Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Electrical resistivity change in Al:ZnO thin films dynamically deposited by bipolar pulsed direct-current sputtering and a remote plasma source

The Al-doped ZnO (AZO) thin films for a transparent conducting oxide in solar cell devices were deposited by bipolar pulsed dc magnetron sputtering. This work was performed in an in-line type system and investigated AZO films in a static deposition mode and dynamic one, which is more important in the practical fields. Because of this dynamic deposition process, the zigzagged columnar structure was observed. This resulted in the decreasing electrical property, optical properties, and surface roughness. As a deposition in the dynamic mode, the resistivity increased from 1.64x10{sup -3} to 2.50x10{sup -3} {Omega} cm, as compared to that in the static mode, and the transmittance also decreased from 83.9% to 78.3%. To recover the disadvantage, a remote plasma source (RPS) was supported between the substrate and target for reducing zigzagged formation during the deposition. The deposition rate decreased by using RPS, but the electrical and optical properties of films got better than only dynamic mode. The resistivity and transmittance in the dynamic mode using RPS were 2.1x10{sup -3} {Omega} cm and 85.5%, respectively. In this study, the authors found the possibility to advance the electrical and optical properties of AZO thin films in the industry mode.

36 MATERIALS SCIENCE↗

Surface studies and measurement of pumping characteristic of NEG coating (Ti-V-Zr)

NEGs (non evaporable getters) when coated as thin film on the inner wall of vacuum pipes or chamber play vital role in the evacuation of a sealed off system after heating it to activation temperature. It creates the uniformity of pressure between two long pipes where pumping is not possible at each and every part. Ternary coating of materials Ti, Zr and V has prepared on SS304L by DC-magnetron sputtering technique. These coatings was claimed to be very good in H{sub 2} adsorption which lead to achieve very low pressures of the order of 10{sup -12}-10{sup -13} mbar, low SEY(Secondary Electron Yield) and Low photo desorption yield compared to bare SS surface. We have shown the morphology of surfaces of these coatings which play the principal role in adsorption of (H{sub 2},CO,CO{sub 2}, H{sub 2}O etc.) have been extensively studied by SEM/EDX technique. SEM showed the micron size thick film. Film thickness of micron level is useful for NEG to work for no. of atmospheric exposed cycles. Reduction of superficial surface oxide after heating it to different temperatures was main concern and studied by X-ray Photoelectron spectroscopic technique. It has also reported the pumping characteristic of the NEG coating. (author)

43 PARTICLE ACCELERATORS↗

Analytic model of the energy distribution function for highly energetic electrons in magnetron plasmas

This paper analyzes a situation which is common for magnetized technical plasmas such as dc magnetron discharges and high power impulse magnetron sputtering (HiPIMS) systems, where secondary electrons enter the plasma after being accelerated in the cathode fall and encounter a nearly uniform bulk. An analytic calculation of the distribution function of hot electrons is presented; these are described as an initially monoenergetic beam that slows down by Coulomb collisions with a Maxwellian distribution of bulk (cold) electrons, and by inelastic collisions with neutrals. Although this analytical solution is based on a steady-state assumption, a comparison of the characteristic time-scales suggests that it may be applicable to a variety of practical time-dependent discharges, and it may be used to introduce kinetic effects into models based on the hypothesis of Maxwellian electrons. The results are verified for parameters appropriate to HiPIMS discharges, by means of time-dependent and fully kinetic numerical calculations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Achieving omnidirectional photonic band gap in sputter deposited TiO{sub 2}/SiO{sub 2} one dimensional photonic crystal

The multilayer structure of TiO{sub 2}/SiO{sub 2} (11 layers) as one dimensional photonic crystal (1D PC) has been designed and then fabricated by using asymmetric bipolar pulse DC magnetron sputtering technique for omnidirectional photonic band gap. The experimentally measured photonic band gap (PBG) in the visible region is well matched with the theoretically calculated band structure (ω vs. k) diagram. The experimentally measured omnidirectional reflection band of 44 nm over the incident angle range of 0°-70° is found almost matching within the theoretically calculated band.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of stacking sequence on crystallization in Al/a-Ge bilayer thin films

Two types of bilayer thin films with different deposition sequences, i.e., amorphous Ge under Al (a-Ge/Al) and the inverse (Al/a-Ge), were prepared by magnetron sputtering at room temperature. In-situ and ex-situ thermal annealing were compared to study the effect of the stacking sequence on crystallization of amorphous Ge. Although metal-induced crystallization occurred in both cases at low temperature, layer exchange was observed only in a-Ge/Al. In fact, compressive stress could usually be produced when Ge atoms diffused into Al grain boundaries and crystallized there. In the a-Ge/Al system, the stress could be released through diffusion of Al atoms onto the surface and formation of hillocks. Thus, grain boundary (GB) mediated crystallization was dominant in the whole process and layer exchange occurred. However, in the Al/a-Ge system, it was difficult for stress to be relaxed because the Ge sublayer and substrate restricted the diffusion of Al atoms. GB-mediated crystallization was, therefore, considerably suppressed and interface-mediated crystallization was preferred without layer exchange. This leads to distinct morphologies of dendrites in the two systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Phosphor doping enhanced c-axis alignment and exchange decoupling of sputtered Co-Pt perpendicular thin films

In the present work, Co-23.0 at. % Pt and Co-23.0 at. % Pt-3.67 at. % P thin films with their c-axis perpendicular to the substrate surface were fabricated on a glass substrate by DC magnetron sputtering. X-ray diffraction and transmission electron microscopic analyses demonstrate that the doping of P improves the c-axis alignment and forms P-rich non-magnetic phase at grain boundary areas, the latter resulting in inter-granular exchange decoupling between Co-Pt grains. The improved c-axis alignment and the inter-granular exchange decoupling give rise to the increase of the out of plane coercivity and the squareness of the Co-Pt-P films.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Structural and luminescence properties of heavily doped radio-frequency-sputtered ZnTe:Cu thin films

We report on the structural and luminescence properties of ZnTe:Cu films containing Cu concentrations up to 12 at. % and prepared using rf magnetron sputtering. The lattice parameters of the various crystalline phases prevailing at different Cu concentrations (cubic, hexagonal, and orthorhombic) are calculated and compared with literature results on films prepared using other techniques. Study of the steady state photoluminescence and excitation spectra revealed the presence of three donor impurities involved in the well-known band at ∼1.70 eV (peak L) attributed to self-activated transition. One of these donors is merging partially with the conduction band and the two others have mutually overlapping density of states with maxima at 0.29 eV and 0.45 eV below the conduction band edge. Another donor that is resonant with the conduction continuum is responsible for a higher energy emission band (peak H). The density of states of this donor has a maximum at 0.57 eV above the conduction band edge for a copper concentration of 8.2 at. %. The emission peak H undergoes a blue shift and its intensity increases sharply relative to the intensity of the L peak with the increase of Cu concentration. Moreover, the H emission extends to photon energies higher than the band gap. A possible interpretation of the behaviour of the peak H in terms of recombination involving the resonant states is suggested.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The corrosivity and passivity of sputtered Mg-Ti alloys

Our study explored the possibility of forming a “stainless” Mg–Ti alloy. The electrochemical behavior of magnetron-sputtered Mg–Ti alloys was measured in a NaCl solution, and the surface films on the alloys were examined by XPS, SEM and TEM. Increased corrosion resistance was observed with increased Ti content in the sputtered Mg–Ti alloys, but passive-like behavior was not reached until the Ti level (atomic %) was higher than the Mg level. Moreover, the surface film that formed on sputtered Mg–Ti based alloys in NaCl solution was thick, discontinuous and non-protective, whereas a thin, continuous and protective Mg and Ti oxide film was formed on a sputtered Ti–Mg based alloy.

36 MATERIALS SCIENCE↗

Conduction mechanism of sputtered BaTiO{sub 3} film on Ni substrate

BaTiO{sub 3} (BTO) thin film capacitors were deposited on Ni substrate using rf magnetron sputtering. Microstructural studies by x-ray diffraction and transmission electron microscopy reveal that the as-grown BTO films have the columnar structure and the good interface structure. Postdeposition anneal results in the recrystallization of BTO films. The electrical measurements exhibit that the BTO films have high capacitance densities and low leakage currents.

36 MATERIALS SCIENCE↗

Impact of Stoichiometry on Structural and Optical Properties of Sputter Deposited Multicomponent Tellurite Glass Films

Multicomponent TeO 2 –Bi 2 O 3 –ZnO ( TBZ ) glass thin films were prepared using RF magnetron sputtering under different oxygen flow rates. The influences of oxygen flow rate on the structural and optical properties of the resulting thin films were investigated. We observed that thin films sputtered in an oxygen‐rich environment are optically transparent while those sputtered in an oxygen‐deficient environment exhibit broadband absorption. The structural origin of the optical property variation was studied using X‐ray diffraction, X‐ray photoelectron spectroscopy, Raman Spectroscopy, and transmission electron microscopy which revealed that the presence of under‐coordinated Te leads to the observed optical absorption in oxygen‐deficient films.

Ogbuu, Okechukwu↗

Influence of sputtering power on structural, mechanical and photoluminescence properties of nanocrystalline SiC thin films

In the present study, SiC thin films were deposited on Si (100) substrate by magnetron sputtering using a 4N purity commercial SiC target in argon atmosphere. The effect of sputtering RF power (140-170W) on structural, mechanical and photoluminescence properties were systematically studied by X-ray diffraction, field emission scanning electron microscopy, Nanoindentation and Spectrophotometer respectively. X-ray diffraction shows polycrystalline 4H-SiC phase with (105) preferred orientation and an enhancement in crystallite size with increasing power was also observed. The decrement in hardness and Young’s modulus with increment in RF power was ascribed to Hall-Petch relation. The maximum hardness and Young’s modulus were found to be 32 GPa and 232 GPa respectively. The photoluminescence spectra show peaks at 384 nm (3.22 eV) which corresponds to bandgap of 4H-SiC (phonon assisted band to band recombination) and 416 nm (2.99 eV) may be attributed to defect states and intensity of both peaks decreases as power increases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electrochemical performance of CuO nanocrystal film fabricated by room temperature sputtering

Graphical abstract: High capacity of CuO thin film electrode for all-solid-state thin film batteries. Research highlights: {yields} Nanostructured CuO thin film is prepared by in situ sputtering. {yields} Excellent electrochemical performance with a very high capacity is achieved. {yields} Due to nanostructured grains, the in situ formed CuO possesses good cyclability. -- Abstract: To develop high performance anode materials for thin film batteries, copper oxide (CuO) film is fabricated at room temperature by reactive radio frequency magnetron sputtering. Morphological characterization shows that the CuO film consists of compacted CuO columnar grains of 20 nm in diameter and 200 nm in thickness. The measurement of lithium storage capacity and cyclability of the CuO film show that the first charge capacity of the film is 585 mAh g{sup -1} with an efficiency of 68.3% at a current density of 200 mA g{sup -1}. After the 50th cycle, the capacity retention remains as high as 97.4%. The nanostructured CuO film also shows a good rate capability even being cycled at 3000 mA g{sup -1} (5 C), demonstrating that the CuO film can be a promising material as an anode for high performance thin film batteries, especially for thin film battery with amorphous electrolyte.

36 MATERIALS SCIENCE↗

FMR and Magnetic Studies of RF-Sputtered Mn-Zn Ferrite Thin Films

The Manganese–Zinc ferrite (MZF) thin films were deposited on quartz substrates by radio frequency (RF) magnetron sputtering at 10 mTorr of argon gas pressure. The FMR and magnetization measurement were carried out to understand magnetic properties of the as-deposited and annealed MZF films. The resonance field (H{sub r}) of the FMR spectra shifts towards higher magnetic field when angle between applied field and thin film plane is changed from 0 to 90° indicating the existence of uniaxial anisotropy in the film. Whereas, H{sub r} shifts towards lower magnetic field with decrease in temperature of the film. This is due to ferrimagnetic ordering in the films at low temperatures. The magnetization versus field (M-H) plots reveal the soft ferrimagnetic behavior of the films. The post-deposition annealing of the film leads to increase in crystallite size with more uniform film surface and dense columnar growth compared to the as-deposited film. The increase in magnetization and decreases in H{sub r}-values compared to that of as-deposited film are observed for annealed film. The optical band gap of the film is also found to increase with annealing.

36 MATERIALS SCIENCE↗

Structural, magnetic, and transport properties of sputtered hexagonal MnNiGa thin films

We report on a systematical study of the structure, magnetism, and magnetotransport behavior of the hexagonal MnNiGa films deposited on thermally oxidized Si (001) substrates by magnetron sputtering. X-ray diffractions reveal that all the films deposited at different temperatures crystallized in hexagonal Ni{sub 2}In-type structure (space group P6{sub 3}/mmc). Scanning electron microscopy observations show that the surface morphology of the films varies with deposition temperature, and energy dispersive spectroscopy analysis shows compositions of the films remain nearly unchanged, independent of the deposition temperature. Magnetic measurements indicate that all films are ferromagnetic and exhibit a magnetic anisotropy behavior. The magnetoresistance (MR) exhibits a negative temperature- and field-dependent behavior. The possible origin of the negative MR is discussed. Furthermore, we found that the Hall effect is dominated by an anomalous Hall effect (AHE) only due to skew scattering independent of the deposition temperature of films. Moreover, the anomalous Hall resistivity presents a non-monotonously temperature-dependent behavior.

36 MATERIALS SCIENCE↗

Comprehensive characterization of CIGS absorber layers grown by one-step sputtering process

We have demonstrated that the use of a one-step sputtering process allowed for the fabrication of copper indium gallium diselenide (CIGS) thin films by RF magnetron sputtering without an additional selenization process. The CIGS thin films deposited at different substrate temperatures were synthesized on soda-lime glass (SLG) substrates using a single quaternary CIGS target. The film composition ratios of ([Cu]/[In]+[Ga]), ([Ga]/[In]+[Ga]), and ([Se]/[Cu]+[In]+[Ga]) were almost consistent with those of the sputtering target. X-ray diffraction (XRD) and Raman results showed that the crystallinity of the CIGS thin films was gradually improved as substrate temperatures increased. Transmission electron microscopy (TEM) showed that the films grown at 600 degrees C have a columnar structure with the grain size of ~100 nm. In addition, for the CIGS films grown at 600 degrees C, TEM-EDX analysis revealed that the synchronized fluctuation of the Cu and Se signals was observed in the direction of the film depth, while the In and Ga signals were constant. As a result, the CIGS solar cell made using the film showed a degraded cell efficiency of 2.5%, which might be have been caused by not only Cu-rich and Se-poor compositions but the locally unstable composition in the CIGS films fabricated by one-step sputtering.

14 SOLAR ENERGY↗

Effect of substrate temperature on structural and electrical properties of RF sputtered hafnium oxide thin films

In this work hafnium oxide thin films were deposited on p-type silicon substrate by Radio frequency magnetron sputtering at different substrate temperature ranging from room temperature to 300 °C. The structural and electrical properties of the sputtered films were investigated by x-ray diffraction, capacitance-voltage and current-voltage measurements. The XRD results show the formation monoclinic structure of the hafnium oxide thin films. The shifting of C-V curves towards negative voltage side depicts the increase in positive oxide charges with the rise of substrate temperature. Leakage current was found increased, when temperature enhanced from room temperature to 300 °C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Impact of B 4 C co-sputtering on structure and optical performance of Cr/Sc multilayer X-ray mirrors

We investigate the influence of B 4 C incorporation during magnetron sputter deposition of Cr/Sc multilayers intended for soft X-ray reflective optics. Chemical analysis suggests formation of metal: boride and carbide bonds which stabilize an amorphous layer structure, resulting in smoother interfaces and an increased reflectivity. A near-normal incidence reflectivity of 11.7%, corresponding to a 67% increase, is achieved at λ = 3.11 nm upon adding 23 at.% (B + C). The advantage is significant for the multilayer periods larger than 1.8 nm, where amorphization results in smaller interface widths, for example, giving 36% reflectance and 99.89% degree of polarization near Brewster angle for a multilayer polarizer. The modulated ion-energy-assistance during the growth is considered vital to avoid intermixing during the interface formation even when B + C are added.

36 MATERIALS SCIENCE↗

Electronic state of Er in sputtered AlN:Er films determined by magnetic measurements

The optoelectronic and piezoelectric properties of AlN:Er thin films have been of great recent interest for potential device applications. In this work, the focus is on the electronic state of Er in AlN:Er thin films prepared by reactive magnetron sputtering on (001) p-type Si substrate. X-ray diffraction shows that Er doping expands the lattice and the AlN:Er film has preferential c-plane orientation. To determine whether Er in AlN:Er is present as Er metal, Er{sub 2}O{sub 3}, or Er{sup 3+} substituting for Al{sup 3+}, detailed measurements and analysis of the temperature dependence (2 K–300 K) of the magnetization M at a fixed magnetic field H along with the M vs. H data at 2 K up to H = 90 kOe are presented. The presence of Er{sub 2}O{sub 3} and Er metal is ruled out since their characteristic magnetic transitions are not observed in the AlN:Er sample. Instead, the observed M vs. T and M vs. H variations are consistent with Er present as Er{sup 3+} substituting for Al{sup 3+} in AlN:Er at a concentration x = 1.08% in agreement with x = 0.94% ± 0.20% determined using x-ray photoelectron spectroscopy (XPS). The larger size of Er{sup 3+} vs. Al{sup 3+}explains the observed lattice expansion of AlN:Er.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗