Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLAME”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Effects of Confinement on Flame Spread in Microgravity

Solid fuel combustion experiments aboard the ISS examine the effects of confinement on a concurrent, purely-forced-flow flame spread in microgravity environment. The results for a thin, cotton-fiberglass-blended textile fabric fuel are presented. Flat baffles of differing materials are used to alter the radiative boundary conditions with transparent polycarbonate, black anodized aluminum (reflectance ~ 0), and highly polished aluminum (reflectance ~ 1). The baffles are parallel to the fuel sheet and placed symmetrically on each side. The inter-baffle distance is varied to change the boundary conditions for the flow. In all tests, samples are ignited at the upstream leading edge and allowed to burn to completion. Results show that the flame reaches a steady length and spread rate at low flow speeds (< 15 cm/s) for all tested inter-baffle distances. As the distance decreases, the flame length and spread rate first increase then decrease showing an optimal inter-baffle distance. For all baffle types, the flame either fails to ignite or extinguishes before reaching the end of the sample when the inter-baffle distance is too small (~ 1 cm). This is attributed to the reduction of oxygen supply to the flame zone and heat loss to the baffles. The results also show at the same inter-baffle distance, flame length and spread rate are highest for polished aluminum baffles, and lowest for transparent polycarbonate baffles. The differences are most prominent at intermediate tested baffle distances. While the radiative heat feedback from the baffles is expected to increase when the baffle distance decreases, the combustion is limited by the reduced oxygen supply. Near this limit, flame lengths and spread rates are similar for all baffle types.

Microgravity↗

Effect of NO on extinction and re-ignition of vortex-perturbed hydrogen flames.

The catalytic effect of nitric oxide (NO) on the dynamics of extinction and re-ignition of a vortex-perturbed non-premixed hydrogen-air flame is studied in a counterflow burner. A diffusion flame is established with counterflowing streams of nitrogen-diluted hydrogen at ambient temperature and air heated to a range of temperatures that brackets the auto-ignition temperature. Localized extinction is induced by impulsively driving a fuel-side toroidal vortex into the steady flame, and the recovery of the extinguished region is monitored by planar laser-induced fluorescence (PLIF) of the hydroxyl radical (OH). The dynamics of flame recovery depend on the air temperature and fuel concentration, and four different recovery modes are identified. These modes involve combinations of edge-flame propagation and the expansion of an auto-ignition kernel that forms within the extinguished region. The addition of a small amount of NO significantly alters the re-ignition process by shifting the balance between chain-termination and chain-propagation reactions to enhance auto-ignition. The ignition enhancement by this catalytic effect causes a shift in the conditions that govern the recovery modes. In addition, the effects of NO concentration and vortex strength on the flame recovery are examined. Direct numerical simulations of the flame-vortex interaction with and without NO doping show how the small amount of OH produced by NO-catalyzed reactions has a significant impact on the development of an auto-ignition kernel. This joint experimental and numerical study provides detailed insight into the interaction between transient flows and ignition processes.

08 HYDROGEN↗

A 2-D DNS investigation of extinction and reignition dynamics in nonpremixed flame-vortex interactions

Two-dimensional (2-D) DNS investigations of extinction and reignition dynamics during interactions of laminar nonpremixed flames with counterrotating vortex pairs are performed. The length and velocity scales chosen for the vortices are representative of those in the near fields of high-Reynolds-number jets such as those occurring in Diesel engines. The governing equations are solved with sixth-order spatial discretization and fourth-order time integration. Chemistry is modeled as an irreversible single-step reaction. Local extinction along the symmetry axis, followed by reignition, is observed. The extinction is characterized by strong unsteady effects, which are captured well by 1-D transient diffusion flamelet libraries, provided the time-history of the instantaneous scalar dissipation rate is taken into account. On the other hand, reignition is essentially a 2-D phenomenon involving flame-flame interactions, which are favored for smaller vortices and increasing flame curvature. The effects of unsteadiness and curvature on extinction and reignition are carefully assessed through parametric studies involving a range of vortex and flame characteristics. The interaction outcomes are summarized on Reynolds-Damkoehler number (Re-Da) diagrams, which show the combined effects of unsteadiness and curvature on extinction and reignition. The implications of the observed interaction outcomes for turbulent combustion modeling in the near fields of jet diffusion flames are discussed. (author)

33 ADVANCED PROPULSION SYSTEMS↗

Dynamics of premixed hydrogen/air flames in mesoscale channels

Direct numerical simulation with detailed chemistry and transport is used to study the stabilization and dynamics of lean ({phi}=0.5) premixed hydrogen/air atmospheric pressure flames in mesoscale planar channels. Channel heights of h=2, 4, and 7 mm, and inflow velocities in the range 0.3{<=}U{sub IN}{<=}1100cm/ s are investigated. Six different burning modes are identified: mild combustion, ignition/extinction, closed steady symmetric flames, open steady symmetric flames, oscillating and, finally, asymmetric flames. Chaotic behavior of cellular flame structures is observed for certain values of U{sub IN}. Stability maps delineating the regions of the different flame types are finally constructed. (author)

08 HYDROGEN↗

Characteristics of liquid ethanol diffusion flames from mini tube nozzles

A series of experiments was conducted to explore the combustion characteristics of a diffusion flames from mini tubes fueled by liquid ethanol with visual observations of the flame shape, the dynamic liquid-vapor interface during phase change inside the capillary tubes and the tube outer surface temperature using CCD and IR cameras. As the fuel supply rate increased, the interface location rose to the tube exit and the temperature gradient on the outer tube surface increased, consequently the evaporating became much stronger and the interface tended to be unstable. The combustion characteristics are closely related to the rapid phase change and violent evaporation and interfacial dynamics, with the violent evaporation, actually explosive boiling, inducing an explosive flame. The intensity of the explosive flame became stronger as the flowrate increased with the maximum flame height, interface location movement, and sound intensity all significantly increasing. The periodicity of the explosive flame was directly proportional to the interface moving distance and inversely proportional to the fuel flow rate. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Autoignited laminar lifted flames of propane in coflow jets with tribrachial edge and mild combustion

Characteristics of laminar lifted flames have been investigated experimentally by varying the initial temperature of coflow air over 800 K in the non-premixed jets of propane diluted with nitrogen. The result showed that the lifted flame with the initial temperature below 860 K maintained the typical tribrachial structure at the leading edge, which was stabilized by the balance mechanism between the propagation speed of tribrachial flame and the local flow velocity. For the temperature above 860 K, the flame was autoignited without having any external ignition source. The autoignited lifted flames were categorized in two regimes. In the case with tribrachial edge structure, the liftoff height increased nonlinearly with jet velocity. Especially, for the critical condition near blowout, the lifted flame showed a repetitive behavior of extinction and reignition. In such a case, the autoignition was controlled by the non-adiabatic ignition delay time considering heat loss such that the autoignition height was correlated with the square of the adiabatic ignition delay time. In the case with mild combustion regime at excessively diluted conditions, the liftoff height increased linearly with jet velocity and was correlated well with the square of the adiabatic ignition delay time. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Flame-synthesis limits and self-catalytic behavior of carbon nanotubes using a double-faced wall stagnation flow burner

Flame-synthesis limits of carbon nanotubes (CNTs) are measured using a double-faced wall stagnation flow (DWSF) burner that shows potential in mass production of CNTs. With nitrogen-diluted premixed ethylene-air flames established on the nickel-coated stainless steel double-faced plate wall, the limits of CNT formation are determined using field-emission scanning and transmission electron microscopies and Raman spectroscopy. Also, self-catalytic behavior of the synthesized CNTs is evaluated using the DWSF burner with a CNT-deposited stainless steel double-faced plate wall. Results show narrow fuel-equivalence ratio limits of multi-walled CNT (MWCNT)-synthesis at high flame stretch rates and substantially extended limits at low flame stretch rates. This implies that the synthesis limits are very sensitive to the fuel-equivalence ratio variation for the high stretch rate conditions, yielding a lot of impurities and soot rather than MWCNTs. The enhanced ratio of tube inner diameter to wall thickness of the MWCNTs synthesized using a CNT self-catalytic flame-synthesis process is observed, indicating that the quality of metal-catalytic, flame-synthesized MWCNTs can be much improved via the process. Thus, using a DWSF burner with the CNT self-catalytic process has potential in mass production of MWCNTs with improved quality. (author)

36 MATERIALS SCIENCE↗

Composition PDF/photon Monte Carlo modeling of moderately sooting turbulent jet flames

A comprehensive model for luminous turbulent flames is presented. The model features detailed chemistry, radiation and soot models and state-of-the-art closures for turbulence-chemistry interactions and turbulence-radiation interactions. A transported probability density function (PDF) method is used to capture the effects of turbulent fluctuations in composition and temperature. The PDF method is extended to include soot formation. Spectral gas and soot radiation is modeled using a (particle-based) photon Monte Carlo method coupled with the PDF method, thereby capturing both emission and absorption turbulence-radiation interactions. An important element of this work is that the gas-phase chemistry and soot models that have been thoroughly validated across a wide range of laminar flames are used in turbulent flame simulations without modification. Six turbulent jet flames are simulated with Reynolds numbers varying from 6700 to 15,000, two fuel types (pure ethylene, 90% methane-10% ethylene blend) and different oxygen concentrations in the oxidizer stream (from 21% O{sub 2} to 55% O{sub 2}). All simulations are carried out with a single set of physical and numerical parameters (model constants). Uniformly good agreement between measured and computed mean temperatures, mean soot volume fractions and (where available) radiative fluxes is found across all flames. This demonstrates that with the combination of a systematic approach and state-of-the-art physical models and numerical algorithms, it is possible to simulate a broad range of luminous turbulent flames with a single model. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Temporally resolved planar measurements of transient phenomena in a partially pre-mixed swirl flame in a gas turbine model combustor

This paper presents observations and analysis of the time-dependent behavior of a 10 kW partially pre-mixed, swirl-stabilized methane-air flame exhibiting self-excited thermo-acoustic oscillations. This analysis is based on a series of measurements wherein particle image velocimetry (PIV) and planar laser-induced fluorescence (PLIF) of the OH radical were performed simultaneously at 5 kHz repetition rate over durations of 0.8 s. Chemiluminescence imaging of the OH{sup *} radical was performed separately, also at 5 kHz over 0.8 s acquisition runs. These measurements were of sufficient sampling frequency and duration to extract usable spatial and temporal frequency information on the medium to large-scale flow-field and heat-release characteristics of the flame. This analysis is used to more fully characterize the interaction between the self-excited thermo-acoustic oscillations and the dominant flow-field structure of this flame, a precessing vortex core (PVC) present in the inner recirculation zone. Interpretation of individual measurement sequences yielded insight into various physical phenomena and the underlying mechanisms driving flame dynamics. It is observed for this flame that location of the reaction zone tracks large-scale fluctuations in axial velocity and also conforms to the passage of large-scale vortical structures through the flow-field. Local extinction of the reaction zone in regions of persistently high principal compressive strain is observed. Such extinctions, however, are seen to be self healing and thus do not induce blowout. Indications of auto-ignition in regions of unburned gas near the exit are also observed. Probable auto-ignition events are frequently observed coincident with the centers of large-scale vortical structures, suggesting the phenomenon is linked to the enhanced mixing and longer residence times associated with fluid at the core of the PVC as it moves through the flame. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fuel-structure dependence of benzene formation processes in premixed flames fueled by C 6 H 12 isomers

The fuel-structure-dependent significance of various benzene formation pathways is analyzed using data from rich (phi = 1.7) flames fueled by four C6H12 isomers: 1-hexene, cyclohexane, methylcyclopentane, and 3,3-dimethyl-1-butene. The isomer-resolved chemical compositions of the four premixed, laminar low-pressure flat flames are determined by flame-sampling molecular-beam mass spectrometry employing single-photon ionization by synchrotron generated vacuum-ultraviolet photons. Isomer-resolving photo-ionization efficiency curves and quantitative mole fraction profiles reveal the dominant fuel destruction pathways, the influence of different fuel consumption processes on the formation of commonly considered benzene precursors, and the contributions of several routes towards benzene formation. While propargyl and allyl radicals dominate benzene formation in the combustion of 1-hexene, contributions from reactions involving i-C4H5 and C5H5 radicals are revealed in the flames of 3,3-dimethyl-1-butene and methylcyclopentane, respectively. Close to the burner surface, successive dehydrogenation of the fuel is found to be important for the cyclohexane flame and to some smaller extent for the methylcyclopentane flame. (C) 2010 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

1-HEXENE OXIDATION↗

Quantitative acetylene measurements in laminar and turbulent flames using 1D Raman/Rayleigh scattering

Our research presents the extension of the established detection of seven major species in 1D Raman/Rayleigh measurements to incorporate acetylene (C 2 H 2 ) as an eighth species. Acetylene is an important soot precursor which is generated in hydrocarbon flames as an intermediate species following decomposition. It occurs over a broad temperature range in flames and has been identified as a potentially detectable species in 1D Raman/Rayleigh measurements. In this paper, we discuss the Raman spectral signature of acetylene, its temperature dependence, calibration procedures, and the interference with other Raman-active species, C 2 and broadband interferences, all of which are essential to quantify for accurate data processing. In this regard, Raman measurements in laminar and turbulent dimethyl ether flames were acquired. The data are spectrally analyzed and low-temperature calibrations of the Raman response are combined with an extrapolation model for high temperatures in order to place the acetylene signals on an absolute scale. Single-shot and conditional-mean values are presented as a function of mixture fraction for a laminar partially-premixed DME/air flame. Measurements from the laminar flame are compared to a 1D laminar flame calculation to assess the accuracy of the calibration and analysis procedures. Furthermore, detection limits, signal-to-noise, and signal-to-interference ratio of the C 2 H 2 measurement are discussed, and single-shot measurements of acetylene in a turbulent DME/air jet flame are demonstrated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

3D simulations of spinlike flames in Co/Al multilayers with enhanced conduction losses

Reactive Co/Al multilayers are uniformly structured materials that may be ignited to produce rapid and localized heating. Prior studies varying the bilayer thickness (i.e., sum of two individual layers of Co and Al) have revealed different types of flame morphologies, including: (a) steady/planar, (b) wavy/periodic, and (c) transverse bands, originating in the flame front. These instabilities resemble the “spin waves” first observed in the early studies of solid combustion (i.e., Ti cylinder in a N 2 atmosphere), and are likewise thought to be due to the balance of heat released by reaction and heat conduction forward into the unreacted multilayer. However, the multilayer geometry and three-dimensional (3D) edge effects are relatively unexplored. In this work, a new diffusion-limited reaction model for Co/Al multilayers was implemented in large, novel 3D finite element analysis (FEA) simulations, in order to study the origins of these spinlike flames. This reaction model builds upon previous work by introducing three new phase-dependent property models for: (1) the diffusion coefficient, (2) anisotropic thermal conductivity tensor, and (3) bulk heat capacity, as well as one additional model for the bilayer-dependent heat of reaction. These novel 3D simulations are the first to predict both steady and unsteady flames in Co/Al multilayers. Moreover, two unsteady modes of flame propagation are identified, which depend on the enhanced conduction losses with slower flames, as well as flame propagation around notched edges. Finally, future work will consider the generality of the current modeling approach and also seek to define a more generalized set of stability criteria for additional multilayer systems.

42 ENGINEERING↗

On velocity and reactive scalar spectra in turbulent premixed flames

Abstract Kinetic energy and reactive scalar spectra in turbulent premixed flames are studied from compressible three-dimensional direct numerical simulations (DNS) of a temporally evolving rectangular slot-jet premixed flame, a statistically one-dimensional configuration. The flames correlate to a lean premixed hydrogen–air mixture at an equivalence ratio of 0.7, preheated to 700 K and at 1 atm, and three DNS are considered with a fixed jet Reynolds number of 10 000 and a jet Damköhler number varying between 0.13 and 0.54. For the study of spectra, motivated by the need to account for density change, which can be locally strong in premixed flames, a new density-weighted definition for two-point velocity/scalar correlations is proposed. The density-weighted two-point correlation tensor retains the essential properties of its constant-density (incompressible) counterpart and recovers the density-weighted Reynolds stress tensor in the limit of zero separation. The density weighting also allows the derivation of balance equations for velocity and scalar spectrum functions in the wavenumber space that illuminate physics unique to combusting flows. Pressure–dilatation correlation is a source of kinetic energy at high wavenumbers and, analogously, reaction rate–scalar fluctuation correlation is a high-wavenumber source of scalar energy. These results are verified by the spectra constructed from the DNS data. The kinetic energy spectra show a distinct inertial range with a $\def \xmlpi #1{}\def \mathsfbi #1{\boldsymbol {\mathsf {#1}}}\let \le =\leqslant \let \leq =\leqslant \let \ge =\geqslant \let \geq =\geqslant \def \Pr {\mathit {Pr}}\def \Fr {\mathit {Fr}}\def \Rey {\mathit {Re}}-5/3$ scaling followed by a ‘diffusive–reactive’ range at higher wavenumbers. The exponential drop-off in this range shows a distinct inflection in the vicinity of the wavenumber corresponding to a laminar flame thickness, $\delta _L$ , and this is attributed to the contribution from the pressure–dilatation term in the energy balance in wavenumber space. Similarly, a clear spike in spectra of major reactant species (hydrogen) arising from the reaction-rate term is observed at wavenumbers close to $\delta _L$ . It appears that in the inertial range classical scaling laws for the spectra involving the Kolmogorov scale are applicable, but in the high-wavenumber range where chemical reactions have a strong signature the laminar flame thickness produces a better collapse. It is indicated that a full scaling should perhaps involve the Kolmogorov scale, laminar flame thickness, Damköhler number and Karlovitz number.

42 ENGINEERING↗

Simulation of Premixed and Partially Premixed Jet-in-Crossflow Flames at High Pressure

In this paper, we explore the operational map of a lean axial-staged combustor of premixed and partially premixed reacting jet-in-crossflow flames at high -pressure (5 atm). This study attempts to expand the data to relatively high pressure and could significantly aid scaling to real gas turbine engine conditions at 20–30 atm. High-speed camera, particle image velocimetry (PIV), CH* chemiluminescence, temperature, and pressure measurements were taken and processed to allow accurate reconstruction of six operating points relative to computational fluid dynamics (CFD) simulations under minimal adjustments. Variation of lean main stage (φ = 0.575 and 0.73) and rich jet (φ = 1.1, 4, and 8) equivalence ratio has been investigated for a four mm axial jet. The fully premixed flames were found to be controlled by the crossflow temperature before ignition and the crossflow oxygen content during combustion. Analysis of flame shape and position for the partially premixed operating points describes a lee stabilized as well as a more unsteady windward flame branch. Adjustment of added jet fuel and crossflow temperature along with its corresponding oxygen level is required to attain a compact flame body. Here, the risk of delaying combustion progress is significantly increased at a richer jet φ = 8 and an overshooting, spatially divided flame was attained with a main stage φ = 0.73. Control toward a compact flame body is critical to allow combustion at reasonable reaction rate.

03 NATURAL GAS↗

Emissions and Flame Structure Assessment of Aeroengine Micromixing Injectors for Lean Direct Injection of Hydrogen and Hydrogen/Natural Gas Blends

Abstract The present study focuses on whether adapting low emissions liquid fuel injection concepts can be applied to gaseous mixtures. The goal is to develop an injector with specific geometric characteristics that will achieve the lowest emissions. This is conducted by evaluating emissions and flame diagnostics on a set of test hardware that has been developed for combustion of pure hydrogen and hydrogen/methane mixtures. The current test hardware adapts lean direct injection concepts from aeroengine injectors to a ground-based engine based on target flows associated with a Solar Turbines Industrial Engine gas turbine. A statistical test plan was developed to assess these geometric characteristics using a three level Box Behnken design. The test plan investigates the effect of injector flow splits, air swirl, fuel swirl, pressure drop, preheat temperature, fuel composition, and the adiabatic flame temperature on the flame structure and emissions performance. A total of 16 injectors were considered for a total of 688 test points for emission and imaging data. Emissions data were reported on a mass basis in ng/J and chemical reactor network analysis were conducted to further interpret emissions behavior. Images were also captured to analyze the flame structure features of interest including reaction volume, flame length, flame spread, and flame width. With these results, a predictive model for emissions was made to conclude the most optimal injector configuration is to have the highest level of air split (more volume of air through the injector plate versus the injector) and air swirl angle for both methane and hydrogen gas mixtures. The predictive emissions level for all of these cases were below 10 ng/J.

08 HYDROGEN↗

DNS of Flame Stabilization Dynamics of a Swirl-Stabilized Spray Burner Using Sustainable Aviation Fuels

Concern for emission reduction has motivated the development of new cost-effective alternative sustainable aviation fuels (SAFs). Drop-in SAFs with blends of the certified and the alternative fuels are beneficial because they do not require engine modifications for use in current aviation engines. Combustion characteristics are of particular concern when comparing a new fuel with Jet-A. Lean blow-off and flame stabilization have been identified to be governed by the fuel propensity to autoignition, i.e. derived cetane number. However, fundamental investigation is required to identify the impact of derived cetane number on the combustion mode of flame stabilization in a realistic combustor. The combustion mode has also a direct impact on turbulent combustion modeling closures. DNS simulations are performed in the low-Mach solver of the Pele Suite called PeleLMeX. Lagrangian multi-phase modeling is used to capture the liquid spray injection of Jet-A (reference fuel) and C1 as a representative of a low cetane number SAF. Adaptive Mesh Refinement (AMR) is used to enable a more efficient simulation of a more realistic domain size and embedded boundary treatment is used to model a bluff-body geometry. Local extinction and edge flame propagation were observed for both fuels. The edge flame propagation mode was quantified in terms of a Damkohler number defined as the ratio between progress variable reaction rate and its diffusive flux. Initial analysis suggests that a mixed mode combustion occurs for the edge flame propagation, with flame propagation assisted by ignition and autoignition co-existing for both Jet-A and C1 flames. The analysis of the extinction region shows a larger progress variable for Jet-A which can further increase the local displacement speed and present a faster reignition of the stoichiometric mixture fraction.

adaptive mesh refinement↗

Dynamics of Laterally Propagating Flames in X-Ray Bursts. II. Realistic Burning and Rotation

In this work, we continue to investigate two-dimensional laterally propagating flames in type I X-ray bursts using fully compressible hydrodynamics simulations. In the current study we relax previous approximations where we artificially boosted the flames. We now use more physically realistic reaction rates, thermal conductivities, and rotation rates, exploring the effects of neutron star rotation rate and thermal structure on the flame. We find that at lower rotation rates the flame becomes harder to ignite, whereas at higher rotation rates the nuclear burning is enhanced by increased confinement from the Coriolis force and the flame propagates steadily. At higher crustal temperatures, the flame moves more quickly and accelerates as it propagates through the atmosphere. If the temperature is too high, instead of a flame propagating across the surface the entire atmosphere burns uniformly. Our findings could have implications for the relationship between observed burst rise times and neutron star rotation and accretion rates. All of the software used for these simulations is freely available.

79 ASTRONOMY AND ASTROPHYSICS↗

EGR Dilution and Fuel Property Effects on High-Efficiency Spark-Ignition Flames

Modern spark ignition internal combustion engines rely on fast combustion rates and high dilution to achieve high brake thermal efficiencies. To accomplish this, new engine designs have moved towards increased tumble ratios and stroke-to-bore ratios. Increased tumble ratios correlate positively with increases in turbulent kinetic energy and improved fuel and residual gas mixing, all of which favor faster and more efficient combustion. Longer stroke-to-bore ratios allow higher geometric compression ratios and use of late intake valve closing to control peak compression pressures and temperatures. The addition of dilution to improve efficiency is limited by the resulting increase in combustion instabilities manifested by cycle-to-cycle variability. A number of effects - preferential diffusion, turbulence-combustion interactions, stochastic flow patterns, laminar-turbulent flame kernel transitions, and relative length and velocity scales between flame and turbulence - are believed to be responsible for the increase in cycle-to-cycle variations, where their contributions are likely interlinked. Several studies have shown the influence of stochastic flow characteristics on the nature of combustion instabilities, such as velocity patterns on flame kernel formation and cycle-to-cycle variations in residual gas. However, few have focused on the specific effects of fuel properties. The objective of this work is to contrast the effects of dilution on propane stoichiometric combustion against gasoline. Dilution tolerance experiments were conducted in a purpose-built high stroke-to-bore ratio single cylinder engine with both gasoline and LPG. Three-dimensional full cycle computational fluid dynamics (CFD) simulations employing a level-set combustion approach and Reynolds averaged Navier-Stokes (RANS) turbulence modeling was used to qualitatively assess the changes in length and velocity scales for turbulence and the flame. The experimental results showed that LPG can tolerate higher exhaust gas recirculation (EGR) dilution under a variety of conditions. Analysis of CFD simulations showed that propane flames are likely less sensitive to influences from the flow field due to less thickening of the flame and higher effective flame speeds.

33 ADVANCED PROPULSION SYSTEMS↗