Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GRINDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Two-Dimensional Air-Flow Tests of the Effect of ITA Flowliner Slot Modification by Grinding/Polishing on Edge Tone Generation Potential

Hersh Walker Acoustics (HWA) has performed a series of wind tunnel tests to support crack-repair studies for ITA flowliner vent slots. The overall goal of these tests is to determine if slot shape details have a significant influence on the propensity of the flowliner to produce aero-acoustic oscillations that could increase unsteady stresses on the flowliner walls. The test series, conducted using a full-scale two-dimensional model of a six-slot segment of the 38 slot liner, was intended to investigate the effects of altering slot shape by grinding away cracked portions.

Sutliff, Daniel L.↗

Face Gear Drive With Helical Involute Pinion: Geometry, Generation by a Shaper and a Worm, Avoidance of Singularities and Stress Analysis

A new type of face-gear drive with intersected axes of rotation formed by a helical involute pinion and conjugated face-gear has been investigated. Generation of face-gears by a shaper free of undercutting and pointing has been investigated. A new method of grinding or cutting of face-gears by a worm of special shape has been developed. A computerized design procedure has been developed to avoid undercutting and pointing by a shaper or by a generating worm. Also, a method to determine the limitations of the helix angle magnitude has been developed. The method provides a localization of the bearing contact to reduce the shift of bearing contact caused by misalignment. The analytical method provides a simulation of the meshing and contact of misaligned gear drives. An automatic mesh generation method has been developed and used to conduct a 3D contact stress analysis of several teeth. The theory developed is illustrated with several examples.

Litvin, Faydor L.↗

Mineralogy at Gusev Crater from the Mossbauer spectrometer on the Spirit Rover

Mossbauer spectra measured on Mars by the Spirit rover during the primary mission are characterized by two ferrous iron doublets (olivine and probably pyroxene) and a ferric iron doublet (tentatively associated to nanophase ferric iron oxide). Two sextets resulting from nonstoichiometric magnetite are also present, except for a coating on the rock Mazatzal, where a hematite-like sextet is present. Greater proportions of ferric-bearing phases are associated with undisturbed soils and rock surfaces as compared to fresh rock surfaces exposed by grinding. The ubiquitous presence of olivine in soil suggests that physical rather than chemical weathering processes currently dominate at Gusev crater.

Minerals↗

Pancam multispectral imaging results from the Spirit Rover at Gusev Crater

Panoramic Camera images at Gusev crater reveal a rock-strewn surface interspersed with high- to moderate-albedo fine-grained deposits occurring in part as drifts or in small circular swales or hollows. Optically thick coatings of fine-grained ferric iron-rich dust dominate most bright soil and rock surfaces. Spectra of some darker rock surfaces and rock regions exposed by brushing or grinding show near-infrared spectral signatures consistent with the presence of mafic silicates such as pyroxene or olivine. Atmospheric observations show a steady decline in dust opacity during the mission, and astronomical observations captured solar transits by the martian moons, Phobos and Deimos, as well as a view of Earth from the martian surface.

Mars↗

Results and Implications of Mineralogical Models for Chemical Sediments at Meridiani Planum

The Mars Exploration Rover (MER) "Opportunity" has explored chemically-enriched sedimentary outcrops at Meridiani Planum, Mars. In its first year, three different crater sites - Eagle, Fram and Endurance - have been explored. Nineteen high-interest outcrop rocks were investigated by first grinding a hole to reach the interior (using the Rock Abrasion Tool, RAT), and then conducting APXS (alpha particle x-ray spectrometry) analysis, MB (M ssbauer) analysis, and close up imaging (MI, microscopic imager). Sixteen elements and four Fe-bearing minerals were assayed to good accuracy in each sample, producing 380 compositional data points. The Miniature Thermal Emission Spectrometer (Mini- TES) obtained spectra on outcrop materials which provide direct indication of several mineral classes. Preliminary reports on Eagle crater and three RAT samples have been published. Chemical trends and a derived mineralogical model for all RAT d outcrop samples to date has been developed.

Clark, B. C.↗

Gear Durability Shown To Be Improved by Superfinishing

Gears, bearings, and similar mechanical elements transmit loads through contacting surfaces. At the NASA Glenn Research Center at Lewis Field, we postulated that the fatigue lives of gears could be improved by providing smoother tooth surfaces. A superfinishing process was applied to a set of conventionally ground, aerospace-quality gears. This process produced a highly polished, mirrorlike surface as shown in the preceding photograph. The surface fatigue lives of both superfinished and conventionally ground gears were measured by experiments. The superfinished gears survived about four times longer than the conventionally ground gears. These superfinished gears were produced from conventionally ground, aerospace-quality gears whose geometry had been inspected. The gears were superfinished by placing them in a vibrating bath consisting of water, detergent, abrasive powder, and small pieces of zinc. Upon removal from the bath, the surfaces were highly polished, as depicted in the preceding photograph. The gears were again inspected, and dimensional measurements made before and after the superfinishing operation were compared. Superfinishing removed the peaks of the grinding marks and left a much smoother surface. Profile and spacing checks proved that the overall gear tooth shape was not affected in any harmful way. Superfinishing uniformly removed approximately 2.5 microns from each surface.

Krautz, Timothy L.↗

Comparison Made of Operating Characteristics of Spiral Bevel Gears Manufactured Using Different Methods

Spiral bevel gears are important components on all current rotorcraft drive systems. These components are required to operate at high speeds, high loads, and for an extremely large number of load cycles. In this application, spiral bevel gears are used to redirect the shaft from the horizontal gas turbine engine to the vertical rotor. Because of the high expense of manufacturing these gears, methods that can achieve the same level of performance at reduced cost are highly desirable to aerospace gear manufacturers. Gears manufactured for aerospace applications use high-quality materials and are manufactured to tight tolerances. Special manufacturing machine tools and computer numerically controlled coordinate measurement systems have enabled rotorcraft drive system manufacturers to produce extremely high-quality gears during their normal production. Because of low production rates for rotorcraft, these gears are manufactured in small batches, and thus are unable to benefit from the economics of high production numbers as in other industries. In this investigation, two different manufacturing methods, face-milled and face-hobbed, were used to fabricate spiral bevel gears. For face-milled spiral bevel gears, grinding of the contacting surfaces is the final manufacturing step. At least two different specialty machines are needed to generate the teeth for face-milled spiral bevel gears. For face-hobbed gears, hard cutting is the final manufacturing process. The same machine is used to rough cut and finish cut the gears. This study compared the operational behavior of face-milled spiral bevel gears with that of face-hobbed spiral bevel gears. Test hardware was manufactured to fit within NASA Glenn Research Center's Spiral Bevel Test Facility and to aerospace quality standards. Tests were conducted for stress, vibration, and noise. A comparison of the results attained indicated that the face-hobbed gears had a lower alternating stress level with a more even distribution of loading across the teeth, and slightly reduced levels of vibration and noise. Results of this study show that the face-hobbed method is a viable and lower-cost alternative for producing aerospace-quality spiral-bevel gears.

Handschuh, Robert F.↗

High-Temperature Oxidation-Resistant and Low Coefficient of Thermal Expansion NiAl-Base Bond Coat Developed for a Turbine Blade Application

Many critical gas turbine engine components are currently made from Ni-base superalloys that are coated with a thermal barrier coating (TBC). The TBC consists of a ZrO2-based top coat and a bond coat that is used to enhance the bonding between the superalloy substrate and the top coat. MCrAlY alloys (CoCrAlY and NiCrAlY) are currently used as bond coats and are chosen for their very good oxidation resistance. TBC life is frequently limited by the oxidation resistance of the bond coat, along with a thermal expansion mismatch between the metallic bond coat and the ceramic top coat. The aim of this investigation at the NASA Glenn Research Center was to develop a new longer life, higher temperature bond coat by improving both the oxidation resistance and the thermal expansion characteristics of the bond coat. Nickel aluminide (NiAl) has excellent high-temperature oxidation resistance and can sustain a protective Al2O3 scale to longer times and higher temperatures in comparison to MCrAlY alloys. Cryomilling of NiAl results in aluminum nitride (AlN) formation that reduces the coefficient of thermal expansion (CTE) of the alloy and enhances creep strength. Thus, additions of cryomilled NiAl-AlN to CoCrAlY were examined as a potential bond coat. In this work, the composite alloy was investigated as a stand-alone substrate to demonstrate its feasibility prior to actual use as a coating. About 85 percent of prealloyed NiAl and 15 percent of standard commercial CoCrAlY alloys were mixed and cryomilled in an attritor with stainless steel balls used as grinding media. The milling was carried out in the presence of liquid nitrogen. The milled powder was consolidated by hot extrusion or by hot isostatic pressing. From the consolidated material, oxidation coupons, four-point bend, CTE, and tensile specimens were machined. The CTE measurements were made between room temperature and 1000 C in an argon atmosphere. It is shown that the CTE of the NiAl-AlN-CoCrAlY composite bond coat is lower than that of the commercially used coating alloy 16-6. To examine the potential of NiAl-AlN-CoCrAlY as a bond coat, we subjected two samples to cyclic furnace testing. The furnace cycle consisted of 45 min at 1163 C (2125 F ) followed by 15 min of cooling out of the furnace. The current NASA baseline TBC is a NiCrAlY bond coat below the 7YSZ top coat. The average TBC life for this baseline coating on Ren N5 is 188 plus or minus 19 cycles. NiAl-AlN-CoCrAlY specimens coated with the same 7YSZ top coat were still intact even after 1000 cycles. Therefore, the NiAl-AlN-CoCrAlY as a bulk substrate material, exhibits more than 5 times the life of the current state-of-the-art material. The next step is to evaluate this material as a coating on the same superalloy substrate.

Source record↗

Slow Crack Growth and Fracture Toughness of Sapphire for the International Space Station Fluids and Combustion Facility

The fracture toughness, inert flexural strength, and slow crack growth parameters of the r- and a-planes of sapphire grown by the Heat Exchange Method were measured to qualify sapphire for structural use in the International Space Station. The fracture toughness in dry nitrogen, K(sub Ipb), was 2.31 +/- 0.12 MPa(square root of)m and 2.47 +/- 0.15 MPa(squre root of)m for the a- and r-planes, respectively. Fracture toughness measured in water via the operational procedure in ASTM C1421 was significantly lower, K(sub Ivb) = 1.95+/- 0.03 MPa(square root of)m, 1.94 +/- 0.07 and 1.77 +/- 0.13 MPa(square root of)m for the a- , m- and r-planes, respectively. The mean inert flexural strength in dry nitrogen was 1085 +/- 127 MPa for the r-plane and 1255 +/- 547 MPa for the a-plane. The power law slow crack growth exponent for testing in water was n = 21 +/- 4 for the r-plane and n (greater than or equal to) 31 for the a-plane. The power law slow crack growth coefficient was A = 2.81 x 10(exp -14) m/s x (MPa(squre root of)m)/n for the r-plane and A (approx. equals)2.06 x 10(exp -15) m/s x (MPa(square root of)m)/n for the a-plane. The r- and a-planes of sapphire are relatively susceptible to stress corrosion induced slow crack growth in water. However, failure occurs by competing modes of slow crack growth at long failure times and twinning for short failure time and inert environments. Slow crack growth testing needs to be performed at low failure stress levels and long failure times so that twinning does not affect the results. Some difficulty was encountered in measuring the slow crack growth parameters for the a-plane due to a short finish (i.e., insufficient material removal for elimination of the damage generated in the early grinding stages). A consistent preparation method that increases the Weibull modulus of sapphire test specimens and components is needed. This would impart higher component reliability, even if higher Weibull modulus is gained at the sacrifice of absolute strength of the component. The current specification frequently used for the preparation of sapphire test specimens and components (e.g., a "60/40" scratch-dig finish) is inadequate to avoid a short finish.

Salem, Jonathan A.↗

ROCK AND SOIL PHYSICAL PROPERTIES AT THE MER GUSEV CRATER AND MERIDIANI PLANUM LANDING SITES

Following the successful landings of both Mars Exploration Rover (MER) vehicles at Gusev Crater and Meridiani Planum, respectively, their Athena suite of instruments is being used to study the geologic history of these two very different landing sites on Mars that had been selected on the basis of showing different types of evidence for aqueous processes in the planet s past. Utilizing the on-board instruments as well as the rovers mobility system, a wide range of physical properties investigations is carried out as well - the subject of this abstract - that provide additional information on the geology and processes at the sites. Results of the mission in general as well as of the physical properties studies thus far greatly exceed expectations in that observations and measurements by both vehicles show a rich variety in materials and processes: the Gusev site in the vicinity of the lander is remarkably flat and generally devoid of large rocks along traverses up to the time of this writing (approx.Sol 50) and suggestive of a deflated surface with generally only thin veneers of bright dust while exhibiting evidence of a widespread occurrence of a crust from cemented fines that has been observed to fail in the form of blocky clods when disturbed by vehicle rolling action; numerous small and shallow depressions - presumably created by impacts - are observed at the site which are infilled with bright, fine-grained material that likewise appears indurated and which was studied by a trenching experiment; small ripple bedforms are scattered across the site and were characterized in terms of particle size distributions. At the Meridiani site, studies so far - up to approx.Sol 33 - have focussed on soils and the rock outcrop encountered within the approx.20 m diameter crater that the spacecraft came to rest in: from a physical properties point of view, a mantle of dark, well-sorted, apparently basaltic sand with small to moderate cohesion has been of interest - and has been studied by a trenching experiment - as well as a fine-grained unit underlying the mantle at least locally within the crater. Rock grindings were accomplished successfully at both sites at the time of this writing, suggesting different strengths of the two targets (the basaltic rock nicknamed Adirondack at Gusev and the Meridiani rock outcrop) in addition to enabling compositional measurements below the original rock surfaces.

Ming, Douglas W.↗

Moessbauer Mineralogical Evidence for Aqueous Processes at Gusev Crater and Meridiani Planum

The Moessbauer spectrometers on the MER rovers have measured the relative abundances of iron with respect to both oxidation state and iron-bearing phase at Gusev Crater (Spirit rover) and Meridiani Planum (Opportunity rover). The assemblage of phases indicates aqueous alteration processes at both landing sites. Although the rock and soil of the Gusev Crater plains are dominated by Fe(2+) in olivine-bearing basalt (approx.Fo60), a Fe(3+)-rich component (nanophase ferric oxide, np-Ox) has significant abundance in surface soils (13-28% of total Fe) and in the surface coatings (rinds) of certain rocks (39%) but not in rock interiors exposed by grinding (5-6%). The mode of occurrence of np-Ox implies that it is the product of oxidative alteration of Fe(2+) silicate and oxide phases in the presence of H2O. The ubiquitous presence of sulfur in soil and in rock coatings, as determined by the MER-A APXS instrument, suggests that the alteration occurred under acid-sulfate conditions, so that both hydrolytic and sulfatic reactions are viable. A possible source for the weathering agents is volcanic emanations rich in H2O and SO2. Generally, rocks in the Columbia Hills are significantly more altered than those in the Gusev plains, with a higher proportion of Fe(3+) oxide phases compared to Fe(2+) silicate phases. This mineralogical dichotomy implies a difference in the timing, rate, duration, and/or mechanism of alteration for basaltic material in the Gusev plains compared to basaltic material in the Columbia Hills. It is possible, for example, that the basaltic material in the Columbia Hills underwent aqueous alteration in a paleoclimate that favored nearly complete alteration and that the basaltic material of the Gusev plains will not achieve the degree of alteration exhibited by the Columbia Hills under current martian surface conditions.

Morris, R. V.↗

A Force-Controllable Macro-Micro Manipulator and its Application to Medical Robotics

This paper describes an 8-degrees-of-freedom macro-micro robot. This robot is capable of performing tasks that require accurate force control, such as polishing, finishing, grinding, deburring, and cleaning. The design of the macro-micro mechanism, the control algorithms, and the hardware/sofware implemtation of the algotithms are described in this paper. Initial experimental results are reported.

Robots↗

Electro-Chemically Enhanced Mechanical Polishing of Nickel Mandrels

Grinding and mechanical polishing techniques used for x-ray optics mandrel figuring lead to mid-frequency surface ripple. These small figure variations have to be addressed in order to improve the performance of the resulting x-ray mirrors. If the electrochemical etching is combined with mechanical polishing, the figuring and the surface finishing cm be done simultaneously and be used to correct the mid-frequency surface ripple. It is shown that the electrochemical mechanical polishing method allows selective removal of nickel alloy without mandrel surface microroughness degradation.

Gubarev, Mikhail↗

Turbulent Size Selection and Concentration of Chondrule-Sized Objects: Reynolds Number Invariance and Implications

It is generally agreed that individual chondrules formed as entities in a gaseous nebula prior to being accumulated into a meteorite parent body, within which they incur various forms of modification before arriving in our labs. While there are major unanswered questions about the properties of the nebula environment in which chondrules formed, the process by which the most primitive meteorites are formed overwhelmingly from chondrules must then be an aspect of "nebula processing". Textures in certain fragments of primitive meteorites might be summarized as being primarily chondrules and clastic, chondrule-sized, fragments of other minerals, each covered with a rim of fine dust with physical and chemical properties which are essentially independent of the composition and mineralogy of the underlying chondrule. This (unfortunately rather rare) texture was called "primary accretionary texture" to reflect their belief that it precedes subsequent stages in which fragmentation, comminution, mixing, heating, and other forms of alteration occur on the parent body(-ies). The size distribution of these chondrules and fragments, and the properties of their dusty rims, are key clues regarding the primary nebula accretion process. Even in the much more abundant meteorites which have clearly suffered internal mixing, abrasion, grinding, and even mineralogical alteration or replacement (due presumably to the collisional growth and heating process itself), key chondrule properties such as mean size and density remain relatively well defined, and well defined rims persist in many cases. It has been our goal to infer the key nebula processes indirectly from the properties of these very earliest primitive meteorites by making use of a theoretical framework in which the nebula possesses a plausible level of isotropic turbulence. We have shown that turbulence has the property of concentrating one particular particle size by orders of magnitude, where the preferentially concentrated size depends primarily on the intensity of the turbulent kinetic energy (represented by the Reynolds number of the nebula). Specifically, the preferentially concentrated particle is that which has a stopping time equal to the turnover time of the smallest eddy. The intensity level of turbulence implied by chondrule sizes can be maintained by even a small fraction of the energy released by the radially evolving disk (it must be noted that the details of how this transfer of energy actually occurs remain obscure, however).

Cuzzi, J. N.↗

Mars Exploration Rover Pancam Multispectral Imaging of Rocks, Soils, and Dust at Gusev Crater and Meridiani Planum

Multispectral imaging from the Panoramic Camera (Pancam) instruments on the Mars Exploration Rovers Spirit and Opportunity has provided important new insights about the geology and geologic history of the rover landing sites and traverse locations in Gusev crater and Meridiani Planum. Pancam observations from near-UV to near-IR wavelengths provide limited compositional and mineralogic constraints on the presence abundance, and physical properties of ferric- and ferrous-iron bearing minerals in rocks, soils, and dust at both sites. High resolution and stereo morphologic observations have also helped to infer some aspects of the composition of these materials at both sites. Perhaps most importantly, Pancam observations were often efficiently and effectively used to discover and select the relatively small number of places where in situ measurements were performed by the rover instruments, thus supporting and enabling the much more quantitative mineralogic discoveries made using elemental chemistry and mineralogy data. This chapter summarizes the major compositionally- and mineralogically-relevant results at Gusev and Meridiani derived from Pancam observations. Classes of materials encountered in Gusev crater include outcrop rocks, float rocks, cobbles, clasts, soils, dust, rock grindings, rock coatings, windblown drift deposits, and exhumed whitish/yellowish salty soils. Materials studied in Meridiani Planum include sedimentary outcrop rocks, rock rinds, fracture fills, hematite spherules, cobbles, rock fragments, meteorites, soils, and windblown drift deposits. This chapter also previews the results of a number of coordinated observations between Pancam and other rover-based and Mars-orbital instruments that were designed to provide complementary new information and constraints on the mineralogy and physical properties of martian surface materials.

Bell, J. F., III↗

Restoration Process

In the accompanying photos, a laboratory technician is restoring the once-obliterated serial number of a revolver. The four-photo sequence shows the gradual progression from total invisibility to clear readability. The technician is using a new process developed in an applications engineering project conducted by NASA's Lewis Research Center in conjunction with Chicago State University. Serial numbers and other markings are frequently eliminated from metal objects to prevent tracing ownership of guns, motor vehicles, bicycles, cameras, appliances and jewelry. To restore obliterated numbers, crime laboratory investigators most often employ a chemical etching technique. It is effective, but it may cause metal corrosion and it requires extensive preparatory grinding and polishing. The NASA-Chicago State process is advantageous because it can be applied without variation to any kind of metal, it needs no preparatory work and number recovery can be accomplished without corrosive chemicals; the liquid used is water.

Source record↗

Abernathy's Lap

A lap in this instance is not a midriff but a tool for presision.polishing and grinding. During the Saturn V moonbooster program, Marshall Space Flight Center found a need for a better lap. The need arose from the exquisitely precise tolerances required for parts of the launch vehicle's guidance,and control system. So William J. Abernathy, a former Marshall employee, built a better lap; he invented a method for charging aluminum lap plates with diamond powder, then hard-anodizing them. The resulting lap produces a high polish on materials ranging from the softest aluminum to the hardest ceramics. It operates faster, wears longer and requires less reworking. Abernathy got NASA's permission to obtain a personal patent and he formed the one-man Abernathy Laps Co. in Huntsville, which produces a variety of laps. One of Abernathy's customers is Bell Aerospace Textron, Buffalo, which uses the laps to finish polish delicate instrument parts produced for NASA's Viking and other space programs. Says a Bell official: "Time needed (with the Abernathy lap) is a fraction of that required by conventional methods. The result is extremely accurate flatness and surface finish." Abernathy is providing laps for other manufacturing applications and for preparation of metallurgical specimens. The business is small but steady, and Abernathy plans expansion into other markets.

Source record↗

U-937 Toxicity Testing of Lunar Dust Stimulant (JSC-1A-vf)

With NASA planning to extend the human presence to the moon by 2020, the dangers of the lunar environment must be assessed and appropriate countermeasures must be developed. Possible toxic effects of the lunar dust are of particular importance to human health because of the dust's chemical composition, reactivity, and small size. This project focuses on the toxicity of lunar dust stimulant (JSC-1A-vf), in both its active and passive forms, using U-937 human monocyte cells. Simulant was mechanically activated from its passive form by grinding, and its ability to produce hydroxyl radicals was determined. To test for toxicity, active and passivated simulant was diluted in media and applied to the cells for various time periods. Toxicity was then estimated using flow cytometry on the Guava Personal Cell Analysis system. Preliminary results suggest that passivated stimulant is slightly toxic, with an increase in toxicity for activated stimulant. Toxicity results may be affected by cell lysing behavior and quenching of hydroxyl radical production by the cell media.

Bales, Kristyn↗