Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LOW SPEED STABILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Strong-Drive Limits in Josephson Circuits: From Chaos to an Unbound-Resonance Threshold

Strong microwave drives enable fast measurement and parametric control in superconducting circuits but can induce transitions out of the intended low-energy manifold. We develop a unified description of strong-drive limits in flux- and charge-driven Josephson circuits across drive frequency and dc flux bias. Using classical phase-space analysis and Floquet--Markov simulations, we identify distinct low- and high-frequency mechanisms. At low frequency, we characterize bound-state resonances and separatrix chaos and find that the flux-drive chaos threshold depends strongly on dc flux bias. At high frequency, these mechanisms are suppressed, and the dissipative steady state transfers from the central bound-state sector to outer resonances formed by above-barrier running trajectories. The resulting unbound-resonance threshold is nearly independent of drive frequency and circuit parameters over the regime studied and is controlled primarily by dc flux bias. Coherent simulations show that parametric operation persists beyond this threshold, but at a reduced rate, setting an effective upper bound on the achievable operation speed. We derive analytical criteria for both thresholds, validate them numerically, and experimentally confirm the predicted dc-bias dependence of the low-frequency threshold in a flux-driven SQUID. We also determine the timescales for transfer into the unbound-resonance regime and relaxation back to the bound-state manifold after the drive is removed. Finally, we relate the stability limits to a complementary picture based on the junction critical current and extend the framework to multitone drives and inductively shunted circuits. Together, these results identify the mechanisms limiting strong driving and suggest routes to extend the stable operating range of Josephson circuits.

You, Xinyuan [Fermilab] (ORCID:0000000291789419)↗
NASA NTRS1992

Design of bearings for rotor systems based on stability

Design of rotor systems incorporating stable behavior is of great importance to manufacturers of high speed centrifugal machinery since destabilizing mechanisms (from bearings, seals, aerodynamic cross coupling, noncolocation effects from magnetic bearings, etc.) increase with machine efficiency and power density. A new method of designing bearing parameters (stiffness and damping coefficients or coefficients of the controller transfer function) is proposed, based on a numerical search in the parameter space. The feedback control law is based on a decentralized low order controller structure, and the various design requirements are specified as constraints in the specification and parameter spaces. An algorithm is proposed for solving the problem as a sequence of constrained 'minimax' problems, with more and more eigenvalues into an acceptable region in the complex plane. The algorithm uses the method of feasible directions to solve the nonlinear constrained minimization problem at each stage. This methodology emphasizes the designer's interaction with the algorithm to generate acceptable designs by relaxing various constraints and changing initial guesses interactively. A design oriented user interface is proposed to facilitate the interaction.

Dhar, D.↗
NASA NTRS1931

Effect of stabilizing forces on turbulence

The appearance of expressed discontinuity layers in the free atmosphere, where a warm air mass flows over a cold mass without perceptible intermingling forms the basis of the present report. In these experiments an air stream is to be blown between a water-cooled and a vapor-heated plate. According to what preceded it is anticipated that the exchange will be enhanced. Because these experiments had to be made at relatively low air speeds so as to let the lifting forces become effective, it first required a study of the test methods, and so we have not yet proceeded beyond the preliminary tests on the most suitable hot-wire connections and thermocouples for recording speed and temperature.

PRANDTL L↗
NASA NTRS2009

Towards an "All Speed" Unstructured Upwind Scheme

In the authors previous studies [1], a time-accurate, upwind finite volume method (ETAU scheme) for computing compressible flows on unstructured grids was proposed. The scheme is second order accurate in space and time and yields high resolution in the presence of discontinuities. The scheme features a multidimensional limiter and multidimensional numerical dissipation. These help to stabilize the numerical process and to overcome the annoying pathological behaviors of upwind schemes. In the present paper, it will be further shown that such multidimensional treatments also lead to a nearly all-speed or Mach number insensitive upwind scheme. For flows at very high Mach number, e.g., 10, local numerical instabilities or the pathological behaviors are suppressed, while for flows at very low Mach number, e.g., 0.02, computation can be directly carried out without invoking preconditioning. For flows in different Mach number regimes, i.e., low, medium, and high Mach numbers, one only needs to adjust one or two parameters in the scheme. Several examples with low and high Mach numbers are demonstrated in this paper. Thus, the ETAU scheme is applicable to a broad spectrum of flow regimes ranging from high supersonic to low subsonic, appropriate for both CFD (computational fluid dynamics) and CAA (computational aeroacoustics).

Loh, Ching Y.↗
NASA NTRS1981

Experimental and theoretical study of three interacting, closely-spaced, sharp-edged 60 deg delta wings at low speeds

Wind tunnel tests were conducted to determine the subsonic longitudinal aerodynamic characteristics of lifting configuration consisting of a 60 deg delta main wing with two smaller 60 deg delta wings (called sub-wings) attached underneath. The test was designed to determine the effects on lift, drag, and pitching moment due to various placement of the subwings in relation to the main wing. Test results indicate the increasing vertical separation between the main wing and the sub-wings produced the most significant results; a 23.1% increase in maximum lift coefficient, a reduction in drag coefficient at high lift coefficients, and an increase in longitudinal stability. Lateral separation of the sub-wings produced no significant changes. Placement of the sub-wings rearward increases the initial lift curve slope and maximum lift coefficient and also increase the longitudinal stability. Results of a computer study using a vortex lattice code supported the experimental conclusions.

Faery, H. F., Jr.↗
DOE OSTI2021

Universal scaling laws of keyhole stability and porosity in 3D printing of metals

Metal three-dimensional (3D) printing includes a vast number of operation and material parameters with complex dependencies, which significantly complicates process optimization, materials development, and real-time monitoring and control. We leverage ultrahigh-speed synchrotron X-ray imaging and high-fidelity multiphysics modeling to identify simple yet universal scaling laws for keyhole stability and porosity in metal 3D printing. The laws apply broadly and remain accurate for different materials, processing conditions, and printing machines. We define a dimensionless number, the Keyhole number, to predict aspect ratio of a keyhole and the morphological transition from stable at low Keyhole number to chaotic at high Keyhole number. Furthermore, we discover inherent correlation between keyhole stability and porosity formation in metal 3D printing. By reducing the dimensions of the formulation of these challenging problems, the compact scaling laws will aid process optimization and defect elimination during metal 3D printing, and potentially lead to a quantitative predictive framework.

42 ENGINEERING↗
NASA NTRS1983

Analogies between transitional and turbulent boundary layers

One of the interesting aspects of transitional and turbulent boundary layers is the development of counter-rotating streamwise vortices near the wall. The most regular pattern is found in a boundary layer on a concave wall where the generation mechanism is known to be the Goertler instability. The origin of these vortices in other translational and turbulent boundary layers is presently unknown. Since the counter-rotating vortices are located in a region of strong shear, low-speed fluid is pumped away from the wall which coalesces into regions of low momentum lying between the vortices. As this pumping action continues, localized inflectional velocity profiles become apparent in the transitional and turbulent boundary layers. The oscillations which develop upon these profiles scale with the local thickness and velocity difference in the same manner as the two-dimensional steady free shear layer stability problems. The oscillations grow to large amplitude and break down into new turbulence in both the transitional and turbulent boundary layers.

Blackwelder, R. F.↗
NASA NTRS1993

Low-speed wind tunnel test results of the Canard Rotor/Wing concept

The Canard Rotor/Wing (CRW), a high-speed rotorcraft concept, was tested at the National Aeronautics and Space Administration (NASA) Ames Research Center's 40- by 80-Foot Wind Tunnel in Mountain View, California. The 1/5-scale model was tested to identify certain low-speed, fixed-wing, aerodynamic characteristics of the configuration and investigate the effectiveness of two empennages, an H-Tail and a T-Tail. The paper addresses the principal test objectives and the results achieved in the wind tunnel test. These are summarized as: i) drag build-up and differences between the H-Tail and T-Tail configuration, ii) longitudinal stability of the H-Tail and T-Tail configurations in the conversion and cruise modes, iii) control derivatives for the canard and elevator in the conversion and cruise modes, iv) aerodynamic characteristics of varying the rotor/wing azimuth position, and v) canard and tail lift/trim capability for conversion conditions.

Bass, Steven M.↗
NASA NTRS1977

Finite element analysis of low speed viscous and inviscid aerodynamic flows

A weak interaction solution algorithm was established for aerodynamic flow about an isolated airfoil. Finite element numerical methodology was applied to solution of each of differential equations governing potential flow, and viscous and turbulent boundary layer and wake flow downstream of the sharp trailing edge. The algorithm accounts for computed viscous displacement effects on the potential flow. Closure for turbulence was accomplished using both first and second order models. The COMOC finite element fluid mechanics computer program was modified to solve the identified equation systems for two dimensional flows. A numerical program was completed to determine factors affecting solution accuracy, convergence and stability for the combined potential, boundary layer, and parabolic Navier-Stokes equation systems. Good accuracy and convergence are demonstrated. Each solution is obtained within the identical finite element framework of COMOC.

Baker, A. J.↗
NASA NTRS1989

Simulation evaluation of transition and hover flying qualities of a mixed-flow, remote-lift STOVL aircraft

Using a generalized simulation model developed for piloted evaluations of STOVL aircraft, an initial fixed-base simulation of a mixed-flow, remote-lift configuration has been completed. Objectives were to evaluate the integration of the aircraft's flight and propulsion controls to achieve good flying qualities throughout the low-speed flight envelope; to determine control power used during transition, hover, and vertical landing; and to evaluate the transition flight envelope considering the influence of thrust deflection of the remote-lift component. Pilots' evaluations indicated that Level 1 flying qualities could be achieved for deceleration to hover in instrument conditions, for airfield landings, and for recovery to a small ship when attitude and velocity stabilization and command augmentation control modes were provided. Level 2 flying qualities were obtained for these same tasks when only the attitude command mode was used, leaving the pilot to perform the task of thrust management required to control the flight-path and speed in transition and the horizontal and vertical translational velocities in hover. Thrust margins were defined for vertical landing as a function of ground effect and hot-gas ingestion.

Franklin, James A.↗
NASA NTRS1959

Wind-Tunnel Investigation of Subsonic Longitudinal Aerodynamic Characteristics of a Tiltable-Wing Vertical-Take-Off-and-Landing Supersonic Bomber Configuration Including Turbojet Power Effects

Jet-powered model tests were made to determine the low-speed longitudinal aerodynamic characteristics of a vertical-take-off and-landing supersonic bomber configuration. The configuration has an unique engine-wing arrangement wherein six large turbojet engines (three on each side of the fuselage) are buried in a low-aspect-ratio wing which is tilted into the vertical plane for take-off. An essentially two-dimensional variable inlet, spanning the leading edge of each wing semispan, provides air for the engines. Jet flow conditions were simulated for a range of military (nonafterburner) and afterburner turbojet-powered flight at subsonic speeds. Three horizontal tails were tested at a station down-stream of the jet exit and at three heights above the jet axes. A semi-span model was used and test parameters covered wing-fuselage incidence angles from 0 deg to 15 deg, wing angles of attack from -4 deg to 36 deg, a variable range of horizontal-tail incidence angles, and some variations in power simulation conditions. Results show that, with all horizontal tails tested, there were large variations in static stability throughout the lift range. When the wing and fuselage were alined, the model was statically stable throughout the test range only with the largest tail tested (tail span of 1.25 wing span) and only when the tail was located in the low test position which placed the tail nearest to the undeflected jet. For transition flight conditions, none of the tail configurations provided satisfactory longitudinal stability or trim throughout the lift range. Jet flow was destabilizing for most of the test conditions, and varying the jet-exit flow conditions at a constant thrust coefficient had little effect on the stability of this model. Wing leading-edge simulation had some important effects on the longitudinal aerodynamic characteristics.

Thompson, Robert F.↗
NASA NTRS1977

The oblique wing - Aircraft design for transonic and low supersonic speeds

In tests at transonic speeds a conventional 'subsonic' wing turned at an oblique angle to the flow has demonstrated lift-drag ratios higher than conventional swept-back or delta wings. When returned to its straight position, perpendicular to the flow, such a wing would minimize the display of energy and noise in the airport environment. Following a brief review of theoretical and experimental results, the paper discusses various characteristics of the oblique wing as they relate to aircraft design. Topics covered are lift-drag ratio, flight control and trim and aeroelastic stability. The possibility of an all-wing aircraft for flight at Mach 2 is suggested.

Jones, R. T.↗
DOE OSTI2025

Tandem neural network-based controller for x-ray bimorph mirrors

Nanometer-scale shape control of x-ray mirrors is crucial for coherent x-ray beam experiments at low-emittance synchrotron beamline instruments. Piezoelectric bimorph mirrors offer adaptive control but are hindered by nonlinearities such as cross talk, creep, and hysteresis. To overcome these limitations, we present a novel feedback-free control solution, inspired by the proportional–integral–derivative (PID) scheme, driven by tandem neural networks (TNNs). Using task-specific datasets, the TNN-based system predicts actuator voltages with greater speed, accuracy, and stability than a single NN-based model. This approach is ideal for real-time applications, such as adapting beam focus to dynamic sample sizes while maintaining precise wavefront quality. Our findings highlight the potential of artificial intelligence in rapidly optimizing adaptive optics and managing nonlinear control systems.

Zhang, Runyu↗
NASA NTRS2006

AIRS Observations of DomeC in Antarctica and Comparison with Automated Weather Stations (AWS)

We compare the surface temperatures at Dome Concordia (DomeC) deduced from AIRS data and two Automatic Weather Stations at Concordia Station: AWS8989 , which has been in operation since December 1996, and AWS.it, for which data are available between January and November 2005. The AWS8989 readings are on average 3 K warmer than the AWS.it readings, with a warmer bias in the Antarctic summer than in the winter season. Although AIRS measures the skin brightness temperature, while the AWS reports the temperature of the air at 3 meter above the surface, the AIRS measurements agree well with the AWS.it readings for all data and separately for the summer and winter seasons, if data taken in the presence of strong surface inversions are filtered out. This can be done by deducing the vertical temperature gradient above the surface directly from the AIRS temperature sounding channels or indirectly by noting that extreme vertical gradients near the surface are unlikely if the wind speed is more than a few meters per second. Since the AIRS measurements are very well calibrated, the agreement with AWS.it is very encouraging. The warmer readings of AWS8989 are likely due to thermal contamination of the AWS8989 site by the increasing activity at Concordia Station. Data from an AWS.it quality station could be used for the evaluation of radiometric accuracy and stability of polar orbiting sounders at low temperatures. Unfortunately, data from AWS.it was available only for a limited time. The thermal contamination of the AWS8989 data makes long-term trends deduced from AWS8989 and possibly results about the rapid Antarctic warming deduced from other research stations on Antarctica suspect. AIRS is the first hyperspectral infrared sounder designed in support of weather forecasting and climate research. It was launched in May 2002 on the EOS Aqua spacecraft into a 704 km altitude polar sun-synchronous orbit. The lifetime of AIRS, estimated before launch to be at least 5 years is, based on the latest evaluation, limited by the amount of attitude control gas on the EOS Aqua spacecraft, which is expected to last through 2015.

atmospheric↗
NASA NTRS2014

Dual Fan Separator within the Universal Waste Management System

Since NASA's new spacecraft in development for both LEO and Deep Space capability have considerable crew volume reduction in comparison to the Space Shuttle, the need became apparent for a smaller commode. In response the Universal Waste Management System (UWMS) was designed, resulting in an 80% volume reduction from the last US commode, while enhancing performance. The ISS WMS and previous shuttle commodes have a fan supplying air flow to capture feces and a separator to capture urine and separate air from the captured air/urine mixture. The UWMS combined both rotating equipment components into a single unit, referred to at the Dual Fan Separator (DFS). The combination of these components resulted in considerable packaging efficiency and weight reduction, removing inter-component plumbing, individual mounting configurations and required only a single motor and motor controller, in some of the intended UWMS platform applications the urine is pumped to the ISS Urine Processor Assembly (UPA) system. It requires the DFS to include less than 2.00% air inclusion, by volume, in the delivered urine. The rotational speed needs to be kept as low as possible in centrifugal urine separators to reduce air inclusion in the pumped fluid, while fans depend on rotational speed to develop delivered head. To satisfy these conflicting requirements, a gear reducer was included, allowing the fans to rotate at a much higher speed than the separator. This paper outlines the studies and analysis performed to develop the DFS configuration. The studies included a configuration trade study, dynamic stability analysis of the rotating bodies and a performance analysis of included labyrinth seals. NASA is considering a program to fly the UWMS aboard the ISS as a flight experiment. The goal of this activity is to advance the Technical Readiness Level (TRL) of the DFS and determine if the concept is ready to be included as part of the flight experiment deliverable.

Stapleton, Tom↗
NASA NTRS2018

Surface Tension Containment Experiment (STCE) - Increasing Science Throughput on ISS

The Microgravity Science Glovebox (MSG) on the International Space Station (ISS) is used for fluid transfer in many types of experiments. Reagents are handled in the MSG to prevent their accidental release into the cabin. However, the MSG is currently over-subscribed, creating a backlog of users in flight. As a recourse, current experiments are underway to assess the possibility of moving certain science operations from the MSG into the open cabin of the ISS. The experiments are designed to assess the efficacy of exploiting surface tension as a control to prevent the unwanted release of liquids. Dyed water currently serves as an ersatz for potentially more hazardous liquids. Common wet-lab operations such as de/mating wetted Luer-Lok fittings, liquid-bearing container lid removal, and pipetting between well plates are performed illustrating the facility and challenges imposed by the microgravity environment. Concerning the latter, various pipette cannula sizes are deployed at various injection, withdrawal, and translations rates to map the existence, size, velocity, and trajectory of satellite droplets expected to form when breaking contact between the water surface and the pipette tip. Though such drops frequently form in terrestrial operations, they are nearly imperceptible and inconsequential—due in part to their speed and because gravity quickly returns them to the well plate from which they came. The use of airflow to capture and collect such satellite droplets is demonstrated. The dynamic stability of the liquid-filled well plates is quantified in response to a variety of crew-imparted disturbances. From a safety perspective, the results from the STCE are of immediate practical value. If such routine low-gravity capillary fluidic operations can be established as mundane, their performance may be moved out of the MSG and into the cabin, significantly increasing the efficiency of experiments performed on ISS.

Ungar, Eugene K.↗
NASA NTRS1984

Natural laminar flow airfoil design considerations for winglets on low-speed airplanes

Winglet airfoil section characteristics which significantly influence cruise performance and handling qualities of an airplane are discussed. A good winglet design requires an airfoil section with a low cruise drag coefficient, a high maximum lift coefficient, and a gradual and steady movement of the boundary layer transition location with angle of attack. The first design requirement provides a low crossover lift coefficient of airplane drag polars with winglets off and on. The other requirements prevent nonlinear changes in airplane lateral/directional stability and control characteristics. These requirements are considered in the design of a natural laminar flow airfoil section for winglet applications and chord Reynolds number of 1 to 4 million.

Vandam, C. P.↗
NASA NTRS1995

Nonlinear Propagating Features in the Stratosphere of Jupiter Generated by the Impact of SL-9

Among the more intriguing features observed by HST after the impacts of the fragments of Shoemaker-Levy 9 were rings, encircling several of the impact sites, that expanded radially at constant velocities of order 450-500 m/s. One credible suggestion has been that the rings are stratospheric manifestations of linear gravity waves seated in the troposphere (Ingersoll and Kanamori, 1995). In this scenario the waves are made visible by a condensible material of unknown composition. Based on simulations of the comet impact by Zahnle and Mac Low (1995), we suggest an alternative hypothesis, namely that the rings are nonlinear stratospheric gravity waves which break and entrain impact debris material in the breaking wave front. The computations produce just such a feature, with the nonlinear breaking wave front in the stratosphere propagating radially away from the impact site with the correct speed. The computed ring of material is located in an altitude region where the static stability profile has a local maximum and therefore forms a waveguide. Because entrained impact debris forms the ring feature in the model, a condensate of some unknown composition is not required in order to view the wave front. However, there is one severe problem with the computed nonlinear wave: in contrast to a linear wave, it slows down. The computed feature stops within 1000 seconds, while the observed feature lasted at least 10,000 seconds. Since the nonlinear breaking wave front is a natural product of our impact simulations, we are now investigating the conditions that will enable the breaking wave front to propagate further, in accord with the observations. The results of these computations will be presented.

Young, R. E.↗