Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Impact testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Hypervelocity Impact (HVI): WLE Small-Scale Fiberglass Panel Flat Target C-2 - Volume 4

During 2003 and 2004, the Johnson Space Center's White Sands Testing Facility in Las Cruces, New Mexico conducted hypervelocity impact tests on the space shuttle wing leading edge. Hypervelocity impact tests were conducted to determine if Micro-Meteoroid/Orbital Debris impacts could be reliably detected and located using simple passive ultrasonic methods. The objective of Target C-2 was to study impacts through the reinforced carboncarbon (RCC) panels of the Wing Leading Edge. Fiberglass was used in place of RCC in the initial tests. Impact damage was detected using lightweight, low power instrumentation capable of being used in flight.

Gorman, Michael R.↗
NASA NTRS2007

Hypervelocity Impact (HVI): WLE Small-Scale Fiberglass Panel Flat Target C-1 - Volume 3

During 2003 and 2004, the Johnson Space Center's White Sands Testing Facility in Las Cruces, New Mexico conducted hypervelocity impact tests on the space shuttle wing leading edge. Hypervelocity impact tests were conducted to determine if Micro-Meteoroid/Orbital Debris impacts could be reliably detected and located using simple passive ultrasonic methods. The objective of Target C-1 was to study hypervelocity impacts on the reinforced carbon-carbon (RCC) panels of the Wing Leading Edge. Fiberglass was used in place of RCC in the initial tests. Impact damage was detected using lightweight, low power instrumentation capable of being used in flight.

Gorman, Michael R.↗
NASA NTRSDate not supplied

A Comparative Analysis of Occupant Response Between Component and Full Vehicle Tests of Fokker F28 Aircraft Hardware

In 2019, the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) conducted a full-scale crash test of a Fokker F28 MK1000 aircraft. This test concluded a multi-year research effort in which two component fuselage sections of a matching Fokker F28 aircraft were previously tested under similar vertical impact conditions. Due to facility and cost constraints of full-scale testing, aircraft are typically evaluated through component level tests (i.e. vertical drops of fuselage subsections or isolated seat tests). Although more practical, these tests are limited in their ability fully replicate the complex multi-axis loading environment induced on the occupants during a full-aircraft crash event. Because of this, there is risk that component level testing does not provide a complete assessment of vehicle crashworthiness. Comparative analysis between full-scale and component level testing of the Fokker F28 aircraft provides an excellent opportunity to evaluate differences in crashworthiness prediction made between these levels of test fidelity. In this study, Anthropomorphic Test Device (ATD, a.k.a crash test dummies) responses measured during the Fokker full scale impact test were compared to those measured in the component fuselage section drops. A variety of ATD configurations (5th, 50th, 95th) and positions (upright, braced) were tested in both the full-scale and component tests. ATD injury metric response comparisons were made across these ATD variations in addition to comparisons made with respect to ATD location within the vehicle. Results found the addition of horizontal impact velocity, achieved in the full-scale testing, along with aircraft structural effects altered ATD based crashworthiness assessment of the vehicle.

Crashworthiness↗
NASA NTRS1992

Test and analysis results for composite transport fuselage and wing structures

Automated tow placement (ATP) and stitching of dry textile composite preforms followed by resin transfer molding (RTM) are being studied as cost effective manufacturing processes for obtaining damage tolerant fuselage and wing structures for transport aircraft. Data are presented to assess the damage tolerance of ATP and RTM fuselage elements with stitched-on stiffeners from compression tests of impacted three J-stiffened panels and from stiffener pull-off tests. Data are also presented to assess the damage tolerance of RTM wing elements which had stitched skin and stiffeners from impacted single stiffener and three blade stiffened compression tests and stiffener pull-off tests.

Deaton, Jerry W.↗
NASA NTRS1984

SRB/FWC water impact: Flexible body loads test

Two technical areas were examined: evaluation of potential correction methods for spurious case strain outputs from the pressure transducers during the NSWC tests; and assessing procedures for modifying either the excitation function or the response function to account for hydroelastic effects.

Source record↗
NASA NTRS1984

SRB/FWC water impact: Flexible body loads test

The modeling of the cavity collapse pressure loading is discussed. There are excellent high speed color films of the quarter scale model during cavity collapse. In these films, it is possible to see a very clearly defined pressure wave front propagating circumferentially around the vehicle that seems to be associated at least on the lee side with an abrupt rise in pressure at each pressure transducer. By using a motion analyzer and stepping through the films, the location of this wave front is tracted at a number of time intervals for drops 17 through 21. The entry conditions and average wave front velocity are shown. Mathematical formulae aid in the reconstruction of the spatial distribution of the pressure.

Source record↗
NASA NTRS2017

Validation Testing of a Peridynamic Impact Damage Model Using NASA's Micro-Particle Gun

Through a collaborative effort between the Virginia Commonwealth University and Raytheon, a peridynamic model for sand impact damage has been developed1-3. Model development has focused on simulating impacts of sand particles on ZnS traveling at velocities consistent with aircraft take-off and landing speeds. The model reproduces common features of impact damage including pit and radial cracks, and, under some conditions, lateral cracks. This study focuses on a preliminary validation exercise in which simulation results from the peridynamic model are compared to a limited experimental data set generated by NASA's recently developed micro-particle gun (MPG). The MPG facility measures the dimensions and incoming and rebound velocities of the impact particles. It also links each particle to a specific impact site and its associated damage. In this validation exercise parameters of the peridynamic model are adjusted to fit the experimentally observed pit diameter, average length of radial cracks and rebound velocities for 4 impacts of 300 μm glass beads on ZnS. Results indicate that a reasonable fit of these impact characteristics can be obtained by suitable adjustment of the peridynamic input parameters, demonstrating that the MPG can be used effectively as a validation tool for impact modeling and that the peridynamic sand impact model described herein possesses not only a qualitative but also a quantitative ability to simulate sand impact events.

Baber, Forrest E.↗
NASA NTRS1992

Test and analysis results for composite transport fuselage and wing structures

Automated tow placement (ATP) and stitching of dry textile composite preforms followed by resin transfer molding (RTM) are being investigated by researchers at NASA LaRC and Douglas Aircraft Company as cost-effective manufacturing processes for obtaining damage tolerant fuselage and wing structures for transport aircraft. The Douglas work is being performed under a NASA contract entitled 'Innovative Composites Aircraft Primary Structures (ICAPS)'. Data are presented in this paper to assess the damage tolerance of ATP and RTM fuselage elements with stitched-on stiffeners from compression tests of impacted three-J-stiffened panels and from stiffener pull-off tests. Data are also presented to assess the damage tolerance of RTM wing elements which had stitched skin and stiffeners from impacted single stiffener and three blade-stiffened compression tests and stiffener pull-off tests.

Deaton, Jerry W.↗
NASA NTRS2019

An Astronaut's Risk of Experiencing a Critical Impact from Lunar Ejecta During Lunar EVA

The Moon is under constant bombardment by meteoroids. When the meteoroid is large, the impact craters the surface, launching crater ejecta far from the impact potentially threatening astronauts on the lunar surface. In the early 1960’s, the ejecta impact flux was thought no more than the sporadic meteoroid flux but with speeds one to two orders of magnitude smaller. However, the Lunar Module designers realized by 1965 that meteoroid bumpers do not perform well at the smaller ejecta impact speeds. Their estimates of the Lunar Module risk of penetration by ejecta were 25 to 50% of the total risk. This was in spite of the exposure time to ejecta being only a third of that to sporadic meteoroids. The standard committee based the 1969 NASA SP-8013 lunar ejecta environment on Zook’s 1967 flux analysis and Gault, Shoemaker and Moore’s 1963 test data for impacts into solid basalt targets. However, Zook noted in his 1967 analysis, that if the lunar surface was composed of soil, that the ejected soil particles would be smaller than ejected basalt fragments and that the ejection speeds would be smaller. Both effects contribute to reducing the risk of a critical failure due to lunar ejecta. The authors revised Zook’s analysis to incorporate soil particle size distributions developed from analysis of Apollo lunar soil samples and ejected mass as a function of ejecta speed developed from coupling parameter analyses of soil impact-test data. The authors estimated EVA risk by assuming failure occurs at a critical impact energy. At these impact speeds, this might be true for suit hard and soft goods. However, these speeds are small enough that there may be significant strength effects that require new test data to modify the hypervelocity critical energy failure criterion. With these caveats, Christiansen, Cour-Palais and Freisen list the critical energy of the ISS EMU hard upper torso as 44 J and the helmet and visor as 71 J at hypervelocity. The authors then assumed that the lunar EVA suit fails at 50 J critical energy. This results in a 1,700,000 years mean time to failure using the results of this analysis and a 3,800 years mean time to failure using NASA SP-8013.

Bjorkman, Michael D.↗
NASA NTRS1961

Effect of a Load-Alleviating Structure on the Landing Behavior of a Reentry-Capsule Model

Model tests have been made to determine the landing-impact characteristics of a parachute-supported reentry capsule that had a compliable metal structure as a load-alleviating device. A 1/6-scale dynamic model having compliable aluminum-alloy legs designed to give a low onset rate of acceleration on impact was tested at flight-path angles of 90 degrees ( vertical ) and 35 deg, at a vertical velocity of 30 ft/sec ( full scale), and at contact attitudes of 0 deg and +/-30 deg. Landings were made on concrete, sand, and water. The maximum acceleration encountered was approximately 35g and the maximum onset rate was 2,000 g/sec. on concrete a t the 55 deg flight-path, f30 contact-attitude conditions; therefore, load-alleviating devices on the canister end of the model would be required. To evaluate the scaling characteristics of compliable metal structures, models were tested with 1/4.1-scale and full-scale aluminum-alloy legs. The maximum vertical accelerations and strokes obtained from tests of the 1/4.1-scale and full-scale legs were the same within the recording accuracy of the equipment. Acceleration time histories for the 90 degree flight-path, 0 deg contact-attitude condition were computed and are in good agreement with the experimental results.

Hoffman, Edward L.↗
NASA NTRS1961

Effect of Load-Alleviating Structure on the Landing Behavior of a Reentry-Capsule Model

Model tests have been made to determine the landing-impact characteristics of a parachute-supported reentry capsule that had a compliable metal structure as a load-alleviating device. A 1/6-scale dynamic model having compliable aluminum-alloy legs designed to give a low onset rate of acceleration on impact was tested at flight-path angles of 90 degrees (vertical) and 35 degrees, at a vertical velocity of 30 ft/sec (full scale), and at contact attitudes of 0 degrees and +/-30 degrees. Landings were made on concrete, sand, and water.

[Division] Structures↗
NASA NTRS1999

DS-2 Mars Microprobe Battery

In January of 1999 the NM DS-2 Mars microprobe will be launched to impact on Mars in December. The technical objectives of the missions are to demonstrate: key technologies, a passive atmospheric entry, highly integrated microelectronics which can withstand both low temperatures and high decelerations, and the capability to conduct in-situ, surface and subsurface science data acquisition. The scientific objectives are to determine if ice is present below the Martian surface, measure the local atmospheric pressure, characterize the thermal properties of the martian subsurface soil, and to estimate the vertical temperature gradient of the Martian soil. The battery requirements are 2-4 cell batteries, with voltage of 6-14 volts, capacity of 550 mAh at 80C, and 2Ah at 25C, shelf life of 2.5 years, an operating temperature of 60C and below, and the ability to withstand shock impact of 80,000 g's. The technical challenges and the approach is reviewed. The Li-SOCL2 system is reviewed, and graphs showing the current and voltage is displayed, along with the voltage over discharge time. The problems encountered during the testing were: (1) impact sensitivity, (2) cracking of the seals, and (3) delay in voltage. A new design resulted in no problems in the impact testing phase. The corrective actions for the seal problems involved: (1) pre weld fill tube, (2) an improved heat sink during case to cover weld and (3) change the seal dimensions to reduce stress. To correct the voltage delay problem the solutions involved: (1) drying the electrodes to reduce contamination by water, (2) assemblage of the cells within a week of electrode manufacture, (3) ensure electrolyte purity, and (4) provide second depassivation pulse after landing. The conclusions on further testing were that the battery can: (1) withstand anticipated shock of up to 80,000 g, (2) meet the discharge profile post shock at Mars temperatures, (3) meet the required self discharge rate and (4) meet environmental requirements.

Frank, H.↗
NASA NTRSDate not supplied

The ESA Hera Mission: Detailed Investigation of the NASA Dart Impact Outcome and Characterization of the Binary Asteroid Didymos

The Hera mission is in development in the Space Safety Program of the European Space Agency (ESA) in collaboration with JAXA for launch in October 2024. It will rendezvous with the binary asteroid (65803) Didymos in early 2027 and over the following 6 months will investigate the properties of Didymos and its small moon Dirmorphos, including the effects of the successful impact of the NASA DART probe. DART was launched on 24 November 2021 at 06:21 UTC and successfully impacted at about 6.1 km/s on the 160 meter-size Dimorphos on 26 September 2022 at 23:14 UTC. Two weeks before impact, it deployed the Light Italian Cubesat for Imaging of Asteroids (LICIACube) that provided images during the few minutes following the impact. A campaign of observations from Earth and space provided distant images of the event, which were used to determine a reduction of 33 min in the orbital period of Dimorphos around Didymos. The Hera mission will investigate the outcome of the DART impact in detail. In particular, it will determine the effects of the impact on Dimorphos’ surface, e.g., whether it produced a crater, and if so its properties, and/or whether it led to global reshaping of Dimorphos. It will accurately measure the mass of Dimorphos, which will allow quantification of the momentum enhancement factor, which is a crucial parameter to evaluate the efficiency of the kinetic impactor technique. Hera will also determine in detail the physical, thermal and compositional properties of the asteroid, including first time measurements of the internal properties, which have a critical influence on the impact outcome. With Hera and DART together, we will have a fully documented deflection test and impact experiment that will allow us to verify our numerical impact models, to be able to extrapolate this deflection test to other asteroids and to improve our understanding of the complex geological properties and response of small asteroids. Hera consists of a mother spacecraft and two cubesats. It will perform the first rendezvous with a binary asteroid, arriving at Didymos about 4 years after DART. Hera will not only contribute significantly to the planetary defense effort by documenting entirely the outcome of the DART impact, it will also greatly advance our understanding of processes in the very low gravity regime of a small asteroidv (Dimorphos) as well as our knowledge of binary asteroids and asteroid geophysics. The mission development is progressing nominally, with the Critical Design Review having been passed in Nov. 2022. The various working groups of the Hera Science Team are working intensively to support this development and be best prepared for the surprises that Hera will offer during its visit to Didymos in 2027.

Asteroid deflection↗
NASA NTRS1982

Lacquer Reveals Impact Damage in Composites

Brittle lacquer unveils effects normally visible only by ultrasonic inspection. Laquer coating measures spread of cracking and delamination in graphite/epoxy panels subjected to cyclic compression loads after impact damage. Test specimen is coated with lacquer on side opposite surface at which projectile will be fired. Spalled area shows effect of impact without removing specimen from test fixture.

Rhodes, M. D.↗