Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELONGATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Synthesis, reversibility and mechanism of the dehydration of monoclinic CaZn{sub 2}(PO{sub 4}){sub 2}·2H{sub 2}O

Highlights: • Reversibility of dehydration of synthetic monoclinic CaZn{sub 2}(PO{sub 4}){sub 2}·2H{sub 2}O to CaZn{sub 2}(PO{sub 4}){sub 2}·H{sub 2}O is proven. • Morphological changes upon dehydration to mono- and anhydrate are investigated. • The diffraction pattern of the monohydrate is presented and indexed. • Lattice constants up to the monohydrate are derived from in-situ XRD measurements. • A topotactic dehydration mechanism is deduced. - Abstract: The reversibility of the dehydration of monoclinic CaZn{sub 2}(PO{sub 4}){sub 2}·2H{sub 2}O to the corresponding monohydrate is proven and the dehydration enthalpy determined by combination of thermal analysis and X-ray diffraction. The mechanism of the monohydrate formation is investigated by scanning electron microscopy (SEM) and temperature dependent in situ X-ray powder diffraction. Mechanistic impact on the powder bulk properties are deduced. As for the orthorhombic dimorph, a crystalline monohydrate species is identified and firstly indexed. Thermal induced changes of the lattice parameters up to the formation of the monohydrate are analyzed. A linear elongation of the lattice parallel to the directions [100] and [001] is found. The corresponding elongation coefficients and the volumetric expansion of the unit cell are determined. With regard to the option of synthetic production of the compound, a possible application of the material for thermochemical energy storage and conversion is conceivable. The relevance of fundamental mechanistic features on the bulk behaviour upon cyclic de- and rehydration is discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Computational simulations of [email protected] and [email protected] [email protected] nanotubes

Highlights: • [email protected] nanotubes are easily formed than [email protected] nanotubes. • Armchair [email protected] nanotubes present type-II behavior, while zigzag [email protected] nanotubes present type-I behavior. • The [email protected] had the piezoelectricity response improved until 10% of elongation. - Abstract: The structural, electronic, and mechanical properties of armchair and zigzag chiralities double-walled and [email protected] [email protected] and [email protected] nanotubes were investigated by periodic DFT/B3LYP calculations with an all-electron basis set. For both chiralities, [email protected] presents minor strain and deposition energies, which predict that this nanotube can be easier formed and the GaN is the most favorable substrate (the core) than ZnO. On the other hand, the zigzag [email protected] did not exhibit the major piezoelectric response, which is three times smaller than the [email protected] nanotube, showing that the compression of the [email protected] nanotube length is not favorable to this property. However, the piezoelectricity can be improved when the zigzag [email protected] is under elongation. The elastic constants showed that the [email protected] nanotubes are more rigid than the homogenous nanotubes and present higher piezoelectric constants. In addition, the projected DOS shows that [email protected] has a type-II interface and [email protected] has a type-I interface. Based on the results obtained from our theoretical models, the nanotubes have great potential for the experimental development of new electronic devices.

36 MATERIALS SCIENCE↗

On the role of processing parameters in producing Cu/SiC metal matrix composites via friction stir processing: Investigating microstructure, microhardness, wear and tensile behavior

The main aim of this study is to produce copper reinforced metal matrix composite (MMC) layers using micron sized SiC particles via friction stir processing (FSP) in order to enhance surface mechanical properties. Microstructural evaluation using optical microscopy (OM) and scanning electron microscopy (SEM) indicated that an increase in traverse speed and a decrease in rotational speed cause a reduction in the grain size of stir zone (SZ) for the specimens friction stir processed (FSPed) without SiC particles. With the aim of determining the optimum processing parameters, the effect of traverse speed as the main processing variable on microstructure and microhardness of MMC layers was investigated. Higher traverse speeds resulted in poor dispersion of SiC particles and consequently reduced the microhardness values of MMC layers. It was found that upon addition of SiC particles, wear properties were improved. This behavior was further supported by SEM images of wear surfaces. Results demonstrated that the microcomposite produced by FSP exhibited enhanced wear resistance and higher average friction coefficient in comparison with pure copper. Tensile properties and fracture characteristics of the specimens FSPed with and without SiC particles and pure copper were also evaluated. According to the results, the MMC layer produced by FSP showed lower strength and elongation than pure copper while a remarkable elongation was observed for FSPed specimen without SiC particles. Research Highlights: {yields} Decrease in traverse speed leads to good dispersion of SiC particles in composites. {yields} No distinct TMAZ in side regions of SZ of FSPed specimens with SiC particles. {yields} Microhardness of FSPed specimens with SiC particles shows a remarkable increase. {yields} Reinforcement of Cu with SiC particles improves wear and friction behavior of surface. {yields} A weak bonding in tensile due to probable agglomeration for SiC containing samples.

36 MATERIALS SCIENCE↗

Characterization of adiabatic shear bands in AM60B magnesium alloy under ballistic impact

Adiabatic shear bands in Mg alloy under ballistic impact at a velocity of 0.5 km.s{sup -1} were characterized by means of optical microscope, scanning electron microscope, transmission electron microscope and indenter technique. The results show that adiabatic shear bands were formed around the impacted crater, and the deformed and transformed bands were distinguished by etching colors in metallographic observation. TEM observation shows that the deformed bands were composed of the elongated grains and high density dislocations, while the transformed bands composed of the ultrafine and equiaxed grains were confirmed. In initial stage, the severe localized plastic deformation led to the formation of elongated grains in the deformed bands. With localized strain increasing, the severe localized deformation assisted with the plastic temperature rising led to the severe deformation grains evolved into the ultrafine and equiaxed grains, while the deformed bands were developed into transformed bands. The formation of the ultrafine and equiaxed grains in the transformed bands should be attributed to the twinning-induced rotational dynamic recrystallization mechanism. High microhardness in the bands was obtained because of the strain hardening, grain refining and content concentration. - Research Highlights: {yields} Deformed and transformed bands are found in Mg alloy under ballistic impact. {yields} The microstructures in the deformed and transformed bands are characterized. {yields} The evolution process of the microstructure in the bands is discussed.

36 MATERIALS SCIENCE↗

Microstructure of adiabatic shear bands in Ti6Al4V

Microstructural deformation mechanisms in adiabatic shear bands in Ti6Al4V are studied using traditional TEM and selected area diffraction, and more advanced microstructural characterisation techniques such as energy dispersive X-ray spectroscopy, high angle annular dark field STEM and conical dark field TEM. The shear bands under investigation are induced in Ti6Al4V samples by high strain rate compression of cylindrical and hat-shaped specimens in a split Hopkinson pressure bar setup. Samples from experiments interrupted at different levels of deformation are used to study the evolution of the microstructure in and nearby the shear bands. From the early stages of adiabatic shear band formation, TEM revealed strongly elongated equiaxed grains in the shear band. These band-like grains become narrower towards the centre of the band and start to fraction even further along their elongated direction to finally result in a nano-crystalline region in the core. In fully developed shear bands, twins and a needle-like martensite morphology are observed near the shear band. - Highlights: Black-Right-Pointing-Pointer CDF can resolve the nanostructure of an ASB. Black-Right-Pointing-Pointer Nanometre-sized grains well below 100 nm are present in the shear band. Black-Right-Pointing-Pointer Highly fractioned regions inside ASB contain both {alpha} and {beta} phases. Black-Right-Pointing-Pointer Strong deformation yields {alpha} twins and martensite morphology. Black-Right-Pointing-Pointer The microstructure of the ASB in both samples is similar.

36 MATERIALS SCIENCE↗

Characterization of bulk stainless steel joints developed through microwave hybrid heating

Processing of metallic materials through microwave heating is a challenging area of research. In the present work, joining of stainless steel-316 to stainless steel-316 in the bulk form has been carried out by placing stainless steel-316 powder at the interface and through targeted heating using microwave hybrid heating. The trials were carried out in a multimode microwave applicator at a frequency of 2.45 GHz and power 900 W. The developed joints were characterized using X-ray diffraction, field emission scanning electron microscopy equipped with energy dispersive X-ray spectroscope and measurement of Vicker's microhardness, porosity and tensile strength. The X-ray diffraction spectrum of the developed joint shows the presence of chromium carbide, iron carbide and iron silicide phases that eventually contribute to enhancement of the microhardness of the joint. The scanning electron microscope micrographs confirm classical metallurgical bonding between the substrate and the interface (molten powder) layer; the epitaxial growth rate was observed adjacent to the fusion zone. The average observed Vicker's microhardness in the joint zone on the grain boundary was significantly higher than that inside the grains due to the presence of various hard phases at the grain boundaries. Evaluation of the tensile strength of the joints showed an average ultimate tensile strength of 425.0 MPa with an average elongation of 9.44%. - Highlights: • Joining of stainless steel (SS-316) plates using microwave hybrid heating • Epitaxial growth rate observed adjacent to the fusion zone of welded joint • The ultimate tensile strength of the order of 425.0 MPa with 9.44% elongation.

36 MATERIALS SCIENCE↗

Microstructural evolution and micromechanical properties of gamma-irradiated Au ball bonds

The effect of gamma radiation on the mechanical and structural properties of gold ball bonds was investigated. Gold wires from thermosonic wire bonding were exposed to gamma rays from a Cobalt-60 source at a low dose (5 Gy). The load–depth curve of nanoindentation for the irradiated gold wire bond has an apparent staircase shape during loading compared to the as-received sample. The hardness of the specimens calculated from the nanoindentation shows an increase in value from 0.91 to 1.09 GPa for specimens after exposure. The reduced elastic modulus for irradiated specimens significantly increased as well, with values from 75.18 to 98.55 GPa. The change in intrinsic properties due to gamma radiation was investigated using dual-focused ion beam and high-resolution transmission electron microscope analysis. The dual-focused ion beam and high-resolution transmission electron microscope images confirmed the changes in grain structure and the presence of dislocations. The scanning electron microscope micrographs of focused ion beam cross sections showed that the grain structure of the gold became elongated and smaller after exposure to gamma rays. Meanwhile, high-resolution transmission electron microscopy provided evidence that gamma radiation induced dislocation of the atomic arrangement. - Highlights: • Nanoindentation technique provides a detailed characterisation of Au ball bond. • P–h curve of irradiated Au ball bond shows an apparent pop-in event. • Hardness and reduced modulus increased after exposure. • Elongated and smaller grain structure in irradiated specimens • Prevalent presence of dislocations in the atomic arrangement.

36 MATERIALS SCIENCE↗

Microstructure evolution of 7050 Al alloy during age-forming

The microstructure evolution of the 7050 Al alloy treated by age-forming was studied using a designed device which can simulate the age-forming process. The grain shape, grain boundary misorientation and grain orientation evolution of 7050 Al alloy during age-forming have been quantitatively characterized by electron backscattering diffraction technique. The results show that age-forming produced abundant low-angle boundaries and elongated grains, which attributed to stress induced dislocation movement and grain boundary migration during the age-forming process. On the other side, the stress along rolling direction caused some unstable orientation grains to rotate towards the Brass and S orientations during the age-forming process. Hence, the intensity of the rolling texture orientation in age-formed samples is enhanced. But this effect decays gradually with increasing aging time, since stress decreases and precipitation hardening occurs during the age-forming process. - Highlights: • Quantitative analysis of grain evolution of 7050 Al alloys during age-forming • Stress induces some grain rotation of 7050 Al alloys during age-forming. • Creep leads to elongate grain of 7050 Al alloys during age-forming. • Obtains a trend on texture evolution during age-forming applied stress.

36 MATERIALS SCIENCE↗

Evolution of twinning in extruded AZ31 alloy with bimodal grain structure

Twinning in extruded AZ31 alloy with a bimodal grain structure is studied under compression along the extrusion direction. This study has combined in-situ measurements during the compression tests by Synchrotron Radiation Diffraction and Acoustic Emission techniques and the evaluation of the microstructure and texture in post-mortem compression samples deformed at different strains. The microstructure of the alloy is characterized by the coexistence of large areas of fine dynamic recrystallized grains and coarse non-recrystallized grains elongated along extrusion direction. Twinning occurs initially in large elongated grains before the macroscopic yield stress which is controlled by the twinning in equiaxed dynamically recrystallized grains. - Highlights: • The AZ31 extruded at low temperature exhibits a bimodal grains structure. • Twinning takes place before macroscopic yielding in coarse non-DRXed grains. • DRXed grains controls the beginning of plasticity in magnesium alloys with bimodal grain structure.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of extruded Mg-Gd-Y-Zn-Zr alloys filled with intragranular LPSO phases

Highlights: • Intragranular thin-platelet LPSO phases strongly restrict the DRX. • The low extrusion ratio fails to widely break the intragranular LPSO. • The large extrusion ratio results in the full DRX via the CDRX mechanism. • Finer DRX-ed grains and LPSO induce the higher yield strength and elongation. • The larger grain size causes an increase in the strain hardening rate. - Abstract: A comparison has been made on the dynamic recrystallization (DRX), texture, and mechanical properties of the Mg-5.5Gd-4.4Y-1.1Zn-0.5Zr (wt%) alloys extruded with different ratios (ER, 36 and 7.1). Intragranular long-period stacking ordered (LPSO) phases strongly restrict the DRX by restraining the lattice rotation of α-Mg grains and hindering the migration of the boundaries of DRX-ed grains. Extrusion with ER of 36 can widely break the intragranular LPSO phases and create a fully DRX-ed microstructure with a relatively random texture, while the lower ER of 7.1 fails to break the LPSO and leads to a bimodal microstructure with a strong basal fiber texture. Finer DRX-ed grains and smaller LPSO phases account for the superior tensile yield strength and elongation of the ER36 alloy. However, the ultimate tensile strength of the ER7.1 alloy catches up because its larger grain size causes an increase in the strain hardening rate.

36 MATERIALS SCIENCE↗

Effects of the rolling temperature on microstructure and mechanical properties of 2Cr13/316L laminated composites prepared by accumulative roll-bonding (ARB)

Highlights: • The rolling temperature affects the grain size and microstructural phases of the composite plates. • The rolling temperature affects tensile strength and bending strength of 2Cr13/316L properties of the composite plates. • The temperature gradient and thermal deformation of center and outside regions are different during rolling process. • Composite plate with higher strength and elongation can be obtained by rolling processes. - Abstract: The microstructure and mechanical properties of 2Cr13/316L composite plates by hot-rolling at different rolling temperatures of 1130 °C, 1180 °C, 1250 °C, 1300 °C are investigated in details. With the increase of the rolling temperature, the tensile strength and bending strength of 2Cr13/316Lwere reduced first and then increased slightly due to the coarsening of grains and the increasing of ferrite content in 2Cr13 layers. The highest tensile elongation is obtained at the composite plate with rolling temperature of 1180 °C. 2Cr13/316L composite plates obtained by hot rolling processes were able to withstand larger bending deformation, and no cracks or interfacial delamination can be found in the bending process because of a strong combined interface.

36 MATERIALS SCIENCE↗

Creep-induced microstructural evolution in a nickel-based superalloy designed for advanced ultra-supercritical boilers

Highlights: • Microstructural evolution of a nickel-based superalloy during long-term creep was investigated. • Precipitate-free zones (PFZs) widely arose near the grain boundary under stress. • The coarsened and elongated particles in the PFZs were identified as γ′ precipitates. • The boundary movement plays a role in evolution of grain boundary precipitates. - Abstract: Long-term microstructural stability is a major concern for candidate materials used in advanced ultra-supercritical (A-USC) power plants. In the present work, precipitation behavior of a nickel based superalloy designed for A-USC boilers, with a base composition of Ni-25Cr-20Co, was investigated during long-term thermal exposure under different stresses at 1043 K. The results showed that the coarsening of γ′ precipitates in the grain interior had occurred during thermal exposure in the presence and absence of stress. The microstructure around grain boundary was altered remarkably under stress. The precipitate-free zones (PFZs) commonly existed near the grain boundary in the gauge sections of specimens after long-term creep. Coarsened and elongated particles in the PFZs were identified as γ′-Ni{sub 3} (Ti, Al) precipitates by chemical composition analysis and diffraction pattern. Furthermore, the morphology and distribution of MC-type carbides have no significant changes observed due to their good stability, but discontinuous M{sub 23}C{sub 6} appeared under stress, due to formation of PFZs resulting in dissolution of the adjacent M{sub 23}C{sub 6}. Besides, the creep-rupture mechanism was discussed to explore a potential approach for improving creep properties.

36 MATERIALS SCIENCE↗

Growth behavior and orientation relationships in AISI 304 stainless steel during directional solidification

Highlights: • N–W orientation relationship between the lathy ferrite and austenite was determined. • {103} and <001> of ferrite are parallel to the sample surface and heat flow direction. • Lathy ferrite is elongated in [001], [011], and [123] directions during solidification. - Abstract: The formation mechanism of lathy ferrite in AISI 304 stainless steel during directional solidification was discussed in terms of the orientation relationship between ferrite and austenite. Experimental results show that most of the ferrite laths are arranged parallel and a few ferrite laths with perpendicular morphology can also be observed in the solidified microstructure. Selected-area diffraction patterns by transmission electron microscopy (TEM) and pole figures by electron backscatter diffraction (EBSD) show that Nishiyama–Wassermann orientation relationship between the lathy ferrite and austenite exists in the solidified microstructure. Based on the pole figures of the ferrite, it was found that (103) and [001] of the lathy ferrite are parallel to the sample surface and heat flow direction, respectively, during directional solidification. The elongated directions of the lathy ferrite are found to be [001], [011], and [123], which means that the lathy ferrite grows without preferential direction during directional solidification.

36 MATERIALS SCIENCE↗

Microband induced plasticity and the temperature dependence of the mechanical properties of a carbon-doped FeNiMnAlCr high entropy alloy

Highlights: • A superior fcc HEA with the strength of 1.5 GPa at the cryogenic condition is developed. • The strengthening mechanisms of HEAs at different temperatures are clarified. • The temperature dependence of MBIP effect is revealed. - Abstract: The uniaxial mechanical properties of the high entropy alloy (HEA) Fe{sub 40.4}Ni{sub 11.3}Mn{sub 34.8}Al{sub 7.5}Cr{sub 6} doped with 1.1 at.% C have been determined for both the as-cast and recrystallized states at temperatures from 77 to 973 K. Very high yield strengths were obtained at 77 K of 928 MPa for the as-cast HEA and 1037 MPa for the recrystallized HEA. The yield strength decreased sharply to 293 K and more slowly to 973 K, where it was ~200 MPa [11] in both conditions. The lattice friction stress, which results from the increase of the Peierls barrier, was the major contributor to the large yield strength at 77 K. On the other hand, the grain boundaries lose their strengthening ability at a high temperature, which largely accounts for the sharp drop in yield strength of the fine-grained (5 μm) recrystallized HEA at 973 K. The elongation to failure was highest at 293 K and 673 K with the lowest values at 77 K. Transmission electron microscopy was used to study the effects of temperature on the deformation mechanisms of the HEAs, especially the temperature dependence of the microband-induced plasticity effect. At temperatures ranging from 77 K to 673 K microbands form in the as-cast HEA, while dislocation clusters were observed in the recrystallized HEA over this temperature range. Only tangled dislocations were found at 973 K for both the as-cast and recrystallized HEA due to thermally-activated deformation.

36 MATERIALS SCIENCE↗

Microstructural analysis of undoped and moderately Sc-doped TiO2 anatase nanoparticles using Scherrer equation and Debye function analysis

Highlights: • UV light sensitive undoped and moderate Sc-doped anatase nanocrystallites were prepared without post-synthesis annealing. • Elongated nanocrystallites were found by Scherrer equation and Debye Function Analysis applied to XRD data and also HRTEM. • 4 at.% Sc doping reduced the amount of Ti vacancies by half. • Doping showed ~0.3% growth of lattice parameters. - Abstract: UV light sensitive undoped and moderate (4 at.%) Sc-doped anatase nanocrystallites were prepared by an efficient and environmentally benign method based on homogeneous hydrolysis of TiOSO{sub 4} and Sc{sub 2}(C{sub 2}O{sub 4}){sub 3.5}H{sub 2}O aqueous solutions using urea as a precipitation agent, without post-synthesis calcination or annealing. X-ray diffraction study of the obtained powders revealed single phase anatase in both samples. Two different methods were applied to estimate the anatase crystallite size and shape from the X-ray diffraction data. The first one is based on the more conventional Scherrer equation (as implanted in GSAS-II program) while the second one is based on Debye function analysis (as implanted in DUBUSSY suite version 2.2), which is considered to be more adequate for nanocrystallites. Although each program has its own shape models, both methods indicated similar results of elongated nanocrystallite geometry for Sc-doped TiO{sub 2}: (i) GSAS-II confirmed ellipsoid shape with equatorial size of 5.1(0) nm and axial size of 6.8(0), (ii) DEBUSSY suite 2.2 showed cylinder shape with diameter of equivalent circle in the ab-plane, D{sub ab} = 4.9(1.0) nm and crystallite length along the c-axis, L{sub c} = 5.4(3.2) nm. For the undoped TiO{sub 2} sample, equatorial size of 5.5(0) nm and axial size of 7.3(0) nm for the ellipsoid shape was determined according to GSAS-II, while D{sub ab} = 5.5(1.3) nm and L{sub c} = 6.0(2.2) nm for the cylinder shape was determined by DEBUSSY suite 2.2. These outcomes were found to corroborate with HRTEM analysis. Doping with 4 at.% Sc caused ~0.3% growth of lattice parameters from a = 3.7979 [4] Å, c = 9.4995 [9] Å for the undoped sample to a = 3.8110 [7] Å, c = 9.5274 [16] Å for the moderately Sc doped sample, while reduction in the Ti vacancies by half was confirmed by both methods. The introducing of Sc as electronically active secondary species into the crystal lattice of TiO{sub 2} can greatly alter its optical absorption. The incorporation of Sc into the crystal lattice of TiO{sub 2} favors the substitution of Ti, as both have approximately the same ionic size, and generates surface oxygen vacancies which can act as trapping center for the photogenerated electrons and reduce the recombination of electron–hole pairs. We can expect Sc doped TiO{sub 2} nanomaterials to have applications as effective photocatalysts for selective photocatalytic oxidation of various environmental organic pollutants.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Work hardening behavior and tensile properties of a high-Mn damping steel at elevated temperatures

Highlights: • Stability of austenite and ε-martensite was varied by changing the temperature of deformation. • Work hardening behavior was affected by the effects of TRIP, TWIP, DSA and dislocation slip. • Ultimate elongation was significantly decreased when ε → α′ transformation was too hard to occur. - Abstract: An austenite/ε-martensite dual-phase high-Mn damping steel was tensile deformed at elevated temperatures to conduct a comprehensive study about the effects of transformation-induced plasticity (TRIP), twinning-induced plasticity (TWIP), dynamic strain aging (DSA) and dislocation slip (DS) on its work hardening behavior and tensile properties. The results showed that the work hardening behavior of high-Mn damping steel can be divided into two stages. In stage-I, the main factor influencing the work hardening changed from γ → ε transformation to DS as the deformation temperature was increased. In the second stage, the work hardening exponent and ultimate tensile strength were large when intense DSA occurred at 80 °C and 120 °C, although ε → α′ transformation became more difficult at elevated temperatures. Tensile deformation at 200 °C promoted ε → γ transformation, such that the work hardening exponent and ultimate elongation were significantly decreased. In the later stage of deformation at 260 °C, TWIP effect effectively enhanced the work hardening as deformation-induced ε → α′ transformation occurred at low deformation temperatures.

36 MATERIALS SCIENCE↗

Effect of microstructures on hot compression behavior of a Ti-43Al-2Si alloy fabricated by cold crucible continuous casting

Highlights: • TiAl alloys with different lamellar colonies were fabricated by cold crucible continuous casting. • EBSD was used to investigate the evolution of lamellae during the hot compression. • Lamellar colony boundaries promote the dynamic recrystallization process. - Abstract: To investigate the influence of lamellar orientation and colony boundary on deformation behavior, fully lamellar Ti-43Al-2Si alloys were prepared by cold crucible continuous casting and isothermal compression tests were conducted at different temperatures in the range 1373–1523 K with a strain rate of 0.01 s{sup −1}. The as-cast microstructures were elongated colony with lamellae oriented at nearly 45° to the compression direction and equiaxed colony with various lamellae orientations, respectively. The results revealed that serious cracking or sliding traces appeared on the surface of deformed specimens with elongated colony original microstructure and that their peak stresses were lower compared to those of specimens with equiaxed colony original microstructure. The relationship between deformation behaviors and as-cast microstructure was analyzed in detail. It was found that the recrystallization/globularization level is significantly lower than that in specimens with equiaxed colony original microstructure during hot deformation owing to the preferred nucleation sites in colony boundaries. Finally, the lamellae conversion process was characterized to reveal the softening mechanisms of full lamellar TiAl-based alloy during hot compression.

36 MATERIALS SCIENCE↗

Variation improvement of mechanical properties of Mg-9Al-1Zn alloy with melt conditioned high pressure die casting

Highlights: • The variation improvement of mechanical properties of AZ91D was achieved via application of high shear melt conditioning. • The elongation variation of AZ91D with MC-HPDC has a significant reduction from 31.2% for tradition HPDC to 19.7%. • High shear melt conditioning can result in grain refinement of primary α-Mg formed in both shot sleeve and die cavity. - Abstract: Melt conditioning treatment via high shearing on Mg-9Al-1Zn melt was employed to disperse the oxide inclusions, and to harness the well-dispersed particles as the effective heterogeneous nucleation sites for primary α-Mg grains during solidification in high pressure die casting. To reveal the mechanism of property improvement, Prefil pressure filtration cleanliness analyzer, field-emission scanning electron microscopy with energy dispersive X-ray spectroscopy and high-resolution transmission electron microscopy were employed in present study. The experimental results showed that the application of high shearing not only improved elongation, ultimate tensile strength and yield strength simultaneously, but also reduced the variation of the mechanical properties of Mg-9Al-1Zn alloy. The improvement was ascribed to the refinement of the primary α-Mg grains formed in both shot sleeve and die cavity, and to the reduction of porosity as well as refinement of Mg{sub 17}Al{sub 12} phases.

36 MATERIALS SCIENCE↗