameters (temperature, pressure, emissivity), cloud phase, cloud optical parameters (optical depth, effective particle radius, water path), visible cirrus reflectance, a contrail flag, and other derived parameters. All products are archived into two categories: pixel-level retrievals at a 1 km or 5 km spatial resolution at nadir (referred to as Level-2 products) and 1 degree global gridded statistics (Level-3 products). An overview of the MODIS atmosphere algorithms and products, their status, validation activities, and early level-2 and -3 results will be presented.

Platnick, S.↗
NASA NTRS2000

SeaWiFS Postlaunch Calibration and Validation Analyses

The effort to resolve data quality issues and improve on the initial data evaluation methodologies of the Sea-viewing Wide Field-of-view Sensor (SeaWiFS) Project was an extensive one. These evaluations have resulted, to date, in three major reprocessings of the entire data set where each reprocessing addressed the data quality issues that could be identified up to the time of each reprocessing. The number of chapters (21) needed to document this extensive work in the SeaWiFS Postlaunch Technical Report Series requires three volumes. The chapters in Volumes 9, 10, and 11 are in a logical order sequencing through sensor calibration, atmospheric correction, masks and flags, product evaluations, and bio-optical algorithms. The first chapter of Volume 9 is an overview of the calibration and validation program, including a table of activities from the inception of the SeaWiFS Project. Chapter 2 describes the fine adjustments of sensor detector knee radiances, i.e., radiance levels where three of the four detectors in each SeaWiFS band saturate. Chapters 3 and 4 describe the analyses of the lunar and solar calibration time series, respectively, which are used to track the temporal changes in radiometric sensitivity in each band. Chapter 5 outlines the procedure used to adjust band 7 relative to band 8 to derive reasonable aerosol radiances in band 7 as compared to those in band 8 in the vicinity of Lanai, Hawaii, the vicarious calibration site. Chapter 6 presents the procedure used to estimate the vicarious calibration gain adjustment factors for bands 1-6 using the waterleaving radiances from the Marine Optical Buoy (MOBY) offshore of Lanai. Chapter 7 provides the adjustments to the coccolithophore flag algorithm which were required for improved performance over the prelaunch version. Chapter 8 is an overview of the numerous modifications to the atmospheric correction algorithm that have been implemented. Chapter 9 describes the methodology used to remove artifacts of sun glint contamination for portions of the imagery outside the sun glint mask. Finally, Chapter 10 explains a modification to the ozone interpolation method to account for actual time differences between the SeaWiFS and Total Ozone Mapping Spectrometer (TOMS) orbits.

Hooker, Stanford B.↗
NASA NTRS2001

Operational Cloud Detection in GEOS Imagery

The bispectral spatial coherence approach for the detection and masking of clouds is revisited with modifications for operational applications to Geostationary Operational Environmental Satellite (GOES) Imager and Sounder data. The approach applies an edge detection algorithm to a "difference" image to identify the edges or contours of the clouds. The difference image is generated as the difference between the 3.9 and 11 micrometer channels of the GOES sensors. This difference image better highlights cloud edges than either image alone and draws upon the emissivity differences in the various channels. The cloud contours are "filled-in" by referencing the thermal gradients in the 11-micrometer channel or difference image associated with the cloud edge. This paper and associate poster will present a preliminary validation of the bispectral spatial coherence approach and will compare the cloud masks generated with this approach to the National Oceanic and Atmospheric Administration/National Environmental Satellite, Data, and Information Service (NOAA/NESDIS) operational cloud products.

Jedlovec, Gary J.↗
NASA NTRS2001

A Novel Catalyst Deposition Technique for the Growth of Carbon Nanotubes

This viewgraph presentation provides information on the development of a technique at NASA's Ames Research Center by which carbon nanotubes (NT) can be grown. The project had several goals which included: 1) scaleability, 2) ability to control single wall nanotube (SWNT) and multiwall nanotube (MWNT) formation, 3) ability to control the density of nanotubes as they grow, 4) ability to apply standard masking techniques for NT patterning. Information regarding the growth technique includes its use of a catalyst deposition process. SWNTs of varying thicknesses can be grown by changing the catalyst composition. Demonstrations are given of various methods of masking including the use of transmission electron microscopic (TEM) grids.

Delzeit, Lance↗
NASA NTRS1994

Spatial Attention Enhances Perceptual Processing of Single-Element Displays

Shiu and Pashler (1993) reported that precueing masked, single-element displays had negligible effects on identification accuracy. They argued that spatial attention does not actually enhance stimulus perceptibility, but only reduces decision noise. Alternatively, such negative results may arise if cues are sub-optimal, or if masks place an insufficient premium on timely deployment of attention. We report results showing that valid cueing enhances processing of even single-element displays. Spatial attention does indeed enhance perceptual processes.

Bacon, William↗
NASA NTRS1994

Enhancing Displays by Blurring

Some Enhanced Vision cockpit displays consist of synthetic imagery superimposed on a real image. The high spatial frequency components of the synthetic imagery can mislead an operator by masking features of the real image. We demonstrate that blurring the synthetic image prior to superposition reduces its masking effect in high- contrast regions of the real image, while maintaining its enhancing properties in regions of the real image where visibility is low.

Tiana, C.↗
NASA NTRS1995

Flight Schedule and the Circadian Clock Influence on Sleep Loss During Overnight Cargo Operations

Thirty-four flight crew members were monitored before, during, and after two 8-day overnight cargo duty patterns which involved multiple flights at night crossing no more than one time zone per 24 h. Rectal temperature, heart rate, and wrist activity were recorded every 2 min. Sleep quantity and quality, and nap timing, were noted in a logbook. To reduce the masking effects of physical activity on temperature, 0.28 C was added to each subject's raw temperature data whenever he reported being asleep. For both masked and unmasked data, daily temperature minima were estimated from the multiple complex demodulated waveform. The temperature minima did not show a progressive adaptation to night duty, which was interrupted by a night off after 5 nights on one trip pattern and after 3 nights on the other. On duty days, the average temperature minimum delayed by about 3 h, occurring near the end of the duty period. Daytime sleep episodes averaged 2.9 h shorter than nighttime sleep episodes, and were rated as lighter, less restorative, and poorer overall. Fifty-three percent of subjects slept more than once per 24 h while they were on night duty, compared to 17% when able to sleep at night. The total sleep per 24 h on duty days averaged 1.2 h less than pretrip. Twenty-nine percent of subjects lost more than 2 h of sleep per 24 h across the 8-day duty patterns. After night duty, subjects awoke around 1400 local time, even when they had slept 2-3 h less than a normal nocturnal sleep episode. Consequently, the duration of morning sleep episodes was correlated with the off-duty time (multiple r(sup 2)=0.44, F=37.23, p less than 0.0001). Anecdotally, crew members complained of being unable to sleep longer and not feeling well-rested. These wakeups were clustered 6 h after the temperature minimum, which suggests that they may have been a response to the circadian wakeup signal. Daytime layovers in which crew members were able to sleep again in the evening ended later (0200-0300) and were longer (average 19.2 h versus 14.8 h) than those in which they slept only once in the morning. Overnight cargo crew members are working around the time of the circadian nadir with an accumulating sleep debt. Two scheduling factors affect sleep loss during these operations: how long before the circadian wakeup signal crew members come off duty, and whether the layover lasts long enough to permit a second sleep episode in the early evening.

Gander, Philippa H.↗