SEARCH · Engineering Papers

Results for “Elliptic problems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

All sources NASA NTRS DOE OSTI

NASA NTRS2020

Bearing Anomaly for the Sentinel 6 Supplemental Calibration System

The Supplemental Calibration System (SCS) was designed to rotate an elliptical reflector for the Sentinel 6 Advanced Microwave Radiometer (AMR). By rotating the reflector, the system can perform calibrations by comparing the reflection from space to the reflection from an onboard calibration target. During the qualification testing of the SCS, a flaw was discovered that resulted in apparent brinelling of bearings that support the rotating reflector. An extensive investigation ensued to determine the root cause of the problem. Though the most likely root causes of the presumed brinelling ended up being the result of undersized bearing clamp rings and thermal mismatch, there were requirements that drove these design choices. This paper describes the design of the bearing assembly, requirements that drove the design, and documents a challenging investigation filled with ambiguous test results.

Paulsen, Gale↗

NASA NTRS1988

Incompressible and anelastic flow simulations on numerically generated grids

In the numerical simulation of incompressible and anelastic flows, it is necessary to solve an elliptic equation at each time step. When the boundaries of such flows are nonrectangular, it may be advantageous to solve the equations on a new, numerically generated coordinate grid, in which the property of orthogonality has been preserved. Flow equations in general curvilinear coordinates maintaining the conservative form are given for both anelastic models using the momentum equations, and for incompressible models, using the vorticity equation. The general problem of grid-generation in two dimensions is presented, and a quasi-conformal transformation technique is discussed in detail. Some examples of grids generated by this technique are exhibited. Three examples of the flow of a stratified fluid over obstacles are presented, in which the grid-generation permits some new results to be obtained.

Sharman, R. D.↗

DOE OSTI2018

Large-Time Behavior of Solutions to Vlasov-Poisson-Fokker-Planck Equations: From Evanescent Collisions to Diffusive Limit

The present contribution investigates the dynamics generated by the two-dimensional Vlasov-Poisson-Fokker-Planck equation for charged particles in a steady inhomogeneous background of opposite charges. We provide global in time estimates that are uniform with respect to initial data taken in a bounded set of a weighted L{sup 2} space, and where dependencies on the mean-free path τ and the Debye length δ are made explicit. In our analysis the mean free path covers the full range of possible values: from the regime of evanescent collisions τ→∞ to the strongly collisional regime τ→0. As a counterpart, the largeness of the Debye length, that enforces a weakly nonlinear regime, is used to close our nonlinear estimates. Accordingly we pay a special attention to relax as much as possible the τ-dependent constraint on δ ensuring exponential decay with explicit τ-dependent rates towards the stationary solution. In the strongly collisional limit τ→0, we also examine all possible asymptotic regimes selected by a choice of observation time scale. Here also, our emphasis is on strong convergence, uniformity with respect to time and to initial data in bounded sets of a L{sup 2} space. Our proofs rely on a detailed study of the nonlinear elliptic equation defining stationary solutions and a careful tracking and optimization of parameter dependencies of hypocoercive/hypoelliptic estimates.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2023

A unified hp-HDG framework for Friedrichs' PDE systems

Here, this work proposes a unified hp-adaptivity framework for hybridized discontinuous Galerkin (HDG) method for a large class of partial differential equations (PDEs) of Friedrichs' type. In particular, we present unified hp-HDG formulations for abstract one-field and two-field structures and prove their well-posedness. In order to handle non-conforming interfaces we simply take advantage of HDG built-in mortar structures. With split-type mortars and the approximation space of trace, a numerical flux can be derived via Godunov approach and be naturally employed without any additional treatment. As a consequence, the proposed formulations are parameter-free. We perform several numerical experiments for time-independent and linear PDEs including elliptic, hyperbolic, and mixed-type to verify the proposed unified hp-formulations and demonstrate the effectiveness of hp-adaptation. Two adaptivity criteria are considered: one is based on a simple and fast error indicator, while the other is rigorous but more expensive using an adjoint-based error estimate. The numerical results show that these two approaches are comparable in terms of convergence rate even for problems with strong gradients, discontinuities, and singularities.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

Building a quantum computing architecture using 3D superconducting cavities

Quantum computers promise advantages over classical machines for solving certain complex problems, but building processors that truly deliver this advantage remains a central challenge, particularly due to limited coherence times. Three-dimensional superconducting radio-frequency (SRF) cavities offer an attractive platform due to their exceptionally long lifetimes. However, since these harmonic systems require nonlinear elements, such as transmons, for control, additional losses are often introduced. In this talk, I will present a multimode quantum system based on an elliptical SRF cavity hosting two cavity modes weakly coupled to an ancillary transmon circuit. This architecture is carefully engineered to preserve coherence while enabling efficient control. By optimizing the design to mitigate transmon-induced decoherence, we realize single-photon lifetimes of 20.6 ms and 15.6 ms in the two modes, with pure dephasing times exceeding 40 ms. Using sideband interactions and error-resilient protocols, such as measurement-based correction and post-selection, we demonstrate high-fidelity state control, including preparation of Fock states up to N=20 with fidelities above 95% (to our knowledge, the highest reported to date), as well as high-fidelity two-mode entanglement. These results highlight 3D SRF cavities as a robust foundation for qudit-based quantum information processing, harnessing the large Hilbert space of cavity modes. I will conclude by outlining strategies to further enhance coherence in both cavities and ancilla qubits, and discuss pathways toward scaling this architecture into a larger quantum computing platform.

Roy, Tanay [Fermilab]↗

NASA NTRS1993

An automatic multigrid method for the solution of sparse linear systems

An automatic version of the multigrid method for the solution of linear systems arising from the discretization of elliptic PDE's is presented. This version is based on the structure of the algebraic system solely, and does not use the original partial differential operator. Numerical experiments show that for the Poisson equation the rate of convergence of our method is equal to that of classical multigrid methods. Moreover, the method is robust in the sense that its high rate of convergence is conserved for other classes of problems: non-symmetric, hyperbolic (even with closed characteristics) and problems on non-uniform grids. No double discretization or special treatment of sub-domains (e.g. boundaries) is needed. When supplemented with a vector extrapolation method, high rates of convergence are achieved also for anisotropic and discontinuous problems and also for indefinite Helmholtz equations. A new double discretization strategy is proposed for finite and spectral element schemes and is found better than known strategies.

Shapira, Yair↗

DOE OSTI2015

Dark matter voids in the SDSS galaxy survey

What do we know about voids in the dark matter distribution given the Sloan Digital Sky Survey (SDSS) and assuming the ΛCDM model? Recent application of the Bayesian inference algorithm BORG to the SDSS Data Release 7 main galaxy sample has generated detailed Eulerian and Lagrangian representations of the large-scale structure as well as the possibility to accurately quantify corresponding uncertainties. Building upon these results, we present constrained catalogs of voids in the Sloan volume, aiming at a physical representation of dark matter underdensities and at the alleviation of the problems due to sparsity and biasing on galaxy void catalogs. To do so, we generate data-constrained reconstructions of the presently observed large-scale structure using a fully non-linear gravitational model. We then find and analyze void candidates using the VIDE toolkit. Our methodology therefore predicts the properties of voids based on fusing prior information from simulations and data constraints. For usual void statistics (number function, ellipticity distribution and radial density profile), all the results obtained are in agreement with dark matter simulations. Our dark matter void candidates probe a deeper void hierarchy than voids directly based on the observed galaxies alone. The use of our catalogs therefore opens the way to high-precision void cosmology at the level of the dark matter field. We will make the void catalogs used in this work available at http://www.cosmicvoids.net.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1982

Numerical grid generation; Proceedings of the Symposium on Numerical Generation of Curvilinear Coordinate Systems and Their Use in the Numerical Solution of Partial Differential Equations, Nashville, TN, April 13-16, 1982

General curvilinear coordinate systems are considered along with the error induced by coordinate systems, basic differential models for coordinate generation, elliptic grid generation, conformal grid generation, algebraic grid generation, orthogonal grid generation, patched coordinate systems, and solid mechanics applications of boundary fitted coordinate systems. Attention is given to coordinate system control and adaptive meshes, the application of body conforming curvilinear grids for finite difference solution of external flow, the use of solution adaptive grids in solving partial differential equations, adaptive gridding for finite difference solutions to heat and mass transfer problems, and the application of curvilinear coordinate generation techniques to the computation of internal flows. Other topics explored are related to the solution of nonlinear water wave problems using boundary-fitted coordinate systems, the numerical modeling of estuarine hydrodynamics on a boundary-fitted coordinate system, and conformal grid generation for multielement airfoils.

Thompson, J. F.↗

NASA NTRS1986

Parameter estimation problems for distributed systems using a multigrid method

The problem of estimating spatially varying coefficients of partial differential equations is considered from observation of the solution and of the right hand side of the equation. It is assumed that the observations are distributed in the domain and that enough observations are given. A method of discretization and an efficient multigrid method for solving the resulting discrete systems are described. Numerical results are presented for estimation of coefficients in an elliptic and a parabolic partial differential equation.

Taasan, S.↗

NASA NTRS1989

Application of a self-adaptive grid method to complex flows

A directional-split, modular, user-friendly grid point distribution code is applied to several test problems. The code is self-adaptive in the sense that grid point spacing is determined by user-specified constants denoting maximum and minimum grid spacings and constants relating the relative influence of smoothness and orthogonality. Estimates of truncation error, in terms of flow-field gradients and/or geometric features, are used to determine the point distribution. Points are redistributed along grid lines in a specified direction in an elliptic manner over a user-specified subdomain, while orthogonality and smoothness are controlled in a parabolic (marching) manner in the remaining directions. Multidirectional adaption is achieved by sequential application of the method in each coordinate direction. The flow-field solution is redistributed onto the newly distributed grid points after each unidirectional adaption by a simple one-dimensional interpolation scheme. For time-accurate schemes such interpolation is not necessary and time-dependent metrics are carried in the fluid dynamic equations to account for grid movement.

Deiwert, G. S.↗

NASA NTRS1990

Parameter estimation problems for distributed systems using a multigrid method

Ta'asan, Shlomo↗

NASA NTRS1999

Shuttle and Transfer Orbit Thermal Analysis and Testing of the Chandra X-Ray Observatory Charge-Couple Device Imaging Spectrometer Radiator Shades

Thermal analyses of the Shuttle and Transfer Orbit of the Advanced X-Ray Astrophysics Facility Charge-Coupled Device (CCD) Imaging Spectrometer (ACIS), one of two science instruments on the Chandra X-Ray Observatory, revealed a low-earth orbit (LEO) overheating problem on the goldized Kapton faces of two radiator shades. The shades were coated with the goldized Kapton to provide a low hemispherical emittance to minimize direct and backloaded heating from the sun and the observatory and high specularity to optimize the coupling to space on two passive radiators which cool the focal plane to -120 C +/- 1 C during on-orbit operations. Since the observatory has a highly elliptical final orbit of 10,000 kilometers by 140,000 kilometers and the ACIS radiators and shades are oriented anti-sun, the high solar absorptance to emittance ratio of the goldized Kapton was not an issue. However, during Shuttle bay-to-earth operations, the short duration solar heating occurring near the eclipse entry and exit resulted in shade temperatures in excess of the cure temperature of the adhesive used to bond the goldized Kapton and honeycomb face-sheets. The detailed thermal analysis demonstrating the LEO overheating as well as the redesign options and thermal testing of a redesigned development unit shade are presented.

Sharp, John R.↗

DOE OSTI2013

On the offset of barred galaxies from the black hole M {sub BH}-σ relationship

We use collisionless N-body simulations to determine how the growth of a supermassive black hole (SMBH) influences the nuclear kinematics in both barred and unbarred galaxies. In the presence of a bar, the increase in the velocity dispersion σ (within the effective radius) due to the growth of an SMBH is on average ≲ 10%, whereas the increase is only ≲ 4% in an unbarred galaxy. In a barred galaxy, the increase results from a combination of three separate factors: (1) orientation and inclination effects; (2) angular momentum transport by the bar that results in an increase in the central mass density; and (3) an increase in the vertical and radial velocity anisotropy of stars in the vicinity of the SMBH. In contrast, the growth of the SMBH in an unbarred galaxy causes the velocity distribution in the inner part of the nucleus to become less radially anisotropic. The increase in σ following the growth of the SMBH is insensitive to a variation of a factor of 10 in the final mass of the SMBH, showing that it is the growth process rather than the actual SMBH mass that alters bar evolution in a way that increases σ. We argue that using an axisymmetric stellar dynamical modeling code to measure SMBH masses in barred galaxies could result in a slight overestimate of the derived M {sub BH}, especially if a constant M/L ratio is assumed. We conclude that the growth of a black hole in the presence of a bar could result in an increase in σ that is roughly 4%-8% larger than the increase that occurs in an axisymmetric system. While the increase in σ due to SMBH growth in a barred galaxy might partially account for the claimed offset of barred galaxies and pseudo bulges from the M {sub BH}-σ relation obtained for elliptical galaxies and classical bulges in unbarred galaxies, it is inadequate to account for all of the offset.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2022

The High Fraction of Thin Disk Galaxies Continues to Challenge ΛCDM Cosmology

Any viable cosmological framework has to match the observed proportion of early- and late-type galaxies. In this contribution, we focus on the distribution of galaxy morphological types in the standard model of cosmology (Lambda cold dark matter, ΛCDM). Using the latest state-of-the-art cosmological ΛCDM simulations known as Illustris, IllustrisTNG, and EAGLE, we calculate the intrinsic and sky-projected aspect ratio distribution of the stars in subhalos with stellar mass M * > 10 10 M ⊙ at redshift z = 0. There is a significant deficit of intrinsically thin disk galaxies, which however comprise most of the locally observed galaxy population. Consequently, the sky-projected aspect ratio distribution produced by these ΛCDM simulations disagrees with the Galaxy And Mass Assembly (GAMA) survey and Sloan Digital Sky Survey at ≥12.52σ (TNG50-1) and ≥14.82σ (EAGLE50) confidence. The deficit of intrinsically thin galaxies could be due to a much less hierarchical merger-driven build-up of observed galaxies than is given by the ΛCDM framework. It might also arise from the implemented sub-grid models, or from the limited resolution of the above-mentioned hydrodynamical simulations. We estimate that an 8 5 times better mass resolution realization than TNG50-1 would reduce the tension with GAMA to the 5.58σ level. Finally, we show that galaxies with fewer major mergers have a somewhat thinner aspect ratio distribution. Given also the high expected frequency of minor mergers in ΛCDM, the problem may be due to minor mergers. In this case, the angular momentum problem could be alleviated in Milgromian dynamics because of a reduced merger frequency arising from the absence of dynamical friction between extended dark matter halos.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1981

Accuracy and convergence of a finite element algorithm for laminar boundary layer flow

The Galerkin-weighted residuals formulation is employed to derive an implicit finite element solution algorithm for a generally non-linear initial-boundary value problem. Solution accuracy and convergence with discretization refinement are quantized in several error norms, for the non-linear parabolic partial differential equation system governing laminar boundary layer flow, using linear, quadratic and cubic functions. Richardson extrapolation is used to isolate integration truncation error in all norms, and Newton iteration is employed for all equation solutions performed in double-precision. The mathematical theory supporting accuracy and convergence concepts for linear elliptic equations appears extensible to the non-linear equations characteristic of laminar boundary layer flow.

Soliman, M. O.↗

NASA NTRS1990

SIAM Conference on Parallel Processing for Scientific Computing, 4th, Chicago, IL, Dec. 11-13, 1989, Proceedings

Attention is given to such topics as an evaluation of block algorithm variants in LAPACK and presents a large-grain parallel sparse system solver, a multiprocessor method for the solution of the generalized Eigenvalue problem on an interval, and a parallel QR algorithm for iterative subspace methods on the CM2. A discussion of numerical methods includes the topics of asynchronous numerical solutions of PDEs on parallel computers, parallel homotopy curve tracking on a hypercube, and solving Navier-Stokes equations on the Cedar Multi-Cluster system. A section on differential equations includes a discussion of a six-color procedure for the parallel solution of elliptic systems using the finite quadtree structure, data parallel algorithms for the finite element method, and domain decomposition methods in aerodynamics. Topics dealing with massively parallel computing include hypercube vs. 2-dimensional meshes and massively parallel computation of conservation laws. Performance and tools are also discussed.

Dongarra, Jack↗

DOE OSTI2019

A cloud computing approach to massively-parallel distributed stochastic optimization with application to geomechanical reservoir characterization

Many search strategies used to optimize parameters during hydrologic model calibration are inherently limited in that simulations must be performed sequentially in order for the algorithm to converge. As a result, the overall time required to reach a solution increases linearly with the number of steps necessary. In contrast, sampling strategies that attempt to approximate the posterior distribution of the parameters do not require the model simulations to be run in sequence and therefore invite the use of a massively parallel approach across heterogeneous computing environments. We apply a cloud computing methodology to this problem where a head node running on Amazon Web Services continuously produces candidate models that are distributed to arbitrary compute environments to run the simulation, in our case Clemson’s Palmetto cluster computer. Thus the time required to obtain a sufficient number of samples to produce an adequate approximation of the posterior distribution of the parameters is limited by the number of available compute sites. Monte Carlo sampling of the posterior space would be duplicative and inefficient, thus we combine Latin hypercube methods with genetic algorithms to ensure that no large regions of the parameter space are left unexplored, and that high probability regions are investigated thoroughly. We independently assess the fit to different types of data sets without the need to construct a single objective function. Sets of Pareto optimal models are particularly valuable when the quality and information content of data is poorly known or conceptual model errors exist in our simulation. We illustrate our approach for a problem where in situ strain data are used to calibrate the parameters of an oil reservoir in the Avant oil field in Oklahoma. We use well injection and shut-in to stress a deep (500m) confined formation, and observe the geomechanical response using borehole strainmeters installed in the shallow subsurface (30m). These data were then used to calibrate the poroelastic properties of the reservoir and caprock along with the geometry of an elliptic channel associated with the formation. Using our approach we are able to identify issues with model error as well as substantial tradeoffs that occur within the parameters.

inversion, stochastic, geomechanics, poroelastic, ↗

NASA NTRS1987

Relaxation schemes for spectral multigrid methods

The effectiveness of relaxation schemes for solving the systems of algebraic equations which arise from spectral discretizations of elliptic equations is examined. Iterative methods are an attractive alternative to direct methods because Fourier transform techniques enable the discrete matrix-vector products to be computed almost as efficiently as for corresponding but sparse finite difference discretizations. Preconditioning is found to be essential for acceptable rates of convergence. Preconditioners based on second-order finite difference methods are used. A comparison is made of the performance of different relaxation methods on model problems with a variety of conditions specified around the boundary. The investigations show that iterations based on incomplete LU decompositions provide the most efficient methods for solving these algebraic systems.

Phillips, Timothy N.↗