Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GaSe”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

A comparative investigation of the effect of gas type on foam strength and flow behavior in tight carbonates

Foam generation technique has been practically applied to overcome gas mobility issue during enhanced oil recovery (EOR) processes. Incorporated with the utilized gas, the capability of foaming agent to generate persistent foam determines the flow performance under reservoir conditions. Here, in this study, we first identified the surfactants with excellent phase behavior and foaming properties and, second, evaluated their bulk foam performance with different gases, including N 2 , CO 2 , and hydrocarbon gas (CH 4 ) under high-pressure and high-temperature conditions. In bulk, the foam generated with the high-density gas, i.e., CO 2 , exhibited the greatest foamability but the lowest foam stability. With amidoamine oxide-based surfactant, CH 4 -foam was found to be more stable than N 2 -foam, while the opposite was observed for sulfobetaine-based surfactant. The most effective surfactant was later used to perform flow experiments on two tight carbonate rocks, including Minnesota Norther Cream Buff and Edwards limestone, with permeabilities of ~0.8 and 16 mD, respectively. The core-flooding experiments showed that the optimum quality of CO 2 -foam was lower than that of N 2 - and CH 4 -foams. For a given flow rate and fixed foam quality, the steady-state strength followed the descending order of CH 4 -, N 2 -, and CO 2 -foam. However, in general, the difference in foam strength between N 2 - and CH 4 -foams was insignificant when the total flow rate was varied. We also found that the variation in rock permeability had a greater effect on the strength of the CO 2 -foam compared to those generated with N 2 and CH 4 . In the presence of oil, the shear-thinning behavior of all foams was found more prominent. The increase in oil saturation had a more adverse effect on the strength of N 2 - and CH 4 -foams, particularly in the higher permeability rock. The results indicated that the foam strength, which is key in the effectiveness of foam EOR applications, is greatly influenced by several factors such as gas density, gas solubility in water, the presence of oil, and rock permeability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Polymeric ionic liquids containing copper(I) and copper(II) ions as gas chromatographic stationary phases for olefin separations

Copper(I) ions (Cu + ) are used in olefin separations due to their olefin complexing ability and low cost, but their instability in the presence of water and gases limits their widespread use. Ionic liquids (ILs) have emerged as stabilizers of Cu + ions and prevent their degradation, providing high olefin separation efficiency. There is limited understanding into the role that polymeric ionic liquids (PILs), which possess similar structural characteristics to ILs, have on Cu + ion-olefin interactions. Moreover, copper ions with diverse oxidation states, including Cu + and Cu 2+ ions, have been rarely employed for olefin separations. In this study, gas chromatography (GC) is used to investigate the interaction strength of olefins to stationary phases composed of the 1-hexyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide ([C 6 MIM + ][NTf 2 – ]) IL and the poly(1-hexyl-3-vinylimidazolium [NTf 2 – ]) (poly([C 6 VIM + ][NTf 2 – ])) PIL containing monovalent and divalent copper salts (i.e., [Cu + ][NTf 2 – ] and [Cu 2+ ]2[NTf 2 – ]). The chromatographic retention of alkenes, alkynes, dienes, and aromatic compounds was examined. Incorporation of the [Cu 2+ ]2[NTf 2 – ] salt into a stationary phase comprised of poly(dimethylsiloxane) resulted in strong retention of olefins, while its addition to the [C 6 MIM + ][NTf 2 – ] IL and poly([C 6 VIM + ][NTf 2 – ]) PIL allowed for the interaction strength to be modulated. Olefins exhibited greater affinities toward IL and PIL stationary phases containing the [Cu 2+ ]2[NTf 2 – ] salt compared to those with the [Cu + ][NTf 2 – ] salt. Elimination of water from both copper salts was observed to be an important factor in promoting olefin interactions, as evidenced by increased olefin retention upon exposure of the stationary phases to high temperatures. Furthermore, to evaluate the long-term thermal stability of the stationary phase, chromatographic retention of probes was measured on the [Cu 2+ ]2[NTf 2 – ]/[C 6 MIM + ][NTf 2 – ] IL stationary phase after its exposure to helium at a temperature of 110°C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Geocatalytically generated methane from low-maturity coal and shale source rocks at low temperatures (80–120 °C) over 52 months

Geocatalytic methanogenesis has been proposed to contribute to methane generation from low-maturity coal and shale source rocks. This study contributes further evidence for geocatalytic methanogenesis from low-maturity source rocks based on long-term experiments lasting up to 52 months. Samples from the Upper Devonian New Albany Shale (R o 0.54 %) and Springfield Coal No. 2 (Pennsylvanian; R o 0.54 %) were heated in glass tubes at 80, 100, and 120 °C for 52 months. Sample aliquots from the Upper Cretaceous Second White Specks Formation (R o 0.42 %) were heated in gold tubes at 80 and 100 °C for 42 months at elevated hydrostatic pressures of 100 to 300 MPa. The product gases — methane (CH 4 ) and carbon dioxide (CO 2 ) — were collected and quantified, and gas yields were corrected for leakage from imperfectly closed pores in samples during heating. The results show that longer heating produced more CH 4 . The average CH 4 yields from New Albany Shale and Springfield Coal No. 2 are 0.47 and 3.0 μmol CH 4 per gram of total organic carbon (TOC) over 52 months of heating. Elevated hydrostatic pressure caused lower CH 4 yields from the Second White Specks Formation (3.82 to 1.20 μmol g –1 TOC), suggesting that pressure can retard methanogenesis. Maceral type critically controls the methanogenesis potential of low-maturity coal and shale source rocks. Finally, results of this study provide important insights to the origin of natural gas in low-maturity sedimentary basins.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Component Identification of Solid Biomass Fuels Using Reflected Light Microscopy: Interlaboratory Study 2

As nations transition toward sustainable energy systems, biomass has become a vital component of global energy portfolios. Derived from organic materials such as wood, agricultural residues, forestry byproducts, and organic waste, biomass is a renewable energy source with significant environmental and economic benefits. Responsible biomass energy production can improve waste management, reduce emissions of greenhouse gases, and mitigate environmental pollution. However, as the diversity of biomass-derived fuels increases, robust quality assessment methods are essential to ensure their efficiency, safety, and minimal environmental impact. Reflected light microscopy (RLM) is one such technique with the potential to complement conventional physico-chemical analyses by enabling a rapid identification of material constituents and impurities. To refine this methodology and evaluate the reproducibility of solid biomass component identification using RLM, an interlaboratory study (ILS) was conducted. The study involved the recognition of 58 components across 45 photomicrographs, with the participation of 65 scientists and students from 25 countries. The participants faced high difficulty identifying some of the marked components, and as a result, the percentage of correct answers ranged from 19.0 % to 98.3 %, with an average correct identification rate of 62.7 %. The most challenging aspects of the identification process included distinguishing between woody and non-woody (agro) biomass, accurately identifying petroleum-derived materials, and differentiating agro biomass from inorganic matter. The results suggest that while RLM is an important tool for characterizing solid biomass, further development of methodology guidelines and training are necessary to enhance its effectiveness. Future research should prioritize preparing detailed, image-rich, microscopic morphological descriptions of biomass fuel components, which could improve the accuracy and reliability of using RLM in biomass fuel characterization.

09 BIOMASS FUELS↗
DOE OSTI2021

Temporally and spatially resolved X-ray densitometry in a shock tube

Gas densities were measured by x-ray absorption spectroscopy to examine spatial inhomogeneity in density behind incident and reflected shock waves in a miniature (12.7 mm bore) high repetition rate shock tube. Shock waves were generated in argon. The pressure and temperature behind the incident shock were P 2 ~ 1.72 bar and T 2 ~ 800 K, while those behind the reflected shock were P 5 ~ 6.5 bar and T 5 ~ 1480 K. Time-resolved line-of-sight transmission measurements using x-rays at 9 keV photon energy were made along various axial and transverse locations covering the entire shock tube cross section. The x-ray transmission at each location was converted to pathlength-integrated densities, which in some conditions could be further converted to pathlength-averaged densities. The measured gas densities were compared with those calculated by the normal shock wave relations, and good agreement was found in the preshock and immediately behind the incident shock regions. Similar agreement was found for reflected shock conditions very near the endwall. However, increasingly large differences between the measured and calculated gas densities were found as distance from the endwall increased. Furthermore, reconstruction by Abel inversion allowed time and radially resolved densities to be obtained from the transverse measurements. While the profiles measured in this experiment are of insufficient signal-to noise level and resolution to definitively assign boundary layer thicknesses, future improvements may be able to do this. The radially resolved densities reveal growing sidewall thermal boundary layers in gases behind the reflected shock. These reconstructions were compared with a model of the thermal boundary layer and are consistent with values of the thermal boundary layer thickness being between 0.25 mm and 1 mm at 0.7 ms after shock reflection.

42 ENGINEERING↗
DOE OSTI2020

Combustion of metal powder with dinitrogen tetroxide

In this work, we present analysis of a novel reactive material system that employs dinitrogen tetroxide (N 2 O 4 ) as a liquid oxidizer with metal powder fuels. The oxidizer was added to micron scale aluminum and zirconium powders by a remote injection system. When ignited with a high voltage spark, the mixtures were observed to possess reactivity comparable to nanocomposite reactive materials, with open-tube flame expansion velocities from 500 to 1400 m/s depending on fuel/oxidizer ratio and tube diameter. Temperatures were observed to range from 3000 to 3500 K as measured with gray body fits to 16-channel time-resolved pyrometer and time-integrated spectrometer data. These values were significantly below calculated adiabatic flame temperatures, which we attribute to local deviations from stoichiometry and kinetic/energetic limitations similar to those observed in studies of particles burning in high pressures gaseous oxidizers. Al/N 2 O 4 reactivity was found to be most likely limited by the vaporization of the metal from the particle surface and Zr/N 2 O 4 was limited by slower burning and complex interactions involving the solubility of nitrogen and oxygen in the molten Zr. We also discuss the potential for these materials to be used to create an “on/off” reactive material, since N2O4 can be added remotely and driven to evaporate via vacuum or purge of inert gases to return it to a safe condition.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Finite-rate entrainment effects on nitrogen oxide (NO x ) emissions in staged combustors

Axially staged combustors offer the potential for achieving low NO x emissions from gas turbines at the elevated temperatures required to achieve at least 65% combined cycle efficiencies. While there is evidence that premixing between the main burner products and secondary stream reduces NO x , it is important to characterize the specific requirements needed to achieve low emissions at gas turbine conditions. This study examines the sensitivity of NO x to finite-rate, large-scale entrainment of the main and secondary streams under the simplifying assumption of infinitely-fast small-scale mixing. Essentially, this allows us to isolate the effects of limited large-scale entrainment rates by using a homogeneous/uniform condition for the entrained and reacting gases. We use a reduced-order reactor network model to examine a generic staged-combustor whose inputs are physical time scales that embody the finite-rate entrainment characteristics. With simulations conducted over a large parameter space at typical operating conditions (25 atm, 650 K air), the results show that, even when small-scale mixing is infinitely fast and the reaction zone is uniform, entrainment significantly affects NO x emissions due to its influence on the equivalence ratio — and thus the temperature and time — at which the entrained mixture ignites. Fuel-air staging is shown to be vital to NO x reduction in most practical cases where entrainment times exceed roughly 1 ms and the secondary stream finishes entraining before the main burner products. A constrained NO x minimization indicates that using the leanest possible main burner and re-routing as much air as possible to the secondary stage is key to low NO x with finite-rate entrainment; for example, less than 10 ppm NO x can be achieved if the secondary stage contains 20% of the total mass flow.

03 NATURAL GAS↗
DOE OSTI2023

Experimental measurement of the rapid mixing of fuel and air in a multi-element diffusion (Hencken) burner

Flat flame burners are valuable tools for studying complex combustion phenomena like particle synthesis due to the well-controlled and well-behaved initial and boundary conditions. In this study, the methane/air flame temperature and tracer density profiles of a multi-element diffusion burner equipped with a central tube were characterized using krypton (Kr) x-ray fluorescence at the Advanced Photon Source at Argonne National Laboratory. The experiments were performed using a fuel-to-oxygen equivalence ratio of 0.8 and 3.3% Kr by volume was added to the reactant gases. One- and two-dimensional scans of non-combusting (i.e., cold flow) and combusting conditions, both with and without flow through the central tube were performed. Spatially-resolved Kr number density profiles were obtained at different planar locations and heights above the surface of the burner. The results show rapid mixing occurred near the exit-plane of the burner and increased spatial uniformity was achieved from 0.1 mm to 0.5 mm above the surface of the burner. Further, the data also showed the impact of the central tube flow on the main methane/air flame, including evidence of the central tube flow mixing with the main flow. Flame temperatures were calculated from the fluorescence measurements at various heights above the burner surface and were in good agreement with model predictions for a burner stabilized flame. These high-fidelity measurements provide accurate baseline data that are particularly valuable for understanding the effects of fuel and air mixing on downstream phenomena, such as the formation of condensed-phase products.

42 ENGINEERING↗
DOE OSTI2024

An experimental, theoretical, and kinetic modeling study of post-flame oxidation of ammonia

The post -flame oxidation rate of ammonia was investigated in a novel atmospheric pressure flow reactor at temperatures of 1280 ± 16 K and as a function of residence time and mixture composition (1-10% O 2 , dry and moist). The experimental results, as well as selected data from literature, were analyzed using an updated detailed chemical kinetic model. The medium temperature, very lean conditions enhance the importance of reactions of the nitroxyl (HNO) intermediate. High-level theory was used to calculate the rate constant for HNO + NH 2 , indicating that this step is significantly faster than values used in literature. Furthermore, a trajectory based approach was used to determine collision efficiencies for selected bath gases for HNO + M. The experimental results show that the NH 3 oxidation rate increases with temperature and O 2 concentration, while the presence of water vapor slightly inhibits reaction. Formation of NO and N 2 O was strongly promoted at higher levels of O 2 . Modeling results agreed well with the measurements, except at the lowest level of O 2 . The predicted oxidation rate of NH 3 was shown to result from a delicate balance between chain branching and terminating steps involving NH 2 , H 2 NO, and HNO. Recent theoretical work on reactions of these species by Klippenstein and coworkers and Stagni et al. was instrumental in improving modeling predictions. After initiation, NO reached a pseudo -steady-state level, where the pathways to NO were largely balanced by the NH 2 + NO reaction. Nitric oxide was partly oxidized to NO 2 , with the NH 2 + NO 2 reaction responsible for most of the N 2 O formation. Novelty and significance statement: This study provides the first detailed kinetic analysis of the lean postflame oxidation of ammonia, based on time -resolved flow reactor data in a novel reactor. In addition to the post -flame oxidation rate of ammonia, data for formation of NO and N 2 O were compared with modeling predictions. The medium temperature, very lean conditions enhance the importance of reactions of the HNO and H 2 NO intermediates. Inclusion in the model of results from recent high-level theoretical work, including present calculations for HNO + NH 2 and HNO + M, was crucial for capturing the observed behavior. It is argued that the post -initiation steady-state NH 3 oxidation rates constitute important data for model validation, along with ignition delays and laminar flame speeds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

In-situ two-dimensional temperature measurements using x-ray fluorescence spectroscopy in laminar flames with high silica particle concentrations

X-ray fluorescence spectroscopy (XRF) was used to measure temperatures and study mixing, for the first time in silica particle synthesis flames. Hexamethyldisiloxane (HMDSO) and trimethylsilanol (TMSO) were the particle precursors. A multi-element diffusion burner was used to produce a flat methane flame, and the precursors, dilute in inert gas, were injected via a central jet. Krypton was the fluorescent medium at 3.2 % concentration by volume. Scans with Kr in the central flow and not in the main flow were made to assess the mixing effects between the central and main gas flows. When HMDSO or TMSO were added, a secondary diffusion flame formed between the jet and the main methane flame. The results revealed a dramatic change in the centerline temperature profile of the jet gases when HMDSO or TMSO were added. The main methane flame stoichiometry also affected the temperature profiles. The results show HMDSO and TMSO reactions are initiated in a lowtemperature and low-oxygen concentration region of the jet where thermal decomposition is not expected to be significant. Reaction of the particle precursors is therefore attributed to radical transport from the main methane flame. In the current work, particle number densities of up to 270 g/m 3 locally are estimated. Thus, the study also demonstrates the capability of the XRF technique for high spatial fidelity measurements in flames with high concentrations of condensed-phase particles, leveraging the attribute that the XRF signal is generally not impacted by condensed-phase interferences. In conclusion, the observations and data obtained in this study inform likely reaction pathways for this important class of siloxane compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Experimental and modeling study of the autoignition behavior of a saturated heterocycle: Pyrrolidine

Experiments are conducted in both rapid compression machine (RCM) and shock tube (ST) to better quantify autoignition behavior (e.g., ignition delay, heat release) and understand heteroatomic effects in heterocyclic compounds, which are important reference components for the combustion of biomass-derived liquid fuels. These tests focus on the nitrogen-containing, five-membered saturated ring, pyrrolidine, at diluted conditions covering pressures of 20 and 50 bar, temperatures of 720–1450 K and a range of stoichiometries (ϕ = 0.5–2). A chemical kinetic model is developed and coupled to an existing combustion kinetics framework describing key nitrogen containing intermediates (e.g. pyrrole, ammonia and NOx). H-abstraction reactions by OH, H, CH 3 and HO 2 , are determined using ab-initio transition state theory methods, while analogies to cyclopentane are adopted for many other reactions, such as ring-opening. Here, the autoignition measurements reveal the lack of negative temperature coefficient (NTC) behavior and low-temperature chemistry for pyrrolidine, as opposed to its saturated hydrocarbon analogue, cyclopentane. Interestingly, at the lowest temperatures (T < 750 K), the reactivity of cyclopentane is greater than pyrrolidine, while at higher temperatures, pyrrolidine becomes more reactive. Agreement between the experimental measurements and the model is good, and it is found that H-abstraction reactions by HO 2 and ensuing chemistry play key roles in controlling the reactivity of this cyclic amine. Most of the fluxes, i.e., >70 %, are predicted to move through 1- or 2-pyrroline (C 4 H 7 N) and then the cyclic C 4 H 6 N radical, at both lower and higher temperatures, to form either CH 2 CHCHCHNH via ring-opening or pyrrole via β-scission. It appears that the ring opens more easily at lower temperature whereas the C–H β-scission dominates at higher temperature and lower pressure, such that the reaction of the fuel radical intermediate carrying an unpaired electron on the nitrogen atom with HO 2 is the next most notable in promoting oxidation. When comparing pyrrolidine and cyclopentane, which exhibits distinct pathways in different temperature regimes, the pyrrolidine pathways and sensitivity analysis align more closely to the high temperature case of cyclopentane where the important role of HO 2 radicals is seen to provide chain branching through HO 2 reaction with the fuel, accompanied by H 2 O 2 formation and decomposition to OH. The formation of 5-membered diene rings and ring opening reactions are also found to be highly relevant. Of particular note, it is found that there is little influence of small molecule nitrogen-chemistry, e.g., NH 2 , HCN, NO/NO 2 on the reactivity of the pyrrolidine mixtures investigated here where no recirculated combustion gases are included.

Autoignition↗
DOE OSTI2025

Experimental and fuel-surrogates modeling study of the high-pressure pyrolysis of specialty cetane number fuels: implications for fall-off in ethylene unimolecular dissociation

Single pulse shock tube experiments were conducted at 50 atm nominal pressure and 4 ms nominal reaction time over a temperature range of 900–1800 K, to study the pyrolysis speciation of a multi-component jet fuel, F-24, and six cetane number (CN) specialty fuels - CN30, CN35, CN40, CN45, CN50, and CN55. Gas chromatography (GC) was used to qualitatively and quantitatively analyze the post shock gases. The relationship between the formation of key pyrolysis species and the chemically controlled combustion propensity as reflected by the cetane number of each fuel was examined. A surrogate-based mechanism from the CRECK Modelling Group and chemical-functional group based optimized surrogates (CFGO) were used to simulate the pyrolysis speciation results. The model was able to capture the chemistry of most species except two important pyrolysis intermediates – ethylene and acetylene. Chemical kinetic analyses were performed to identify the important reactions which affect the chemistry of these species; however, the rate parameters of critical reactions were found to be unsuitable for simulating the present high-pressure studies. Here, to address this unsuitability, a theory-based fall-off analysis for three reactions representing the decomposition of ethylene and subsequent formation of acetylene was performed, and these are included in an updated version of the CRECK mechanism. This update resolves discrepancies between the experimental results and simulations for ethylene and acetylene. Reaction flux analyses using the updated surrogate model were also performed to identify the important reaction pathways responsible for the formation of crucial species and to provide an analysis of the chemistry of complex multi-component fuel systems. The fundamental reactions responsible for driving pyrolysis chemistry were greatly influenced by the chemical functional groups present in these fuels. In addition to updating the rate parameters of specific reactions to improve modeling, this study also emphasizes the effectiveness of the fuel-surrogate approach, where surrogates representing the chemical functional group composition of the parent fuel serve as a valuable tool for predicting the combustion chemistry of novel fuels.

Chemical Kinetics↗
DOE OSTI2025

An isotopic labeling investigation into the influence of the nitro group on LLM-105 thermal decomposition

Here, this work presents the first application of isotopically labeled LLM-105 (2,6-diamino-3,5-dinitropyrazine-1-oxide) to investigate thermal decomposition pathways. Specially synthesized LLM-105 isotopologues were utilized to isolate the influence of labeled 15 NO 2 nitro groups on the formation of lightgas products. Simultaneous differential scanning calorimetry, thermo-gravimetric, and mass spectrometry measurements were employed to track the evolution of product gases, enabling the direct comparison of isotopically shifted species with unlabeled LLM-105. Key findings show that C 2 N 2 production is mainly dependent on nitrogen sources from either the amine groups or the pyrazine ring (i.e., not the nitro groups). The formation of NO, N 2 , and N 2 O all involves the nitro groups to some extent. NO (nitric oxide) was found to be the predominant gas species directly formed from the nitro group of LLM-105. In contrast, mixed nitrogen isotopologues of N 2 and N 2 O (i.e., 14 N 15 N and 15 NNO) formed more readily in comparison to their pure counterparts (i.e., 15 N 2 and 15 N 2 O). This indicates the amine and/or pyrazine groups of LLM-105, in addition to the nitro group, are involved in the decomposition pathways forming N 2 and N 2 O. In addition, our investigation led to the discovery of two previously unreported decomposition products (CHO and HNCO), which were confirmed through hydrogen labelling utilizing deuterium isotopes. These results provide detailed speciation trends of gaseous products during LLM-105 decomposition, offering new insights into reaction pathways. Experimental data reported here will support the development of a detailed chemical kinetics model for LLM-105, essential for the safe handling of high explosives.

Chemistry - Chemical explosives↗
DOE OSTI2025

Bacterial microcompartment architectures as biomaterials for conversion of gaseous substrates

Bacterial microcompartments (BMCs) are protein shells encapsulating multiple enzymes of a metabolic pathway. Interpretations of early experiments on carboxysomes led to the narrative that transport of small gases (CO 2 , O 2 ) across the shell membrane is restricted. Since then, this notion has been largely contradicted by studies of engineered shells, although these shell constructs lack important proteins present in the native BMCs, altering the synthetic shells’ topology, surface and mechanical properties. Here, we discuss here an updated model of gas permeability that informs the design of engineered shells for catalysis on gas substrates and outline how nonshell suprastructures of BMC shell proteins could be used in formulating sustainable biomaterials for hydrogen generation via methane pyrolysis and for other greenhouse gas mitigations.

Bacterial microcompartment↗
DOE OSTI2022

Comprehensive insights into competitive oxidation/sulfidation reactions on binary ferritic alloys at high temperatures

Interpreting high-temperature corrosion induced by mixed-gas atmospheres is challenging due to the different contributions of oxidizing gases. In this work, a comprehensive study on the combined oxidation/sulfidation using label molecules is presented. Fe-Cr model alloys with 2 wt% and 9 wt% Cr were isothermally exposed using a volumetric mixture of 0.5%S 16 O 2 /27%H 2 18 O and 0.5%S 16 O 2 /7%H 2 18 O at 650 °C for 5 h and then characterized by secondary ion mass spectroscopy (SIMS). Additionally, the reactions were followed in-situ utilizing energy dispersive X-ray diffraction. The study showed that both S 16 O 2 and H 2 18 O contribute to the oxidation of the alloys but to different extents depending on the Cr-content.

36 MATERIALS SCIENCE↗
DOE OSTI2020

HTR solver: An open-source exascale-oriented task-based multi-GPU high-order code for hypersonic aerothermodynamics

In this study, the open-source Hypersonics Task-based Research (HTR) solver for hypersonic aerothermodynamics is described. The physical formulation of the code includes thermochemical effects induced by high temperatures (vibrational excitation and chemical dissociation). The HTR solver uses high-order TENO-based spatial discretization on structured grids and efficient time integrators for stiff systems, is highly scalable in GPU-based supercomputers as a result of its implementation in the Regent/Legion stack, and is designed for direct numerical simulations of canonical hypersonic flows at high Reynolds numbers. Additionally, the performance of the HTR solver is tested with benchmark cases including inviscid vortex advection, low- and high-speed laminar boundary layers, inviscid one-dimensional compressible flows in shock tubes, supersonic turbulent channel flows, and hypersonic transitional boundary layers of both calorically perfect gases and dissociating air.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

SPACE: 3D parallel solvers for Vlasov-Maxwell and Vlasov-Poisson equations for relativistic plasmas with atomic transformations

A parallel, relativistic, three-dimensional particle-in-cell code SPACE has been developed for the simulation of electromagnetic fields, relativistic particle beams, and plasmas. In addition to the standard second-order Particle-in-Cell (PIC) algorithm, SPACE includes efficient novel algorithms to resolve atomic physics processes such as multi-level ionization of plasma atoms, recombination, and electron attachment to dopants in dense neutral gases. SPACE also contains a highly adaptive particle-based method, called Adaptive Particle-in-Cloud (AP-Cloud), for solving the Vlasov-Poisson problems. It eliminates the traditional Cartesian mesh of PIC and replaces it with an adaptive octree data structure. The code's algorithms, structure, capabilities, parallelization strategy, and performance have been discussed. Additionally, typical examples of SPACE applications to accelerator science and engineering problems are described.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Adaptations for gas exchange enabled the elongation of lepidopteran proboscises

The extensive biodiversification of butterflies and moths (Lepidoptera) is partly attributed to their unique mouthparts (proboscis [Pr]) that can span in length from less than 1 mm to over 280mm in Darwin's sphinx moths. Lepi-doptera, similar to other insects, are believed to inhale and exhale respiratory gases only through valve-like spi-racles on their thorax and abdomen, making gas exchange through the narrow tracheae (Tr) challenging for the elongated Pr. How Lepidoptera overcome distance effects for gas transport to the Pr is an open question that is important to understanding how the Pr elongated over evolutionary time. Here, we show with scanning electron microscopy and X-ray imaging that distance effects on gas exchange are overcome by previously unreported micropores on the Pr surface and by superhydrophobic Tr that prevent water loss and entry. We find that the density of micropores decreases monotonically along the Pr length with the maxima proportional to the Pr length and that micropore diameters produce a Knudsen number at the boundary between the slip and transition flow regimes. By numerical estimation, we further show that the respiratory gas exchange for the Pr predominantly occurs via diffusion through the micropores. In conclusion, these adaptations are key innovations vital to Pr elongation, which likely facilitated lepidopteran biodiversification and the radiation of angiosperms by coevolutionary processes.

59 BASIC BIOLOGICAL SCIENCES↗