Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Effective stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

The Stability Transition From Stable to Unstable Frictional Slip With Finite Pore Pressure

Pore fluids are ubiquitous throughout the lithosphere and are commonly invoked as the cause of induced seismicity and slow earthquakes. We perform lab experiments to address these questions for drained fault conditions and low pore pressure. We shear simulated faults at effective normal stress (σ' n ) of 20 MPa and pore pressures Pp from 1 to 4 MPa. We document the full range of lab earthquake behaviors from slow slip to elasto-dynamic rupture and show that slow slip can be explained by the slip rate dependence of the critical rheologic stiffness without dilatancy hardening or other fluid effects. Our fault permeabilities ranges from 10 –18 to 10 –17 m 2 with an initial porosity of 0.1 and estimated fluid diffusion time ≈1 s. Slow slip and quasi-dynamic fault motion may arise from high P p at higher pressures but dilatancy strengthening is not a general requirement.

58 GEOSCIENCES↗
NASA NTRS2000

The Effect of Tic Coated Balls and Stress on the Lubricant Lifetime of a Synthetic Hydrocarbon (pennzane 2001A) Using a Vacuum Spiral Orbit Tribometer

A vacuum spiral orbit rolling contact tribometer was used to determine effect of varying mean Hertzian stress (1.0, 1.5, 2.0 GPa) and the use of 440C and TiC coated 440C balls on lubricant lifetime of a synthetic hydrocarbon (Pennzane 2001A) on 440C stainless steel. Conditions included 210 rpm, approx. 50 micrograms lubricant, an initial vacuum < 1.3xl0(exp-6) Pa, and room temperature (approx. 23 C). Increasing the mean Hertzian stress resulted in an exponential decrease in lubricant lifetime for both material combinations. Substituting a TiC coated 440C ball showed no increase in lifetime over the 440C ball. The decreasing lifetime with increasing stress level correlated well with energy dissipation calculations.

Jansen, Mark J.↗
NASA NTRS1974

Stress analysis of the compact specimen including the effects of pin loading

An improved method of boundary collocation was applied to the two-dimensional stress analysis of the compact specimen. The effects of the pin-loaded holes on stress-intensity factors and crack-opening displacements were investigated for various crack-length-to-specimen-width ratios, hole locations, and internal loadings. The stress-intensity factors for the 'standard' compact specimen under plane-stress or plane-strain conditions were found to be within 1 percent of the stress-intensity factors reported in the ASTM Test for Plane-Strain Fracture Toughness of Metallic Materials (E 399-72) over a range of crack-length-to-specimen-width ratios of 0.4 to 0.7. However, for crack-length-to-specimen-width ratios less than 0.4, the pin-load holes (which were not previously accounted for) had a significant effect on stress intensity and crack-opening displacements.

Newman, J. C., Jr.↗
NASA NTRS1985

Design, Fabrication and Testing of an Experimental Apparatus for Determining Particle Behavior Under Very Low Intergranular Stresses

Because the constitutive laws for soils are governed mainly by interparticle friction, all aspects of their mechanical behavior depend strongly on gravitational body forces. This fact poses serious limitations on the formulation of a materially objective soil constitutive theory, based on experimentation performed on Earth. In particular, the presence of the Earth's gravity prohibits the design of controlled experiments to properly simulate a variety of critical phenomena associated with the dynamic response of soils to seismic excitation in a very low effective confining stress field. For these reasons, laboratory-controlled experiments in the Space Shuttle, under essentially zero-gravity conditions, could offer invaluable opportunities for developing a quantitative understanding of fundamental aspects of soil behavior during or after an earthquake, which, in turn, could result in significant technological advances in geotechnical earthquake engineering.

Sture, S.↗
NASA NTRS1979

Development of an Accelerated Test Design for Predicting the Service Life of the Solar Array at Mead, Nebraska

An accelerated life test is described which was developed to predict the life of the 25 kW photovoltaic array installed near Mead, Nebraska. A quantitative model for accelerating testing using multiple environmental stresses was used to develop the test design. The model accounts for the effects of thermal stress by a relation of the Arrhenius form. This relation was then corrected for the effects of nonthermal environmental stresses, such as relative humidity, atmospheric pollutants, and ultraviolet radiation. The correction factors for the nonthermal stresses included temperature-dependent exponents to account for the effects of interactions between thermal and nonthermal stresses on the rate of degradation of power output. The test conditions, measurements, and data analyses for the accelerated tests are presented. Constant-temperature, cyclic-temperature, and UV types of tests are specified, incorporating selected levels of relative humidity and chemical contamination and an imposed forward-bias current and static electric field.

Gaines, G. B.↗
NASA NTRS1975

Growth of surface and corner cracks in beta-processed and mill-annealed Ti-6Al-4V

Empirical stress-intensity expressions were developed to relate the growth of cracks from corner flaws to the growth of cracks from surface flaws. An experimental program using beta-processed Ti-6Al-4V verified these expressions for stress ratios, R greater than or equal to 0. An empirical crack growth-rate expression which included stress-ratio and stress-level effects was also developed. Cracks grew approximately 10 percent faster in transverse-grain material than in longitudinal-grain material and at approximately the same rate in longitudinal-grain mill-annealed Ti-6Al-4V. Specimens having surface and corner cracks and made of longitudinal-grain, beta-processed material were tested with block loads, and increasing the stresses in a block did not significantly change the crack growth rates. Truncation of the basic ascending stress sequence within a block caused more rapid crack growth, whereas both the descending and low-to-high stress sequences slowed crack growth.

Bell, P. D.↗
DOE OSTI2022

Assessment of chemo-mechanical impacts of CO 2 sequestration on the caprock formation in Farnsworth oil field, Texas

This study evaluates the chemo-mechanical influence of injected CO 2 on the Morrow B sandstone reservoir and the upper Morrow shale caprock utilizing data from the inverted 5-spot pattern centered on Well 13-10A within the Farnsworth unit (FWU). This study also seeks to evaluate the integrity of the caprock and the long-term CO 2 storage capability of the FWU. The inverted 5-spot pattern was extracted from the field-scale model and tuned with the available field observed data before the modeling work. Two coupled numerical simulation models were utilized to continue the study. First, a coupled hydro-geochemical model was constructed to simulate the dissolution and precipitation of formation minerals by modeling three intra-aqueous and six mineral reactions. In addition, a coupled hydro-geomechanical model was constructed and employed to study the effects of stress changes on the caprock’s porosity, permeability, and ground displacement. The Mohr–Coulomb circle and failure envelope were used to determine caprock failure. In this work, the CO 2 -WAG injection is followed by the historical field-observed strategy. During the forecasting period, a Water Alternating Gas (WAG) injection ratio of 1:3 was utilized with a baseline bottom-hole pressure constraint of 5500 psi for 20 years. A post-injection period of 1000 years was simulated to monitor the CO 2 plume and its effects on the CO 2 storage reservoir and caprock integrity. The simulation results indicated that the impacts of the geochemical reactions on the porosity of the caprock were insignificant as it experienced a decrease of about 0.0003% at the end of the 1000-year post-injection monitoring. On the other hand, the maximum stress-induced porosity change was about a 1.4% increase, resulting in about 4% in permeability change. It was estimated that about 3.3% of the sequestered CO 2 in the formation interacted with the caprock. Despite these petrophysical property alterations and CO 2 interactions in the caprock, the caprock still maintained its elastic properties and was determined to be far from its failure.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2020

Shock compression of molybdenum single crystals to 110 GPa: Elastic–plastic deformation and crystal anisotropy

To explore the role of crystal anisotropy on the elastic-plastic deformation of BCC single crystals at high shock stresses, molybdenum (Mo) single crystals were shock compressed along [100], [111], and [110] orientations at elastic impact stresses between 20 and 110 GPa. Laser interferometry was used to measure shock wave velocities and particle velocity histories. Along the [100] and [111] orientations, elastic-plastic waves (two wave structure) were observed up to 110 GPa. Along the [110] orientation, the two wave structure was observed only up to 90 GPa. The measured elastic wave amplitudes were analyzed to determine crystal anisotropy effects, impact stress dependence, and the activated slip systems on the Hugoniot elastic limit. The results from our work have provided insight into the role of crystal anisotropy on the elastic-plastic deformation under shock compression at high stresses.

42 ENGINEERING↗
NASA NTRS1973

A study of crack closure in fatigue

Crack closure phenomenon in fatigue was studied by using a Ti-6Al-4V titanium alloy. The occurrence of crack closure was directly measured by an electrical-potential method, and indirectly by load-strain measurement. The experimental results showed that the onset of crack closure depends on both the stress ratio, and the maximum stress intensity factor. No crack closure was observed for stress ratio, greater than 0.3 in this alloy. A two-dimensional elastic model was used to explain the behavior of the recorded load-strain curves. Closure force was estimated by using this model. Yield level stress was found near the crack tip. Based on this estimated closure force, the crack opening displacement was calculated. This result showed that onset of crack closure detected by electrical-potential measurement and crack-opening-displacement measurement is the same. The implications of crack closure on fatigue crack are considered. The experimental results show that crack closure cannot fully account for the effect of stress ratio, on crack growth, and that it cannot be regarded as the sole cause for delay.

Shih, T. T.↗
NASA NTRS1971

Elastohydrodynamic film thickness measurements with advanced ester, fluorocarbon, and polyphenyl ether lubricants to 589 K (600 F)

Elastohydrodynamic (EHD) film thicknesses have been measured, by means of an X-ray technique, under conditions that closely simulate the ball-race contact in advanced turbine engine thrust bearings. The experiments were conducted with a rolling-disk machine using disks which yield a contact zone similar to that in the actual bearing. Both the rolling and spinning motions of the ball relative to the race were simulated by the apparatus. Four lubricants were evaluated at temperatures to 600 F and maximum Hertz stresses to 350,000 psi. The X-ray film thickness data correlated well with observations of surface distress (or lack thereof) in full-scale bearing tests with the same lubricants under similar conditions of temperature and load. The predicted variation of film thickness with speed and viscosity as verified, although the magnitude of measured film thickness was generally one-half to one-third of predicted values. An effect of stress greater than predicted was consistently observed in the higher stress range.

Parker, R. J.↗
NASA NTRS1983

Tensile stress-strain behavior of hybrid composite laminates

A study was made of the stress-strain response of several hybrid laminates, and the damage was correlated with nonlinear stress-strain response and ultimate strength. The fibers used in the laminates were graphite, S-glass, and Kevlar. Some laminates with graphite fibers had perforated Mylar film between plies, which lowered the interlaminar bond strength. The laminate configurations were chosen to be like those of buffer strips in large panels and fracture coupons. Longitudinal and transverse specimens were loaded in tension to failure. Some specimens were radiographed to reveal damage due to edge effects. Stress-strain response is discussed in terms of damage shown by the radiographs. Ultimate strengths are compared with simple failure criteria, one of which account for damage.

Kennedy, J. M.↗
DOE OSTI2024

Nitrogen Vacancy Centers in Diamond for Stress Sensing Applications: Theory and Experiments

Sensing of stress under high elevated environmental conditions with high resolution has critical importance for range of applications including earth’s subsurface scanning and geological CO2 storage monitoring. Using first principles density functional theory (DFT) approach combined with the theoretical modelling of low energy Hamiltonian, here we investigate a novel approach to detect unprecedented level of pressure by taking advantage of solid-state electron’s spin of Nitrogen vacancy (NV) centers in nanodiamond. We computationally explore the effect of strain on the defect band edges and band gaps by varying the lattice parameters of diamond supercell hosting a single NV center. A low energy Hamiltonian is developed that includes effect of stress on the energy level of ±1 spin manifold at the ground state. By quantifying the energy level shift and split, we predict the pressure sensing of up to 0.3 MPa/√Hz. We show superiority of the quantum sensing over traditional optical sensing techniques by discussing our results from DFT and theoretical modelling for the frequency shift per unit pressure. The proposed quantum stress sensing could be useful to measure earth’s subsurface vibrations. Our results open avenues for development of sensing technology with a high sensitivity and resolution under extreme pressure conditions that potentially has a wider applicability than existing pressure sensing technologies.

Paudel, Hari P.↗
NASA NTRS1993

Transverse cracking and stiffness reduction in composite laminates

A study of transverse cracking mechanism in composite laminates is presented using a singular hybrid finite element model. The model provides the global structural response as well as the precise local crack-tip stress fields. An elasticity basis for the problem is established by employing Lekhnitskii's complex variable potentials and method of eigenfunction expansion. Stress singularities associated with the transverse crack are obtained by decomposing the deformation into the symmetric and antisymmetric modes and proper boundary conditions. A singular hybrid element is thereby formulated based on the variational principle of a modified hybrid functional to incorporate local crack singularities. Axial stiffness reduction due to transverse cracking is studied. The results are shown to be in very good agreement with the existing experimental data. Comparison with simple shear lag analysis is also given. The effects of stress intensity factors and strain energy density on the increase of crack density are analyzed. The results reveal that the parameters approach definite limits when crack densities are saturated, an evidence of the existence of characteristic damage state.

Yuan, F. G.↗
DOE OSTI2021

Peak states of molybdenum single crystals shock compressed to high stresses

In this work, to determine crystal anisotropy effects at high stresses, peak states behind the plastic shock waves were examined in BCC single crystals. Using plate impact experiments, molybdenum (Mo) single crystals were shock compressed up to 190 GPa elastic impact stress along [100], [110], and [111] orientations. Laser interferometry was used to measure wave velocities and particle velocity profiles at the Mo–LiF window interface. These data were analyzed to obtain in-material quantities in the peak states. The Hugoniots for [100] and [110] orientations were comparable, but the Hugoniot for the [111] orientation was different from the other two orientations. Also, these Mo single crystal Hugoniots display differences from the polycrystalline Mo Hugoniots. Although none of the differences can be considered large, the present results demonstrate that, unlike FCC metal single crystals (Cu, Al), some anisotropy is preserved in Mo single crystal Hugoniots even at high stresses.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sensing at the Nanoscale Using Nitrogen-Vacancy Centers in Diamond: A Model for a Quantum Pressure Sensor

The sensing of stress under harsh environmental conditions with high resolution has critical importance for a range of applications including earth’s subsurface scanning, geological CO2 storage monitoring, and mineral and resource recovery. Using a first-principles density functional theory (DFT) approach combined with the theoretical modelling of the low-energy Hamiltonian, here, we investigate a novel approach to detect unprecedented levels of pressure by taking advantage of the solid-state electronic spin of nitrogen-vacancy (NV) centers in diamond. We computationally explore the effect of strain on the defect band edges and band gaps by varying the lattice parameters of a diamond supercell hosting a single NV center. A low-energy Hamiltonian is developed that includes the effect of stress on the energy level of a ±1 spin manifold at the ground state. By quantifying the energy level shift and split, we predict pressure sensing of up to 0.3 MPa/Hz using the experimentally measured spin dephasing time. We show the superiority of the quantum sensing approach over traditional optical sensing techniques by discussing our results from DFT and theoretical modelling for the frequency shift per unit pressure. Importantly, we propose a quantum manometer that could be useful to measure earth’s subsurface vibrations as well as for pressure detection and monitoring in high-temperature superconductivity studies and in material sciences. Our results open avenues for the development of a sensing technology with high sensitivity and resolution under extreme pressure limits that potentially has a wider applicability than the existing pressure sensing technologies.

36 MATERIALS SCIENCE↗
NASA NTRS1981

Effect of physical aging on stress relaxation of poly/methyl methacrylate/

A study was made on the stress relaxation behavior at 25 C of poly(methyl methacrylate) in uniaxial tension as a function of physical aging at both room temperature and 60 C. Test specimens were compression molded at 165 C, then quenched to room temperature and allowed to age for up to 30 days prior to testing. Stress relaxation curves measured after different aging times could be superposed to a single master curve for each aging temperature. Superposition was achieved by applying vertical and horizontal shifts. Hence, the shape of the response curves was not changed by aging. This is in accordance with observations made by Struik for tensile creep curves. Volume changes as a function of physical aging were also determined. Simple exponential relationships were observed between volume and both horizontal and vertical shifts. The horizontal shift implies a shift in the effective time scale caused by a change in free volume. The vertical shifts could be correlated with changes in Young's modulus caused by a change in density. For the range of aging studied, the response time scale varied over nearly two decades of log-time. For the same conditions modulus varied by 30 percent.

Cizmecioglu, M.↗
NASA NTRS1978

Flat growth of 7075, 7475, 7050 and 7049 aluminum alloy plate in stress corrosion environments: 2-year marine atmosphere results

Marine atmospheric exposure of smooth and precracked specimens from 7075, 7475, 7050 and 7049 plates support the conclusion that for a given strength level, the short transverse stress corrosion resistance of 7050-T7X and 7049-T7X is superior to that of 7075-T7X. The threshold stress intensity (K sub Iscc) for these alloys is about 25 MPa square root m at a yield strength of about 460 MPa; the corresponding yield strength level for 7075-T7X at this SCR level is about 425 MPa. Additional tests on two lots of high-toughness 7475 plate indicate that this alloy is capable of achieving K sub Iscc values of about 35 MPa square root m at yield strengths of 400-450 MPa. Precracked specimens from all these 7XXX-series alloys are subject to self loading from corrosion product wedging. This effect causes stress corrosion cracks to continue growing at very low apparent stress intensities, and should therefore be considered a potential driving force for stress corrosion in design and materials selection.

Dorward, R. C.↗