Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “In Situ Measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Chapter 4: Vibrational Spectroscopy for Batteries

Dr. Sang-Don Han and Dr. Bertrand Tremolet de Villers describe infrared (IR) and Raman spectroscopy studies. Not only are the fundamental principles and measurement methods or FTIR and Raman presented, but also in situ spectroscopic analysis during battery cycling. The advantage of the in situ method is the additional insight into the chemical, thermal, and electrical mechanisms underlying the battery performance that are largely inaccessible with traditional ex situ measurements. The future perspectives on the continuing evolution of IR spectroscopy in electrochemical energy storage research are also presented.

battery↗
NASA NTRS1978

Geographical variations of NO and O3 in the lower stratosphere

Nitric oxide and ozone concentrations in the lower stratosphere have been measured from a high-altitude research aircraft using in situ measuring techniques. Results of several geographical surveys are presented along with predictions of two two-dimensional stratospheric models. Meridional and zonal data were obtained in June 1974 and in June, July, and August 1975. At longitudes 122-158 deg W the meridional data taken between 5 and 80 deg N latitude show an increasing NO concentration with latitude, by a factor of 4 at 21-km altitude and a less marked increase at 18 km. The minimum NO concentration at 21 km is observed at 5 deg N latitude and is about 6 x 10 to the 8th power/cu cm. Zonal data at latitudes 22-38 deg N taken from 55 to 176 deg N longitude show little variation of the NO and O3 concentrations with longitude.

Loewenstein, M.↗
NASA NTRS1981

Satellite altimetric measurements of the ocean. Report of the TOPEX Science Working Group

The scientific usefulness of satellite measurements of ocean topography for the study of ocean circulation was investigated. The following topics were studied: (1) scientific problems which use altimetric measurements of ocean topography; (2) the extent in which in situ measurements are complementary or required; (3) accuracy, precision, and spatial and temporal resolutions which are required of the topographic measurements; (4) errors associated with measurement techniques; and (5) influences of these errors on scientific problems. An operational system for measuring ocean topography, was defined and the cost of conducting such a topographic experiment, was estimated.

Stewart, R.↗
NASA NTRS2004

Parametric Study for Increasing On-Station Duration via Unconventional Aircraft Launch Approach

The need for better atmospheric predictions is causing the atmospheric science community to look for new ways to obtain longer, higher-resolution measurements over several diurnal cycles. The high resolution, in-situ measurements required to study many atmospheric phenomena can be achieved by an Autonomous Aerial Observation System (AAOS); however, meeting the long on-station time requirements with an aerial platform poses many challenges. Inspired by the half-scale drop test of the deployable Aerial Regional-scale Environmental Survey (ARES) Mars airplane, a study was conducted at the NASA Langley Research Center to examine the possibility of increasing on-station time by launching an airplane directly at the desired altitude. The ARES Mars airplane concept was used as a baseline for Earth atmospheric flight, and parametric analyses of fundamental configuration elements were performed to study their impact on achieving desired on-station time with this class of airplane. The concept involved lifting the aircraft from the ground to the target altitude by means of an air balloon, thereby unburdening the airplane of ascent requirements. The parameters varied in the study were aircraft wingspan, payload, fuel quantity, and propulsion system. The results show promising trends for further research into aircraft-payload design using this unconventional balloon-based launch approach.

Kuhl, Christopher A.↗
NASA NTRS2010

Current and Near-Term Future Measurements of the Orbital Debris Environment at NASA

The NASA Orbital Debris Program Office places great emphasis on obtaining and understanding direct measurements of the orbital debris environment. The Orbital Debris Program Office's environmental models are all based on these measurements. Because OD measurements must cover a very wide range of sizes and altitudes, one technique realistically cannot be used for all measurements. In general, radar measurements have been used for lower altitudes and optical measurements for higher altitude orbits. For very small debris, in situ measurements such as returned spacecraft surfaces are utilized. In addition to receiving information from large debris (> 5-10 cm diameter) from the U.S. Space Surveillance Network, NASA conducts statistical measurements of the debris population for smaller sizes. NASA collects data from the Haystack and Goldstone radars for debris in low Earth orbit as small as 2- 4 mm diameter and from the Michigan Orbital DEbris Survey Telescope for debris near geosynchronous orbit altitude for sizes as small as 30-60 cm diameter. NASA is also currently examining the radiator panel of the Hubble Space Telescope Wide Field Planetary Camera 2 which was exposed to space for 16 years and was recently returned to Earth during the STS- 125 Space Shuttle mission. This paper will give an overview of these on-going measurement programs at NASA as well as discuss progress and plans for new instruments and techniques in the near future.

Stansbery, Gene↗
NASA NTRS2014

Column CO2 Measurement From an Airborne Solid-State Double-Pulsed 2-Micron Integrated Path Differential Absorption Lidar

NASA LaRC is developing and integrating a double-Pulsed 2-micron direct detection IPDA lidar for CO2 column measurement from an airborne platform. The presentation will describe the development of the 2-micrometers IPDA lidar system and present the airborne measurement of column CO2 and will compare to in-situ measurement for various ground target of different reflectivity.

Singh, U. N.↗
NASA NTRS2014

Airborne 2-Micron Double-Pulsed Integrated Path Differential Absorption Lidar for Column CO2 Measurement

Double-pulse 2-micron lasers have been demonstrated with energy as high as 600 millijouls and up to 10 Hz repetition rate. The two laser pulses are separated by 200 microseconds and can be tuned and locked separately. Applying double-pulse laser in DIAL system enhances the CO2 measurement capability by increasing the overlap of the sampled volume between the on-line and off-line. To avoid detection complicity, integrated path differential absorption (IPDA) lidar provides higher signal-to-noise ratio measurement compared to conventional range-resolved DIAL. Rather than weak atmospheric scattering returns, IPDA rely on the much stronger hard target returns that is best suited for airborne platforms. In addition, the IPDA technique measures the total integrated column content from the instrument to the hard target but with weighting that can be tuned by the transmitter. Therefore, the transmitter could be tuned to weight the column measurement to the surface for optimum CO2 interaction studies or up to the free troposphere for optimum transport studies. Currently, NASA LaRC is developing and integrating a double-Pulsed 2-micron direct detection IPDA lidar for CO2 column measurement from an airborne platform. The presentation will describe the development of the 2-micron IPDA lidar system and present the airborne measurement of column CO2 and will compare to in-situ measurement for various ground target of different reflectivity.

Singh, Upendra N.↗
NASA NTRS2015

4STAR Sky-Scanning Retrievals of Aerosol Intensive Optical Properties from Multiple Field Campaigns with Detailed Comparisons of SSA Reported During SEAC4RS

The 4STAR (Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research) instrument combines airborne sun tracking capabilities of the Ames Airborne Tracking Sun Photometer (AATS-14) with AERONET-like sky-scanning capability and adds state-of-the-art fiber-coupled grating spectrometry to yield hyper spectral measurements of direct solar irradiance and angularly resolved sky radiance. The combination of sun-tracking and sky-scanning capability enables retrievals of wavelength-dependent aerosol optical depth (AOD), mode-resolved aerosol size distribution (SD), asphericity, and complex refractive index, and thus also the scattering phase function, asymmetry parameter, single-scattering albedo (SSA), and absorption aerosol optical thickness (AAOT).From 2012 to 2014 4STAR participated in four major field campaigns: the U.S. Dept. of Energy TCAP I II campaigns, and NASAs SEAC4RS and ARISE campaigns. Establishing a strong performance record, 4STAR operated successfully on all flights conducted during each of these campaigns. Sky radiance spectra from scans in either constant azimuth (principal plane) or constant zenith angle (almucantar) were interspersed with direct beam measurements during level legs. During SEAC4RS and ARISE, 4STAR airborne measurements were augmented with flight-level albedo from the collocated Shortwave Spectral Flux Radiometer (SSFR) providing improved specification of below-aircraft radiative conditions for the retrieval. Calibrated radiances and retrieved products will be presented with particular emphasis on detailed comparisons of ambient SSA retrievals and measurements during SEAC4RS from 4STAR, AERONET, HSRL2, and from in situ measurements.

Flynn, Connor↗
NASA NTRS2021

Chemical Reactivity of In-Situ Lunar Dust for Biotoxicity Assessment

How does the chemical reactivity of in-situ lunar dust compare to Apollo samples currently stored in curation facilities here on Earth? Essential investigations of this question will help us to further mitigate exploration risks for future human explorers on the Moon and will also provide critical information for astrobiologists and space biologists using the Moon for scientific inquiry. Apollo 14 dust biotoxicity studies, carried out by the NASA Lunar Airborne Dust Toxicity Assessment Group (LADTAG), included numerous cellular and animal experiments. Intratracheal instillation and inhalation studies in rats both showed Apollo 14 dust to be intermediate in toxicity compared to low-tox titanium dusts and high-tox quartz dusts of similar particle sizes. The collective results were used in models to establish a safe exposure limit for astronauts. Although LADTAG took extensive steps to preserve what chemical reactivity may still have existed in the samples, it is simply unknown if they possessed true in-situ chemical reactivity or if that reactivity has decayed. Initial gas loss on collection and other alterations, and even intermittent exposure to Earth-normal conditions during subsequent decades of handling, obscure a forensic reconstruction of the initial state. Because a mineral dust’s chemical reactivity influences its biotoxicity, researchers have developed methods to “activate” lunar dust and simulants. Past studies that modeled impact processes and radiation in the lunar environment suggest that in-situ lunar dust is likely to be more chemically reactive than Earth-exposed samples. Because of these results, in-situ measurements are warranted. Since the lunar surface is heterogeneous, dust biotoxicity is expected to vary from site to site due to particle size, mineralogy, physical characteristics, degree of space weathering, and chemical reactivity. This circumstance dictates dust assessments at a suite of lunar sites enabled by CLPS opportunities. Dose, location, and duration of particle exposure will also affect biological responses. In-situ chemical reactivity measurements can inform cross-cutting collaborative research campaigns such as astrobiology studies examining regolith interactions with organisms and its ability to preserve chemical and structural biomarkers, as well as space biology investigations that examine regolith-microbe interactions relating to life support systems, plant growth, biomining, and development of regolith biocomposites.

Jon C Rask↗
NASA NTRS2013

Atmospheric CO2 Column Measurements with an Airborne Intensity-Modulated Continuous-Wave 1.57-micron Fiber Laser Lidar

The 2007 National Research Council (NRC) Decadal Survey on Earth Science and Applications from Space recommended Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS) as a mid-term, Tier II, NASA space mission. ITT Exelis, formerly ITT Corp., and NASA Langley Research Center have been working together since 2004 to develop and demonstrate a prototype Laser Absorption Spectrometer for making high-precision, column CO2 mixing ratio measurements needed for the ASCENDS mission. This instrument, called the Multifunctional Fiber Laser Lidar (MFLL), operates in an intensity-modulated, continuous-wave mode in the 1.57- micron CO2 absorption band. Flight experiments have been conducted with the MFLL on a Lear-25, UC-12, and DC-8 aircraft over a variety of different surfaces and under a wide range of atmospheric conditions. Very high-precision CO2 column measurements resulting from high signal-to-noise (great than 1300) column optical depth measurements for a 10-s (approximately 1 km) averaging interval have been achieved. In situ measurements of atmospheric CO2 profiles were used to derive the expected CO2 column values, and when compared to the MFLL measurements over desert and vegetated surfaces, the MFLL measurements were found to agree with the in situ-derived CO2 columns to within an average of 0.17% or approximately 0.65 ppmv with a standard deviation of 0.44% or approximately 1.7 ppmv. Initial results demonstrating ranging capability using a swept modulation technique are also presented.

Dobler, Jeremy T.↗
NASA NTRS2014

Airborne In-Situ Trace Gas Measurements of Multiple Wildfires in California (2013-2014)

Biomass burning emissions are an important source of a wide range of trace gases and particles that can impact local, regional and global air quality, climate forcing, biogeochemical cycles and human health. In the western US, wildfires dominate over prescribed fires, contributing to atmospheric trace gas budgets and regional and local air pollution. Limited sampling of emissions from wildfires means western US emission estimates rely largely on data from prescribed fires, which may not be a suitable proxy for wildfire emissions.We report here in-situ measurements of carbon dioxide, methane, ozone and water vapor from the plumes of a variety of wildfires sampled in California in the fire seasons of 2013 and 2014. Included in the analysis are the Rim Fire (August October 2013, near Yosemite National Park), the Morgan Fire (September 2013, near Clayton, CA), and the El Portal Fire (July August 2014, in Yosemite National Park), among others. When possible, fires were sampled on multiple days.Emission ratios and estimated emission factors will be presented and discussed in the context of fuel composition, plume structure, and fire phase. Correlations of plume chemical composition to MODISVIIRS Fire Radiative Power (FRP) and other remote sensing information will be explored. Furthermore, the role of plumes in delivery of enhanced ozone concentrations to downwind municipalities will be discussed.

Gas↗
DOE OSTI2026

In situ quantification of fracture slip induced by hydraulic injections in a deep borehole: A comparison of two different borehole techniques

In situ measurements of fracture deformation during fluid injection are rare, yet essential for understanding the mechanical response of fractured rock. In this study, we evaluate the reliability of two methods by comparing their slip vector estimates: high-resolution borehole acoustic televiewer images captured before and after injection tests, and displacement data from a three-component borehole deformation probe recorded during the injections. Acoustic televiewer images capture only final in-plane displacement, whereas three-component borehole deformation measurements provide full 3D, transient fracture movement. Four injection tests in a fractured granitic rock mass along an inclined borehole at the Bedretto Underground Laboratory (Switzerland), beneath more than 1100 m of overburden, were analyzed. The two methods yielded consistent kinematics and comparable slip magnitudes, typically in the range of 0.2 – 0.6 mm. Angular differences between estimated slip directions ranged from 0.2° to 28°. For two test intervals with pre-existing fractures optimally oriented for slip, the measured slip vectors agreed with forward-modeled slip vectors based on the regional in situ stress field, supporting the Wallace–Bott hypothesis. Measurable shear displacement was identified in two test intervals containing fractures oriented nearly perpendicular to the least principal stress, including a newly formed hydraulic fracture. This demonstrates that even fractures unfavorably oriented for slip can undergo shear due to local stress perturbations around an inclined borehole.

Acoustic televiewer↗
NASA NTRSDate not supplied

First in-situ Nitrogen Isotope Measurements in Martian Meteorites

The origin and timing of the accretion of volatile elements on the terrestrial planets remains a subject of controversy. Nitrogen and hydrogen isotopes are powerful tools to constrain the source(s) of primordial volatiles accreted by planetary bodies because their isotope ratios (15N/14N; D/H) differ significantly between different solar system reservoirs (e.g., solar, chondritic, cometary). Hf-W data of martian samples indicate that Mars accreted very rapidly in the inner solar system and reached half ofits size in 1.8 Myr [1]. Therefore, martian samples are key to understand the distribution of volatile elements in the inner solar system during the early stages of planetary formation. Since no space missions have yet returned samples from Mars, martian meteorites (Shergottites, Nakhlites, Chassignites) are unique samples to constrain the source(s) of volatiles present in the martian mantle. The goal of this study was to target pristine phases(e.g., melt inclusions, mesostasis) for in-situ measurements of their nitrogen content and isotopic ratios to access the most primitive melt of the Chassignites and Nakhlites reservoirs. Five different Nakhlites (Nakhla, NWA 998, MIL 03346, Y 000593,NWA 6148) and Chassigny were analysed [2] using a recent high-resolution analytical technique that allows constraining the nitrogen composition of both carbon-bearing and carbon-free phases in natural and synthetic samples. Nitrogen was measured in the form of 14N16O- and 15N16O- with the CAMECA 1280-HR2 at the CRPG [3]. A significant amount of nitrogen was detected in melt inclusions in Chassigny and in the mesostasis of Nakhla, Y000593, MIL 03346, and NWA 6148. Nitrogen isotope signatures of Chassigny and Nakhlites exhibit a heavy isotope enrichment compared to Earth's mantle, and are consistent with a carbonaceous chondrite-like source [4]. This suggests that Earth and Mars accreted nitrogen from different chondritic sources. Overall, our in-situ technique is a unique and powerful tool to characterize the nitrogen abundance and isotopic composition of natural samples.

C Deligny↗
NASA NTRS1988

Insitu measurement and control of processing properties of composite resins in a production tool

An in situ measuring technique for use in automated composite processing and quality control is discussed. Frequency dependent electromagnetic sensors are used to measure processing parameters at four ply positions inside a thick section 192-ply graphite-epoxy composite during cure in an 8 x 4 in. autoclave. Viscosity measurements obtained using the sensors are compared with the viscosities calculated using the Loos-Springer cure process model. Good overall agreement is obtained. In a subsequent autoclave run, the output from the four sensors was used to control the autoclave temperature. Using the 'closed loop' sensor controlled autoclave temperature resulted in a more uniform and more rapid cure cycle.

Kranbuehl, D.↗
NASA NTRS1991

A new probe for measuring small electric fields in plasmas

A dipolar double probe has been developed for in situ measurements of small electric fields in laboratory plasmas. The probe measures dc to ac electric fields (f values between 0 and 20 MHz) with high sensitivity (Emin about 10 microV/cm) and responds to both space charge electric fields and inductive electric fields. Using voltage-to-frequency conversion, the probe signal is obtained free of errors and loading effects by a transmission line. Various examples of useful applications for the new probe are presented, such as measurements of dc ambipolar fields, ac space-charge fields of ion acoustic waves, ac inductive fields of whistler waves, and mixed inductive and space-charge electric fields in current-carrying magnetoplasmas.

Stenzel, R. L.↗
NASA NTRS2008

Measurements of Trace Gases in the Tropical Tropopause Layer

A unique dataset of airborne in situ observations of HCl, O3, HNO3, H2O, CO, CO2 and CH3Cl has been made in and near the tropical tropopause layer (TTL). A total of 16 profiles across the tropopause were obtained at latitudes between 10degN and 3degs from the NASA WB-57F high-altitude aircraft flying from Costa Rica. Few in situ measurements of these gases, particularly HCl and HNO3, have been reported for the TTL. The general features of the trace gas vertical profiles are consistent with the concept of the TTL as distinct from the lower troposphere and lower stratosphere. A combination of the tracer profiles and correlations with O3 is used to show that a measurable amount of stratospheric air is mixed into this region. The HCl measurements offer an important constraint on stratospheric mixing into the TTL because once the contribution from halocarbon decomposition is quantified, the remaining HCl (>60% in this study) must have a stratospheric source. Stratospheric HCl in the TTL brings with it a proportional amount of stratospheric O3. Quantifying the sources of O3 in the TTL is important because O3 is particularly effective as a greenhouse gas in the tropopause region.

Marcy, T. P.↗
DOE OSTI2022

Harmonizing solar induced fluorescence across spatial scales, instruments, and extraction methods using proximal and airborne remote sensing: A multi-scale study in a soybean field

Solar-induced chlorophyll fluorescence (SIF) has been widely used to track vegetation photosynthesis at different scales ranging from in-situ measurements to satellite products. Airborne platforms sample SIF data at a spatial scale intermediate between in-situ and satellite, matching that of ground measurement (e.g. flux tower footprints and other field sampling), enabling us to explore causes of SIF variation and validate satellite-based SIF products. However, harmonizing SIF across sensors and platforms (correcting for systematic errors to yield a consistent, comparable SIF product) is challenging because SIF can be retrieved in different absorption windows, with different instruments and methods complicating the comparison between different observational levels (i.e., ground, airborne, satellites) and between sites equipped with different instruments with varying optical properties (spectral resolution and sampling intervals, spatial resolution). Additionally, the spatial and temporal variability of atmospheric properties can influence the retrieval of the weak SIF signal. Because of these complications, direct comparisons of airborne and ground SIF across scales are rarely attempted. Here, in this study, we combined airborne SIF data with simultaneous ‘ground truth’ data collected by stationary and mobile platforms in a soybean field in Nebraska, USA. In this effort, we tested several SIF extraction methods, including Fraunhofer Line Discrimination (FLD), improved Fraunhofer Line Discrimination (iFLD), Spectral Fitting Method (SFM), SpecFit, and a Singular Vector Decomposition (SVD) method. The SpecFit method was sensitive to the 715–740 nm water bands and removing the water bands in the fitting process yielded better agreement between the airborne and ground SIF spectra. Accurate estimation of the ground level downwelling irradiance obtained by ground measurements over a calibration target improved agreement between airborne and ground SIF retrievals at the O 2 A band, and allowed us to derive a SIF dataset with improved agreement across platforms and sampling scales. This experimental approach provided a method for generating comparable SIF signals across instruments, methods and platforms, which is critical to understanding the SIF-GPP relationship at different scales and to cross-validate the diversity of platforms used for satellite products calibration and validation.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2015

Establishing a Disruptive New Capability for NASA to Fly UAV's into Hazardous Conditions

A 2015 NASA Aeronautics Mission "Seedling" Proposal is described for a Severe-Environment UAV (SE-UAV) that can perform in-situ measurements in hazardous atmospheric conditions like lightning, volcanic ash and radiation. Specifically, this paper describes the design of a proof-of-concept vehicle and measurement system that can survive lightning attachment during flight operations into thunderstorms. Elements from three NASA centers draw together for the SE-UAV concept. 1) The NASA KSC Genesis UAV was developed in collaboration with the DARPA Nimbus program to measure electric field and X-rays present within thunderstorms. 2) A novel NASA LaRC fiber-optic sensor uses Faraday-effect polarization rotation to measure total lightning electric current on an air vehicle fuselage. 3) NASA AFRC's state-of-the-art Fiber Optics and Systems Integration Laboratory is envisioned to transition the Faraday system to a compact, light-weight, all-fiber design. The SE-UAV will provide in-flight lightning electric-current return stroke and recoil leader data, and serve as a platform for development of emerging sensors and new missions into hazardous environments. NASA's Aeronautics and Science Missions are interested in a capability to perform in-situ volcanic plume measurements and long-endurance UAV operations in various weather conditions. (Figure 1 shows an artist concept of a SE-UAV flying near a volcano.) This paper concludes with an overview of the NASA Aeronautics Strategic Vision, Programs, and how a SE-UAV is envisioned to impact them. The SE-UAV concept leverages high-value legacy research products into a new capability for NASA to fly a pathfinder UAV into hazardous conditions, and is presented in the SPIE DSS venue to explore teaming, collaboration and advocacy opportunities outside NASA.

Ely, Jay↗