Results for “Cryocooler” — Page 39

NASA NTRS2023

Concepts for the Liquefaction of Hydrogen for In-Situ Operations on the Lunar or Martian Surface

While oxygen will probably be the first fluid liquefied from in-situ developed propellants, hydrogen will also be a sought-after commodity on both the Lunar and Martian surfaces. General hydrogen liquefaction processes are not significantly affected by the atmosphere on Mars and similar processes can be applied on both surfaces. However, hydrogen will require different processes than oxygen (which can be directly liquefied into its final use tank) due to the different spin states the hydrogen nucleus (i.e. parahydrogen and orthohydrogen) can have as well as the significant sensible energy that has to be removed prior to the actual phase change. Due to the low efficiency of 20 K class cryocoolers and high sensible heat removal requirements at higher temperatures, significant benefits can be obtained by precooling the hydrogen gas in a variety of manners. The benefits of three concepts are explored to take advantage of different precooling technics as well as accounting for sensible, latent, and para to ortho conversion heating requirements. Process concepts are shown that can reduce the base input power requirements for heat removal by more than 67% and the radiator area by similar amounts. A majority of the technology development for these processes has already begun, both within NASA and externally, with the few gaps being identified.

ISRU↗

NASA NTRSDate not supplied

Kiloton Class ISRU Systems for LO2/LCH4 Propellant Production on the Mars Surface

As part of the 2023 strategic analysis cycle to explore the trade space, the NASA Mars Architecture Team wanted to explore what it takes to produce in situ on Mars many hundreds of tons of propellants for a large all-chemical transportation system. The conceptual operations and design of the LO 2 /LCH 4 in situ resource utilization (ISRU) water acquisition, propellant production and liquification system was assigned to the NASA Compass concurrent engineering team with support from various NASA ISRU, cryogenic fluid management, and surface power experts. The conceptual point design examined one case producing 300 t of LO 2 /LCH 4 from the Mars atmosphere and delivered water in 20 months and storing the liquified propellants in a to-be-reused lander. Several of these large single-stage, all-chemical class large vertical landers would deliver the required ISRU equipment. The required 150 t of water stock for the ISRU system was traded between three options: delivered, pumped from subsurface ice deposits or extracted from surface soils. The large propellant production systems consist of atmospheric CO 2 collection scroll pumps, a combined solid oxide electrolysis and methanation system to convert the CO 2 and water into gaseous O 2 and CH 4 , and various dryers, scrubbers, and separators to remove the excess water, CO 2 and H 2 . The liquefaction system consisted of 90 K cryocoolers to provide cold Ne to the launch vehicle tanks to liquify these CH 4 and O 2 gases and store them as rocket propellants. The systems are deployed using a 6 t (payload) capable chassis derived from conceptual pressurized rover designs. In total, the propellant production and liquefaction systems required three propellant production pallets, two liquefaction pallets, two water tankers, and six 40 kW-fission surface power systems (FSPS) with cabling. All this equipment was found to notionally fit inside two- 75 metric ton payload capacity Mars ascent and landing vehicles (MALV). For the case where 150 t of water delivered from Earth, four cargo MALVs are required for the full system. The same is true when the 150 t of water is extracted through surface mining. For the borehole system, only 3 cargo MALVs are necessary. A comparison of approaches in terms of number of landers, number and type of elements, power and time is made.

ISRU↗

NASA NTRSDate not supplied

Long Duration Storage of Liquid Hydrogen via Two-Stage Active Cooling Hardware Characterization and Test Planning

The zero boil-off storage of liquid hydrogen using active cooling (cryocoolers) with a two-stage cooling approach is being investigated by NASA. In interest of advancing the technology to enable extended duration storage for the agency’s future long duration missions, NASA’s Technology Demonstration Mission Program has funded this five-year effort which includes the design, build and testing of a test article to demonstrate this concept. This paper includes discussions of the multiple Cryogenic Fluid Management technologies that were studied under NASA’s Cryogenic Propellant Storage and Transfer project, design of the test article to be demonstrated, then the planned test objectives which include characterization testing of the active cooling system, demonstration of the control system, preliminary testing with liquid nitrogen, and a complete demonstration of zero boil-off storage of liquid hydrogen. The full demonstration will be conducted in the East Test Area at NASA Marshall Space Flight Center and is currently scheduled to begin on October 1st, 2024.

Cryogenic Fluid Management↗

NASA NTRS2024

Solid-State Thermodynamic Vent System (STVS) for Control of Cryogenic Propellants

A Solid-State Thermodynamic Vent System (STVS) is a novel Cryogenic Fluid Management (CFM) technology for spacecraft cryogenic propellant tanks that may reduce boiloff while providing greater control over the propellant condition. By exploiting the vacuum-induced cryocooling (VIC) potential of cryogen-saturated silica aerogel material, an internal STVS heat exchanger (HX) can expel some sacrificial cryogenic propellant to the vacuum of space to produce cooling within the storage tank. This cooling is transferred directly to the stored fluid, thereby reducing boiloff and increasing hold times. Testing proved the effectiveness of the concept by reducing the liquid nitrogen (LN 2 ) boiloff rate and tank pressure by roughly 70% and 77%, respectively, during a single pump-down cycle, which sacrificed around 1.8 kg of propellant.

Cryogenic Fluid↗

NASA NTRS2024

x Thermal Straps

Thermal straps, also known as heat straps or flexible conductive links, offer design solutions for enhancing the thermal bond of two items that may need to be mechanically decoupled. The need for mechanical decoupling can be driven by requirements for things like vibration or load isolation, or simply by packaging constraints. A few examples include thermal straps used to mechanically isolate delicate spaceborne detectors from cryocooler vibrations, or thermal straps coupling a high-dissipation electronic component to a heat sink on an adjacent surface in a volume optimized electronics unit.

thermal, heat transfer, straps↗

NASA NTRSDate not supplied

Concept Design of a 5 MW Axial Flux Partially Superconducting Electric Machine

Single aisle class and larger electric and hybrid electric airplanes require high performance electric machines with power levels greater than 1 MW. Partially superconducting machines with superconducting rotors cooled by cryocoolers and no-cryogenic stators are one possible solution for meeting the machine performance requirements at these power levels. In this paper, a conceptual design for a double-stator single-rotor axial-flux partially superconducting machine is presented. A design tool for the topology is presented and used to generate an initial concept design. High fidelity analysis of the concept design is used to access the feasibility of the concept design to meet its target performance metrics and find areas of refinement for the next iteration of the design tool and the design.

Thomas Tallerico↗

NASA NTRSDate not supplied

Evaluating Lunar Water Processing System Model Configurations for Small Scale Oxygen and Hydrogen Production Within JAXA'S ISRU Technology

Introduction: In-Situ Resource Utilization (ISRU) refers to novel methods of extracting and processing local resources for use in life support and propulsion systems, reducing or eliminating the required consumables to be transferred from Earth. Current estimates of water-ice availability embedded in regolith within the Moon’s permanently shadowed regions (PSR’s) range between 1-5% by weight. However, the composition and characteristics of the “wet” regolith is unknown. Alternate ISRU excavation techniques and Concept of Operations (ConOps) must be explored to optimize surface system operations based on these factors. To assess the feasibility of different ISRU subsystem technologies and compare system architecture configurations, an interchangeable system model was generated to incorporate technologies spanning excavation of raw materials to storage of products and determine optimal arrangement of total system processing needs. Total Mass, Volume, and Power (M/V/P) requirements were computed for 168 design iterations of this water processing plant. System Model: In FY24, the System Engineering and Integration (SE&I) ISRU Modeling and Analysis (SIMA) team developed a lunar water processing system model using the Mission Analysis and Integration Tool (MAIT) to estimate the M/V/P for ISRU subsystems operating under a wide range of Hydrogen (H2) and Oxygen (O2) production targets for the Space Technology Mission Directorate (STMD) [1]. Based on Japan Aerospace Exploration Agency’s (JAXA) surface operational requirements, this system architecture was modified to include the ability to excavate consolidated icy regolith (versus granular ice excavation using Kennedy Space Center’s (KSC) ISRU Pilot Excavator, IPEx) and explore the feasibility of processing the lunar water both inside and outside of the PSR. For the consolidated icy regolith case study, excavation was performed via a mobility transport chassis outfitted with The Regolith Ice Drill for Exploring New Terrain (TRIDENT) for drilling [2] and the Cold Operable Lunar Deployable Arm (COLDArm) [3] for regolith transfer. The system model determines the required rover and payload. M/V/P to handle the required regolith processing rates. The regolith is then sorted and heated to sublimate the ice (via an auger dryer). The exiting high temperature, low pressure vapor is cleaned of volatiles (via cold trap) and electrolyzed to produce H2 and O2. These products are then dried, liquified with 20 K and 90 K cryocoolers (for H2 and O2, respectively), and stored in cylindrical tanks. Study Goals: Due to the different ConOps options of regolith transport to the ridge for processing versus processing it directly inside the PSR, as well as the unknown regolith/water-ice composition, new excavation techniques and their power configurations are being evaluated within a ISRU system architecture for production targets less than NASA’s pilot plant (1 mT). This analysis investigates the feasibility of numerous excavation techniques, power architectures, and logistical operations and determines an optimal system configuration with regards to M/V/P. It aims to investigate which parameters, both locally and globally, have the greatest effect on each subsystem within the plant. This can be used to identify the most critical components of the plant, and guide future decisions on allocating funding for research and development. The results from this study may provide subsystem developers with appropriate interfaces with excavation subsystems and downstream processes, and assessing the overall feasibility of each excavation technique, power architecture, and logistical timeframe. References: [1] Carlson, A. et. al. (2024) ICES. [2] Zacny, K., et. al. (2024) “ASCE Earth and Space”. [3] McCormick, R., et. Al. (2024) IEEE Xplore.

ISRU↗

NASA NTRSDate not supplied

System Modeling of a Lunar Molten Regolith Electrolysis Plant

Introduction: In-Situ Resource Utilization (ISRU) is the process of extracting local resources to produce commodities for propulsion, life support systems, and off-planet construction rather than transporting consumables from Earth. Molten Regolith Electrolysis (MRE) is a novel ISRU method of extracting oxygen gas and metal alloy from lunar regolith. The MRE process involves placing lunar regolith between two electrodes, through which current is passed, to melt the regolith and reduce the metal oxide constituents by direct electrolysis (e.g. FeO, SiO2, MgO, Al2O3) into oxygen gas and metal alloys. The oxygen is liquefied and used as propellant for landers, while the metals (e.g. Ferro-alloys) are further processed and used in structural building materials and parts manufacturing. A system model was developed that accounted for the major processes of an MRE plant (from excavation of raw materials to storage of products) to assess the feasibility of a lunar MRE plant. The System Engineering and Integration (SE&I) ISRU Modeling and Analysis (SIMA) team utilized its previously documented system sizing model, the Mission Analysis and Integration Tool (MAIT) [1] as framework of the system model. MAIT uses MATLAB/Simulink to integrate subsystem models into a complete system model of the MRE plant. Total mass, volume, and power requirements were computed for numerous iterations of a MRE plant. System Model: Figure 1: MRE Plant Block Diagram The regolith excavation model determines the mass and power needed to excavate sufficient regolith. The preheating auger initiates the regolith heating process before regolith enters the MRE re-actor to reduce the energy required to turn the solid into a molten liquid. The MRE reactor is modeled in COMSOL Multiphysics and based on the research by Dominguez, Sibille, and Schreiner [2, 3, 4]. This preliminary reactor model provides an accurate calculation of thermal equilibrium during electrochemical operation of the reactor system to assess the optimal mass and power required to process the inlet flow of regolith. The model also computes the outlet flowrates of oxygen and molten products. For this analysis, the primary components of the metal alloy considered were iron and silicon. The oxygen is then purified using an Yttrium Stabilized Zirconia (YSZ) electrode, followed by liquefaction using a 90K cryocooler to be stored as liquid oxygen in insulated cylindrical tanks. In future iterations of the system model, the molten metal tapped from the MRE reactor will undergo additional processing or refinement. However, downstream handling of metals is currently a technology gap that is missing a high TRL subsystem model. Therefore, for this analysis, the accumulated metal alloy stream terminates after leaving the MRE reactor. Study Goals: This analysis investigates multiple input variables to the system to determine the sensitivity of a (near) complete plant at full-scale. This preliminary investigation ran parametric sweeps on the MRE reactor geometry, electrical current supply, layers of multi-layer insulation (MLI) on the reactor, size of the electrodes in the oxygen purification model, and regolith composition (based on landing site location). Three production targets of oxygen (1,000, 10,000, and 50,000 kg/yr) were investigated for this analysis. The parametric sweeps conducted in this analysis provide valuable insight into the expected impact of the various model inputs on plant size. This information can be used to identify the most critical components of the plant and guide future decisions on allocating funding for research and development, providing subsystem developers with appropriate interfaces with downstream and upstream processes, and assessing the overall feasibility of MRE when compared to other ISRU plants. References: [1] Carlson, A. et al. (2024) ICES, ICES-2024-53. [2] Dominguez, D.A., and Sibille, L. (2011) AIAA, AIAA-2011-700. [3] Schreiner, S.S. (2015) MIT, Dissertation. [4] Schreiner, S.S. et al. (2016) ASR, 57(7), pp.1585-1603.

ISRU↗

NASA NTRSDate not supplied

Effect of Engine Thrust and Isp Tradeoffs and Alternate Propellants on ΔV Budget and Architecture Mass for 1st Generation Nuclear Thermal Propulsion Flight Test Systems

Following the first Nuclear Thermal Propulsion (NTP) system test, also known as DRACO, the next NTP system to be developed would be the 1st Generation NTP system. An analysis was conducted to determine the performance of different vehicle configurations utilizing hydrogen (H-NTP), ammonia (A-NTP), and methane (M-NTP) as propellants launched onboard commercial launch vehicles. This was enabled by a quasi-steady-state power balance engine model and vehicle component physics that sized the vehicle system using Master Equipment List (MEL) parameters. The analysis considered configuration cases outlined by a matrix of different mission classes and vehicle configurations that covered the design space of the 1st Generation NTP system to explore various propellant options, engine architectures, and mission scopes. Four mission classes were evaluated which included single burn missions performing maneuvers having a ΔV of 1 km/s and 2.5 km/s followed by 2-burn and 4-burn missions that aimed to exhaust the launch vehicles volume or mass limitations. In all cases, the NTP systems with the lowest thrust class had the longest burn time of which A-NTP and M-NTP systems provided the longest and shortest burn times depending on the launch vehicle used while H-NTP systems tended to cluster together in the middle. Longer burn times could be useful as a testing platform to increase the time for data accumulation. Across the multi-burn cases, H-NTP systems were found to be volume limited while A-NTP and M-NTP systems were mass limited. Both single burn missions showed that A-NTP configurations provided the lowest dry mass given that ammonia had the highest density with comparable performance to M-NTP systems and no requirement for cryocoolers. The results showed that beyond the propellant selection type, the launch vehicle selection, which included Starship, New Glenn, Vulcan, Falcon 9 (recoverable), and Falcon Heavy (recoverable), was a primary driving factor in the test vehicle’s capabilities. Trends were determined based on a set of dimensionless parameters that included the mass ratio of inert mass to initial wetted mass, ratio of specific impulse to burn time, and a dimensionless engine parameter (ratio of impulse to engine momentum). These relationships found the “knees-in-the-curves” that could be a significant point of reference for the designer as they indicate a change in the trend which is located at a specific impulse to burn time ratio of 1, a mass ratio of 0.6, and an engine performance parameter of 4. This study did not attempt to make a recommendation rather provide the tools for the reader to select their own configuration based on their needs.

Propellant↗

NASA NTRSDate not supplied

Development and Testing of a Lab-Scale Electrochemical Refrigerator

Eta Space and NASA have been developing a lab-scale electrochemical hydrogen refrigerator (ECHR) capable of providing isothermal heat exchange for applications in the 20-Kelvin range. The cryocooler utilizes an electrochemical compressor paired with Joule-Thomson expansion to cool the hydrogen working fluid down to its saturation point within a purpose-built cold box. The use of electrochemical compression allows the cycle to operate with no moving parts presenting several key advantages for a variety of applications. Testing of the integrated system occurred in Eta Space’s cryogenic test facility where the system was able to achieve and maintain saturated temperatures at low pressure. Results of this test campaign demonstrate the feasibility of the ECHR concept in practice.

D J Hollibaugh↗

NASA NTRSDate not supplied

Effect of Engine Thrust and Isp Tradeoffs and Alternate Propellants on ΔV Budget and Architecture Mass for 1st Generation Nuclear Thermal Propulsion Flight Test Systems

Following the first Nuclear Thermal Propulsion (NTP) system test, also known as DRACO, the next NTP system to be developed would be the 1st Generation NTP system. An analysis was conducted to determine the performance of different vehicle configurations utilizing hydrogen (H-NTP), ammonia (A-NTP), and methane (M-NTP) as propellants launched onboard commercial launch vehicles. This was enabled by a quasi-steady-state power balance engine model and vehicle component physics that sized the vehicle system using Master Equipment List (MEL) parameters. The analysis considered configuration cases outlined by a matrix of different mission classes and vehicle configurations that covered the design space of the 1st Generation NTP system to explore various propellant options, engine architectures, and mission scopes. Four mission classes were evaluated which included single burn missions performing maneuvers having a ΔV of 1 km/s and 2.5 km/s followed by 2-burn and 4-burn missions that aimed to exhaust the launch vehicles volume or mass limitations. In all cases, the NTP systems with the lowest thrust class had the longest burn time of which A-NTP and M-NTP systems provided the longest and shortest burn times depending on the launch vehicle used while H-NTP systems tended to cluster together in the middle. Longer burn times could be useful as a testing platform to increase the time for data accumulation. Across the multi-burn cases, H-NTP systems were found to be volume limited while A-NTP and M-NTP systems were mass limited. Both single burn missions showed that A-NTP configurations provided the lowest dry mass given that ammonia had the highest density with comparable performance to M-NTP systems and no requirement for cryocoolers. The results showed that beyond the propellant selection type, the launch vehicle selection, which included Starship, New Glenn, Vulcan, Falcon 9 (recoverable), and Falcon Heavy (recoverable), was a primary driving factor in the test vehicle’s capabilities. Trends were determined based on a set of dimensionless parameters that included the mass ratio of inert mass to initial wetted mass, ratio of specific impulse to burn time, and a dimensionless engine parameter (ratio of impulse to engine momentum). These relationships found the “knees-in-the-curves” that could be a significant point of reference for the designer as they indicate a change in the trend which is located at a specific impulse to burn time ratio of 1, a mass ratio of 0.6, and an engine performance parameter of 4. This study did not attempt to make a recommendation rather provide the tools for the reader to select their own configuration based on their needs.

Propellant↗

NASA NTRSDate not supplied

Effect of Engine Thrust and Isp Tradeoffs and Alternate Propellants on ΔV Budget and Architecture Mass for 1st Generation Nuclear Thermal Propulsion Flight Test Systems

Following the first Nuclear Thermal Propulsion (NTP) system test, also known as DRACO, the next NTP system to be developed would be the 1st Generation NTP system. An analysis was conducted to determine the performance of different vehicle configurations utilizing hydrogen (H-NTP), ammonia (A-NTP), and methane (M-NTP) as propellants launched onboard commercial launch vehicles. This was enabled by a quasi-steady-state power balance engine model and vehicle component physics that sized the vehicle system using Master Equipment List (MEL) parameters. The analysis considered configuration cases outlined by a matrix of different mission classes and vehicle configurations that covered the design space of the 1st Generation NTP system to explore various propellant options, engine architectures, and mission scopes. Four mission classes were evaluated which included single burn missions performing maneuvers having a ΔV of 1 km/s and 2.5 km/s followed by 2-burn and 4-burn missions that aimed to exhaust the launch vehicles volume or mass limitations. In all cases, the NTP systems with the lowest thrust class had the longest burn time of which A-NTP and M-NTP systems provided the longest and shortest burn times depending on the launch vehicle used while H-NTP systems tended to cluster together in the middle. Longer burn times could be useful as a testing platform to increase the time for data accumulation. Across the multi-burn cases, H-NTP systems were found to be volume limited while A-NTP and M-NTP systems were mass limited. Both single burn missions showed that A-NTP configurations provided the lowest dry mass given that ammonia had the highest density with comparable performance to M-NTP systems and no requirement for cryocoolers. The results showed that beyond the propellant selection type, the launch vehicle selection, which included Starship, New Glenn, Vulcan, Falcon 9 (recoverable), and Falcon Heavy (recoverable), was a primary driving factor in the test vehicle’s capabilities. Trends were determined based on a set of dimensionless parameters that included the mass ratio of inert mass to initial wetted mass, ratio of specific impulse to burn time, and a dimensionless engine parameter (ratio of impulse to engine momentum). These relationships found the “knees-in-the-curves” that could be a significant point of reference for the designer as they indicate a change in the trend which is located at a specific impulse to burn time ratio of 1, a mass ratio of 0.6, and an engine performance parameter of 4. This study did not attempt to make a recommendation rather provide the tools for the reader to select their own configuration based on their needs.

Propellant↗

NASA NTRSDate not supplied

Development of an Additively Manufactured Subscale Secondary Sealed Container for the NASA FROSTE Project

This presentation details the development of an additively manufactured (AM) subscale test article for the secondary sealed container (SSC) as part of the NASA FROSTE project. FROSTE is focused on the collection of regolith samples from shadowed regions of the Moon and the preservation of those samples at cryogenic temperatures for return to Earth. Our team was integrated into the FROSTE program to leverage innovative design approaches and additive manufacturing capabilities in support of a scalable development strategy, where the subscale configuration serves as the development path toward a full-scale SSC. Scalmalloy was selected as the primary material for all AM components due to its favorable strength-to-weight ratio, thermal conductivity, and demonstrated performance in aerospace applications. Its aluminum-based composition supports robust mechanical behavior at cryogenic temperatures while enabling efficient heat transfer and control of thermal gradients within the containment system. The SSC architecture consists of an outer container assembly that houses a phase change material (PCM) tank, which in turn contains primary containers holding the regolith. Thermal management relies on controlled conductive and radiative heat transfer, including a thermal connection assembly that interfaces the PCM tank to an external cryocooler via a thermal strap, and IMLI surrounding the PCM tank to inhibit radiative heat transfer. The outer container assembly incorporates sealing interfaces, thermal connection ports, and I/O feedthroughs, with PTFE spring seals used at critical interfaces to maintain containment integrity. The PCM tank is manufactured as a single monolithic Scalmalloy component and incorporates an integral lattice structure to minimize thermal gradients, internal channels for thermocouple routing, and interface features for thermal connection assembly integration. The tank is centrally suspended within the outer container using support rings, with G10 insulating components employed to inhibit thermal leaks. This work describes the design methodology, AM approach, and key considerations used to inform the design.

regolith↗

NASA NTRS2026

Mechanical Design and Operation of a Novel Lunar Environment Structural Test Rig (LESTR)

The Lunar Environment Structural Test Rig (LESTR) was developed to address a critical gap in mechanical property data for metal alloy wire materials under lunar-relevant conditions down to 40 K. Conventional aerospace material databases provide thermophysical properties for bulk metals over a wide temperature range, but validated mechanical and physical property data below 77 K, particularly for small-diameter wires, remain limited and are generally the exception rather than the rule. These conditions are essential for Artemis mission hardware such as shape memory alloy (SMA) rover tires. LESTR’s design requirements were to combine a high-stiffness electrodynamic load frame with closed- cycle cryogenic cooling, high-vacuum capability (10–6 torr), and noncontact optical strain measurement to enable tensile, four-point bend, and fatigue testing of wires or other materials and geometries at temperatures from 40 to 125 K. These considerable requirements were merged with the need to lower the barrier of testing for the end user as measured in terms of cost-per-test cycle, safety improvement, and reduction in upkeep costs associated with state-of-the-art solutions associated with cryomechanical material characterization. The system incorporates modular gripping and alignment fixtures; precision thermal management using cryocoolers and embedded heaters; and integrated instrumentation for displacement, load, temperature, and vacuum control. Calibration procedures establish correlations between tooling and specimen temperature, ensuring accurate thermal conditions across the design envelope unbound by cryofluid conditions in heritage immersion-based test systems. Initial validation tests using Inconel (Special Metals Corp.) wire demonstrated accurate ultimate strength and post-yield behavior. The load frame operation was also verified under representative service conditions, including thermal cycling and prolonged fatigue loading. By generating mechanical property data at ultralow temperatures, LESTR fills a critical gap in existing materials databases and provides a scalable platform for iterative alloy development and durability assessment for planetary hardware. This capability supports NASA’s long-term objectives for surface exploration by enabling design confidence for components operating in extreme cryogenic environments.

LESTR↗

DOE OSTI2015

Cryogenic Considerations for Superconducting Magnet Design for the Material Plasma Exposure eXperiment

In order to determine long term performance of plasma facing components such as diverters and first walls for fusion devices, next generation plasma generators are needed. A Material Plasma Exposure eXperiment (MPEX) has been proposed to address this need through the generation of plasmas in front of the target with electron temperatures of 1-15 eV and electron densities of 1020 to 1021 m-3. Heat fluxes on target diverters could reach 20 MW/m2. In order generate this plasma, a unique radio frequency helicon source and heating of electrons and ions through Electron Bernstein Wave (EBW) and Ion Cyclotron Resonance Heating (ICRH) has been proposed. MPEX requires a series of magnets with non-uniform central fields up to 2 T over a 5m length in the heating and transport region and 1 T uniform central field over a 1-m length on a diameter of 1.3 m. Given the field requirements, superconducting magnets are under consideration for MPEX. In order to determine the best construction method for the magnets, the cryogenic refrigeration has been analyzed with respect to cooldown and operational performance criteria for open-cycle and closed-cycle systems, capital and operating costs of these system, and maturity of supporting technology such as cryocoolers. These systems will be compared within the context of commercially available magnet constructions to determine the most economical method for MPEX operation. The current state of the MPEX magnet design including details on possible superconducting magnet configurations will be presented.

Duckworth, Robert C↗

DOE OSTI2016

Design of a low-cost, compact SRF accelerator for flue gas and wastewater treatment

Funding is being requested pursuant to a proposal that was submitted and reviewed through the Portfolio Analysis and Management System (PAMS). PAMS Proposal ID: 222439. The proposed project consists of the design of a novel superconducting continuous-wave accelerator capable of providing a beam current of ~1 A at an energy of 1-2 MeV for the treatment of flue gases and wastewater streams. The novel approach consists on studying the feasibility of using a single-cell Nb cavity coated with a thin Nb3Sn layer of the inner surface and conductively cooled by to 4.2 K by cryocoolers inside a compact cryomodule. The proposed study will include beam transport simulations, thermal and mechanical engineering analysis of the cryomodule and a cost analysis for both the fabrications costs and the operational and maintenance costs of such accelerator. The outcome of the project will be a report summarizing the analysis and results from the design study.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2018

Operation Regime Analysis of Conduction Cooled Cavities through Multi-Physics Simulation

Euclid Techlabs in collaboration with Fermilab IARC (Batavia, IL) is developing industrial superconducting 10MeV electron linac [1, 2]. Cryocoolers are to be used for cooling instead of liquid helium bath to simplify the linac infrastructure [3]. The cavity linked to commercially available cryo-cooler cold head [4, 5] through highly conductive aluminium (AL) strips. However, this solution raises a problem of contact thermal resistance. This paper shows some results of Comsol multyphysics simulations of the cavity cooling by AL strips. Some insight was obtained on the acceptable range of contact resistance. Operation regimes were obtained at different accelerating gradients and cavity temperatures. The results of simula-tion are presented and discussed.

43 PARTICLE ACCELERATORS↗

DOE OSTI2021

Motivation and Development of a Compact Superconducting Accelerator for X-ray Medical Device Sterilization

Fermilab is developing a compact superconducting (CSRF) accelerator as a source of a high-power, high-energy electron beam to produce an x-ray beam comparable to $\geq$ 2 MCi of cobalt-60. As part of this development, we are presently assembling a 20 kW, 1.6 MeV prototype that incorporates the four enabling technologies described below. These technologies support a heat budget that is within the capacity of commercially available cryocoolers and eliminate the need for liquid cryogens. The use of superconducting technologies promises efficiencies, wall-plug to beam, of 80% or greater. A summary of the design and progress to date will be given. In addition, we will present a review of developments within the medical device sterilization industry that are motivating the development of this technology.

43 PARTICLE ACCELERATORS↗